Understanding the Morphology of PTB7:PCBM Blends in Organic Photovoltaics

The structure–property relationships of PTB7‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM)‐based organic photovoltaics are investigated. The morphology is investigated in an active layer setting where a multi‐length‐scale morphology is observed using a solvent additive‐assisted film processing. This multi‐length‐scale structure consists of a phase separated morphology with a characteristic length scale of ≈30 nm, which is critical for producing large currents in devices; a second length scale of ≈130 nm, arises from face‐on PTB7 crystalline aggregates. This latter morphological feature is also observed in films prepared without the use of an additive. By observing the structure formation in situ during solvent evaporation for blade coated thin films, the additive is found to promote the formation of ordered domains of the PTB7 at an earlier stage during the solvent evaporation, which is critical in the development of the final morphology. In studies on PTB7/PCBM bilayers, PCBM is found to diffuse into the PTB7 layer. However, the performance of devices prepared in this manner is low. This diffusion leads to a swelling of the PTB7 and a reduction in the crystallinity of the PTB7, reflecting the strong miscibility of PCBM with PTB7. The morphology resulting from the interdiffusion is single‐length‐scale with slightly large phase separation. This leads to devices with poor performance.     

Electron Collection as a Limit to Polymer:PCBM Solar Cell Efficiency: Effect of Blend Microstructure on Carrier Mobility and Device Performance in PTB7:PCBM

The poor photovoltaic performance of state‐of‐the‐art blends of poly[4,8‐bis[(2‐ethylhexyl)oxy]benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]thieno[3,4‐b]thiophenediyl] (PTB7) and [6,6]‐phenyl‐C61‐butyric acid (PCBM) at large active layer thicknesses is studied using space‐charge‐limited current mobility and photovoltaic device measurements. The poor performance is found to result from relatively low electron mobility. This is attributed to the low tendency of PTB7 to aggregate, which reduces the ability of the fullerene to form a connected network. Increasing the PCBM content 60–80 wt% increases electron mobility and accordingly improves performance for thicker devices, resulting in a fill factor (FF) close to 0.6 at 300 nm. The result confirms that by improving only the connectivity of the fullerene phase, efficient electron and hole collection is possible for 300 nm‐thick PTB7:PCBM devices. Furthermore, it is shown that solvent additive 1,8‐diiodooctane (DIO), used in the highest efficiency PTB7:PCBM devices, does not improve the thickness dependence and, accordingly, does not lead to an increase in either hole or electron mobility or in the carrier lifetime. A key challenge for researchers is therefore to develop new methods to ensure connectivity in the fullerene phase in blends without relying on either a large excess of fullerene or strong aggregation of the polymer.     

Circumventing UV Light Induced Nanomorphology Disorder to Achieve Long Lifetime PTB7‐Th:PCBM Based Solar Cells

Large area flexible electronics rely on organic or hybrid materials prone to degradation limiting the device lifetime. For many years, photo‐oxidation has been thought to be one of the major degradation pathways. However, intense illumination may lead to a burn‐in or a rapid decrease in performance for devices completely isolated from corrosive elements as oxygen or moisture. The experimental studies which are presented in here indicate that a plausible triggering for the burn‐in is a spin flip after a UV photon absorption leading to the accumulation of electrostatic potential energy that initiates a rapid destruction of the nanomorpholgy in the fullerene phase of a polymer cell. To circumvent this and achieve highly stable and efficient devices, a robust nanocrystalline ordering is induced in the PCBM phase prior to UV illumination. In that event, PTB7‐Th:PC₇₁BM cells are shown to exhibit T₈₀ lifetimes larger than 1.6 years under a continuous UV‐filtered 1‐sun illumination, equivalent to 7 years for sunlight harvesting at optimal orientation and 10 years for vertical applications.     

Toward High‐Temperature Stability of PTB7‐Based Bulk Heterojunction Solar Cells: Impact of Fullerene Size and Solvent Additive

The use of fullerene as acceptor limits the thermal stability of organic solar cells at high temperatures as their diffusion inside the donor leads to phase separation via Ostwald ripening. Here it is reported that fullerene diffusion is fully suppressed at temperatures up to 140 °C in bulk heterojunctions based on the benzodithiophene‐based polymer (the poly[[4,8‐bis[(2‐ethylhexyl)oxy]‐benzo[1,2‐b:4,5‐b′]dithiophene‐2,6‐diyl][3‐fluoro‐2‐[(2‐ethylhexyl)carbonyl]‐thieno[3,4‐b]thiophenediyl]], (PTB7) in combination with the fullerene derivative [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₀BM). The blend stability is found independently of the presence of diiodooctane (DIO) used to optimize nanostructuration and in contrast to PTB7 blends using the smaller fullerene derivative PC₇₀BM. The unprecedented thermal stability of PTB7:PC₇₀BM layers is addressed to local minima in the mixing enthalpy of the blend forming stable phases that inhibit fullerene diffusion. Importantly, although the nanoscale morphology of DIO processed blends is thermally stable, corresponding devices show strong performance losses under thermal stress. Only by the use of a high temperature annealing step removing residual DIO from the device, remarkably stable high efficiency solar cells with performance losses less than 10% after a continuous annealing at 140 °C over 3 days are obtained. These results pave the way toward high temperature stable polymer solar cells using fullerene acceptors.     

Efficient Perovskite Solar Cells over a Broad Temperature Window: The Role of the Charge Carrier Extraction

The mechanism behind the temperature dependence of the device performance in hybrid perovskite solar cells (HPSCs) is investigated systematically. The power conversion efficiency (PCE) of the reference cell using [60]PCBM as electron extraction layer (EEL) drops significantly from 11.9% at 295 K to 7% at 180 K. The deteriorated charge carrier extraction is found as the dominant factor causing this degradation. Temperature dependent spectroscopy and charge transport studies demonstrate that the poor electron transport in the [60]PCBM EEL at low temperature leads to inefficient charge carrier extraction. It is further demonstrated that the n‐type doping of [60]PCBM EEL or the use of an EEL (fulleropyrrolidine with a triethylene glycol monoethyl ether side chain) with higher electron transport capability is an effective strategy to achieve HPSCs working efficiently over a broad temperature range. The devices fabricated with these highly performing EELs have PCEs at 180 K of 16.7% and 18.2%, respectively. These results support the idea that the temperature dependence of the electron transport in the EELs limits the device performance in HPSCs, especially at lower temperatures and they also give directions toward further improvement of the PCE of HPSCs at realistic operating temperatures.     

Intra‐Molecular Donor–Acceptor Interaction Effects on Charge Dissociation,Charge Transport,and Charge Collection in Bulk‐Heterojunction Organic Solar Cells

This article reports experimental studies on internal charge dissociation, transport, and collection by using magnetic field effects of photocurrent (MFE_PC) and light‐assisted dielectric response (LADR) in highly‐efficient organic solar cells based on photovoltaic polymer PTB2 and PTB4 with intra‐molecular “donor–acceptor” interaction. The MFE_PC at low‐field (< 150 mT) indicates that intra‐molecular “donor‐acceptor” interaction generates charge dissociation in un‐doped PTB2 and PTB4 films, which is similar to that in lightly doped P3HT (Poly(3‐hexylthiophene)) with 5 wt% PCBM (1‐(3‐methyloxycarbonyl)‐propyl‐1‐phenyl (6,6) C₆₁). After PTB2 and PTB4 are mixed with PCBM to form bulk‐heterojunctions, the MFE_PC at high‐field (> 150 mT) reveals that the charge‐transfer complexes formed at PTB2:PCBM and PTB4:PCBM interfaces have much lower binding energies due to stronger electron‐withdrawing abilities, as compared to the P3HT:PCBM device, towards the generation of photocurrent. Furthermore, the light‐assisted dielectric response: LADR indicates that the PTB2:PCBM and PTB4:PCBM solar cells exhibit larger capacitances relative to P3HT:PCBM device under photoexcitation. This reflects that the PTB2:PCBM and PTB4:PCBM bulk heterojunctions have more effective charge transport and collection than the P3HT:PCBM counterpart. As a result, our experimental results indicate that intra‐molecular “donor‐acceptor” interaction plays an important role to enhance charge dissociation, transport, and collection in bulk‐heterojunction organic solar cells.     

The Importance of Fullerene Percolation in the Mixed Regions of Polymer–Fullerene Bulk Heterojunction Solar Cells

Most optimized donor‐acceptor (D‐A) polymer bulk heterojunction (BHJ) solar cells have active layers too thin to absorb greater than ～80% of incident photons with energies above the polymer's band gap. If the thickness of these devices could be increased without sacrificing internal quantum efficiency, the device power conversion efficiency (PCE) could be significantly enhanced. We examine the device characteristics of BHJ solar cells based on poly(di(2‐ethylhexyloxy)benzo[1,2‐b:4,5‐b′]dithiophene‐co‐octylthieno[3,4‐c]pyrrole‐4,6‐dione) (PBDTTPD) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) with 7.3% PCE and find that bimolecular recombination limits the active layer thickness of these devices. Thermal annealing does not mitigate these bimolecular recombination losses and drastically decreases the PCE of PBDTTPD BHJ solar cells. We characterize the morphology of these BHJs before and after thermal annealing and determine that thermal annealing drastically reduces the concentration of PCBM in the mixed regions, which consist of PCBM dispersed in the amorphous portions of PBDTTPD. Decreasing the concentration of PCBM may reduce the number of percolating electron transport pathways within these mixed regions and create morphological electron traps that enhance charge‐carrier recombination and limit device quantum efficiency. These findings suggest that (i) the concentration of PCBM in the mixed regions of polymer BHJs must be above the PCBM percolation threshold in order to attain high solar cell internal quantum efficiency, and (ii) novel processing techniques, which improve polymer hole mobility while maintaining PCBM percolation within the mixed regions, should be developed in order to limit bimolecular recombination losses in optically thick devices and maximize the PCE of polymer BHJ solar cells.     

Interface Modification by Ionic Liquid: A Promising Candidate for Indoor Light Harvesting and Stability Improvement of Planar Perovskite Solar Cells

Organic–inorganic hybrid perovskite solar cells (PSCs) are currently attracting significant interest owing to their promising outdoor performance. However, the ability of indoor light harvesting of the perovskites and corresponding device performance are rarely reported. Here, the potential of planar PSCs in harvesting indoor light for low‐power consumption devices is investigated. Ionic liquid of 1‐butyl‐3‐methylimidazolium tetrafluoroborate ([BMIM]BF₄) is employed as a modification layer of [6,6]‐phenyl‐C61‐butyric acid methyl ester) (PCBM) in the inverted PSCs. The incorporation of [BMIM]BF₄ not only paves the interface contact between PCBM and electrode, but also facilitates the electron transport and extraction owing to the efficient passivation of the surface trap states. Moreover, [BMIM]BF₄ with excellent thermal stability can act as a protective layer by preventing the erosion of moisture and oxygen into the perovskite layer. The resulting devices present a record indoor power conversion efficiency (PCE) of 35.20% under fluorescent lamps of 1000 lux, and an impressive PCE of 19.30% under 1 sun illumination. The finding in this work verifies the excellent indoor performance of PSCs to meet the requirements of eco‐friendly economy.     

Efficient and Highly Air Stable Planar Inverted Perovskite Solar Cells with Reduced Graphene Oxide Doped PCBM Electron Transporting Layer

Reduced graphene oxide (rGO) is added in the [6,6]‐Phenyl‐C61‐butyric acid methyl ester (PCBM) electron transport layer (ETL) of planar inverted perovskite solar cells (PSCs), resulting in a power conversion efficiency (PCE) improvement of ≈12%, with a hysteresis‐free PCE of 14.5%, compared to 12.9% for the pristine PCBM based device. The universality of the method is demonstrated in PSCs based on CH₃NH₃PbI_3?x Cl_x and CH₃NH₃PbI₃ perovskites, deposited through one step and two step spin coating process, respectively. After a comprehensive spectroscopic characterization of both devices, it is clear that the introduction of rGO in PCBM ETL results in an important increase of the ETL conductivity, together with reduced series resistance and surface roughness. As a result, a significant photoluminescence quenching of such perovskite/ETL is observed, confirming the increased measured short circuit current density. Transient absorption measurements reveal that in the rGO‐based device, the relaxation process of the excited electrons is significantly faster compared to the reference, which implies that the charge injection rate is significantly faster for the first. Furthermore, the light soaking effect is significantly reduced. Finally, aging measurements reveal that the rGO stabilizes the ELT/perovskite interface, which results in the stabilization of perovskite crystal structure after prolonged illumination.     

Charge Transport and Recombination in Low‐Bandgap Bulk Heterojunction Solar Cell using Bis‐adduct Fullerene

Charge transport and recombination are studied for organic solar cells fabricated using blends of polymer poly[(4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐(4,7‐bis(2‐thienyl)‐2,1,3‐benzothiadiazole)‐5,5′‐diyl] (Si‐PCPDTBT) with [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (mono‐PCBM) and the bis‐adduct analogue of mono‐PCBM (bis‐PCBM). The photocurrent of Si‐PCPDTBT:bis‐PCBM devices shows a strong square root dependence on the effective applied voltage. From the relationship between the photocurrent and the light intensity, we found that the square‐root dependence of the photocurrent is governed by the mobility‐lifetime (μτ) product of charge carriers while space‐charge field effects are insignificant. The fill factor (FF) and short circuit current density (J_sc) of bis‐PCBM solar cells show a considerable increase with temperature as compared to mono‐PCBM solar cells. SCLC analysis of single carrier devices proofs that the mobility of both electrons and holes is significantly lowered when replacing mono‐PCBM with bis‐PCBM. The increased recombination in Si‐PCPDTBT:bis‐PCBM solar cells is therefore attributed to the low carrier mobilities, as the transient photovoltage measurements show that the carrier lifetime of devices are not significantly altered by using bis‐PCBM instead of mono‐PCBM.     

Spontaneous Charge Transfer and Dipole Formation at the Interface Between P3HT and PCBM

In the pursuit of developing new materials for more efficient bulk‐heterojunction solar cells, the blend poly (3‐hexylthiophene):[6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) serves as an important model system. The success of the P3HT:PCBM blend comes from efficient charge generation and transport with low recombination. There is not, however, a good microscopic picture of what causes these, hindering the development of new material systems. In this report UV photoelectron spectroscopy measurements on both regiorandom‐ (rra) and regioregular‐ (rr) P3HT are presented, and the results are interpreted using the Integer Charge Transfer model. The results suggest that spontaneous charge transfer from P3HT to PCBM occurs after heat treatment of P3HT:PCBM blends. The resulting formation of an interfacial dipole creates an extra barrier at the interface explaining the reduced (non‐)geminate recombination with increased charge generation in heat treated rr‐P3HT:PCBM blends. Extensive photoinduced absorption measurements using both above‐ and below‐bandgap excitation light are presented, in good agreement with the suggested dipole formation.     

Improved Processability and Efficiency of Colloidal Quantum Dot Solar Cells Based on Organic Hole Transport Layers

High‐efficiency solid‐state‐ligand‐exchange (SSE) step‐free colloidal quantum dot photovoltaic (CQDPV) devices are developed by employing CQD ink based active layers and organic (Polythieno[3,4‐b]‐thiophene‐co‐benzodithiophene (PTB7) and poly(3‐hexylthiophene) (P3HT)) based hole transport layers (HTLs). The device using PTB7 as an HTL exhibits superior performance to that using the current leading organic HTL, P3HT, because of favorable energy levels, higher hole mobility, and facilitated interfacial charge transfer. The PTB7 based device achieves power conversion efficiency (PCE) of 9.60%, which is the highest among reported CQDPVs using organic HTLs. This result is also comparable to the PCE of an optimized device based on a thiol‐exchanged p‐type CQD, the current‐state‐of‐the‐art HTL. From the viewpoint of device processing, the fabrication of CQDPVs is achieved by direct single‐coating of CQD active layers and organic HTLs at low temperature without SSE steps. The experimental results and device simulation results in this work suggest that further engineering of organic HTL materials can open new doors to improve the performance and processing of CQDPVs.     

The Effect of Fluorination in Manipulating the Nanomorphology in PTB7:PC71BM Bulk Heterojunction Systems

The best performing low bandgap copolymers PTB series to date which is based on thieno[3,4‐b]thiophene‐alt‐benzodithiophene units blended with [6,6]‐phenyl‐C71‐butyric acid methyl ester (PC₇₁BM), have been the focus of polymer‐based solar cells. Here, novel fluorinated polymers PTB7‐Fx (fluorine units coupled with submonomer thieno[3,4‐b]thiophene) with varied degree of fluorination are used as electron donor materials. The PTB7‐Fx:PC₇₁BM bulk heterojunction (BHJ) films spin‐coated from the host solvent chlorobenzene without and with solvent additive 1,8‐diiodooctane (DIO) and the corresponding solar cell devices are systematically investigated to address the morphology‐efficiency relationship. Self‐assembled BHJ morphology is already observed for as‐spun blend films. After adding the solvent additive DIO, the pronounced ordered structures are suppressed and better intermixed films with much smaller domain sizes result. Full fluorination of the third C‐atom of thienothiophene gives rise to the highest power conversion efficiency. As the absorption properties, film morphology and crystallinity remain similar for different degrees of fluorination, the main influence of the photovoltaic performance is ascribed to the different lowest unoccupied molecular orbital (LUMO) of each polymer instead of the film morphology. Thus the device performance can be efficiently improved by tuning the energy level of the polymer without necessarily changing either the film nanomorphology or crystallinity dramatically.     

The Effect of PCBM Dimerization on the Performance of Bulk Heterojunction Solar Cells

Increasing the lifetime of polymer based organic solar cells is still a major challenge. Here, the photostability of bulk heterojunction solar cells based on the polymer poly[4,4′‐bis(2‐ethylhexyl)dithieno[3,2‐b:2′,3′‐d]silole)‐2,6‐diyl‐alt‐[2,5‐bis(3‐tetradecylthiophen‐2‐yl)thiazole[5,4‐d]thiazole)‐1,8‐diyl] (PDTSTzTz) and the fullerene [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PC₆₀BM) under inert atmosphere is investigated. Correlation of electrical measurements on complete devices and UV‐vis absorption measurements as well as high‐performance liquid chromatography (HPLC) analysis on the active materials reveals that photodimerization of PC₆₀BM is responsible for the observed degradation. Simulation of the electrical device parameters shows that this dimerization results in a significant reduction of the charge carrier mobility. Both the dimerization and the associated device performance loss turn out to be reversible upon annealing. BisPC₆₀BM, the bis‐substituted analog of PC₆₀BM, is shown to be resistant towards light exposure, which in turn enables the manufacture of photostable PDTSTzTz:bisPC₆₀BM solar cells.     

Nanofiber‐Based Bulk‐Heterojunction Organic Solar Cells Using Coaxial Electrospinning

Nanofibers consisting of the bulk heterojunction organic photovoltaic (BHJ–OPV) electron donor–electron acceptor pair poly(3‐hexylthiophene):phenyl‐C₆₁‐butyric acid methyl ester (P3HT:PCBM) are produced through a coaxial electrospinning process. While P3HT:PCBM blends are not directly electrospinnable, P3HT:PCBM‐containing fibers are produced in a coaxial fashion by utilizing polycaprolactone (PCL) as an electrospinnable sheath material. Pure P3HT:PCBM fibers are easily obtained after electrospinning by selectively removing the PCL sheath with cyclopentanone (average diameter 120 ± 30 nm). These fibers are then incorporated into the active layer of a BHJ–OPV device, which results in improved short‐circuit current densities, fill factors, and power‐conversion efficiencies (PCE) as compared to thin‐film devices of identical chemical composition. The best‐performing fiber‐based devices exhibit a PCE of 4.0%, while the best thin‐film devices have a PCE of 3.2%. This increase in device performance is attributed to the increased in‐plane alignment of P3HT polymer chains on the nanoscale, caused by the electrospun fibers, which leads to increased optical absorption and subsequent exciton generation. This methodology for improving device performance of BHJ–OPVs could also be implemented for other electron donor–electron acceptor systems, as nanofiber formation is largely independent of the PV material.     

Perylene Sensitization of Fullerenes for Improved Performance in Organic Photovoltaics

We present the addition of an energy relay dye to fullerenes resulting in increased light harvesting and significantly improved power conversion efficiency for organic photovoltaic (OPV) devices. Although exhibiting excellent properties as electron acceptors, visible light absorption of fullerenes is limited. Strongly light absorbing donor materials are needed for efficient light harvesting in the thin active layer of OPV devices. Therefore, photocurrent generation and thus power conversion efficiency of this type of solar cell is confined by the overlap of the relatively narrow absorption band of commonly used donor molecules with the solar spectrum. Herein the concept of fullerene dye sensitization is presented, which allows increased light harvesting on the electron acceptor side of the heterojunction. The concept is exemplarily shown for an UV absorbing small molecule and a near infrared absorbing polymer, namely hexa‐peri‐hexabenzocoronene (HBC) and Poly[2,1,3‐benzothiadiazole‐4,7‐diyl[4,4‐bis(2‐ethylhexyl)‐4H‐cyclopenta[2,1‐b:3,4‐b']dithiophene‐2,6‐diyl]] (PCPDTBT), respectively. In both systems remarkably higher power conversion efficiency is achieved via perylene sensitization of the fullerene acceptor. Steady state photoluminescence, transient absorption and transient photocurrent decay studies reveal pathways of the additionally generated excited states at the sensitizer molecule. The findings suggest fluorescence resonance energy transfer from the photo‐excited dye to the fullerene enabling decoupling of light absorption and charge transport. The presented sensitization method is proposed as a viable new concept for performance enhancement in organic photovoltaic devices.     

Favorable Mixing Thermodynamics in Ternary Polymer Blends for Realizing High Efficiency Plastic Solar Cells

Ternary blends with broad spectral absorption have the potential to increase charge generation in organic solar cells but feature additional complexity due to limited intermixing and electronic mismatch. Here, a model system comprising the polymers poly[5,5‐bis(2‐butyloctyl)‐(2,2‐bithiophene)‐4,4‐dicarboxylate‐alt‐5,5‐2,2‐bithiophene] (PDCBT) and PTB7‐Th and PC₇₀BM as an electron accepting unit is presented. The power conversion efficiency (PCE) of the ternary system clearly surpasses the performance of either of the binary systems. The photophysics is governed by a fast energy transfer process from PDCBT to PTB7‐Th, followed by electron transfer at the PTB7‐Th:fullerene interface. The morphological motif in the ternary blend is characterized by polymer fibers. Based on a combination of photophysical analysis, GIWAXS measurements and calculation of the intermolecular parameter, the latter indicating a very favorable molecular affinity between PDCBT and PTB7‐Th, it is proposed that an efficient charge generation mechanism is possible because PTB7‐Th predominantly orients around PDCBT filaments, allowing energy to be effectively relayed from PDCBT to PTB7‐Th. Fullerene can be replaced by a nonfullerene acceptor without sacrifices in charge generation, achieving a PCE above 11%. These results support the idea that thermodynamic mixing and energetics of the polymer–polymer interface are critical design parameter for realizing highly efficient ternary solar cells with variable electron acceptors.     

Plasmonic Back Reflectors: A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

A Small Molecule Non‐fullerene Electron Acceptor for Organic Solar Cells

Organic bulk heterojunction photovoltaic devices predominantly use the fullerene derivatives [C60]PCBM and [C70]PCBM as the electron accepting component. This report presents a new organic electron accepting small molecule 2‐[{7‐(9,9‐di‐n‐propyl‐9H‐fluoren‐2‐yl)benzo[c][1,2,5]thiadiazol‐4‐yl}methylene]malononitrile (K12) for organic solar cell applications. It can be processed by evaporation under vacuum or by solution processing to give amorphous thin films and can be annealed at a modest temperature to give films with much greater order and enhanced charge transport properties. The molecule can efficiently quench the photoluminescence of the donor polymer poly(3‐n‐hexylthiophene‐2,5‐diyl) (P3HT) and time resolved microwave conductivity measurements show that mobile charges are generated indicating that a truly charge separated state is formed. The power conversion efficiencies of the photovoltaic devices are found to depend strongly on the acceptor packing. Optimized K12:P3HT bulk heterojunction devices have efficiencies of 0.73±0.01% under AM1.5G simulated sunlight. The efficiencies of the devices are limited by the level of crystallinity and nanoscale morphology that was achievable in the blend with P3HT.     

Terthieno[3,2‐b]Thiophene (6T) Based Low Bandgap Fused‐Ring Electron Acceptor for Highly Efficient Solar Cells with a High Short‐Circuit Current Density and Low Open‐Circuit Voltage Loss

A terthieno[3,2‐b]thiophene ( 6T ) based fused‐ring low bandgap electron acceptor, 6TIC , is designed and synthesized for highly efficient nonfullerene solar cells. The chemical, optical, and physical properties, device characteristics, and film morphology of 6TIC are intensively studied. 6TIC shows a narrow bandgap with band edge reaching 905 nm due to the electron‐rich π‐conjugated 6T core and reduced resonance stabilization energy. The rigid, π‐conjugated 6T also offers lower reorganization energy to facilitate very low V_OC loss in the 6TIC system. The analysis of film morphology shows that PTB7‐Th and 6TIC can form crystalline domains and a bicontinuous network. These domains are enlarged when thermal annealing is applied. Consequently, the device based on PTB7‐Th : 6TIC exhibits a high power conversion efficiency (PCE) of 11.07% with a high J_SC > 20 mA cm^?2 and a high V_OC of 0.83 V with a relatively low V_OC loss (≈0.55 V). Moreover, a semitransparent solar cell based on PTB7‐Th : 6TIC exhibits a relatively high PCE (7.62%). The device can have combined high PCE and high J_SC is quite rare for organic solar cells.