Use of surface plasmon-coupled emission to measure DNA hybridization

The authors describe a new approach to measuring DNA hybridization based on surface plasmon-coupled emission (SPCE). SPCE is the resonance coupling of excited fluorophores with electron motions in thin metal films, resulting in efficient transfer of energy through the film and radiation into the glass substrate. The authors evaluated the use of SPCE for detection of DNA hybridization. An unlabeled capture biotinylated oligonucleotide was attached near the surface of a thin (50 nm) silver film using streptavidin. The authors then measured the emission intensity of single-stranded Cy5-labeled DNA upon binding to a complementary oligomer attached to a silver film. Hybridization could be detected by an increase in SPCE, which appeared as light radiated into the substrate at a sharply defined angle near 73 degrees from the normal. The largest signals were observed when the excitation angle of incidence equaled the surface plasmon wavelength, but directional emission was also observed without excitation by the surface plasmon evanescent field. The increased intensity is due to proximity to the metal surface, so that hybridization can be detected without a change in the quantum yield of the fluorophore. These results indicate that SPCE can provide highly sensitive real-time measurement of DNA hybridization.     

Directional surface plasmon-coupled emission: application for an immunoassay in whole blood

We present a new approach for performing fluorescence immunoassay in whole blood using fluorescently labeled anti-rabbit immunoglobulin G (IgG) on a silver surface. This approach, which is based on surface plasmon-coupled emission (SPCE), provides increased sensitivity and substantial background reduction due to exclusive selection of the signal from the fluorophores located near a bioaffinity surface. This article describes the effect of an optically dense sample matrix, namely human whole blood and serum, on the intensity of the SPCE. An antigen (rabbit IgG) was adsorbed to a slide covered with a thin silver metal layer, and the SPCE signal from the fluorophore-labeled anti-rabbit antibody, binding to the immobilized antigen, was detected. The effect of the sample matrix (buffer, human serum, or human whole blood) on the end-point immunoassay SPCE signal was studied. It was demonstrated that the kinetics of binding could be monitored directly in whole blood or serum. The results showed that human serum and human whole blood attenuate the SPCE end-point signal and the immunoassay kinetic signal only approximately two- and threefold, respectively, as compared with buffer, resulting in signals that are easily detectable even in whole blood. The high optical absorption of the hemoglobin can be tolerated because only fluorophores within a couple of hundred nanometers from the metallic film contribute to SPCE. Excited fluorophores outside the 200-nm layer do not contribute to SPCE, and their free space emission is not transmitted through the opaque metallic film into the glass substrate. We believe that SPCE has the potential of becoming a powerful approach for performing immunoassays based on surface-bound analytes or antibodies for many biomarkers directly in dense samples such as whole blood with no need for washing steps.     

Radiative decay engineering 4. Experimental studies of surface plasmon-coupled directional emission

Fluorescence is typically isotropic in space and collected with low efficiency. In this paper we describe surface plasmon-coupled emission (SPCE), which displays unique optical properties and can be collected with an efficiency near 50%. SPCE occurs for fluorophores within about 200 nm of a thin metallic film, in our case a 50-nm-thick silver film on a glass substrate. We show that fluorophore proximity to this film converts the normally isotropic emission into highly directional emission through the glass substrate at a well-defined angle from the normal axis. Depending on the thickness of the polyvinyl alcohol (PVA) film on the silver, the coupling efficiency of sulforhodamine 101 in PVA ranged from 30 to 49%. Directional SPCE was observed whether the fluorophore was excited directly or by the evanescent field due to the surface plasmon resonance. The emission is always polarized perpendicular to the plane of incidence, irrespective of the polarization of the incident light. The lifetimes are not substantially changed, indicating a mechanism somewhat different from that observed previously for the effects of silver particles on fluorophores. Remarkably, the directional emission shows intrinsic spectral resolution because the coupling angles depend on wavelength. The distances over which SPCE occurs, 10 to 200 nm, are useful because a large number of fluorophores can be localized within this volume. The emission of more distant fluorophores does not couple into the glass, allowing background suppression from biological samples. SPCE can be expected to become rapidly useful in a variety of analytical and medical sensing applications.     

Directional surface plasmon-coupled emission: A new method for high sensitivity detection

Fluorescence emission is nearly isotropic in space. With typical optical components the collection efficiency is 1% or less. In this preliminary report, we describe a novel approach to transforming the normally isotropic emission into directional emission with a collection efficiency near 50%. This can be accomplished for fluorophores located near a semi-transparent silver film on a glass substrate. The emission couples with the surface plasmon resonance on the silver surface and enters the transparent substrate at a sharply defined angle, the surface plasmon angle for the emission wavelength. We estimate that 40-70% of the total emission enters the substrate at the plasmon angle and can thus be directed towards a detector. Background emission from fluorophores distant from the silver does not couple with the plasmon and is not detected. Different emission wavelengths couple at different angles allowing spectral discrimination without additional optics. Surface plasmon-coupled emission represents a new technology which can be used for high detection efficiency with microfluidic and/or surface-bound assay formats.     

Radiative decay engineering 7: Tamm state-coupled emission using a hybrid plasmonic–photonic structure

There is a continuing need to increase the brightness and photostability of fluorophores for use in biotechnology, medical diagnostics, and cell imaging. One approach developed during the past decade is to use metallic surfaces and nanostructures. It is now known that excited state fluorophores display interactions with surface plasmons, which can increase the radiative decay rates, modify the spatial distribution of emission, and result in directional emission. One important example is surface plasmon-coupled emission (SPCE). In this phenomenon, the fluorophores at close distances from a thin metal film, typically silver, display emission over a small range of angles into the substrate. A disadvantage of SPCE is that the emission occurs at large angles relative to the surface normal and at angles that are larger than the critical angle for the glass substrate. The large angles make it difficult to collect all of the coupled emission and have prevented the use of SPCE with high-throughput and/or array applications. In the current article, we describe a simple multilayer metal–dielectric structure that allows excitation with light that is perpendicular (normal) to the plane and provides emission within a narrow angular distribution that is normal to the plane. This structure consists of a thin silver film on top of a multilayer dielectric Bragg grating, with no nanoscale features except for the metal or dielectric layer thicknesses. Our structure is designed to support optical Tamm states, which are trapped electromagnetic modes between the metal film and the underlying Bragg grating. We used simulations with the transfer matrix method to understand the optical properties of Tamm states and localization of the modes or electric fields in the structure. Tamm states can exist with zero in-plane wavevector components and can be created without the use of a coupling prism. We show that fluorophores on top of the metal film can interact with the Tamm state under the metal film and display Tamm state-coupled emission (TSCE). In contrast to SPCE, the Tamm states can display either S or P polarization. The TSCE angle is highly sensitive to wavelength, which suggests the use of Tamm structures to provide both directional emission and wavelength dispersion. Metallic structures can modify fluorophore decay rates but also have high losses. Photonic crystals have low losses but may lack the enhanced light-induced fields near metals. The combination of plasmonic and photonic structures offers the opportunity for radiative decay engineering to design new formats for clinical testing and other fluorescence-based applications.     

Solution-Deposited Thin Silver Films on Plastic Surfaces for Low-Cost Applications in Plasmon-Coupled Emission Sensors

We report the deposition of highly uniform thin silver films on plastic materials using a wet-chemistry method, suitable for surface plasmon-coupled emission (SPCE). This approach is reproducible for diverse low-cost applications and versatile to generate silver surfaces on various plastics substrates. An oxygen plasma pretreatment of the plastic provides for rapid silvering, leading to a 47-nm-thick continuous film for SPCE applications. The surface smoothness and thickness of the films have been estimated using atomic force microscope. The higher refractive index of polycarbonate, resulted in an SPCE angle of θ _F = 47⁰ for Rhodamine B, compared to glass (θ _F = 50⁰). The current study presents details on film deposition conditions, appropriate choice of index matching fluids, substrates, and light sources that play a vital role to augment SPCE emission intensity.     

Directional surface plasmon-coupled emission from a 3 nm green fluorescent protein monolayer

High-sensitivity detection schemes are of great interest for a number of applications. Unfortunately, such schemes are usually high-cost. We demonstrate a low-cost approach to a high-sensitivity detection scheme based on surface plasmon-coupled emission (SPCE). The SPCE of a monomolecular layer of green fluorescent protein (GFP) is reported here. The protein was electrostatically attached to a thin, SiO(2)-protected silver film deposited on a quartz substrate. The visible, directional emission of GFP was observed at a sharp, well-defined angle of 47.5 degrees from the normal to the coupling prism, and the spectrum corresponded to that of GFP. The SPCE resulting from the reverse Kretschmann configuration showed a 12-fold enhancement over the free space fluorescence. The directional emission was 97% p-polarized. The directionality and high polarization can be coupled with the intrinsic spectral resolution of SPCE to be used in the design miniaturized spectrofluorometers. The observation of SPCE in the visible region of the spectrum from a monolayer of protein opens up new possibilities in protein-based sensing.     

Radiative decay engineering 3. Surface plasmon-coupled directional emission

A new method of fluorescence detection that promises to increase sensitivity by 20- to 1000-fold is described. This method will also decrease the contribution of sample autofluorescence to the detected signal. The method depends on the coupling of excited fluorophores with the surface plasmon resonance present in thin metal films, typically silver and gold. The phenomenon of surface plasmon-coupled emission (SPCE) occurs for fluorophores 20-250 nm from the metal surface, allowing detection of fluorophores over substantial distances beyond the metal-sample interface. SPCE depends on interactions of the excited fluorophore with the metal surface. This interaction is independent of the mode of excitation; that is, it does not require evanescent wave or surface-plasmon excitation. In a sense, SPCE is the inverse process of the surface plasmon resonance absorption of thin metal films. Importantly, SPCE occurs over a narrow angular distribution, converting normally isotropic emission into easily collected directional emission. Up to 50% of the emission from unoriented samples can be collected, much larger than typical fluorescence collection efficiencies near 1% or less. SPCE is due only to fluorophores near the metal surface and may be regarded as emission from the induced surface plasmons. Autofluorescence from more distal parts of the sample is decreased due to decreased coupling. SPCE is highly polarized and autofluorescence can be further decreased by collecting only the polarized component or only the light propagating with the appropriate angle. Examples showing how simple optical configurations can be used in diagnostics, sensing, or biotechnology applications are presented. Surface plasmon-coupled emission is likely to find widespread applications throughout the biosciences.     

Studies of Surface-Adsorbed Fluorescently Labeled Casein and Concanavalin A Using Surface Plasmon-Coupled Emission

We report the use of surface plasmon-coupled emission (SPCE) as an analytical tool to study the photophysics of surface-adsorbed fluorescently labeled proteins. The study uses plasma etching of PMMA surface followed by deposition of poly(diallyldimethylammonium chloride) (PDDA) for surface protein detection. PDDA increases the overall amount of the captured protein and also promotes dye aggregation. The photon-sorting properties of the SPCE process allows for wavelength separation of the individual components from the protein–dye aggregates. This has been exploited to study the fluorescence emissions from casein labeled with fluorescein isothiocyanate and concanavalin A labeled with tetramethylrhodamine. Based on the current findings, the proteins can be used to measure background fluorescence or to monitor the microenvironments in fluoroimmunoassays on SPCE substrates.     

Surface plasmon resonance imaging on a microchip for detection of DNA-modified gold nanoparticles deposited onto the surface in a non-cross-linking configuration

We report theoretical predictions and experimental observations of the reduced detection volume with the use of surface-plasmon-coupled emission (SPCE). The effective fluorescence volume (detection volume) in SPCE experiments depends on two near-field factors: the depth of evanescent wave excitation and a distance-dependent coupling of excited fluorophores to the surface plasmons. With direct excitation of the sample (reverse Kretschmann excitation) the detection volume is restricted only by the distance-dependent coupling of the excitation to the surface plasmons. However, with the excitation through the glass prism at surface plasmon resonance angle (Kretschmann configuration), the detection volume is a product of evanescent wave penetration depth and distance-dependent coupling. In addition, the detection volume is further reduced by a metal quenching of excited fluorophores at a close proximity (below 10nm). The height of the detected volume size is 40-70nm, depending on the orientation of the excited dipoles. We show that, by using the Kretschmann configuration in a microscope with a high-numerical-aperture objective (1.45) together with confocal detection, the detection volume can be reduced to 1-2attoL. The strong dependence of the coupling to the surface plasmons on the orientation of excited dipoles can be used to study the small conformational changes of macromolecules.     

Silver ion microplates for immunoassays.

Microplate wells can be coated with silver ions using glutaraldehyde as a spacer molecule and thiourea as a complexing ligand. Microwells containing surface silver ions are shown to immobilize biotin-labeled horseradish peroxidase (HRP) in active form, while showing very little affinity for the unlabeled enzyme. These plates can also immobilize biotin-labeled antibodies that exhibit bioactivity after immobilization. Silver ions are needed for the complexation of the biotinylated enzyme or antibody because microwells modified to contain surface amine or thiourea molecules do not immobilize appreciable amounts of the labeled proteins. A maximum surface coverage for biotin-labeled HRP of 40 ng/cm2 and an immobilization binding constant of Km = 8 x 10(9)/M are determined from serial dilutions in a microplate. Detection of as little as 6.7 fmol HRP is achieved using antibodies immobilized on the silver ion-modified microplates. Active antibody surface densities were estimated to be between 130 and 260 nm2/antibody molecule. Background binding of HRP to the modified silver ion microplates was very low, allowing for reasonably accurate detection between 10(-14) and 10(-11) mol HRP.     

Enhanced detection sensitivity of pegylated CdSe/ZnS quantum dots-based prostate cancer biomarkers by surface plasmon-coupled emission

We demonstrate the fabrication and detection of quantum dots (QDs)-based prostate specific antigens (PSAs) cancer protein biochips by using enhanced surface plasmon-coupled emission measurements (SPCE). The PSAs are immobilized on a SiO(2)-protected thin gold substrate and pegylated QDs which conjugated with antibodies of PSA are used as fluorescent probes. Due to the excellent brightness of the QDs and the high directionality of emission, as well as the high light collection efficiency of SPCE, the limit of detection (LOD) is down to 10 fg/mL (equal to 0.3 fM) for the PSA chips by using QDs-based cancer protein. We expect that this QDs-based SPCE measurement system with the low LOD supplies a great potential for detecting various cancer biomarkers that are present in only low concentrations within the human body.     

Mapping fluorophore distributions in three dimensions by quantitative multiple angle-total internal reflection fluorescence microscopy.

The decay of evanescent field intensity beyond a dielectric interface depends upon beam incident angle, enabling the 3-d distribution of fluorophores to be deduced from total internal reflection fluorescence microscopy (TIRFM) images obtained at multiple incident angles. Instrumentation was constructed for computer-automated multiple angle-TIRFM (MA-TIRFM) using a right angle F2 glass prism (n(r) 1.632) to create the dielectric interface. A laser beam (488 nm) was attenuated by an acoustooptic modulator and directed onto a specified spot on the prism surface. Beam incident angle was set using three microstepper motors controlling two rotatable mirrors and a rotatable optical flat. TIRFM images were acquired by a cooled CCD camera in approximately 0.5 degree steps for >15 incident angles starting from the critical angle. For cell studies, cells were grown directly on the glass prisms (without refractive index-matching fluid) and positioned in the optical path. Images of the samples were acquired at multiple angles, and corrected for angle-dependent evanescent field intensity using "reference" images acquired with a fluorophore solution replacing the sample. A theory was developed to compute fluorophore z-distribution by inverse Laplace transform of angle-resolved intensity functions. The theory included analysis of multiple layers of different refractive index for cell studies, and the anisotropic emission from fluorophores near a dielectric interface. Instrument performance was validated by mapping the thickness of a film of dihexyloxacarbocyanine in DMSO/water (n(r) 1.463) between the F2 glass prism and a plano-convex silica lens (458 mm radius, n(r) 1.463); the MA-TIRFM map accurately reproduced the lens spherical surface. MA-TIRFM was used to compare with nanometer z-resolution the geometry of cell-substrate contact for BCECF-labeled 3T3 fibroblasts versus MDCK epithelial cells. These studies establish MA-TIRFM for measurement of submicroscopic distances between fluorescent probes and cell membranes.     

Direct monitoring of molecular recognition processes using fluorescence enhancement at colloid-coated microplates

Direct monitoring of recognition processes at the molecular level is a valuable tool for studying reaction kinetics to assess affinity constants (e.g. drugs to receptors) and for designing rapid single step immunoassays. Methods currently used to gain information about binding processes predominantly depend on surface plasmon resonance. These systems use excitation with coherent light in attenuated total reflection geometry to obtain discrimination between surface-bound and free molecules in solution. Therefore labeling of the compounds is not necessary, but due to the complexity of the measuring setup the method is rather costly. In this contribution we present a simple method for performing kinetic single step biorecognition assays with fluorophore labeled compounds using the fluorescence enhancement properties of surface bound silver colloids. Silver colloids are bound to standard microplates via silanization of the plastic surface. Fluorophores close to this colloid coated surface show a significant gain in fluorescence compared to fluorophores farther away in the bulk solution. Therefore discrimination between surface bound and free fluorophores is possible and the binding of, for example, fluorophore labeled antibodies to antigens immobilized on the colloid surface results in increasing fluorescence intensity. Utilization of standard microplates makes this method fully compatible with conventional microplate processing and reading devices. Neither excitation with coherent laser light nor ATR geometry is required, the measurement is performed in a standard fluorescence microplate reader in front face geometry with a xenon flash lamp as excitation source. Methods for the preparation of colloid-coated microplates and fluorescence-enhanced biorecognition assays are presented. Additionally the dependence of the system performance on the structure and properties of the metal colloid coated surface is described. A two-component biorecognition model system shows a detection limit in the subnanomolar range. The ease of colloid-surface preparation and the high sensitivity makes fluorescence enhancement at colloid-coated microplates a valuable tool for studying reaction kinetics and performing rapid single-step immunoassays.     

Metal particle-enhanced fluorescent immunoassays on metal mirrors

We present fluoroimmunoassays on plain metal-coated surfaces (metal mirrors) enhanced by metal nanoparticles (silver island films [SIFs]). Metal mirrors (aluminum, gold, or silver protected with a thin silica layer) were coated with SIFs, and an immunoassay (model assay for rabbit immunoglobulin G or myoglobin immunoassay) was performed on this surface using fluorescently labeled antibodies. Our results showed that SIFs alone (on glass surface not coated with metal) enhance the immunoassay signal approximately 3- to 10-fold. Using a metal mirror instead of glass as support for SIFs results in up to 50-fold signal enhancement.     

Ultrabright fluorescein-labeled antibodies near silver metallic surfaces

Fluorescein-labeled antibodies are widely used in clinical assays and fluorescence microscopy. The fluorescent signal per labeled antibody is limited by fluorescein self-quenching, which occurs when the antibody is heavily labeled with multiple fluoresceins. We examined immunoglobulin G (IgG) when labeled with 0.7 to about 30 fluoresceins per antibody molecule. The extent of self-quenching was decreased, and the signal increased, when the labeled antibody was in close proximity to metallic silver particles. Time-resolved measurements showed that the intensity increase was due in part to a silver-induced increase in the radiative decay rate. These results suggest the use of labeled antibodies conjugated to silver particles as ultrabright probes for imaging or analytical applications.     

A comparison of silver ion to streptavidin coated microplates

Direct comparisons are made between covalently linked streptavidin and silver ion coated microplates. Both coatings can immobilize biotinylated molecules. Silver ion coated microplate wells can immobilize 1.8 times higher amounts of biotin labeled horseradish peroxidase. The quantitation range and capacity for the capture of horseradish peroxidase using biotin labeled horseradish peroxidase are also greater for silver ion coated microplates. Approximately twice as many anti-horseradish peroxidase antibodies can be immobilized per well using silver ion coated microplates. Higher capacities are presumed to be due to the smaller footprint of silver ions as compared to streptavidin. A direct comparison between the two coatings for a beta-galactosidase ELISA showed that while the silver ion coated microplates gave higher readings, the streptavidin coated microplates exhibited smaller well-to-well variation. However, higher well to well variation for the silver microplates is attributed to the high density of anti-beta-galactosidase antibodies on the microplates and the weak binding of clone GAL-13 to beta-galactosidase, rather than the silver coating. These studies suggest silver ion coated microplates are a desirable alternative to streptavidin plates for quantitative immunoassays.     

Ultra-High-Sensitive Sensor Based on Surface Plasmon Resonance Structure Having Si and Graphene Layers for the Detection of Chikungunya Virus

Chikungunya virus has been discovered in about 60 countries of the world. It leads to joint pain, joint swelling, headache, muscle pain, and fatigue of the human body. In this work, a surface plasmon resonance (SPR)based sensor is developed to detect chikungunya virus through normal and infected platelets and plasma blood cells. The proposed SPR-based sensor uses silicon and graphene layers coated over the base of a glass prism sputtered with a silver layer. The graphene layer has the advantage of enhancing the biomolecules adsorption on the metal layer. The silicon layer between silver and graphene enhances the sensor performance. The number of graphene layers along with the thicknesses of silicon and silver layers is optimized to get the highest sensitivity of the detector. To investigate the effect of the light source wavelength, simulations are performed for four different wavelengths. The highest sensitivities exhibited by the SPR-based sensor are 393 and 160 deg/RIU for the platelets and plasma cells, respectively.

     

Enhancement of Antigenic Site Detection with Gold Labeled Secondary and Tertiary Antibodies Using the Immunogold-Silver Staining Method

We report a modification of the immunogold-silver staining method (IGSS) for localizing hepatic phosphoenolpyruvate carboxykinase (PEPCK) in tissue sections, and we compare the efficacy of localizing the primary antibody with either a 5 nm gold labeled secondary antibody or 5 nm gold labeled secondary and tertiary antibodies. Light microscope examination of 10 μm frozen sections demonstrated that the use of combined secondary and tertiary gold labeled antibodies was superior to using a secondary gold labeled antibody alone. The increased labeling density (number of colloidal gold particles/antigenic site/cell) achieved by combined gold labeled antibodies was confirmed by electron microscopy. The increased labeling density resulted in a two-thirds reduction in the time needed for the IGSS physical development of the silver shells and less background. We achieved intense specific staining of hepatocytes expressing PEPCK while minimizing background staining. The use of combined secondary and tertiary gold labeled antibodies enhances the signal-to-noise ratio, achieves high resolution and is a suitable method for use in both light and electron microscopy.     

In Situ Optical Extinction Measurement for Locally Control of Surface Plasmon Resonance During Nanosecond Laser Irradiation of Silver Ion Exchanged Silicate Glass

Online UV/visible extinction measurement have been achieved during nanosecond Nd:YAG laser irradiation at 532 nm of a silver-exchanged silicate glass after each shot. We have explained the evolution of the integrated spectral evolution with the help of a few observed spots after the laser/glass interaction and completed them by optical and surface measurements. This optical method allows to in situ follow silver ions precipitation in nanoparticles (NPs) and the consequently surface plasmon resonance evolution (SPR). In this study, we focus on the interest of this method for one silver-exchanged soda-lime glass by direct observation of the sample surface. Scanning electron microscopy measurement and optical microscopy were used to identify the various ablation mechanisms. Profilometry was used to evaluate the material distribution and the surface roughness evolution (Rms parameter). Thus, we explain the silver NPs effect on glass matrix at various micrometric scales according to the deposited fluence and silver concentration.