Citric acid production by Candida lipolytica Y 1095 in cell recycle and fed-batch fermentors

The effect of dissolved oxygen on citric acid production and oxygen uptake by Candida lipolytica Y 1095 was evaluated in cell recycle and fed-batch fermentation systems. The maximum observed volumetric productivity, which occurred at a dilution rate of 0.06 h(-1), a dissolved oxygen concentration of 80%, and a biomass concentration of 5% w/v, in the cell recycle system, was 1.32 g citric acid/L . h. At these same conditions, the citric acid yield was 0.65 g/g and the specific citric acid productivity was 24.9 mg citric acid/g cell . h. In the cell recycle system, citric acid yields ranged from 0.45 to 0.72 g/g. Both the volumetric and specific citric acid productivities were dependent on the dilution rate and the concentration of dissolved oxygen in the fermentor. Similar productivities (1.29 g citric acid/L . h) were obtained in the fed-batch system operated at a cycle time of 36 h, a dissolved oxygen concentration of 80%, and 60 g total biomass. Citric acid yields in the fed-batch fermentor were consistently lower than those obtained in the cell recycle system and ranged from 0.40 to 0.59 g/g. Although citric acid yields in the fed-batch fermentor were lower than those obtained in the cell recycle system, higher citric:isocitric acid ratios were obtained in the fed-batch fermentor. As in the cell recycle system, both the volumetric and specific citric acid productivities in the fed-batch fermentor were dependent on the cycle time and dissolved oxygen concentration. (c) 1995 John Wiley & Sons, Inc.     

Production of 2,3-butanediol in a membrane bioreactor with cell recycle

Summary The production of 2,3-butanediol by Enterobacter aerogenes DSM 30053 was studied in a cell recycle system with a microfiltration module. Emphasis was put on the influence of oxygen supply, cell residence time, dilution rate, and pH. Under optimal conditions a productivity as high as 14.6 g butanediol + acetoin/l per hour was achieved with a product concentration of 54 g/l and a product yield of 88%. This productivity is three times higher than that of an ordinary continuous culture. The achievable final product concentration of a cell recycle system was limited by the accumulation of the inhibiting by-product acetic acid, which increased very rapidly at low dilution rate. To maximize product concentration a fed-batch fermentation was carried out with stepwise pH adaption at high cell density. A final product concentration of 110 g/l was obtained with a productivity of 5.4 g/l per hour and a yield of 97%.     

Performance of a cell recycle bubble column fermentor with a membrane filter module for continuous vinegar production

The steady-state performance of a bubble column combined with a membrane filter module for cell separation and recycle is investigated numerically in the case of vinegar fermentation. The one-dimensional dispersion model for describing the longitudinal mixing of the liquid phase is employed. Kinetic expressions and their parameter values are taken from the available literature. Several characteristics of this fermentor system namely the concentration profiles of cells, substrate and product, the viability of viable cells relative to total cells, the washout condition for cells and the productivity of acetic acid are discussed. The average cell viability in the whole column and the critical dilution rate for washout are presented as equations. Low levels of the axial mixing are found to enhance the vinegar productivity. The optimum dilution rate giving the maximum productivity is determined and both are shown as figures with the Peclet number, the recycle ratio and the bleed ratio as parameters.     

High cell density culture of a recombinant Escherichia coli producing penicillin acylase in a membrane cell recycle fermentor

A recombinant Escherichia coli HB101(pPAKS2) producing penicillin acylase was cultured in a membrane cell recycle fermentor. The strain was very stable throughout the whole experiment. The main inhibitory by-product was acetic acid, and cell growth ceased when its concentration was above 14 g/L Cell density could be increased up to 145 g/L dry weight without experiencing by-product inhibition by regulating glucose concentration in the fermentor and by using total membrane recycle. Acetic acid formation was negligible not only when cells were cultured in medium containing no glucose but also when glucose was limited. Dissolved oxygen control as well as glucose limitation was an indispensable condition for minimizing acetic acid formation when the medium contained glucose. Low concentrations of accumulated acetic acid were reused when glucose was limited. Use of highly concentrated medium reduced the membrane surface area required for cell recycle greatly. The recycle fermentor could be operated in various operational modes including partial bleed and repeated recycle culture to give high productivity. Productivity of a repeated recycle system was over 10 times higher than that of a simple batch system.     

Effect of air supplement on the performance of continuous ethanol fermentation system

For the purpose of improving ethanol productivity, the effect of air supplement on the performance of continuous ethanol fermentation system was studied. The effect of oxygen supplement on yeast concentration, cell yield, cell viability, extracellular ethanol concentration, ethanol yield, maintenance coefficient, specific rates of glucose assimilation, ethanol production, and ethanol productivity have been evaluated, using a high alcohol tolerant Saccharomyces cerevisiae STV89 strain and employing a continuous fermentor equipped with an accurate air metering system in the flow rate range 0-11 mL air/L/h. It was found that, when a small amount of oxygen up to about 80mu mol oxygen/L/h was supplied, the ethanol productivity was significantly enhanced as compared to the productivity of the culture without any air supplement. It was also found that the oxygen supplement improved cell viability considerably as well as the ethanol tolerance level of yeast. As the air supply rate was increased, from 0 to 11 mL air/L/h while maintaining a constant dilution rate at about 0.06 h(-1), the cell concentration increased from 2.3 to 8.2 g/L and the ethanol productivity increased from 1.7 to 4.1 g ethanol/L/h, although the specific ethanol production rate decreased slightly from 0.75 to 0.5 g ethanol/g cell/h. The ethanol yield was slightly improved also with an increase in air supply rate, from about 0.37 to 0.45 ethanol/g glucose. The maintenance coefficient increased by only a small amount with the air supplement. This kind of air supplement technique may very well prove to be of practical importance to a development of a highly productive ethanol fermentation process system especially as a combined system with a high density cell culture technique.     

Co-production of biomass and metabolites by cell retention culture of <Emphasis Type="Italic">Leuconostoc citreum</Emphasis>

Cell retention culture of lactic acid bacterium Leuconostoc citreum was carried out in a fermentor equipped with an internal ceramic filtration system to co-produce biomass and metabolites. The filtration system was composed of porous ceramic filter module with pore size of 0.1 μm and total surface area of 330 cm². High cell density cultivation of L. citreum was achieved within the fermentor, while extracellular metabolites such as mannitol and d-lactic acid were produced through the filter with high productivities. In batch culture of L. citreum using a medium containing 50 g/L of glucose and 100 g/L of fructose, the maximum optical density (OD) monitored at 660 nm was 13 with 65 g/L of mannitol and 38 g/L of lactic acid. In cell retention culture of L. citreum with dilution rate of 0.07 h⁻¹, OD increased to 75, which was 6 times higher than that in batch culture. The concentrations of mannitol and lactic acid increased to 85 and 45 g/L, respectively, and were maintained throughout the cultivation to 105 h. By increasing dilution rate to 0.13 h⁻¹, the productivities of mannitol and lactic acid increased to 8.5 and 4.2 g/L/h, respectively, which were 2.7 to 3 times higher than those in batch culture, suggesting that cell retention culture using internal filtration system is highly effective for co-production of useful cell biomass and various extracellular metabolites.     

Single-cell protein production from spent sulfite liquor utilizing cell-recycle and computer monitoring

Spent sulfite liquor (SSL), a waste product of the paper pulping industry, is produced at a rate of 1 ton (dry basis) per ton of pulp. The sugar content of SSL is about 30 g/L. To reduce the biological oxygen demand (BOD) of SSL before disposal, torula yeast (Candida utilis) is produced by a continuous culture process, the productivity of which is limited by sugar concentration and cell growth rate. To increase productivity, a recycle system has been designed and tested. Cells were sedimented continuously with a flocculating agent (bentonite) before being recycled to the fermentor. A bentonite concentration of 0.02 g/g cell was required. A computer monitoring system based on material balancing techniques was developed to monitor and control the recycle system. With this computer system, productivity was raised to 6.1 g/L h, with cell concentration up to 65 g/L in the recycle stream and 24 g/L in the fermentor. This represents a productivity increase of 150% over continuous culture with no recycle.     

Acetic Acid Production by an Electrodialysis Fermentation Method with a Computerized Control System

In acetic acid fermentation by Acetobacter aceti, the acetic acid produced inhibits the production of acetic acid by this microorganism. To alleviate this inhibitory effect, we developed an electrodialysis fermentation method such that acetic acid is continuously removed from the broth. The fermentation unit has a computerized system for the control of the pH and the concentration of ethanol in the fermentation broth. The electrodialysis fermentation system resulted in improved cell growth and higher productivity over an extended period; the productivity exceeded that from non-pH-controlled fermentation. During electrodialysis fermentation in our system, 97.6 g of acetic acid was produced from 86.0 g of ethanol; the amount of acetic acid was about 2.4 times greater than that produced by non-pH-controlled fermentation (40.1 g of acetic acid produced from 33.8 g of ethanol). Maximum productivity of electrodialysis fermentation in our system was 2.13 g/h, a rate which was 1.35 times higher than that of non-pH-controlled fermentation (1.58 g/h).     

Continuous conversion of D-xylose to ethanol by immobilized pachysolen tannophilus

The yeast Pachysolen tannophilus was entrapped in calcium alginate beads to ferment D-xylose on a continous basis in the presence of high cell densities. Experimental operating variables included the feed D-xylose concentration, the dilution rate, and the fermentor biomass concentration. Under favorable operating conditions, cultures retained at least 50% of their initial productivity after 26 days of operation. The specific ehanol production rate was dependent on the substrate level in the fermentor, passing through an optimum when the D-xylose concentration was between 28 and 35 g/L. Consequently, reactor productivity increased with dilution rate and feed D-xylose concentration until a maximum was reached. The ethanol content of the effluent always decreased with increasing dilution rate, but excessive dilution rates diminished the ethanol content without increasing productivity. Unlike production rate, ethanol yield declined monotonically from 0.35 g/g as the fermentor substrate concentration increased. The yield was 69% of that theoretically possible when the D-xylose concentration was near zero, as opposed to 42% when it was in the range supporting the optimum specific rate of ethanol production. As long as D-xylose was supplied to cells faster than they could consume it, productivity increased with the mass of cells immobilized. The effectiveness factor associated with the calcium alginte beads used in this system was 0.4, indicating that only 40% of the entrapped biomass was effective in converting D-xylose to ethanol because of diffusion limitations.     

Ethanol fermentation in a yeast immobilized tubular fermentor

In this article, a mathematical model describing the kinetics of ethanol fermentation in a whole cell immobilized tubular fermentor is proposed. Experimental results show reasonable agreement with the proposed model. A procedure for treating the fermentation data for determining the ethanol inhibition constants k(1) and k(2) is described. The ethanol productivity of the immobilized cell fermentor is compared with those of traditional fermentors. Experimental studies indicate that with Saccharomyces cerevisiae (NRRL Y132) culture, ethanol productivity in the range 21.2-83.7 g ethanol L(-1) h(-1) at ethanol concentration of 76-60 g/L can be achieved. This is comparable to or higher than those reported in the literature for yeast. The product yield factor of 0.5 g ethanol/g glucose was obtained. The immobilized cell fermentor does not show washout at dilution rates of 7 h(-1) and shows good stability over a 650-h operating period.     

Relieving effects of glycine and methionine from acetic acid inhibition in Escherichia coli fermentation

Among amino acids screened for their potential to relieve wild and recombinant Escherichia coli from the negative effects of acetic acid, glycine, and methionine showed a sparing effect. In the presence of 2 g/L of acetic acid, addition of 0.5 g/L of glycine or methionine resulted in either a complete recovery or a further enhancement in the specific growth rate, while the enhancement was significant but not fully complete in the presence of 4 g/L of acetic acid. The addition of 0.5 g/L of methionine alleviated the negative effect of acetic acid on recombinant E. Coli growth to produce more beta-lactamase, which was encoded by plasmid pUC18. In continuous fermentation the methionine effect on recombinant. E. coli metabolism depended on dilution rate; at high dilution rates, above 0.4 h(-1), the methionine addition enhanced beta-lactamase production and reduced acetic acid formation, while at low dilution rates, below 0.3 h (-1), the effect was reversed. In def-batch fermentation with wild-type E. Coli, cell growth rate and cell yield from glucose were enhanced with methionine addition, while the acetic acid concentration reached over 4 g/L. (c) 1993 John Wiley & Sons, Inc.     

Production of ethanol by Clostridium thermosaccharolyticum: I. Effect of cell recycle and environmental parameters

The direct microbial conversion (DMC) process for the production of ethanol from lignocellulosic biomass is limited by low volumetric ethanol production rates due to the low cell densities of Clostridium thermosaccharolyticum which is a key organism for ethanol production in this process. Hence, this study focuses on the use of a continuous- culture cell recycle system to improve the volumetric ethanol productivity and yield of the fermentation of xylose by C. thermosaccharolyticum. Early experiments with the continuous-culture cell recycle system showed a two-fold improvement in volumetric ethanol productivity. However, the ethanol yield at the higher dilution rates suffered because of the large amount of lactate produced. The manipulation of two environmental parameters-iron concentration in the nutrient medium and the N(2) purge rate of the fermentor headspace-allowed a dramatic reduction in the lactate production and a simultaneous improvement in the ethanol titer and yield. Under the improved conditions of increased iron concentration (12.5 mg/L FeSO(4) . 7H(2)O) and decreased N(2) purge rate (0.1 L/min), a continuous culture of C. thermosaccharolyticum operating at a dilution rate of 0.24 h(-1) and 50% cell recycle produced 8.6 g/L ethanol and less than 1 g/L each of acetate and lactate. The volumetric ethanol productivity was 2.2 g/L/h, which is 8 times larger than obtained for a continuous culture operated with no cell recycle and the same specific growth rate.     

Acetate production from whey lactose using co-immobilized cells of homolactic and homoacetic bacteria in a fibrous-bed bioreactor

Acetate was produced from whey lactose in batch and fed-batch fermentations using co-immobilized cells of Clostridium formicoaceticum and Lactococcus lactis. The cells were immobilized in a spirally wound fibrous sheet packed in a 0.45-L column reactor, with liquid circulated through a 5-L stirred-tank fermentor. Industrial-grade nitrogen sources, including corn steep liquor, casein hydrolysate, and yeast hydrolysate, were studied as inexpensive nutrient supplements to whey permeate and acid whey. Supplementation with either 2.5% (v/v) corn steep liquor or 1.5 g/L casein hydrolysate was adequate for the cocultured fermentation. The overall acetic acid yield from lactose was 0.9 g/g, and the productivity was 0.25 g/(L h). Both lactate and acetate at high concentrations inhibited the homoacetic fermentation. To overcome these inhibitions, fed-batch fermentations were used to keep lactate concentration low and to adapt cells to high-concentration acetate. The final acetate concentration obtained in the fed-batch fermentation was 75 g/L, which was the highest acetate concentration ever produced by C. formicoaceticum. Even at this high acetate concentration, the overall productivity was 0.18 g/(L h) based on the total medium volume and 1.23 g/(L h) based on the fibrous-bed reactor volume. The cells isolated from the fibrous-bed bioreactor at the end of this study were more tolerant to acetic acid than the original culture used to seed the bioreactor, indicating that adaptation and natural selection of acetate-tolerant strains occurred. This cocultured fermentation process could be used to produce a low-cost acetate deicer from whey permeate and acid whey.     

Ethanol production in a hollow fiber bioreactor using Saccharomyces cerevisiae

Summary A new approach for continuous production of ethanol was developed using a Hollow fiber fermentor (HFF). Saccharomyces cerevisiae cells were packed into the shell-side of a hollow fiber module. Using 100 g/l glucose in the feed gave an optimum ethanol productivity, based on total HFF volume, of 40 g ethanol/l/h at a dilution rate of 3.0 h^-1. Under these conditions, glucose utilization was 30%. However, at 85% glucose utilization the productivity was 10 g ethanol/l/h. This compares to batch fermentor productivity of 2.1 g ethanol/l/h at 100% glucose utilization.     

Controlled biomass formation and kinetics of toluene degradation in a bioscrubber and in a reactor with a periodically moved trickle-bed

The kinetics of degradation of toluene from a model waste gas and of biomass formation were examined in a bioscrubber operated under different nutrient limitations with a mixed culture. The applicability of the kinetics of continuous cultivation of the mixed culture was examined for a special trickle-bed reactor with a periodically moved filter bed. The efficiency of toluene elimination of the bioscrubber was 50 to 57% and depended on the toluene mass transfer as evident from a constant productivity of 0.026 g dry cell weight/L . h over the dilution rate. Under potassium limitation the biomass productivity was reduced by 60% to 0.011 g dry cell weight/L . h at a dilution rate of 0.013/h. Conversely, at low dilution rates the specific toluene degradation rates increased. Excess biomass in a trickle-bed reactor causes reduction of interfacial area and mass transfer, and increase in pressure drop. To avoid these disadvantages, the trickle-bed was moved periodically and biomass was removed with outflowing medium. The concentration of steady state biomass fixed on polyamide beads decreased hyperbolically with the dilution rate. Also, the efficiency of toluene degradation decreased from 72 to 56% with increasing dilution rate while the productivity increased. Potassium limitation generally caused a reduction in biomass, productivity, and yield while the specific degradation increased with dilution rate. This allowed the application of the principles of the chemostat to the trickle-bed reactor described here, for toluene degradation from waste gases. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 686-692, 1997.     

自絮凝酵母SPSC01在组合反应器系统中酒精连续发酵的研究

建立了一套由四级磁力搅拌发酵罐串联组成、总有效容积4000mL的小型组合生物反应器系统 ,其中一级罐作为种子培养罐。以脱胚脱皮玉米粉双酶法制备的糖化液为种子培养基和发酵底物 ,进行了自絮凝颗粒酵母酒精连续发酵的研究。种子罐培养基还原糖浓度为100g L ,添加 (NH₄)₂HPO₄ 和KH₂PO₄ 各 20g L ,以0.017h^-1 的恒定稀释速率流加 ,并溢流至后续酒精发酵系统。发酵底物初始还原糖浓度 220g/L ,添加 (NH₄)₂HPO₄ 15g/L和KH₂PO₄2 5g/L ,流加至第一级发酵罐 ,稀释速率分别为 0.017、0.025、0.033、0.040和0.05 0h^-1。实验数据表明 ,自絮凝颗粒酵母在各发酵罐中呈部分固定化状态 ,在稀释速率0.040h^-1 条件下 ,发酵系统呈一定的振荡行为 ,其他四个稀释速率实验组均能够达拟稳态。当稀释速率不超过 0 0 33h^-1 ,流出末级发酵罐的发酵液中酒精浓度可以达到 12 % (V/V)以上 ,残还原糖和残总糖分别在 0 11%和 0 35 % h^-1,流出末级发酵罐的发酵液中酒精浓度可以达到12%（V/V）以上,残还原糖和残总糖分别在0.11%和0.35%（W/V）以下。在稀释速率为0.033h^-1时,计算发酵系统酒精的设备生产强度指标为3.32（g·L^-1·h^-1）,与游离酵母细胞传统酒精发酵工艺相比,增加约1倍。     

Continuous conversion of rice starch hydrolysate to 2-keto-D-gluconic acid by Arthrobacter globiformis C224

A continuous conversion process of rice starch hydrolysate to 2-keto-D-gluconic acid (2KGA) by Arthrobacter globiformis C224 was developed. Its feasibility for industrial application was also evaluated. Results showed that the initial cell concentration exceeding 1.25 g/L met the continuous 2KGA production at a stable dilution rate and media composition, while the dilution rate and feeding glucose concentration had a significant effect on 2KGA production performance. The optimal operating parameters were obtained as: 0.090/h of dilution rate and 171.0 g/L of feeding glucose concentration. Under these conditions, the steady state had a produced 2KGA concentration of 124.74 g/L, average volumetric productivity of 11.23 g/L/h, and yield of 0.97 g/g. In conclusion, continuous 2KGA production by the A. globiformis C224 strain would be a superior industrial process for the production of 2KGA in terms of its high 2KGA productivity and yield.     

表达血管生长抑制素的重组毕赤酵母在诱导阶段混合碳源的流加

为进行高密度发酵并实现外源基因的高表达,在表型为Mut^S的重组毕赤酵母（Pichia pastoris）表达人血管生长抑制素的诱导阶段,采用了甘油甲醇混合补料的培养方式。以溶氧水平作为甘油代谢指针来控制甘油限制性流加既可维持一定菌体生长,又不会发生发酵液中残余甘油及有害代谢产物（乙醇）阻遏蛋白表达。当表达阶段的菌体平均比生长速率控制于0.012h^-1,菌体浓度达150 g/L,血管生长抑制素浓度最高达到108 mg/L,血管生长抑制素的平均比生产速率为0.02 mg/(g·h),菌体关于甘油的表观得率为0.69 g/g,菌体关于甲醇的表观得率为0.93g/g,较没有采用甘油限制性流加时都有所提高。     

A dense cell retention culture system using stirred ceramic membrane reactor

A novel reactor design incorporating porous ceramic tubes into a stirred jar fermentor was developed. The stirred ceramic membrane reactor has two ceramic tubular membrane units inside the vessel and maintains high filtration flux by alternating use for filtering and recovering from clogging. Each filter unit was linked for both extraction of culture broth and gas sparging. High permeability was maintained for long periods by applying the periodical control between filtering and air sparging during the stirred retention culture of Saccharomyces cerevisiae. The ceramic filter aeration system increased the k(L)a to about five times that of ordinary gas sparing. Using the automatic feeding and filtering system, cell mass concentration reached 207 g/L in a short time, while it was 64 g/L in a fed-batch culture. More than 99% of the growing cells were retained in the fermentor by the filtering culture. Both yield and productivity of cells were also increased by controlling the feeding of fresh medium and filtering the supernatant of the dense cells culture. (c) 1994 John Wiley & Sons, Inc.     

产琥珀酸重组大肠杆菌的发酵性能研究

研究了重组大肠杆菌JM001(△ppc)/pTrc99a-pck发酵产琥珀酸的性能,结果表明厌氧条件下其耗糖能力和产酸能力分别为对照菌株JM001的4.2倍和15.3倍。进一步优化发酵条件表明：采用接入菌泥的发酵方式比按照10%接种量转接厌氧发酵的效果要好,琥珀酸的对葡萄糖的质量收率提高了约10%,且副产物乙酸的量进一步降低。初始葡萄糖浓度高于60g/L时会对菌株的生长和产酸产生抑制,且浓度越高,抑制作用越明显。7L发酵罐放大实验中,整个厌氧发酵阶段葡萄糖的消耗速率为0.42g/(L.h),琥珀酸对葡萄糖的质量收率为67.75%,琥珀酸的生产强度为0.28g/(L.h)。