The BARC biosensor applied to the detection of biological warfare agents

The Bead ARray Counter (BARC) is a multi-analyte biosensor that uses DNA hybridization, magnetic microbeads, and giant magnetoresistive (GMR) sensors to detect and identify biological warfare agents. The current prototype is a table-top instrument consisting of a microfabricated chip (solid substrate) with an array of GMR sensors, a chip carrier board with electronics for lock-in detection, a fluidics cell and cartridge, and an electromagnet. DNA probes are patterned onto the solid substrate chip directly above the GMR sensors, and sample analyte containing complementary DNA hybridizes with the probes on the surface. Labeled, micron-sized magnetic beads are then injected that specifically bind to the sample DNA. A magnetic field is applied, removing any beads that are not specifically bound to the surface. The beads remaining on the surface are detected by the GMR sensors, and the intensity and location of the signal indicate the concentration and identity of pathogens present in the sample. The current BARC chip contains a 64-element sensor array, however, with recent advances in magnetoresistive technology, chips with millions of these GMR sensors will soon be commercially available, allowing simultaneous detection of thousands of analytes. Because each GMR sensor is capable of detecting a single magnetic bead, in theory, the BARC biosensor should be able to detect the presence of a single analyte molecule.     

Comparison of a prototype magnetoresistive biosensor to standard fluorescent DNA detection

We present a comparative analysis of a magnetoresistive biosensor to standard fluorescent DNA detection. The biosensor consists of giant magnetoresistive (GMR) type Cu/Ni(80)Fe(20) multilayers in the second antiferromagnetic coupling maximum. Each of the 206 elements of the magnetoresistive biosensor is patterned into a spiral-shaped line that can cover the area of a typical DNA spot (70 microm diameter). The probe DNA is assembled on top of the sensor elements in different concentrations ranging from 16 pg/microl to 10 ng/microl. Complementary biotin-labeled analyte DNA is hybridized to the probe DNA at a concentration of 10 ng/microl. A number of different commercially available magnetic microspheres are investigated to determine the most appropriate markers. The experimental comparison shows that the relative sensitivity of the magnetoresistive biosensor is superior to the fluorescent detection at low probe DNA concentrations.     

A DNA sequence-specific electrochemical biosensor based on alginic acid-coated cobalt magnetic beads for the detection of E. coli

A new type of DNA sequence-specific electrochemical biosensor based on magnetic beads for the detection of Escherichia coli is reported in the present work. Alginic acid-coated cobalt magnetic beads, capped with 5'-(NH(2)) oligonucleotide and employed not only for magnetic separation but also as the solid adsorbent, were used as DNA probes to hybridize with the target E. coli DNA sequence. This assay was specific for E. coli detection depending on the uid A gene, which encodes for the enzyme β-d-glucuronidase produced by E. coli strains. When daunomycin (DNR) was used as DNA hybridization indicator, the target sequences of E. coli hybridized with the probes resulted in the decrease of DNR reduction peak current, which was proportional to the E. coli concentration. The optimization of the hybridization detection was carried out and the specificity of the probes was also demonstrated. This DNA biosensor can be employed to detect a complementary target sequence for 3.0×10(-10) mol/L and denatured PCR products for 0.5 ng/μL. The linear range of the developed biosensor for the detection of E. coli cells was from 1.0×10(2) to 2.0×10(3) cells/mL with a detection limit of 50 cells/mL. After a brief enrichment process, a concentration of 10 cells/mL E. coli in real water samples was detected by the electrochemical biosensor.     

Magnetic bead hybridization to detect enterotoxigenic Escherichia coli strains associated with cattle in environmental water sources

A magnetic capture hybridization - polymerase chain reaction (MCH-PCR) method was used to increase the detection sensitivity of the enterotoxin gene LTIIa, used as a biomarker for waste in environmental samples. The samples were collected from cow lagoons of different farms and from environmental waters. Total DNA was extracted from colonies grown on mTEC medium or directly from environmental samples. The cow-specific Escherichia coli LTIIa gene was used as a DNA marker. A LTIIa-specific oligonucleotide probe was designed to capture the LTIIa marker during the MCH, followed by PCR. Varying levels of humic acid were added to the DNA extracts to evaluate the sensitivity and effectiveness of MCH-PCR. The minimal detection limit of MCH-PCR for the LTIIa gene was 2.5 ag/muL DNA. In the presence of humic acid, MCH-PCR was able to increase the detection sensitivity 10 000-fold over that of conventional PCR. The MCH-PCR could also detect one cell with the LTIIa DNA marker in a 1-L seeded environmental water sample. Results in this study indicate that MCH-PCR is more sensitive than nested PCR in testing environmental samples.     

Analysing a magnetic molecule detection system--computer simulation

The detection of single molecules, e.g. in biology is possible by marking the interesting molecules with magnetic beads and detect the influence of the beads on giant magnetoresistance (GMR)/tunnel magnetoresistance (TMR)/spin valve (SV) sensors. The development of suitable multilayers has been studied experimentally as well as theoretically in order to optimize the sensor parameters. A finite difference (FD) method including the usually used contributions to the total energy [exchange, antiferromagnetically (af) coupling, anisotropy and magnetostatic] is used for the simulation with additional contributions to the local field according to the stray fields of the beads. In this work, we will show the results of micromagnetic calculations of the magnetization behavior of GMR/TMR sensors considering also the interaction between the domains in the magnetic layers of the sensor and the bead area. We can present first calculations where the bead particles (signal source) and the magnetic layers (sensor device) are considered as a whole magnetic ensemble.     

Microscale detection of specific bacterial DNA in soil with a magnetic capture-hybridization and PCR amplification assay.

A magnetic capture-hybridization PCR technique (MCH-PCR) was developed to eliminate the inhibitory effect of humic acids and other contaminants in PCRs targeting specific soil DNA. A single-stranded DNA probe, which was complementary to an internal part of the target gene, was used to coat magnetic beads. After hybridization in a suspension of soil DNA, magnetic extraction of the beads separated the hybrid DNA from all other soil DNA, humic acids, and other interfering soil components. The MCH was followed by PCR amplification of the specific target DNA. In barley rhizosphere soil, detection of a lux gene inserted in a Pseudomonas fluorescens strain could be demonstrated in nonsterile soil samples (0.5 mg). This corresponded to a detection of fewer than 40 bacterial cells per cm of barley root. The MCH-PCR technique greatly improves the current protocols for PCR detection of specific microorganisms or genes in soil because specific target DNA sequences from very small soil samples can be extracted and determined.     

An integrated and sensitive detection platform for magneto-resistive biosensors

A compact biosensor platform with giant magneto-resistive (GMR) sensors suited for the detection of superparamagnetic nanoparticle labels is presented. The platform consist of disposable biosensor cartridges and an electronic reader, which enables quantitative detection with high analytical performance, combined with robustness, ease of use and at low cost. In order to optimise the signal-to-noise ratio (SNR), magnetic labels are excited at high frequency. Wires, integrated in the silicon of the sensor chip are used to generate a well-defined magnetic field on the sensor surface, thus removing the need for mechanical alignment with external apparatus. A signal modulation scheme is applied to obtain optimal detection accuracy. The platform is scalable and can be adapted according to application-specific requirements. Experimental results indicate that three beads of 300 nm diameter can be detected on a sensor surface of 1500 microm2 for a measurement time of 1s.     

An alternative, sensitive method to detect Helicobacter pylori DNA in feces

Background: Despite the high sensitivity and specificity of PCR, detection of Helicobacter pylori DNA in feces is still challenging. Fecal samples contain inhibitory molecules that can prevent amplification of the target DNA. Even by using specific DNA extraction kits for stools, monitoring of infection by analyzing stool samples remains problematic and endorses the need for improved diagnostic methods. Materials and Methods: The newly proposed method uses selective hybridization of target DNA with biotin‐labeled probes, followed by DNA isolation with streptavidin‐coated magnetic beads. After three washing steps, the purified DNA can be amplified immediately using conventional or quantitative PCR. In order to test this technique on biological samples, Mongolian gerbils were infected with H. pylori ATCC 43504 and fecal samples were analyzed on days 1, 4, and 10 post infection. Results: A detection limit of one bacterial cell per 100 mg stool sample was established, but only after removal of the magnetic beads from the target DNA by heating. This resulted in a 10‐fold increase of sensitivity compared to a commercially available stool DNA extraction kit. Analysis of fecal samples from infected gerbils demonstrated the presence of H. pylori DNA on each time point, while the uninfected animal remained negative. Conclusions: The proposed technique allows detection of very low quantities of H. pylori DNA in biological samples. In laboratory animal models, detailed monitoring of infection and complete clearance of infection can be demonstrated thanks to the low detection limit.     

In situ DNA amplification with magnetic primers for the electrochemical detection of food pathogens

A sensitive and selective genomagnetic assay for the electrochemical detection of food pathogens based on in situ DNA amplification with magnetic primers has been designed. The performance of the genomagnetic assay was firstly demonstrated for a DNA synthetic target by its double-hybridization with both a digoxigenin probe and a biotinylated capture probe, and further binding to streptavidin-modified magnetic beads. The DNA sandwiched target bound on the magnetic beads is then separated by using a magneto electrode based on graphite-epoxy composite. The electrochemical detection is finally achieved by an enzyme marker, anti-digoxigenin horseradish peroxidase (HRP). The novel strategy was used for the rapid and sensitive detection of polymerase chain reaction (PCR) amplified samples. Promising resultants were also achieved for the DNA amplification directly performed on magnetic beads by using a novel magnetic primer, i.e., the up PCR primer bound to magnetic beads. Moreover, the magneto DNA biosensing assay was able to detect changes at single nucleotide polymorphism (SNP) level, when stringent hybridization conditions were used. The reliability of the assay was tested for Salmonella spp., the most important pathogen affecting food safety.     

Detection of Fusarium culmorum in wheat by a surface plasmon resonance-based DNA sensor

A surface plasmon resonance (SPR) sensor based on DNA hybridization has been developed for the detection of Fusarium culmorum, a fungal pathogen of cereals. A 0.57 kbp DNA fragment of F. culmorum was amplified by specific primers and a 25-mer oligonucleotide probe was selected within the sequence of the PCR amplicon. After biotinilation, the probe was immobilized on a streptavidin sensor chip and tested for biospecific interaction with PCR products of F. culmorum. The effect of denaturating agents (formamide and urea) and ionic strength (NaCl) on hybridization efficiency of double-stranded PCR products with the immobilized probe and the specificity of the probe were investigated. The SPR biosensor was successfully used for the detection of F. culmorum in culture material of different strains and in naturally infected wheat samples. Tested on fungal cultures, it showed a good selectivity for F. culmorum against other species of either Fusarium or other fungal genera. A background signal was observed in wheat samples strictly depending on the DNA amount of the testing matrix. Testing 30 ng of durum wheat DNA the detection limit was 0.06 pg of F. culmorum DNA. The developed PCR-SPR assay allowed to detect F. culmorum with sensitivity and specificity higher than gel-electrophoresis analysis.     

Combination of competitive quantitative PCR and constant-denaturant capillary electrophoresis for high-resolution detection and enumeration of microbial cells

A novel quantitative PCR (QPCR) approach, which combines competitive PCR with constant-denaturant capillary electrophoresis (CDCE), was adapted for enumerating microbial cells in environmental samples using the marine nanoflagellate Cafeteria roenbergensis as a model organism. Competitive PCR has been used successfully for quantification of DNA in environmental samples. However, this technique is labor intensive, and its accuracy is dependent on an internal competitor, which must possess the same amplification efficiency as the target yet can be easily discriminated from the target DNA. The use of CDCE circumvented these problems, as its high resolution permitted the use of an internal competitor which differed from the target DNA fragment by a single base and thus ensured that both sequences could be amplified with equal efficiency. The sensitivity of CDCE also enabled specific and precise detection of sequences over a broad range of concentrations. The combined competitive QPCR and CDCE approach accurately enumerated C. roenbergensis cells in eutrophic, coastal seawater at abundances ranging from approximately 10 to 10(4) cells x ml(-1). The QPCR cell estimates were confirmed by fluorescent in situ hybridization counts, but estimates of samples with <50 cells x ml(-1) by QPCR were less variable. This novel approach extends the usefulness of competitive QPCR by demonstrating its ability to reliably enumerate microorganisms at a range of environmentally relevant cell concentrations in complex aquatic samples.     

Evaluation of bioelectronics sensor compared to other diagnostic test in diagnosis of Johne's disease in goats

A bioelectronics sensor has been developed and it is evaluated for the diagnosis of paratuberculosis in goats. Initially hematite nanoparticles were prepared and using this nanoparticles as core, electrically active polyaniline coated magnetic (EAPM) nanoparticles are synthesized from aniline monomer (made electrically active by acid doping). These EAPM nanoparticles were fabricated with rabbit anti-goat IgG for the detection of goat antibodies on the capture pad. The protoplasmic antigen of Mycobacterium avium subspecies paratuberculosis (MAP) immobilized onto the capture pad will detect the antibody against MAP in the goat sera samples. This bound goat antibody will be detected by the anti-goat IgG previously bound to EAPM. Upon detection the EAPM nanoparticles bridges an electric circuit between the silver electrodes, flanking the capture membrane. The electrical conductance, caused by EAPM, was measured as direct charge transfer between the electrodes. Testing of the biosensor with known Johne's disease (JD) positive and negative serum samples gave significant difference in the electrical conductance value. Further the efficacy of this biosensor was compared with other serological tests like agar gel immunodiffusion (AGID) and absorbed ELISA using field sera. Out of 265 goat sera tested, positive results recorded were; AGID 36 (13.59%), bioelectronics sensor 49 (19.14%), and absorbed ELISA 51 (19.25%). This biosensor was also compared in live animals using intradermal Johnin test and nested PCR (detecting mycobacterial DNA in feces) in 65 animals. Of which, positive results recorded in animals were; Johnin test 21 (32%), biosensor 26 (40%) and fecal PCR detected mycobacterial DNA in 28 (43%) animals. Though the nanobioelectronics sensor was slightly less sensitive (not statistically significant) compared to absorbed ELISA and fecal nested PCR for mycobacterial DNA but it was simple to perform in field conditions and requires less time. The speed of detection and the equipment involved would support its application toward the various point-of-care opportunities aimed at control and management of Johne's disease in goats.     

A DNA sensor based on surface plasmon resonance for apoptosis-associated genes detection

A practical and simple DNA sensor based on surface plasmon resonance (SPR) had been developed to determine apoptosis-associated genes, bcl-2 and bax. This SPR sensor was designed on the basis of simultaneous multi-wavelength detection. The complementary sequences of bcl-2 or bax oligonucleotide labeled with biotin were used as the probes. Biotin-avidin system was used to immobilize the bio-DNA on the sensor surface. The assembling processes and conditions for the DNA sensor were examined. The SPR sensor could be used to monitor the process of the immobility of the bio-DNA and DNA hybridization in real-time. The determination range of bcl-2 and bax oligonucleotide (20 bases) were 50-400 ng/mL. The determination range of polymerase chain reaction (PCR) product of bcl-2 (405 bases) was 5-60 ng/mL and PCR product of bax (538 bases) was 5-40 ng/mL. The stability, reversibility and specificity of the DNA sensor were also investigated. It was found from the experiment that the sensor could be applied for a quite long time (about 90 times). The relative standard deviation (R.S.D.) for determination oligonucleotides and PCR products of bcl-2 were 1.2 and 1.3%, respectively. The interference of noncomplementary DNA sequence with the determination of DNA was examined and it was found that noncomplementary 20-mer and 21-mer DNA (p53 and p21) do not affect the determination of bcl-2 or bax. This device could be used to study apoptosis and signal transduction routine genes. The sensor was shown to be of simplicity, sensitivity, selectivity, rapid response and cost effectiveness.     

Genotyping of urinary samples stored with EDTA for forensic applications

Individual identification of urinary samples is necessary when sample switching or handling are suspected during a judicial process. To improve the rate of successful genotyping of urinary samples, we examined the stability of DNA in urinary samples stored for up to 30 days. Urinary samples from 20 healthy individuals (10 males and 10 females) were stored at -80°C with different concentrations of EDTA (0, 10 and 40 mM). Urinary DNA was extracted at days 0, 3, 9, and 30 after collection. The Quantifiler Human DNA Quantification Kit was used for measuring DNA concentration. Twenty STR loci were co-amplified using amelogenin-specific PCR with the Goldeneye 20A Kit. Significant differences in DNA concentration were observed between samples from females and males. In the case of female urinary DNA preservation with 10 and 40 mM EDTA the mean detection rate reached 0.95 after up to 30 days; for the male urinary samples, the mean detection rate of urinary DNA preserved with 40 mM EDTA was significantly higher than with 10 mM. We concluded that 40 mM EDTA is the best concentration for preservation of the DNA in urinary samples.     

Label-free and high-sensitive detection of Salmonella using a surface plasmon resonance DNA-based biosensor

A method based on surface plasmon resonance (SPR) DNA biosensor has been developed for label-free and high-sensitive detection of Salmonella. A biotinylated single-stranded oligonucleotide probe was designed to target a specific sequence in the invA gene of Salmonella and then immobilized onto a streptavidin coated dextran sensor surface. The invA gene was isolated from bacterial cultures and amplified using a modified semi-nested asymmetric polymerase chain reaction (PCR) technique. In order to investigate the hybridization detection, experiments with different concentration of synthetic target DNA sequences have been performed. The calibration curve of synthetic target DNA had good linearity from 5 nM to 1000 nM with a detection limit of 0.5 nM. The proposed method was applied successfully to the detection of single-stranded invA amplicons from three serovars of Salmonella, i.e., Typhimurium, Enterica and Derby, and the responses to PCR products were related to different S. typhimurium concentrations in the range from 10(2) to 10(10) CFU mL(-1). While with this system to detect E. coli and S. aureus, no significant signal was observed, demonstrating good selectivity of the method. In addition, the hybridization can be completed within 15 min, and the excellent sensor surface regeneration allows at least 300 assay cycles without obvious loss of performance.     

Sensitive and specific detection of Listeria monocytogenes in milk and ground beef with the polymerase chain reaction.

A sensitive and specific method for detection of Listeria monocytogenes in milk and ground-beef samples is described. It consists of culturing samples in listeria enrichment broth (LEB) and subculturing them from LEB to listeria plating media, followed by DNA extraction and species-specific detection of the organism by using the polymerase chain reaction (PCR). In developing the L. monocytogenes PCR assay, five oligonucleotide primers complementary to the nucleotide sequence of the listeriolysin O gene were synthesized and used in amplification experiments. PCR products of the predicted size, based on nucleotide sequence information, were generated with DNA from all of 72 L. monocytogenes strains with five different primer pairs. DNA from Listeria ivanovii, Listeria innocua, Listeria seeligeri, Listeria welshimeri, Listeria grayi, and Listeia murrayi strains and a panel of 47 bacterial strains representing 17 genera did not generate PCR products with the primer pairs employed. As little as 1 pg of L. monocytogenes DNA could be detected with the assay. To determine the most sensitive culture protocol to use in conjunction with the PCR assay, milk (10 ml) and ground-beef (25 g) samples were inoculated with L. monocytogenes at concentrations ranging from 0 to 10(5) CFU ml-1 or g-1, as appropriate for the sample. PCR assays on DNA extracted from growth on listeria plating media, inoculated with 24-h LEB samples cultures, were most sensitive, allowing detection of as little as 0.1 CFU of L. monocytogenes ml-1 or g-1 of milk and ground beef, respectively.     

Detection of PCR products of Escherichia coli O157:H7 in human stool samples using surface plasmon resonance (SPR)

A method for the rapid detection of verotoxin-producing Escherichia coli O157:H7 in stools was evaluated. Strains possessing Shiga toxin-2 (stx-2) genes were isolated from stool samples and amplified using oligonucleotide primers. Stools spiked with cultured E. coli O157:H7 (strain 298 or strain 1646) were detected to be polymerase chain reaction (PCR) positive at 10(2) cfu per 0.1 g of stool. Stool samples from patients and healthy carriers showed a high correlation between positive results for a PCR and the presence of verotoxin-producing E. coli O157:H7, confirmed by isolation of serotype O157:H7 on sorbitol MacConkey medium (10 of 10 stool samples). These PCR products could be detected using a BIAcore 2000 surface plasmon resonance device using peptide nucleic acid as a sensor probe. In this report we use this method for the rapid detection of DNA from significant pathogenic organisms.     

Polymerase chain reaction for the rapid identification of Clostridium botulinum type A strains and detection in food samples

A polymerase chain reaction (PCR) was developed for the detection of Clostridium botulinum type A, a cause of human botulism. A two primer set and an oligonucleotide detection probe were used to specifically detect Cl. botulinum type A neurotoxin gene (BoNT/A). After 40 cycles of amplification, detection of a 798 bp amplified DNA fragment was carried out by agarose gel electrophoresis and Southern blot hybridization. This assay was able to detect 12.5 fg of purified target DNA or five bacteria per reaction. The sensitivity in artificially contaminated food samples after an 18 h enrichment step ranges from 10 to 10³ bacteria per g according to the type of food samples. No cross-reactions were observed with the other Cl. botulinum toxinotypes and other bacteria found routinely in food. This PCR method may provide a suitable and rapid alternative to standard techniques for detection of Cl. botulinum type A in food samples.     

Magnetic scanometric DNA microarray detection of methyl tertiary butyl ether degrading bacteria for environmental monitoring

A magnetoresistive biosensing platform based on a single magnetic tunnel junction (MTJ) scanning probe and DNA microarrays labeled with magnetic particles has been developed to provide an inexpensive, sensitive and reliable detection of DNA. The biosensing platform was demonstrated on a DNA microarray assay for quantifying bacteria capable of degrading methyl tertiary butyl ether (MTBE), where concentrations as low as 10 pM were detectable. Synthetic probe bacterial DNA was immobilized on a microarray glass slide surface, hybridized with the 48 base pair long biotinylated target DNA and subsequently incubated with streptavidin-coated 2.8 μm diameter magnetic particles. The biosensing platform then makes use of a micron-sized MTJ sensor that was raster scanned across a 3 mm by 5 mm glass slide area to capture the stray magnetic field from the tagged DNA and extract two dimensional magnetic field images of the microarray. The magnetic field output is then averaged over each 100 μm diameter DNA array spot to extract the magnetic spot intensity, analogous to the fluorescence spot intensity used in conventional optical scanners. The magnetic scanning result is compared with results from a commercial laser scanner and particle coverage optical counting to demonstrate the dynamic range and linear sensitivity of the biosensing platform as a potentially inexpensive, sensitive and portable alternative for DNA microarray detection for field applications.     

Sensitive and specific detection of Listeria monocytogenes in milk and ground beef with the polymerase chain reaction.

A sensitive and specific method for detection of Listeria monocytogenes in milk and ground-beef samples is described. It consists of culturing samples in listeria enrichment broth (LEB) and subculturing them from LEB to listeria plating media, followed by DNA extraction and species-specific detection of the organism by using the polymerase chain reaction (PCR). In developing the L. monocytogenes PCR assay, five oligonucleotide primers complementary to the nucleotide sequence of the listeriolysin O gene were synthesized and used in amplification experiments. PCR products of the predicted size, based on nucleotide sequence information, were generated with DNA from all of 72 L. monocytogenes strains with five different primer pairs. DNA from Listeria ivanovii, Listeria innocua, Listeria seeligeri, Listeria welshimeri, Listeria grayi, and Listeia murrayi strains and a panel of 47 bacterial strains representing 17 genera did not generate PCR products with the primer pairs employed. As little as 1 pg of L. monocytogenes DNA could be detected with the assay. To determine the most sensitive culture protocol to use in conjunction with the PCR assay, milk (10 ml) and ground-beef (25 g) samples were inoculated with L. monocytogenes at concentrations ranging from 0 to 10(5) CFU ml-1 or g-1, as appropriate for the sample. PCR assays on DNA extracted from growth on listeria plating media, inoculated with 24-h LEB samples cultures, were most sensitive, allowing detection of as little as 0.1 CFU of L. monocytogenes ml-1 or g-1 of milk and ground beef, respectively.