Improved Cycling Performance of Li‐Excess Cation‐Disordered Cathode Materials upon Fluorine Substitution

The recent discovery of Li‐excess cation‐disordered rock salt cathodes has greatly enlarged the design space of Li‐ion cathode materials. Evidence of facile lattice fluorine substitution for oxygen has further provided an important strategy to enhance the cycling performance of this class of materials. Here, a group of Mn³⁺–Nb⁵⁺‐based cation‐disordered oxyfluorides, Li_1.2Mn³⁺_0.6+0.5xNb⁵⁺_0.2?0.5xO_2?xF_x (x = 0, 0.05, 0.1, 0.15, 0.2) is investigated and it is found that fluorination improves capacity retention in a very significant way. Combining spectroscopic methods and ab initio calculations, it is demonstrated that the increased transition‐metal redox (Mn³⁺/Mn⁴⁺) capacity that can be accommodated upon fluorination reduces reliance on oxygen redox and leads to less oxygen loss, as evidenced by differential electrochemical mass spectroscopy measurements. Furthermore, it is found that fluorine substitution also decreases the Mn³⁺‐induced Jahn–Teller distortion, leading to an orbital rearrangement that further increases the contribution of Mn‐redox capacity to the overall capacity.     

Boosting the Activity of BaCo0.4Fe0.4Zr0.1Y0.1O3−δ Perovskite for Oxygen Reduction Reactions at Low‐to‐Intermediate Temperatures through Tuning B‐Site Cation Deficiency

Doped perovskite oxides with the general formula of A_xA′_1?xB_yB′_1?yO₃ have been extensively exploited as the cathode materials of solid oxide fuel cells (SOFCs), but the performance at low‐to‐medium temperatures still needs improvement. BaCo_0.4Fe_0.4Zr_0.1Y_0.1O_3?δ (BCFZY) has been recently reported to show promising oxygen reduction reaction (ORR) activity under SOFCs' operating conditions. Here, it is reported that the activity of BCFZY can be further boosted via introducing a slight B‐site cation deficiency into the oxide lattice, and such an improvement is assigned to an increase in oxygen mobility that brings enhancement in both surface exchange and bulk diffusion kinetics. Specifically, materials with the nominal composition of Ba(Co_0.4Fe_0.4Zr_0.1Y_0.1)_0.975O_3?δ and Ba(Co_0.4Fe_0.4Zr_0.1Y_0.1)_0.95O_3?δ show significantly improved activity for ORR at reduced temperatures with the area specific resistances of 0.011 and 0.024 Ω cm² at 600 °C, as a comparison of 0.042 Ω cm² for the cation stoichiometric BCFZY. Excessive B‐site deficiencies, however, lead to the formation of impurity phases, which cause a block for charge transfer and, consequently, a reduction in electrode performance. Introducing a B‐site cation deficiency is a promising way to optimize the activity of perovskite oxides for ORR at reduced temperatures, but the degree of deficiency shall be carefully tuned.     

Grafting Benzenediazonium Tetrafluoroborate onto LiNixCoyMnzO2 Materials Achieves Subzero‐Temperature High‐Capacity Lithium‐Ion Storage via a Diazonium Soft‐Chemistry Method

Subzero‐temperature Li‐ion batteries (LIBs) are highly important for specific energy storage applications. Although the nickel‐rich layered lithium transition metal oxides(LiNi_xCo_yMn_zO₂) (LNCM) (x > 0.5, x + y +z = 1) are promising cathode materials for LIBs, their very slow Li‐ion diffusion is a main hurdle on the way to achieve high‐performance subzero‐temperature LIBs. Here, a class of low‐temperature organic/inorganic hybrid cathode materials for LIBs, prepared by grafting a conducting polymer coating on the surface of 3 µm sized LiNi_0.6Co_0.2Mn_0.2O₂ (LNCM‐3) material particles via a greener diazonium soft‐chemistry method is reported. Specifically, LNCM‐3 particles are uniformly coated with a thin polyphenylene film via the spontaneous reaction between LNCM‐3 and C₆H₅N₂⁺BF₄^?. Compared with the uncoated one, the polyphenylene‐coated LNCM‐3 (polyphenylene/LNCM‐3) has shown much improved low‐temperature discharge capacity (≈148 mAh g^?1 at 0.1 C, ?20 °C), outstanding rate capability (≈105 mAh g^?1 at 1 C, ?20 °C), and superior low‐temperature long‐term cycling stability (capacity retention is up to 90% at 0.5 C over 1150 cycles). The low‐temperature performance of polyphenylene/LNCM‐3 is the best among the reported state‐of‐the art cathode materials for LIBs. The present strategy opens up a new avenue to construct advanced cathode materials for wider range applications.     

Synthesis and Characterization of High‐Energy,High‐Power Spinel‐Layered Composite Cathode Materials for Lithium‐Ion Batteries

Spinel‐layered composites, where a high‐voltage spinel is incorporated in a layered lithium‐rich (Li‐rich) cathode material with a nominal composition x{0.6Li₂MnO₃ · 0.4[LiCo_0.333Mn_0.333Ni_0.333]O₂} · (1 – x) Li[Ni_0.5Mn_1.5]O₄ (x = 0, 0.3, 0.5, 0.7, 1) are synthesized via a hydroxide assisted coprecipitation route to generate high‐energy, high‐power cathode materials for Li‐ion batteries. X‐ray diffraction patterns and the cyclic voltammetry investigations confirm the presence of both the parent components in the composites. The electrochemical investigations performed within a wide potential window show an increased structural stability of the spinel component when incorporated into the composite environment. All the composite materials exhibit initial discharge capacities >200 mAh g^–1. The compositions with x = 0.5 and 0.7 show excellent cycling stability among the investigated materials. Moreover, the first cycle Coulombic efficiency achieve a dramatic improvement with the incorporation of the spinel component. More notably, the composite materials with increased spinel component exhibit superior rate capability compared with the parent Li‐rich material especially together with the highest capacity retention for x = 0.5 composition, making this as the optimal high‐energy high‐power material. The mechanisms involved in the symbiotic relationship of the spinel and layered Li‐rich components in the above composites are discussed.     

An Ion‐Exchange Promoted Phase Transition in a Li‐Excess Layered Cathode Material for High‐Performance Lithium Ion Batteries

A new approach to intentionally induce phase transition of Li‐excess layered cathode materials for high‐performance lithium ion batteries is reported. In high contrast to the limited layered‐to‐spinel phase transformation that occurred during in situ electrochemical cycles, a Li‐excess layered Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ is completely converted to a Li₄Mn₅O₁₂‐type spinel product via ex situ ion‐exchanges and a post‐annealing process. Such a layered‐to‐spinel phase conversion is examined using in situ X‐ray diffraction and in situ high‐resolution transmission electron microscopy. It is found that generation of sufficient lithium ion vacancies within the Li‐excess layered oxide plays a critical role for realizing a complete phase transition. The newly formed spinel material exhibits initial discharge capacities of 313.6, 267.2, 204.0, and 126.3 mAh g^?1 when cycled at 0.1, 0.5, 1, and 5 C (1 C = 250 mA g^?1), respectively, and can retain a specific capacity of 197.5 mAh g^?1 at 1 C after 100 electrochemical cycles, demonstrating remarkably improved rate capability and cycling stability in comparison with the original Li‐excess layered cathode materials. This work sheds light on fundamental understanding of phase transitions within Li‐excess layered oxides. It also provides a novel route for tailoring electrochemical performance of Li‐excess layered cathode materials for high‐capacity lithium ion batteries.     

Understanding Performance Degradation in Cation‐Disordered Rock‐Salt Oxide Cathodes

The collective redox activities of transition‐metal (TM) cations and oxygen anions have been shown to increase charge storage capacity in both Li‐rich layered and cation‐disordered rock‐salt cathodes. Repeated cycling involving anionic redox is known to trigger TM migration and phase transformation in layered Li‐ and Mn‐rich (LMR) oxides, however, detailed mechanistic understanding on the recently discovered Li‐rich rock‐salt cathodes is largely missing. The present study systematically investigates the effect of oxygen redox on a Li_1.3Nb_0.3Mn_0.4O₂ cathode and demonstrates that performance deterioration is directly correlated to the extent of oxygen redox. It is shown that voltage fade and hysteresis begin only after initiating anionic redox at high voltages, which grows progressively with either deeper oxidation of oxygen at higher potential or extended cycling. In contrast to what is reported on layered LMR oxides, extensive TM reduction is observed but phase transition is not detected in the cycled oxide. A densification/degradation mechanism is proposed accordingly which elucidates how a unique combination of extensive chemical reduction of TM and reduced quality of the Li percolation network in cation‐disordered rock‐salts can lead to performance degradation in these newer cathodes with 3D Li migration pathways. Design strategies to achieve balanced capacity and stability are also discussed.     

Spinel‐Layered Core‐Shell Cathode Materials for Li‐Ion Batteries

In an attempt to overcome the problems associated with LiNiO₂, the solid solution series of lithium nickel‐metal oxides, Li[Ni_1–xM_x]O₂ (with M = Co, Mn, Al, Ti, Mg, etc.), have been investigated as favorable cathode materials for high‐energy and high‐power lithium‐ion batteries. However, along with the improvement in the electrochemical properties in Ni‐based cathode materials, the thermal stability has been a great concern, and thus violent reaction of the cathode with the electrolyte needs to be avoided. Here, we report a heterostructured Li[Ni_0.54Co_0.12Mn_0.34]O₂ cathode material which possesses both high energy and safety. The core of the particle is Li[Ni_0.54Co_0.12Mn_0.34]O₂ with a layered phase (R3‐m) and the shell, with a thickness of < 0.5 μm, is a highly stable Li_1+x[CoNi_xMn_2–x]₂O₄ spinel phase (Fd‐3m). The material demonstrates reversible capacity of 200 mAhg‐1 and retains 95% capacity retention under the most severe test condition of 60 °C. In addition, the amount of oxygen evolution from the lattice in the cathode with two heterostructures is reduced by 70%, compared to the reference sample. All these results suggest that the bulk Li[Ni_0.54Co_0.12Mn_0.34]O₂ consisting of two heterostructures satisfy the requirements for hybrid electric vehicles, power tools, and mobile electronics.     

Controlled Atomic Solubility in Mn‐Rich Composite Material to Achieve Superior Electrochemical Performance for Li‐Ion Batteries

The quest for high energy density and high power density electrode materials for lithium‐ion batteries has been intensified to meet strongly growing demand for powering electric vehicles. Conventional layered oxides such as Co‐rich LiCoO₂ and Ni‐rich Li(Ni_xMn_yCo_z)O₂ that rely on only transition metal redox reaction have been faced with growing constraints due to soaring price on cobalt. Therefore, Mn‐rich electrode materials excluding cobalt would be desirable with respect to available resources and low cost. Here, the strategy of achieving both high energy density and high power density in Mn‐rich electrode materials by controlling the solubility of atoms between phases in a composite is reported. The resulting Mn‐rich material that is composed of defective spinel phase and partially cation‐disordered layered phase can achieve the highest energy density, ≈1100 W h kg^?1 with superior power capability up to 10C rate (3 A g^?1) among other reported Mn‐rich materials. This approach provides new opportunities to design Mn‐rich electrode materials that can achieve high energy density and high power density for Li‐ion batteries.     

Layered Na‐Ion Cathodes with Outstanding Performance Resulting from the Synergetic Effect of Mixed P‐ and O‐Type Phases

Herein, the synthesis of new quaternary layered Na‐based oxides of the type Na_xMn_yNi_zFe_0.1Mg_0.1O₂ (0.67≤ x ≤ 1.0; 0.5≤ y ≤ 0.7; 0.1≤ z ≤ 0.3) is described. The synthesis can be tuned to obtain P2‐ and O3‐type as well as mixed P‐/O‐type phases as demonstrated by structural, morphological, and electrochemical properties characterization. Although all materials show good electrochemical performance, the simultaneous presence of the P‐ and O‐type phases is found to have a synergetic effect resulting in outstanding performance of the mixed phase material as a sodium‐ion cathode. The mixed P3/P2/O3‐type material, having an average elemental composition of Na_0.76Mn_0.5Ni_0.3Fe_0.1Mg_0.1O₂, overcomes the specific drawbacks associated with the P2‐ and O3‐type materials, allowing the outstanding electrochemical performance. In detail, the mixed phase material is able to deliver specific discharge capacities of up to 155 mAh g^?1 (18 mA g^?1) in the potential range of 2.0–4.3 V. In the narrower potential range of 2.5–4.3 V the material exhibits high average discharge potential (3.4 V versus Na/Na⁺), exceptional average coulombic efficiencies (>99.9%), and extraordinary capacity retention (90.2% after 601 cycles). The unexplored class of P‐/O‐type mixed phases introduces new perspectives for the development of layered positive electrode materials and powerful Na‐ion batteries.     

A New Strategy for High‐Voltage Cathodes for K‐Ion Batteries: Stoichiometric KVPO4F

The exploration of high‐energy‐density cathode materials is vital to the practical use of K‐ion batteries. Layered K‐metal oxides have too high a voltage slope due to their large K⁺–K⁺ interaction, resulting in low specific capacity and average voltage. In contrast, the 3D arrangement of K⁺, with polyanions separating them, reduces the strength of the effective K⁺‐K⁺ repulsion, which in turn increases specific capacity and voltage. Here, stoichiometric KVPO₄F for use as a high‐energy‐density K‐ion cathode is developed. The KVPO₄F cathode delivers a reversible capacity of ≈105 mAh g^?1 with an average voltage of ≈4.3 V (vs K/K⁺), resulting in a gravimetric energy density of ≈450 Wh kg^?1. During electrochemical cycling, the K_xVPO₄F cathode goes through various intermediate phases at x = 0.75, 0.625, and 0.5 upon K extraction and reinsertion, as determined by ex situ X‐ray diffraction characterization and ab initio calculations. This work further explains the role of oxygen substitution in KVPO_4+xF_1?x: the oxygenation of KVPO₄F leads to an anion‐disordered structure which prevents the formation of K⁺/vacancy orderings without electrochemical plateaus and hence to a smoother voltage profile.     

Site‐Selective In Situ Electrochemical Doping for Mn‐Rich Layered Oxide Cathode Materials in Lithium‐Ion Batteries

Various doped materials have been investigated to improve the structural stability of layered transition metal oxides for lithium‐ion batteries. Most doped materials are obtained through solid state methods, in which the doping of cations is not strictly site selective. This paper demonstrates, for the first time, an in situ electrochemical site‐selective doping process that selectively substitutes Li⁺ at Li sites in Mn‐rich layered oxides with Mg²⁺. Mg²⁺ cations are electrochemically intercalated into Li sites in delithiated Mn‐rich layered oxides, resulting in the formation of [Li_1?xMg_y][Mn_1?zM_z]O₂ (M = Co and Ni). This Mg²⁺ intercalation is irreversible, leading to the favorable doping of Mg²⁺ at the Li sites. More interestingly, the amount of intercalated Mg²⁺ dopants increases with the increasing amount of Mn in Li_1?x[Mn_1?zM_z]O₂, which is attributed to the fact that the Mn‐to‐O electron transfer enhances the attractive interaction between Mg²⁺ dopants and electronegative O^δ? atoms. Moreover, Mg²⁺ at the Li sites in layered oxides suppresses cation mixing during cycling, resulting in markedly improved capacity retention over 200 cycles. The first‐principle calculations further clarify the role of Mg²⁺ in reduced cation mixing during cycling. The new concept of in situ electrochemical doping provides a new avenue for the development of various selectively doped materials.     

Anion Reactivity in Cation‐Disordered Rocksalt Cathode Materials: The Influence of Fluorine Substitution

The demand for high energy‐density, mass‐producible cathode materials has spurred the exploration of new material structures and compositions. Lithium‐excess, cation‐disordered rocksalt (DRX) materials are a new class of transition metal oxides that display high capacity and environmental friendly composition. These materials achieve their high capacities partially through oxygen redox, which leads to oxygen loss and detrimental reactivity with the electrolyte. It has previously been shown that oxygen loss can be suppressed by partial substitution of the lattice oxygen for fluorine, but the explicit mechanism behind this effect remains unknown. In this work, differential electrochemical mass spectrometry (DEMS) and titration mass spectrometry are used to quantify the primary electrochemical reactions occurring during the first cycle in DRX materials. Comparing a DRX oxide and a DRX oxyfluoride, it is shown that fluorination limits oxygen redox and suppresses oxygen loss. Additionally, DEMS is coupled with fluoride‐scavenging to demonstrate that small amounts of fluorine dissolve from DRX oxyfluorides during the first cycle. Finally, these techniques are extended over the first several cycles, demonstrating that CO₂ evolution persists and fluoride dissolution continues to a diminishing extent during the first few cycles. These findings motivate surface modifications to control interfacial reactivity and improve long‐term cycling.     

A High‐Throughput Search for Functionally Stable Interfaces in Sulfide Solid‐State Lithium Ion Conductors

Interfacial reactions between ceramic‐sulfide solid‐electrolytes and common electrodes have remained a major impediment to the development of solid‐state lithium‐ion batteries. In practice, this means that ceramic‐sulfide batteries require a suitable coating material to isolate the electrolyte from the electrode materials. In this work, the interfacial stability of Li₁₀SiP₂S₁₂ with over 67 000 materials is computationally evaluated. Over 2000 materials that are predicted to form stable interfaces in the cathode voltage range and over 1000 materials for the anode range are reported on and cataloged. LiCoO₂ is chosen as an example cathode material to identify coating compounds that are stable with both Li₁₀SiP₂S₁₂ and a common cathode. The correlation between elemental composition and multiple instability metrics (e.g., chemical/electrochemical) is analyzed, revealing key trends in, amongst others, the role of anion selection. A new binary‐search algorithm is introduced for evaluating the pseudo‐phase with improved speed and accuracy. Computational challenges posed by high‐throughput interfacial phase‐diagram calculations are highlighted as well as pragmatic computational methods to make such calculations routinely feasible. In addition to the over 3000 materials cataloged, representative materials from the anionic classes of oxides, fluorides, and sulfides are chosen to experimentally demonstrate chemical stability when in contact with Li₁₀SiP₂S₁₂.     

Lattice‐Cell Orientation Disorder in Complex Spinel Oxides

Transition metal (TM) substitution has been widely applied to change complex oxides crystal structures to create high energy density electrodes materials in high performance rechargeable lithium‐ion batteries. The complex local structure in the oxides imparted by the TM arrangement often impacts their electrochemical behaviors by influencing the diffusion and intercalation of lithium. Here, a major discrepancy is demonstrated between the global and local structures of the promising high energy density and high voltage LiNi_0.5Mn_1.5O₄ spinel cathode material that contradicts the existing structural models. A new single‐phase lattice‐cell orientation disorder model is proposed as the mechanism for the local ordering that explains how the inhomogeneous local distortions and the coherent connection give rise to the global structure in the complex oxide. Further, the single‐phase model is consistent with the electrochemical behavior observation of the materials.     

Suppression of Voltage Decay through Manganese Deactivation and Nickel Redox Buffering in High‐Energy Layered Lithium‐Rich Electrodes

Cobalt‐free layered lithium‐rich nickel manganese oxides, Li[Li_xNi_yMn_1?x?y]O₂ (LLNMO), are promising positive electrode materials for lithium rechargeable batteries because of their high energy density and low materials cost. However, substantial voltage decay is inevitable upon electrochemical cycling, which makes this class of materials less practical. It has been proposed that undesirable voltage decay is linked to irreversible structural rearrangement involving irreversible oxygen loss and cation migration. Herein, the authors demonstrate that the voltage decay of the electrode is correlated to Mn⁴⁺/Mn³⁺ redox activation and subsequent cation disordering, which can be remarkably suppressed via simple compositional tuning to induce the formation of Ni³⁺ in the pristine material. By implementing our new strategy, the Mn⁴⁺/Mn³⁺ reduction is subdued by an alternative redox reaction involving the use of pristine Ni³⁺ as a redox buffer, which has been designed to be widened from Ni³⁺/Ni⁴⁺ to Ni²⁺/Ni⁴⁺, without compensation for the capacity in principle. Negligible change in the voltage profile of modified LLNMO is observed upon extended cycling, and manganese migration into the lithium layer is significantly suppressed. Based on these findings, we propose a general strategy to suppress the voltage decay of Mn‐containing lithium‐rich oxides to achieve long‐lasting high energy density from this class of materials.     

Understanding the Rate Capability of High‐Energy‐Density Li‐Rich Layered Li1.2Ni0.15Co0.1Mn0.55O2 Cathode Materials

The high‐energy‐density, Li‐rich layered materials, i.e., xLiMO₂(1‐x)Li₂MnO₃, are promising candidate cathode materials for electric energy storage in plug‐in hybrid electric vehicles (PHEVs) and electric vehicles (EVs). The relatively low rate capability is one of the major problems that need to be resolved for these materials. To gain insight into the key factors that limit the rate capability, in situ X‐ray absorption spectroscopy (XAS) and X‐ray diffraction (XRD) studies of the cathode material, Li_1.2Ni_0.15Co_0.1Mn_0.55O₂ [0.5Li(Ni_0.375Co_0.25 Mn_0.375)O₂·0.5Li₂MnO₃], are carried out. The partial capacity contributed by different structural components and transition metal elements is elucidated and correlated with local structure changes. The characteristic reaction kinetics for each element are identified using a novel time‐resolved XAS technique. Direct experimental evidence is obtained showing that Mn sites have much poorer reaction kinetics both before and after the initial activation of Li₂MnO₃, compared to Ni and Co. These results indicate that Li₂MnO₃ may be the key component that limits the rate capability of Li‐rich layered materials and provide guidance for designing Li‐rich layered materials with the desired balance of energy density and rate capability for different applications.     

Thermodynamic Aspects of Cathode Coatings for Lithium‐Ion Batteries

Metal oxide cathode coatings are capable of scavenging the hydrofluoric acid (HF) (present in LiPF₆‐based electrolytes) and improving the electrochemical performance of Li‐ion batteries. Here, a first‐principles thermodynamic framework is introduced for designing cathode coatings that consists of four elements: i) HF‐scavenging enthalpies, ii) volumetric and iii) gravimetric HF‐scavenging capacities of the oxides, and iv) cyclable Li loss into coating components. 81 HF‐scavenging reactions involving binary s‐, p‐ and d‐block metal oxides and fluorides are enumerated and these materials are screened to find promising coatings based on attributes (i‐iv). The screen successfully produces known effective coating materials (e.g., Al₂O₃ and MgO), providing a validation of our framework. Using this design strategy, promising coating materials, such as trivalent oxides of d‐block transition metals Sc, Ti, V, Cr, Mn and Y, are predicted. Finally, a new protection mechanism that successful coating materials could provide by scavenging the wide bandgap and low Li ion conductivity LiF precipitates from the cathode surfaces is suggested.     

Countering Voltage Decay and Capacity Fading of Lithium‐Rich Cathode Material at 60 °C by Hybrid Surface Protection Layers

Li‐rich layered metal oxides have attracted much attention for their high energy density but still endure severe capacity fading and voltage decay during cycling, especially at elevated temperature. Here, facile surface treatment of Li_1.17Ni_0.17Co_0.17Mn_0.5O₂ (0.4Li₂MnO₃·0.6LiNi_1/3Co_1/3Mn_1/3O₂) spherical cathode material is designed to address these drawbacks by hybrid surface protection layers composed of Mg²⁺ pillar and Li‐Mg‐PO₄ layer. As a result, the surface coated Li‐rich cathode material exhibits much enhanced cycling stability at 60 °C, maintaining 72.6% capacity retention (180 mAh g^?1) between 3.0 and 4.7 V after 250 cycles. More importantly, 88.7% average discharge voltage retention can be obtained after the rigorous cycle test. The strategy developed here with novel hydrid surface protection effect can provide a vital approach to inhibit the undesired side reactions and structural deterioration of Li‐rich cathode materials and may also be useful for other layered oxides to increase their cycling stability at elevated temperature.     

Anion Doping: A New Strategy for Developing High‐Performance Perovskite‐Type Cathode Materials of Solid Oxide Fuel Cells

Overcoming the sluggish activity of cathode materials is critical to realizing the wide‐spread application of intermediate‐temperature solid oxide fuel cells. Herein, a new way is reported to tune the performance of perovskite‐type materials as oxygen reduction electrodes by embedding anions (F^?) in oxygen sites. The obtained perovskite oxyfluorides SrFeO_{3?σ ?δ} F_σ and SrFe_0.9Ti_0.1O_{3?σ ?δ} F_σ (σ = 0.05 and 0.10) show improved electrocatalytic activity compared to their parent oxides, achieving area specific resistance values of 0.875, 0.393, and 0.491 Ω cm² for SrFeO_3?δ , SrFeO_2.95?δ F_0.05, and SrFeO_2.90?δ F_0.10, respectively, at 600 °C in air. Such improved performance is a result of the improved bulk diffusion and surface exchange properties due to anion doping. Moreover, favorable stability in performance is also demonstrated for the F^? anion‐doped perovskites as oxygen reduction electrodes at 650 °C for a test period of ≈200 h. A combination of anion doping and cation doping may provide a highly attractive strategy for the future development of cathode materials.     

Lithium/Oxygen Incorporation and Microstructural Evolution during Synthesis of Li‐Rich Layered Li[Li0.2Ni0.2Mn0.6]O2 Oxides

As promising cathode materials, the lithium‐excess 3d‐transition‐metal layered oxides can deliver much higher capacities (>250 mAh g^?1 at 0.1 C) than the current commercial layered oxide materials (≈180 mAh g^?1 at 0.1 C) used in lithium ion batteries. Unfortunately, the original formation mechanism of these layered oxides during synthesis is not completely elucidated, that is, how is lithium and oxygen inserted into the matrix structure of the precursor during lithiation reaction? Here, a promising and practical method, a coprecipitation route followed by a microwave heating process, for controllable synthesis of cobalt‐free lithium‐excess layered compounds is reported. A series of the consistent results unambiguously confirms that oxygen atoms are successively incorporated into the precursor obtained by a coprecipitation process to maintain electroneutrality and to provide the coordination sites for inserted Li ions and transition metal cations via a high‐temperature lithiation. It is found that the electrochemical performances of the cathode materials are strongly related to the phase composition and preparation procedure. The monoclinic layered Li[Li_0.2Ni_0.2Mn_0.6]O₂ cathode materials with state‐of‐the‐art electrochemical performance and comparably high discharge capacities of 171 mAh g^?1 at 10 C are obtained by microwave annealing at 750 °C for 2 h.