Continuous ethanol production by immobilized yeast reactor coupled with membrane pervaporation unit

A system comprised of an immobilized yeast reactor producing ethanol, with a membrane pervaporation module for continuously removing and concentrating the produced ethanol, was developed. The combined system consisted of two integrated circulation loops: In one the sugar-containing medium is circulated through the membrane pervaporation module. The two loops were interconnected in a way allowing for separate parameter optimization (e.g., flow rate, temperature, pH) for each loop.The fermentation unit was 2.0 L bioreactor with five equal segments, packed with 5-mm beads of immobilized yeasts. The bead matrix was a crosslinked polyacrylamide hydrazide gel coated with calcium alginate. The fast circulation loop of the bioreactor allowed for efficient liberation of CO(2) at the top of the immobilized yeast reactor. Continuous operation of the uncoupled reactor for over 50 days with inflowing defined medium or dilute molasses at a residence time of 1.25 h yielded ethanol at a rate of about 10 g/L h.The pervaporation unit was constructed from four 60-cm-long tubular membranes of silicone composite on a polysulfone support. The output from the fermentor was circulated through the inside of the tubes of a unit with a total surface area of 800 cm(2), having an average flux of 150 mL/h, and selectivities to ethanol vs. water up to 7. A vacuum of 30 mb was applied to the outside of the tubes, removing 20-30 g of ethanol per hour, which was collected in condensors. The continuous removal of ethanol, avoiding inhibition of the fermentation process, resulted in an improved productivity and allowed the use of high sugar concentrations (40% wt/vol) offering the potential of a compact system with reduced stillage.The combined system of ethanol production and removal enabled an operative steady state at which the liquid volume of the system, and the concentrations of ethanol within the reactor ( 4% wt/vol), as well as within the flux crossing the pervaporation membrane (17%-20% wt/vol) were kept constant. At the steady state, a 40% wt/vol sugar solution could be continuously added to the fermentor when 12%-20% wt/vol clear ethanol solution was continuously removed by the pervaporation unit. Membrane fouling was reversed by short washing steps, and continuous step operation was maintained by working with two different modules that were interchanged. In this manner, long term continuous operation (over 40 days) was achieved with a productivity of 20-30 g/L h, representing over a twofold increase relative to the continuously operated reactor uncoupled from the membrane and a fivefold increase in comparison with the value obtained fro a corresponding batch fermentation.     

Ethanol production in a continuous fermentation/membrane pervaporation system

The productivity of ethanol fermentation processes, predominantly based on batch operation in the U.S. fuel ethanol industry, could be improved by adoption of continuous processing technology. In this study, a conventional yeast fermentation was coupled to a flat-plate membrane pervaporation unit to recover continuously an enriched ethanol stream from the fermentation broth. The process employed a concentrated dextrose feed stream controlled by the flow rate of permeate from the pervaporation unit via liquid-level control in the fermentor. The pervaporation module contained 0.1 m² commercially available polydimethylsiloxane membrane and consistently produced a permeate of 20%–23% (w/w) ethanol while maintaining a level of 4%–6% ethanol in a stirred-tank fermentor. The system exhibited excellent operational stability. During continuous operation with cell densities of 15–23 g/l, ethanol productivities of 4.9–7.8 gl^–1 h^–1 were achieved utilizing feed streams of 269–619 g/l glucose. Pervaporation flux and ethanol selectivities were 0.31–0.79 lm^–2 h^–1 and 1.8–6.5 respectively.     

Ethanol fermentation coupled with complete cell recycle pervaporation system: Dependence of glucose concentration

Summary A membrane bioreactor system comprised of a fermenter and a flat pervaporation module was developed for continuous ethanol fermentation by Saccharomyces cerevisiae. In order to obtain the guidelines for high sugar concentration fermentation, the dependence of glucose concentration on the coupled system was investigated. Fed by 158 and 290g glucose/l, the improvement in productivity was obtained with 1. 58 and 1. 86 times, and the ethanol yield was 0. 45 and 0. 395, respectively. With the fermentation proceeding, the permeate flux decreased but the selectivity kept unaltered.     

Ethanol production in an integrated process of fermentation and ethanol recovery by pervaporation

In ethanol fermentations inhibition of the microorganism by ethanol limits the amount of substrate in the feed that can be converted. In a process high feed concentrations are desirable to minimize the flows. Such high feed concentrations can be realized in integrated processes in which ethanol is recovered from the fermentation broth as it is formed. In this study ethanol recovery by pervaporation was coupled to glucose fermentations by baker's yeast. Pervaporation was carried out with commercial silicone based hollow-fibre membrane modules with relatively high fluxes. Three different types of process configurations with pervaporation were investigated. Two of these configurations also included cell retention by microfiltration, in order to optimize the productivity. In the systems with pervaporation a feed containing 360 kg/m³ glucose could be converted almost completely. This feed concentration is a factor three higher than in a process without ethanol recovery. The productivity was 14 kg/m³ h in a system with pervaporation only, and could be increased to 43 kg/m³ h in the system with all recycle by microfiltration. The kinetic data suggest that accumulation of inhibitory compounds occurs in the integrated system. The integrated process was relatively easy in operation.     

Production of 2-phenylethanol and 2-phenylethylacetate from L-phenylalanine by coupling whole-cell biocatalysis with organophilic pervaporation

An integrated bioprocess for the production of the natural rose-like aroma compounds, 2-phenylethanol (2-PE) and 2-phenylethylacetate (2-PEAc), from L-phenylalanine (L-phe) with yeasts was investigated. The hydrophobicity of the products leads to product inhibition, which can be compensated by in situ product removal (ISPR). An organophilic pervaporation unit, equipped with a polyoctylmethylsiloxane (POMS) membrane, was coupled via a bypass to a bioreactor and proved to be a suitable technique for the in situ removal of high-boiling products from culture broth. With batch cultures of the thermotolerant yeast Kluyveromyces marxianus CBS 600 in a standard medium at 35 degrees C, the use of pervaporation resulted in a double 2-PE concentration (2.2 g/L) and 1.3 g/L 2-PEAc, which only accumulated transiently in low concentrations during cultivation without ISPR. Using a previously optimized medium, the variation of the temperature from 30 degrees C to 40 degrees C caused an increase in the total conversion yield from 63% to 79%, corresponding to total product concentrations of 5.23 and 5.85 g/L, respectively. In the 40 degrees C batch experiment, the volumetric productivity (2-PE + 2-PEAc) during the exponential phase was 5.2 mmol/L h. While for 2-PE, there is still potential for further optimization, the more hydrophobic 2-PEAc was nearly completely removed from the aqueous culture broth (enrichment factor >400), resulting in highly aroma-enriched permeates. Due to the temperature-correlated performance of the pervaporation, the bioconversion was still efficient even at 45 degrees C (conversion yield: 69%). Surprisingly, at 45 degrees C, the molar ratio of the two products inverted and 2-PEAc turned out to be the main product (4.0 g/L), which opens easy control of the reaction's selectivity by external means. Retrofitting the process with interim heating and cooling equipment to use different temperature levels for cultivation and pervaporation resulted in a decreased yield and product concentration caused by multiple stress factors. The medium composition affected the pervaporation efficiency with molasses acting detrimental.     

Ethanol extraction by supported liquid membrane during fermentation

A supported liquid membrane system was developed for the extraction of ethanol during semicontinuous fermentation of Saccharomyces bayanus. it consisted of a porous Teflon sheet as support, soaked with isotridecanol. This assembly permitted combining biocompatibility, permeation efficiency, and stability. The removal of ethanol from the cultures led to decreased inhibition and, thus, to a gain in conversion of 452 g/L glucose versus 293 g/L glucose without extraction. At the same time, the ethanol volumetric productivity was enhanced 2.5 times, due to an improvement of yeast viability, while the substrate conversion yield was maintained above 95% of its theoretical value. Besides these improvements in fermentation performances, the process resulted in ethanol purification, since the separation was selective towards microbial cells and carbon substrate, and likely selective to mineral ions present in the fermentation broth. For pervaporation, a concentration of ethanol four times greater was obtained in the collected permeate.     

Production of ethanol in repeated-batch fermentation with membrane-type bioreactor

The average ethanol content in sake is 14 wt%; continuous production of such a high ethanol content was found not to be stably maintained in a packed-bed bioreactor with immobilized yeast cells, used normally for production of an ethanol content of up to 10 wt%. However, use of repeated-batch ethanol fermentation incorporating a membrane filter for product separation enabled a high ethanol content and improved productivity to be achieved. In this bioreactor, the yeast cells were retained within the bioreactor and a high yeast concentration was possible. A filtrate containing 14 wt% ethanol was obtained steadily after each batchwise operation. At a yeast concentration of 110 g/l, an ethanol productivity of 3.5 g/l/h was attained, which is 9 times higher than that in conventional batch fermentation. A mathematical model is proposed for assessment of the repeated-batch fermentation process. The estimated results agreed well with the observed ones. With a view to the application of this system to sake production, the aroma components of the filtrate were assayed and compared with those of a commercial-grade sake.     

Scale up of fuel ethanol production from sugar beet juice using loofa sponge immobilized bioreactor

Production of fuel ethanol from sugar beet juice, using cells immobilized on loofa sponge was investigated. Based on ethanol productivity and ease of cell immobilization, a flocculating yeast strain, Saccharomyces cerevisiae IR2 was selected for ethanol production from sugar beet juice. It was found that raw sugar beet juice was an optimal substrate for ethanol production, requiring neither pH adjustment nor nitrogen source supplement. When compared with a 2 l bubble column bioreactor, mixing was not sufficient in an 8 l bioreactor containing a bed of sliced loofa sponges and consequently, the immobilized cells were not uniformly distributed within the bed. Most of the cells were immobilized in the lower part of the bed and this resulted in decreased ethanol productivity. By using an external loop bioreactor, constructing the fixed bed with cylindrical loofa sponges, dividing the bed into upper, middle and lower sections with approximately 1 cm spaces between them and circulating the broth through the loop during the immobilization, uniform cell distribution within the bed was achieved. Using this method, the system was scaled up to 50 l and when compared with the 2 l bubble column bioreactor, there were no significant differences (P > 0.05) in ethanol productivity and yield. By using external loop bioreactor to immobilize the cells uniformly on the loofa sponge beds, efficient large scale ethanol production systems can be constructed.     

Simultaneous amylase production,raw cassava starch hydrolysis and ethanol production by immobilized Aspergillus awamori and Saccharomyces cerevisiae in a novel alternating liquid phase–air phase system

As a solution to the problems of mass transfer limitation in submerged cultures and scale up of solid-state/liquid-surface cultures, an alternating liquid phase–air phase bioreactor was developed. It consisted of a bioreactor equipped with a siphon system and a reservoir. Aspergillus awamori was immobilized in loofa sponge inside the bioreactor and culture broth was pumped from the reservoir into the bioreactor. Each time the culture broth level reached a critical level, the broth automatically siphoned back into the reservoir. Thus the immobilized cells were alternatingly submerged and exposed to air. The duration of each phase was controlled by the pumping rate and with an on-off timer. During amylase production from soluble starch and raw cassava starch, the optima ratios of the liquid to air phases were 12 h : 12 h and 3 h : 6 h respectively. Saccharomyces cerevisiae IR2 was immobilized in the reservoir and the system was used for simultaneous amylase production, hydrolysis and ethanol production from raw cassava starch. The process was very stable for more than 7 batches with high ethanol yield of 0.46 g-ethanol/g-starch and productivity of 1.73 g-ethanol/L/h. These values are high, the system can be scaled up, and thus it has many potential applications.     

Application of a membrane recycle bioreactor for continuous ethanol production

Summary A series of continuous fermentations were carried out with a production strain of the yeast Saccharomyces cerevisiae in a membrane bioreactor. A membrane separation module composed of ultrafiltration tubular membranes retained all biomass in a fermentation zone of the bioreactor and allowed continuous removal of fermentation products into a cell-free permeate. In a system with total (100%) cell recycle the impact of fermentation conditions [dilution rate (0.03–0.3 h^–1); substrate concentration in the feed (50–300 g·1^–1); biomass concentration (depending on the experimental conditions)] was studied on the behaviour of the immobilized cell population and on ethanol formation. Maximum ethanol productivity (15 g·1^–1·h^–1) was attained at an ethanol concentration of 81 g·1^–1. The highest demands of cells for maintenance energy were found at the maximum feed substrate concentration (300 g·1^–1) and at very low concentrations of cells in the broth.     

Continuous butanol/isopropanol fermentation in down-flow column reactor coupled with pervaporation using supported liquid membrane

Continuous butanol/isopropanol fermentation with immobilized Clostridium isopropylicum was performed in a downflow column reactor using molasses as the substrate. In order to prevent product inhibition and at the same time obtain high concentration of the products, the column reactor was coupled with a pervaporation module using a supported liquid membrane. The liquid membrane was prepared with oleyl alcohol nontoxic to the microorganism. In comparison with the continuous fermentation without product removal, the specific butanol production rate was 2 times higher. The butanol concentration in the permeate was 230 kg/m(3), which was about 50 times higher than that in the culture broth. A numerical investigation suggested a further increase in the productivity by improving the module construction.     

High ethanol productivities using small Ca-alginate beads of immobilized cells of Zymomonas mobilis

Summary Zymomonas mobilis cells were immobilized into small 1 mm diameter beads of Ca-alginate in order to minimize mass transfer limitations and maximize immobilized cell activity. A combination of small bead size with a high cell concentration of 58 g dry wt. cell per lit. bead volume resulted in high ethanol productivities using a newly designed packed bed bioreactor system. Steady-state dilution rates ranging from 0.4 h^-1 to 3.9 h^-1 were run resulting in a maximum productivity of 102 g ethanol/l/h for an inlet substrate concentration of 100 g glu/l and 87% conversion. The bioreactor was run continuously at a fixed dilution rate for 384 h and short intermittent treatment of the beads with CaCl₂ temporarily increased ethanol productivity to a maximum of 116 g ethanol/l/h.     

Optimization of process parameters for the continuous ethanol production by Kluyveromyces lactis immobilized cells in hydrogel copolymer carrier

In the present study the optimized parameters for highest ethanol productivity by Kluyveromyces lactis immobilized cells bioreactor were obtained using the method of Lagrange multipliers. Immobilized growing yeast cells in PVA: HEMA (7%: 10%, w/w) hydrogel copolymer carrier produced by radiation polymerization were used in a packed-bed column reactor for the continuous production of ethanol from lactose at different levels of concentrations (50, 100 and 150) gL(-1). The results indicate that volumetric ethanol productivity is influenced by substrate concentration and dilution rate. The highest value 7.17 gL(-1) h(-1) is obtained at higher lactose concentration (150 gL(-1)) in feed medium and 0.3 h(-1) dilution rate. The same results have been obtained through the application of "LINGO" software for mathematical optimization.     

Long-Term Continuous Cultivation of Clostridium beijerinckii in a Two-Stage Chemostat with On-Line Solvent Removal

A two-stage continuous cultivation experiment with Clostridium beijerinckii NRRL B592 is described. This strain maintained its ability to produce neutral solvents (acetone, n-butanol, and ethanol) at an overall dilution rate of 0.13 h(sup-1) and achieved an average overall solvent concentration of 9.27 g/liter and an overall solvent productivity of 1.24 g/liter/h for more than 100 overall retention times. The experiment was performed without pH control on a semisynthetic medium containing yeast extract, and product inhibition was the limiting factor. Solid carrier material was present in both stages, and the solvent productivity in both stages was similar. A membrane evaporation module integrated into the recirculation loop of a second-stage bioreactor after 2,166 h increased solvent productivity and improved the yield of solvents by about 40%. The membrane reduced the concentration of solvents, which would otherwise inhibit the fermentation. Additionally, the integrated membrane evaporation dampened metabolic oscillations, which are characteristic of continuous cultivation of clostridia. It was also demonstrated that a moderate concentration buildup (approximately 30% of bioreactor inflow) caused by water flux through the membrane caused no detrimental effects to the bacterial cells. However, much higher water fluxes through the membrane, associated with a much more dramatic increase in the concentration of salts in the medium, did appear to favor cell degeneration.     

Production of L(+)-lactic acid from glucose and starch by immobilized cells of Rhizopus oryzae in a rotating fibrous bed bioreactor

A rotating fibrous-bed bioreactor (RFB) was developed for fermentation to produce L(+)-lactic acid from glucose and cornstarch by Rhizopus oryzae. Fungal mycelia were immobilized on cotton cloth in the RFB for a prolonged period to study the fermentation kinetics and process stability. The pH and dissolved oxygen concentration (DO) were found to have significant effects on lactic acid productivity and yield, with pH 6 and 90% DO being the optimal conditions. A high lactic acid yield of 90% (w/w) and productivity of 2.5 g/L.h (467 g/h.m(2)) was obtained from glucose in fed-batch fermentation. When cornstarch was used as the substrate, the lactic acid yield was close to 100% (w/w) and the productivity was 1.65 g/L.h (300 g/h.m(2)). The highest concentration of lactic acid achieved in these fed-batch fermentations was 127 g/L. The immobilized-cells fermentation in the RFB gave a virtually cell-free fermentation broth and provided many advantages over conventional fermentation processes, especially those with freely suspended fungal cells. Without immobilization with the cotton cloth, mycelia grew everywhere in the fermentor and caused serious problems in reactor control and operation and consequently the fermentation was poor in lactic acid production. Oxygen transfer in the RFB was also studied and the volumetric oxygen transfer coefficients under various aeration and agitation conditions were determined and then used to estimate the oxygen transfer rate and uptake rate during the fermentation. The results showed that the oxygen uptake rate increased with increasing DO, indicating that oxygen transfer was limited by the diffusion inside the mycelial layer.     

High cell density ethanol fermentation in an upflow packed-bed cell recycle bioreactor

An upflow packed-bed cell recycle bioreactor (IUPCRB) is proposed for obtaining a high cell density. The system is comprised of a stirred tank bioreactor in which cells are retained partially by a packed-bed. A 1.3 cm (ID) × 48 cm long packed-bed was installed inside a 2 L bioreactor (working volume 1 L). Continuous ethanol fermentation was carried out using a 100 g/L glucose solution containing Saccharomyces cerevisiae (ATCC 24858). Cell retention characteristics were investigated by varying the void fraction (VF) of the packed bed by packing it with particles of 0.8∼2.0 mm sized stone, cut hollow fiber pieces, ceramic, and activated carbon particles. The best results were obtained using an activated carbon bed with a VF of 30∼35%. The IUPCRB yielded a maximum cell density of 87 g/L, an ethanol concentration of 42 g/L, and a productivity of 21 g/L/h when a 0.5 h⁻¹ dilution rate was used. A natural bleeding of cells from the filter bed occurred intermittently. This cell loss consisted of an average of 5% of the cell concentration in the bioreactor when a high cell concentration (approximately 80 g/L) was being maintained.     

Extractive fermentation for butyric acid production from glucose by Clostridium tyrobutyricum

A novel extractive fermentation for butyric acid production from glucose, using immobilized cells of Clostridium tyrobutyricum in a fibrous bed bioreactor, was developed by using 10% (v/v) Alamine 336 in oleyl alcohol as the extractant contained in a hollow-fiber membrane extractor for selective removal of butyric acid from the fermentation broth. The extractant was simultaneously regenerated by stripping with NaOH in a second membrane extractor. The fermentation pH was self-regulated by a balance between acid production and removal by extraction, and was kept at approximately pH 5.5 throughout the study. Compared with conventional fermentation, extractive fermentation resulted in a much higher product concentration (>300 g/L) and product purity (91%). It also resulted in higher reactor productivity (7.37 g/L. h) and butyric acid yield (0.45 g/g). Without on-line extraction to remove the acid products, at the optimal pH of 6.0, the final butyric acid concentration was only approximately 43.4 g/L, butyric acid yield was 0.423 g/g, and reactor productivity was 6.77 g/L. h. These values were much lower at pH 5.5: 20.4 g/L, 0.38 g/g, and 5.11 g/L. h, respectively. The improved performance for extractive fermentation can be attributed to the reduced product inhibition by selective removal of butyric acid from the fermentation broth. The solvent was found to be toxic to free cells in suspension, but not harmful to cells immobilized in the fibrous bed. The process was stable and provided consistent long-term performance for the entire 2-week period of study.     

Effects of by-products of fermentation of banana pseudostem on ethanol separation by pervaporation

In this work, we performed recovery of ethanol from a fermentation broth of banana pseudostem by pervaporation (PV) as a lower-energy-cost alternative to traditional separation processes such as distillation. As real fermentation systems generally contain by-products, it was investigated the effects of different components from the fermentation broth of banana pseudostem on PV performance for ethanol recovery through commercial flat sheet polydimethylsiloxane (PDMS) membrane. The experiments were compared to a binary solution (ethanol/water) to determine differences in the results due to the presence of fermentation by-products. A real fermented broth of banana pseudostem was also used as feed for the PV experiments. Seven by-products from fermented broth were identified: propanol, isobutanol, methanol, isoamyl alcohol, 1-pentanol, acetic acid, and succinic acid. Moreover, the residual sugar content of 3.02 g/L¹ was obtained. The presence of methanol showed the best results for total permeate flux (0.1626 kg·m⁻²·h⁻¹) and ethanol permeate flux (0.0391 kg·m⁻²·h⁻¹) during PV at 25°C and 3 wt% ethanol, also demonstrated by the selectivity and enrichment factor. The lowest total fluxes of permeate were observed in the experiments containing the acids. Better permeance of 0.1171 from 0.0796 kg·m⁻²·h⁻¹ and membrane selectivity of 9.77 from 9.30 were obtained with real fermentation broth than with synthetic solutions, possibly due to the presence of by-products in the multicomponent mixtures, which contributed to ethanol permeation. The results of this work indicate that by-products influence pervaporation of ethanol with hydrophobic flat sheet membrane produced from the fermented broth of banana pseudostem.     

Ethanol fermentation of raw cassava starch with Rhizopus koji in a gas circulation type fermentor

Studies have been conducted in a gas circulation type fermentor in order to characterize the ethanol fermentation of uncooked cassava starch with Rhizopus koji. Results showed that ethanol concentration reached 13-14% (v/v) in 4-day broth, and the maximum productivity of ethanol was 2.3 g ethanol/L broth h. This productivity was about 50% compared to the productivity of a glucose-yeast system. Ethanol yield reached 83.5-72.3% of the theoretical yield for the cassava starch used. The fermentor used in the present work has been proven by experiment to be suitable for ethanol fermentation of the broth with solid substrate.     

Acetone–butanol–ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 and in situ recovery by PDMS/ceramic composite membrane

PDMS/ceramic composite membrane was directly integrated with acetone-butanol-ethanol (ABE) fermentation using Clostridium acetobutylicum XY16 at 37 °C and in situ removing ABE from fermentation broth. The membrane was integrated with batch fermentation, and approximately 46 % solvent was extracted. The solvent in permeates was 118 g/L, and solvent productivity was 0.303 g/(L/h), which was approximately 33 % higher compared with the batch fermentation without in situ recovery. The fed-batch fermentation with in situ recovery by pervaporation continued for more than 200 h, 61 % solvent was extracted, and the solvent in penetration was 96.2 g/L. The total flux ranged from 0.338 to 0.847 kg/(m(2)/h) and the separation factor of butanol ranged from 5.1 to 27.1 in this process. The membrane was fouled by the active fermentation broth, nevertheless the separation performances were partially recovered by offline membrane cleaning, and the solvent productivity was increased to 0.252 g/(L/h), which was 19 % higher compared with that in situ recovery process without membrane cleaning.