Introducing Highly Redox‐Active Atomic Centers into Insertion‐Type Electrodes for Lithium‐Ion Batteries

The development of alternative anode materials with higher volumetric and gravimetric capacity allowing for fast delithiation and, even more important, lithiation is crucial for next‐generation lithium‐ion batteries. Herein, the development of a completely new active material is reported, which follows an insertion‐type lithiation mechanism, metal‐doped CeO₂. Remarkably, the introduction of carefully selected dopants, herein exemplified for iron, results in an increase of the achievable capacity by more than 200%, originating from the reduction of the dopant to the metallic state and additional space for the lithium ion insertion due to a significant off‐centering of the dopant atoms in the crystal structure, away from the original Ce site. In addition to the outstanding performance of such materials in high‐power lithium‐ion full‐cells, the selective reduction of the iron dopant under preservation of the crystal structure of the host material is expected to open up a new field of research.     

LiTFSI‐Free Spiro‐OMeTAD‐Based Perovskite Solar Cells with Power Conversion Efficiencies Exceeding 19%

To date, the most efficient perovskite solar cells (PSCs) employ an n–i–p device architecture that uses a 2,2′,7,7′‐tetrakis(N,N‐di‐p‐methoxyphenyl‐amine)‐9,9′‐spirobifluorene (spiro‐OMeTAD) hole‐transporting material (HTM), which achieves optimum conductivity with the addition of lithium bis(trifluoromethane)sulfonimide (LiTFSI) and air exposure. However, this additive along with its oxidation process leads to poor reproducibility and is detrimental to stability. Herein, a dicationic salt spiro‐OMeTAD(TFSI)₂, is employed as an effective p‐dopant to achieve power conversion efficiencies of 19.3% and 18.3% (apertures of 0.16 and 1.00 cm²) with excellent reproducibility in the absence of LiTFSI and air exposure. As far as it is known, these are the highest‐performing n–i–p PSCs without LiTFSI or air exposure. Comprehensive analysis demonstrates that precise control of the proportion of [spiro‐OMeTAD]⁺ directly provides high conductivity in HTM films with low series resistance, fast hole extraction, and lower interfacial charge recombination. Moreover, the spiro‐OMeTAD(TFSI)₂‐doped devices show improved stability, benefitting from well‐retained HTM morphology without forming aggregates or voids when tested under an ambient atmosphere. A facile approach is presented to fabricate highly efficient PSCs by replacing LiTFSI with spiro‐OMeTAD(TFSI)₂. Furthermore, this study provides an insight into the relationship between device performance and the HTM doping level.     

Review on Challenges and Recent Advances in the Electrochemical Performance of High Capacity Li‐ and Mn‐Rich Cathode Materials for Li‐Ion Batteries

Li and Mn‐rich layered oxides, xLi₂MnO₃·(1–x)LiMO₂ (M=Ni, Mn, Co), are promising cathode materials for Li‐ion batteries because of their high specific capacity that can exceed 250 mA h g^?1. However, these materials suffer from high 1^st cycle irreversible capacity, gradual capacity fading, low rate capability, a substantial charge‐discharge voltage hysteresis, and a large average discharge voltage decay during cycling. The latter detrimental phenomenon is ascribed to irreversible structural transformations upon cycling of these cathodes related to potentials ≥4.5 V required for their charging. Transition metal inactivation along with impedance increase and partial layered‐to‐spinel transformation during cycling are possible reasons for the detrimental voltage fade. Doping of Li, Mn‐rich materials by Na, Mg, Al, Fe, Co, Ru, etc. is useful for stabilizing capacity and mitigating the discharge‐voltage decay of xLi₂MnO₃·(1–x)LiMO₂ electrodes. Surface modifications by thin coatings of Al₂O₃, V₂O₅, AlF₃, AlPO₄, etc. or by gas treatment (for instance, by NH₃) can also enhance voltage and capacity stability during cycling. This paper describes the recent literature results and ongoing efforts from our groups to improve the performance of Li, Mn‐rich materials. Focus is also on preparation of cobalt‐free cathodes, which are integrated layered‐spinel materials with high reversible capacity and stable performance.     

Nitrogen‐Doping‐Induced Defects of a Carbon Coating Layer Facilitate Na‐Storage in Electrode Materials

A nitrogen‐doped, carbon‐coated Na₃V₂(PO₄)₃ cathode material is synthesized and the formation of doping type of nitrogen‐doped in carbon coating layer is systemically investigated. Three different carbon‐nitrogen species: pyridinic N, pyrrolic N, and quaternary N are identified. The most important finding is that different carbon‐nitrogen species in the carbon layer have different impacts on the improvement of the electrochemical properties of Na₃V₂(PO₄)₃. Pyridinic N and pyrrolic N significantly increase the electronic conductivity and create numerous extrinsic defects and active sites. Quaternary N only increases the electronic conductivity without creating extrinsic defects. Therefore, it is unexpectedly demonstrated that the Na₃V₂(PO₄)₃/C+N, in which with minimize content of quaternary N or exist most extrinsic defects, exhibits the best electrochemical performance, particularly the rate performance and cycling stability. For example, when the discharging rate increased from 0.2 C to 5 C, its capacity of 101.9 mAh g^?1 decays to 84.3 mAh g^?1 and an amazing capacity retention of 83% is achieved. Moreover, even at higher current density of 5 C, an excellent capacity retention of 93% is maintained even after 100 cycles.     

Model‐Based Investigation on the Mass Transfer and Adsorption Mechanisms of Mono‐Pegylated Lysozyme in Ion‐Exchange Chromatography

Recent studies highlighted the potential of PEGylated proteins to improve stabilities and pharmacokinetics of protein drugs. Ion‐exchange chromatography (IEX) is among the most frequently used purification methods for PEGylated proteins. However, the underlying physical mechanisms allowing for a separation of different PEGamers (proteins with a varying number of attached PEG molecules) are not yet fully understood. In this work, mechanistic chromatography modeling is applied to gain a deeper understanding of the mass transfer and adsorption/desorption mechanisms of mono‐PEGylated proteins in IEX. Using a combination of the general rate model (GRM) and the steric mass action (SMA) isotherm, simulation results in good agreement with the experimental data are achieved. During linear gradient elution of proteins attached with PEG of different molecular weight, similar peak heights, and peak shapes at constant gradient length are observed. A superimposed effect of increased desorption rate and reduced diffusion rate as a function of the hydrodynamic radius of PEGylated proteins is identified to be the reason of this anomaly. That is why the concept of the diffusion‐desorption‐compensation effect is proposed. In addition to the altered elution orders, PEGylation results in a considerable decrease of maximum binding capacity. By using the SMA model in a kinetic formulation, the adsorption behavior of PEGylated proteins in the highly concentrated state is described mechanistically. An exponential increase in the steric hindrance effect with increasing PEG molecular weight is observed. This suggests the formation of multiple PEG layers in the interstitial space between bound proteins and an associated shielding of ligands on the adsorber surface to be the cause of the reduced maximum binding capacity. The presented in silico approach thus complements the hitherto proposed theories on the binding mechanisms of PEGylated proteins in IEX.     

Right‐ and left‐handed three‐helix proteins. I. Experimental and simulation analysis of differences in folding and structure

Despite the large number of publications on three‐helix protein folding, there is no study devoted to the influence of handedness on the rate of three‐helix protein folding. From the experimental studies, we make a conclusion that the left‐handed three‐helix proteins fold faster than the right‐handed ones. What may explain this difference? An important question arising in this paper is whether the modeling of protein folding can catch the difference between the protein folding rates of proteins with similar structures but with different folding mechanisms. To answer this question, the folding of eight three‐helix proteins (four right‐handed and four left‐handed), which are similar in size, was modeled using the Monte Carlo and dynamic programming methods. The studies allowed us to determine the orders of folding of the secondary‐structure elements in these domains and amino acid residues which are important for the folding. The obtained data are in good correlation with each other and with the experimental data. Structural analysis of these proteins demonstrated that the left‐handed domains have a lesser number of contacts per residue and a smaller radius of cross section than the right‐handed domains. This may be one of the explanations of the observed fact. The same tendency is observed for the large dataset consisting of 332 three‐helix proteins (238 right‐ and 94 left‐handed). From our analysis, we found that the left‐handed three‐helix proteins have some less‐dense packing that should result in faster folding for some proteins as compared to the case of right‐handed proteins.Proteins 2013; © 2013 Wiley Periodicals, Inc.     

Site‐Selective In Situ Electrochemical Doping for Mn‐Rich Layered Oxide Cathode Materials in Lithium‐Ion Batteries

Various doped materials have been investigated to improve the structural stability of layered transition metal oxides for lithium‐ion batteries. Most doped materials are obtained through solid state methods, in which the doping of cations is not strictly site selective. This paper demonstrates, for the first time, an in situ electrochemical site‐selective doping process that selectively substitutes Li⁺ at Li sites in Mn‐rich layered oxides with Mg²⁺. Mg²⁺ cations are electrochemically intercalated into Li sites in delithiated Mn‐rich layered oxides, resulting in the formation of [Li_1?xMg_y][Mn_1?zM_z]O₂ (M = Co and Ni). This Mg²⁺ intercalation is irreversible, leading to the favorable doping of Mg²⁺ at the Li sites. More interestingly, the amount of intercalated Mg²⁺ dopants increases with the increasing amount of Mn in Li_1?x[Mn_1?zM_z]O₂, which is attributed to the fact that the Mn‐to‐O electron transfer enhances the attractive interaction between Mg²⁺ dopants and electronegative O^δ? atoms. Moreover, Mg²⁺ at the Li sites in layered oxides suppresses cation mixing during cycling, resulting in markedly improved capacity retention over 200 cycles. The first‐principle calculations further clarify the role of Mg²⁺ in reduced cation mixing during cycling. The new concept of in situ electrochemical doping provides a new avenue for the development of various selectively doped materials.     

High‐Performance Lithium‐Sulfur Batteries with a Self‐Supported, 3D Li2S‐Doped Graphene Aerogel Cathodes

Lithium‐sulfur (Li‐S) batteries are being considered as the next‐generation high‐energy‐storage system due to their high theoretical energy density. However, the use of a lithium‐metal anode poses serious safety concerns due to lithium dendrite formation, which causes short‐circuiting, and possible explosions of the cell. One feasible way to address this issue is to pair a fully lithiated lithium sulfide (Li₂S) cathode with lithium metal‐free anodes. However, bulk Li₂S particles face the challenges of having a large activation barrier during the initial charge, low active‐material utilization, poor electrical conductivity, and fast capacity fade, preventing their practical utility. Here, the development of a self‐supported, high capacity, long‐life cathode material is presented for Li‐S batteries by coating Li₂S onto doped graphene aerogels via a simple liquid infiltration–evaporation coating method. The resultant cathodes are able to lower the initial charge voltage barrier and attain a high specific capacity, good rate capability, and excellent cycling stability. The improved performance can be attributed to the (i) cross‐linked, porous graphene network enabling fast electron/ion transfer, (ii) coated Li₂S on graphene with high utilization and a reduced energy barrier, and (iii) doped heteroatoms with a strong binding affinity toward Li₂S/lithium polysulfides with reduced polysulfide dissolution based on first‐principles calculations.     

Shear‐induced diffusion of red blood cells measured with dynamic light scattering‐optical coherence tomography

Quantitative measurements of intravascular microscopic dynamics, such as absolute blood flow velocity, shear stress and the diffusion coefficient of red blood cells (RBCs), are fundamental in understanding the blood flow behavior within the microcirculation, and for understanding why diffuse correlation spectroscopy (DCS) measurements of blood flow are dominantly sensitive to the diffusive motion of RBCs. Dynamic light scattering‐optical coherence tomography (DLS‐OCT) takes the advantages of using DLS to measure particle flow and diffusion within an OCT resolution‐constrained three‐dimensional volume, enabling the simultaneous measurements of absolute RBC velocity and diffusion coefficient with high spatial resolution. In this work, we applied DLS‐OCT to measure both RBC velocity and the shear‐induced diffusion coefficient within penetrating venules of the somatosensory cortex of anesthetized mice. Blood flow laminar profile measurements indicate a blunted laminar flow profile and the degree of blunting decreases with increasing vessel diameter. The measured shear‐induced diffusion coefficient was proportional to the flow shear rate with a magnitude of ~0.1 to 0.5 × 10^?6 mm². These results provide important experimental support for the recent theoretical explanation for why DCS is dominantly sensitive to RBC diffusive motion.      

Codoped Holey Graphene Aerogel by Selective Etching for High‐Performance Sodium‐Ion Storage

The pursuit of more efficient carbon‐based anodes for sodium‐ion batteries (SIBs) prepared from facile and economical methods is a very important endeavor. Based on the crystallinity difference within carbon materials, herein, a low‐temperature selective burning method is developed for preparing oxygen and nitrogen codoped holey graphene aerogel as additive‐free anode for SIBs. By selective burning of a mixture of graphene and low‐crystallinity carbon at 450 °C in air, an elastic porous graphene monolith with abundant holes on graphene sheets and optimized crystallinity is obtained. These structural characteristics lead to an additive‐free electrode with fast charge (ions and electrons) transfer and more abundant Na⁺ storage active sites. Moreover, the heteroatom oxygen/nitrogen doping favors large interlayer distance for rapid Na⁺ insertion/extraction and provides more active sites for high capacitive contribution. The optimized sample exhibits superior sodium‐ion storage capability, i.e., high specific capacity (446 mAh g^?1 at 0.1 A g^?1), ultrahigh rate capability (189 mAh g^?1 at 10 A g^?1), and long cycle life (81.0% capacity retention after 2000 cycles at 5 A g^?1). This facile and economic strategy might be extended to fabricating other superior carbon‐based energy storage materials.     

Ti‐Gradient Doping to Stabilize Layered Surface Structure for High Performance High‐Ni Oxide Cathode of Li‐Ion Battery

High‐Ni layered oxide cathodes are considered to be one of the most promising cathodes for high‐energy‐density lithium‐ion batteries due to their high capacity and low cost. However, surfice residues, such as NiO‐type rock‐salt phase and Li₂CO₃, are often formed at the particle surface due to the high reactivity of Ni³⁺, and inevitably result in an inferior electrochemical performance, hindering the practical application. Herein, unprecedentedly clean surfaces without any surfice residues are obtained in a representative LiNi_0.8Co_0.2O₂ cathode by Ti‐gradient doping. High‐resolution transmission electron microscopy (TEM) reveals that the particle surface is composed of a disordered layered phase (≈6 nm in thickness) with the same rhombohedra structure as its interior. The formation of this disordered layered phase at the particle surface is electrochemically favored. It leads to the highest rate capacity ever reported and a superior cycling stability. First‐principles calculations further confirm that the excellent electrochemical performance has roots in the excellent chemical/structural stability of such a disordered layered structure, mainly arising from the improved robustness of the oxygen framework by Ti doping. This strategy of constructing the disordered layered phase at the particle surface could be extended to other high‐Ni layered transition metal oxides, which will contribute to the enhancement of their electrochemical performance.     

In‐situ Crosslinking and n‐Doping of Semiconducting Polymers and Their Application as Efficient Electron‐Transporting Materials in Inverted Polymer Solar Cells

In this study, we demonstrate in‐situ n‐doping and crosslinking of semiconducting polymers as efficient electron‐transporting materials for inverted configuration polymer solar cells. The semiconducting polymers were crosslinked with bis(perfluorophenyl) azide (bis‐PFPA) to form a robust solvent‐resistant film, thereby preventing solvent‐induced erosion during subsequent solution‐based device processing. In addition, chemical n‐doping of semiconducting polymers with (4‐(1,3‐dimethyl‐2,3‐dihydro‐1H‐benzoimidazol‐2‐yl)phenyl)dimethylamine (N‐DMBI) substantially improved the power conversion efficiency of solar cells from 0.69% to 3.42%. These results open the way for progress on generally applicable polymeric interface materials, providing not only high device performance but also an effective fabrication method for solution‐processed multilayer solar cell devices.     

Li‐ and Mn‐Rich Cathode Materials: Challenges to Commercialization

The lithium‐ and manganese‐rich (LMR) layered structure cathodes exhibit one of the highest specific energies (≈900 W h kg^?1) among all the cathode materials. However, the practical applications of LMR cathodes are still hindered by several significant challenges, including voltage fade, large initial capacity loss, poor rate capability and limited cycle life. Herein, we review the recent progress and in depth understandings on the application of LMR cathode materials from a practical point of view. Several key parameters of LMR cathodes that affect the LMR/graphite full‐cell operation are systematically analyzed. These factors include the first‐cycle capacity loss, voltage fade, powder tap density, and electrode density. New approaches to minimize the detrimental effects of these factors are highlighted in this work. We also provide perspectives for the future research on LMR cathode materials, focusing on addressing the fundamental problems of LMR cathodes while keeping practical considerations in mind.     

High Thermoelectric Performance in p‐type Polycrystalline Cd‐doped SnSe Achieved by a Combination of Cation Vacancies and Localized Lattice Engineering

Herein, a high figure of merit (ZT) of ≈1.7 at 823 K is reported in p‐type polycrystalline Cd‐doped SnSe by combining cation vacancies and localized‐lattice engineering. It is observed that the introduction of Cd atoms in SnSe lattice induce Sn vacancies, which act as p‐type dopants. A combination of facile solvothermal synthesis and fast spark plasma sintering technique boosts the Sn vacancy to a high level of ≈2.9%, which results in an optimum hole concentration of ≈2.6 × 10¹⁹ cm^?3 and an improved power factor of ≈6.9 µW cm^?1 K^?2. Simultaneously, a low thermal conductivity of ≈0.33 W m^?1 K^?1 is achieved by effective phonon scattering at localized crystal imperfections, as observed by detailed structural characterizations. Density functional theory calculations reveal that the role of Cd atoms in the SnSe lattice is to reduce the formation energy of Sn vacancies, which in turn lower the Fermi level down into the valence bands, generating holes. This work explores the fundamental Cd‐doping mechanisms at the nanoscale in a SnSe matrix and demonstrates vacancy and localized‐lattice engineering as an effective approach to boosting thermoelectric performance. The work provides an avenue in achieving high‐performance thermoelectric properties of materials.