Electrochemiluminescence of CdSe quantum dots for immunosensing of human prealbumin

We describe a non-labeled electrochemiluminescence (ECL) immunosensor based on CdSe quantum dots (QDs) for the detection of human prealbumin (PAB, antigen). The immunosensor was fabricated by layer by layer coupled with nanoparticle-amplification techniques. After two gold nanoparticle layers were self-assembled onto the gold electrode surface through cysteamine, anti-PAB (antibody) were conjugated with -COOH groups of both the CdSe QDs and cysteine, which were linked to the gold nanoparticle-modified electrode. The principle of ECL detection was that the immunocomplex inhibited the ECL reaction between CdSe QDs and K(2)S(2)O(8), which resulted in the decrease of ECL intensity. On the one hand, the immunocomplex increased the steric hindrance. On the other hand, the immunocomplex maybe inhibit the transfer of K(2)S(2)O(8) to the surface of the CdSe QD-electrode. The PAB concentration was determined in the range of 5.0 x 10(-10) to 1.0 x 10(-6) g mL(-1), and the detection limit was 1.0 x 10(-11) g mL(-1). The developed CdSe QD-based ECL immunosensor provides a rapid, simple, and sensitive immunoassay protocol for protein detection, which could be applied in more bioanalytical systems.     

Highly selective trapping of enteropathogenic E. coli on Fabry-Pérot sensor mirrors

A novel strategy for the enhancement of electrochemiluminescence (ECL) was developed by combining CdSe quantum dots (QDs) with graphene oxide-chitosan (GO-CHIT). The ECL sensor fabricated with CdSe QDs/GO-CHIT composite exhibited high ECL intensity, good biocompatibility and long-term stability, and was used to detect of cytochrome C (Cyt C). The results show that the ECL sensor has high sensitivity for Cyt C with the linear range from 4.0 to 324 μM and the detection limit of 1.5 μM. Furthermore, the ECL sensor can selectively sense Cyt C from glucose and bovine serum albumin (BSA).     

Enhanced electrochemiluminescence from reduced graphene oxide–CdTe quantum dots for highly selective determination of copper ion

An electrochemiluminescence (ECL) sensor based on reduced graphene oxide–CdTe quantum dots (RGO–CdTe QDs) composites for detecting copper ion (Cu²⁺) was proposed. The ECL behaviours of the RGO–CdTe QD modified electrode were investigated with H₂O₂ as the co‐reactant. Quantitative detection of Cu²⁺ was realized as Cu²⁺ could effectively quench the ECL signal of the RGO–CdTe QDs. A wide linear range of 1.00 × 10^?14 to 1.00 × 10^?4 M (R = 0.9953) was obtained under optimized conditions, and a detection limit (S/N = 3) was achieved of as low as 3.33 × 10^?15 M. The proposed sensor also exhibited good stability and selectivity for the detection of copper ions. Finally, the analytical application of the proposed sensor was also evaluated using river water.     

Study on the interaction between 2‐mercaptoethanol,dimercaprol and CdSe quantum dots

The interactions between 2‐mercaptoethanol, dimercaprol and CdSe quantum dots (QDs) in organic media have been investigated by spectral methods. The results showed that the fluorescence (FL) emission of CdSe QDs gradually decreased, with a slight red‐shift, after adding thiols to CdSe QDs solutions. With the increase of the concentrations of thiols, the resonance light scattering (RLS) signal of CdSe QDs had been strongly enhanced in the wavelength range 300–500 nm, which was confirmed by the formation of larger CdSe QDs particles. The effect of thiols on the FL emission of CdSe QDs could be described by a Stern–Volmer‐type equation with the concentration ranges 1.0 × 10^–6–7.5 × 10^–4 mol/L for 2‐mercaptoethanol and 1.0 × 10^–7–2.5 × 10^–5 mol/L for dimercaprol. The possible mechanism of the interaction was proposed according to the results of UV‐vis absorption and micro‐Raman spectroscopy. The results indicated that FL quenching was mainly attributable to the exchange of the QDs surface molecules. Copyright © 2008 John Wiley & Sons, Ltd.     

Development of a quantum dot molecularly imprinted polymer sensor for fluorescence detection of atrazine

Atrazine is a common agricultural pesticide which has been reported to occur widely in surface drinking water, making it an environmental pollutant of concern. In the quest for developing sensitive detection methods for pesticides, the use of quantum dots (QDs) as sensitive fluorescence probes has gained momentum in recent years. QDs have attractive and unique optical properties whilst coupling of QDs to molecularly imprinted polymers (MIPs) has been shown to offer excellent selectivity. Thus, the development of QD@MIPs based fluorescence sensors could provide an alternative for monitoring herbicides like atrazine in water. In this work, highly fluorescent CdSeTe/ZnS QDs were fabricated using the conventional organometallic synthesis approach and were then encapsulated with MIPs. The CdSeTe/ZnS@MIP sensor was characterized and applied for selective detection of atrazine. The sensor showed a fast response time (5 min) upon interaction with atrazine and the fluorescence intensity was linearly quenched within the 2–20 mol L^?1 atrazine range. The detection limit of 0.80 × 10^?7 mol L^?1 is comparable to reported environmental levels. Lastly, the sensor was applied in real water samples and showed satisfactory recoveries (92–118%) in spiked samples, hence it is a promising candidate for use in water monitoring.     

An ultrasensitive electrochemiluminescent sensor based on a pencil graphite electrode modified with CdS nanorods for detection of chlorogenic acid in honeysuckle

In this paper, a novel and ultrasensitive electrochemiluminescent sensor employing a solvothermal‐synthesized CdS nanorod‐modified pencil graphite electrode (CdS/PGE) for the determination of chlorogenic acid (CA) is fabricated. In the first step, the PGE surface is modified using CdS nanorods. In the next step, the developed electrode is used to detect CA using a electrochemiluminescent (ECL) technique, in which potassium persulfate (K₂S₂O₈) served as a co‐reactant. The possible ECL mechanism is investigated, and the influences of pH and cyclic voltammetric scanning rate on the signal response are studied. The ECL intensity decreases quantitatively in relation to the concentration of the target molecule. Under optimized conditions, the linear correlation between the quenched ECL intensity and the logarithm of CA concentration is observed in the range from 2 × 10^?9 to 8 × 10^?7 mol L^?1 with a limit of detection of 1 × 10^?9 mol L^?1. This proposed method is applied to the analysis of CA in honeysuckle flower, giving recoveries of 99‐107%. The experimental results demonstrate that this ECL sensor shows good stability and reproducibility.     

Graphene‐amplified electrogenerated chemiluminescence of CdTe quantum dots for H2O2 sensing

Electrogenerated chemiluminescence (ECL) of thiol‐capped CdTe quantum dots (QDs) in aqueous solution was greatly enhanced by PDDA‐protected graphene (P‐GR) film that were used for the sensitive detection of H₂O₂. When the potential was cycled between 0 and ?2.3 V, two ECL peaks were observed at ?1.1 (ECL‐1) and ?1.4 V (ECL‐2) in pH 11.0, 0.1 M phosphate buffer solution (PBS), respectively. The electron‐transfer reaction between individual electrochemically‐reduced CdTe nanocrystal species and oxidant coreactants (H₂O₂ or reduced dissolved oxygen) led to the production of ECL‐1. While mass nanocrystals packed densely in the film were reduced electrochemically, assembly of reduced nanocrystal species reacted with coreactants to produce an ECL‐2 signal. ECL‐1 showed higher sensitivity for the detection of H₂O₂ concentrations than that of ECL‐2. Further, P‐GR film not only enhanced ECL intensity of CdTe QDs but also decreased its onset potential. Thus, a novel CdTe QDs ECL sensor was developed for sensing H₂O₂. Light intensity was linearly proportional to the concentration of H₂O₂ between 1.0 × 10^?5 and 2.0 x 10^‐7 mol L^?1 with a detection limit of 9.8 x 10^?8 mol L^?1. The P‐GR thin‐film modified glassy carbon electrode (GCE) displayed acceptable reproducibility and long‐term stability. Copyright © 2012 John Wiley & Sons, Ltd.     

A chiral,porous, organic cage‐based,enantioselective potentiometric sensor for 2‐aminobutanol

A new enantioselective potentiometric sensor containing R‐type chiral porous organic cage CC9 as the chiral selector was designed for the assay of 2‐aminobutanol. Optimized membrane electrodes displayed a linear dynamic range from 10⁻³ ~ 10⁻¹ mol·L⁻¹ with a detection limit of 2.5 × 10⁻⁴ mol·L⁻¹ and a Nernstian response of 27 ± 0.5mV·decade⁻¹ toward S‐2‐aminobutanol within the pH range 7.0–10.0. The potentiometric enantioselectivity coefficient ( ) of this sensor was −1.333, indicating that the porous organic cage‐based electrode exhibited good discrimination toward S‐2‐aminobutanol over R‐2‐aminobutanol.     

Sensitive determination of carbidopa through the electrochemiluminescence of luminol at graphene‐modified electrodes

Using the concept of electrogenerated chemiluminescence (ECL), a sensitive analytical method for the determination of carbidopa is described. Electro‐oxidation of carbidopa on the surface of a graphene oxide (GO)‐modified gold electrode (GE) leads to enhancement of the weak emission of oxidized luminol. Under optimum experimental conditions, the ECL signal increases linearly with increasing carbidopa concentrations over a range of 1.0 × 10^‐9–1.7 × 10^‐7 M, with a detection limit of 7.4 × 10^‐10 M. The proposed ECL method was successfully used for the determination of carbidopa in urine samples. Copyright © 2014 John Wiley & Sons, Ltd.     

Molecularly imprinted polyaniline molecular receptor–based chemical sensor for the electrochemical determination of melamine

Molecularly imprinted polymer‐modified glassy carbon electrode (GCE)‐based electrochemical sensor is prepared using the electropolymerization of aniline in the presence of melamine (MA) as a template. In this work, the advantages of molecularly imprinted conducting polymers (MICPs) and electroanalytical methods were combined to obtain an electronic device with better performances. The sensor performance was evaluated by cyclic voltammetry (CV) and square wave voltammetry (SWV) with the linear range of 0.6‐16 × 10^?9M, quantification limit of 14.9 × 10^?10M, and detection limit of 4.47 × 10^?10M (S/N = 3). The selectivity of the sensor was tested in the presence of acetoguanamine (AGA), diaminomethylatrazine (DMT), casein, histidine, and glycine interfering molecules taken at the triple concentration with MA that demonstrated too small current response compared with that of the analyte indicating high specificity of the sensor towards the template. The sensor was successfully applied to determine MA in infant formula samples with significant recovery greater than 96% and relative standard deviation (RSD) less than 4.8%. Moreover, the good repeatability, recyclability, and stability make this sensor device promising for the real‐time monitoring of MA in different food stuffs.     

Epitope imprinting of iron binding protein of Neisseria meningitidis bacteria through multiple monomers imprinting approach

Epitope imprinting is a promising technique for fabrication of novel diagnostic tools. In this study, an epitope imprinted methodology for recognition of target epitope sequence as well as targeted protein infused by bacterial infection in blood samples of patients suffering from brain fever is developed. Template sequence chosen is a ferric iron binding fbp A protein present in Neisseria meningitidis bacteria. To orient the imprinting template peptide sequence on gold surface of electrochemical quartz crystal microbalance (EQCM), thiol chemistry was utilized to form the self‐assembled monolayer on EQCM electrode. Here, synergistic effects induced by various noncovalent interactions extended by multiple monomers (3‐sulfopropyl methacrylate potassium‐salt and benzyl methacrylate) were used in fabricating the imprinting polymeric matrix with additional firmness provided by N,N‐methylene‐bis‐acrylamide as cross‐linker and azo‐isobutyronitrile as initiator. Extraction of template molecule was carried out with phosphate buffer solution. After extraction of epitope molecules from the polymeric film, epitope molecularly imprinted polymeric films were fabricated on EQCM electrode surface. Nonimprinted polymers were also synthesized in the similar manner without epitope molecule. Detection limit of epitope molecularly imprinted polymers and imprinting factor (epitope molecularly imprinted polymers/nonimprinted polymers) was calculated 1.39 ng mL^?1 and 12.27 respectively showing high binding capacity and specific recognition behavior toward template molecule. Simplicity of present method would put forward a fast, facile, cost‐effective diagnostic tool for mass health care.     

A sensitive electrochemiluminescent sensor chip based on the ssDNA-Ru(II) complex and aptamer for the determination of thrombin

In this work, an electrochemiluminescence (ECL) sensor chip for sensitive detection of thrombin (TB) was prepared using a screen-printed electrode (SPE) as a working electrode and an aptamer as a specific recognition moiety. To produce an ECL sensor chip, a layer of pL-Cys was immobilized on the surface of the SPE using the cyclic voltammetry scanning method. A layer of gold nanoparticles (AuNPs) was assembled through an Au–S bond and hairpin DNA was further immobilized on the electrode surface. Ru(bpy)₂(mcpbpy)²⁺, as a luminescent reagent, was covalently bound to single-stranded DNA (ssDNA) to prepare a luminescence probe ssDNA-Ru. The probe was hybridized with TB aptamer to form a capture probe. In the presence of TB, the TB aptamer in the capture probe bound to TB, causing the release of ssDNA-Ru that could bind to hairpin DNA on the electrode surface. The Ru(II) complex as a luminescent reagent was assembled onto the electrode, and pL-Cys was used as a co-reactant to enhance the ECL efficiency. The ECL signal of the sensor chip generated based on the above principles had a linear relationship with log TB concentration at the range 10 fM to1 nM, and the detection limit was 0.2 fM. Finally, TB detection using this method was verified using real blood samples. This work provides a new method using an aptamer as a foundation and SPE as a material for the detection of biological substances.     

Preparation of water‐soluble CdSe quantum dots and its application for nitrite detection in the anodic electrochemiluminescence

Water‐soluble CdSe quantum dots (QDs) have been prepared by using L‐cysteine as the stabilizer in an aqueous phase under the optimized conditions. The characteristics and shapes of CdSe QDs have been proposed on the basis of UV‐Vis and fluorescence spectra. A rapid analytical method for electrochemiluminescence (ECL) determination of nitrite has been developed on the basis of the quenching effect on anodic ECL emission of CdSe QDs under the optimum experimental conditions. In a neutral system and at a relatively low potential (+0.960 V), the ECL emission of CdSe QDs could be greatly enhanced by sulfite and could be gradually quenched by nitrite at an indium tin oxide (ITO) electrode. The proposed method may allow the measurement of nitrite ranging from 1 μM to 0.5 mM with a correlation coefficient of 0.9956 (n = 10) and a detection limit of 0.2 μM (3σ), and the relative standard deviation for 10 μM nitrite (n = 9) is 1.72 %. The proposed method could be adopted for the sensitive detection of ECL quenchers by using nitrite as a model molecule. Copyright © 2013 John Wiley & Sons, Ltd.     

Chiral determination of cinchonine using an electrochemiluminescent sensor with molecularly imprinted membrane on the surfaces of magnetic particles

A novel molecular imprinting electrochemiluminescence sensor for detecting chiral cinchonine molecules was developed with a molecularly imprinted polymer membrane on the surfaces of magnetic microspheres. Fe₃O₄@Au nanoparticles modified with 6‐mercapto‐beta‐cyclodextrin were used as a carrier, cinchonine as a template molecule, methacrylic acid as a functional monomer and N ,N ′‐methylenebisacrylamide as a cross‐linking agent. Cinchonine was specifically recognized by the 6‐mercapto‐beta‐cyclodextrin functional molecularly imprinted polymer and detected based on enhancement of the electrochemiluminescence intensity caused by the reaction of tertiary amino structures of cinchonine molecules with Ru(bpy)₃²⁺. Cinchonine concentrations of 1 × 10^?10 to 4 × 10^?7 mol/L showed a good linear relationship with changes of the electrochemiluminescence intensity, and the detection limit of the sensor was 3.13 × 10^?11 mol/L. The sensor has high sensitivity and selectivity, and is easy to renew. It was designed for detecting serum samples, with recovery rates of 98.2% to 107.6%.     

Electrochemical sensor based on gold nanoparticles fabricated molecularly imprinted polymer film at chitosan-platinum nanoparticles/graphene-gold nanoparticles double nanocomposites modified electrode for detection of erythromycin

A molecularly imprinted electrochemical sensor was fabricated based on gold electrode decorated by chitosan-platinum nanoparticles (CS-PtNPs) and graphene-gold nanoparticles (GR-AuNPs) nanocomposites for convenient and sensitive determination of erythromycin. The synergistic effects of CS-PtNPs and GR-AuNPs nanocomposites improved the electrochemical response and the sensitivity of the sensor. The molecularly imprinted polymers (MIPs) were prepared by HAuCl(4), 2-mercaptonicotinic acid (MNA) and erythromycin. Erythromycin and MNA were used as template molecule and functional monomer, respectively. They were first assembled on the surface of GR-AuNPs/CS-PtNPs/gold electrode by the formation of Au-S bonds and hydrogen-bonding interactions. Then the MIPs were formed by electropolymerization of HAuCl(4), MNA and erythromycin. The sensor was characterized by cyclic voltammetry (CV), scanning electron microscope (SEM), UV-visible (UV-vis) absorption speactra and amperometry. The linear range of the sensor was from 7.0×10(-8)mol/L-9.0×10(-5)mol/L, with the limit of detection (LOD) of 2.3×10(-8)mol/L (S/N=3). The sensor showed high selectivity, excellent stability and good reproducibility for the determination of erythromycin, and it was successfully applied to the detection of erythromycin in real spiked samples.     

Electrochemical and piezoelectric monitoring of taurine via electropolymerized molecularly imprinted films

A molecularly imprinted electrochemical quartz crystal microbalance (EQCM) sensor is fabricated here for taurine, a β ‐amino acid significant for functioning of almost all vital organs. The polymeric film of l ‐methionine was electrochemically deposited on gold‐coated EQCM electrode. Experimental parameters were optimized for controlling the performance of molecularly imprinted polymer (MIP)‐modified sensor such as ratio of monomer and template, number of electropolymerization cycles, mass deposited in each cycle, and pH. Thus, fabricated MIP‐EQCM sensor was successfully applied for estimation of taurine in solutions with varying matrices, such as aqueous, human blood plasma, milk from cow, buffalo, and milk powder. Under optimized parameters, response of MIP sensor to taurine was linearly proportional to its concentration with limit of detection as 0.12μM. Hence, a highly sensitive and selective piezoelectric sensor for taurine has been reported here via imprinting approach.     

Electrogenerated chemiluminescence of ruthenium complex immobilized in a highly cross‐linked polymer and its analytical applications

Electrogenerated chemiluminescence (ECL) of a ruthenium complex polymer modified carbon paste electrode and its analytical applications were investigated. The ruthenium complex polymer was prepared using bis(2,2‐bipyridine) (4,4‐dicarboxy‐2,2‐bipyridine) ruthenium(II). The ECL behaviours of ruthenium complex polymer modified carbon paste electrode were investigated in the absence and presence of tripropylamine (TPA). The modified carbon paste electrode exhibited long‐term stability and fine reproducibility. The ECL intensity of the modified carbon paste electrode was linear with the concentration of TPA in the range 2.0 × 10^–6–3.8 × 10^–3 mol/L, with a detection limit (S:N = 3) of 6 × 10^–7 mol/L. It was also found that raceanisodamine could enhance the ECL intensity of the modified electrode. The ECL intensity of the modified carbon paste electrode was linear with the concentration of raceanisodamine in the range 1.1 × 10^–5–6.0 × 10^–4 mol/L, with a detection limit (S:N = 3) of 6 × 10^–6 mol/L. This work demonstrates that the entrapment of ruthenium complex in a highly cross‐linked polymer is a promising approach to construct an ECL modified electrode with long‐term stability and fine reproducibility. The modified electrode designed has a potential application in the ECL detector. Copyright © 2008 John Wiley & Sons, Ltd.     

Flow injection analysis of thiamazole based on strong Ru(bpy)32+ co‐reactant electrochemiluminescence

Based on the strong electrochemiluminescence (ECL) reaction between thiamazole and tris(2,2′‐bipyridine)ruthenium(II) (Ru(bpy)₃²⁺), a sensitive, simple and rapid flow injection analysis method for the determination of thiamazole was developed. When a Pt working electrode was maintained at a potential of +1.50 V (vs Ag/AgCl) in pH 12.0 H₃PO₄–NaOH solution containing thiamazole and Ru(bpy)₃²⁺ at a flow rate of 1.0 mL/min, a linear range of 2.0 × 10⁻⁷–1.0 × 10⁻⁴ mol/L with a detection limit of 5.0 × 10⁻⁸ mol/L was obtained for the detection of thiamazole. The method showed good reproducibility with a relative standard deviation (RSD) of 0.75%. The method has been successfully applied to the determination of thiamazole in spiked animal feeds. In addition, a co‐reactant ECL mechanism was proposed for the thiamazole–Ru(bpy)₃²⁺ system. Copyright © 2014 John Wiley & Sons, Ltd.     

Highly sensitive protein kinase activity assay based on electrochemiluminescence nanoprobes

Herein, we describe a novel electrochemiluminescence (ECL) biosensor for protein kinase activities and inhibition monitoring based on the magnetic beads (MB) technology and signal enhancement of gold nanoparticles (GNP). In this design, ECL nanoprobes were prepared by conjugating GNP with phosphorylated DNA capture probes and tris-(2,2'-bipyridyl) ruthenium (TBR)-cysteamine. Zirconium cations, a specific bridging agent, mediate the linkage between biotin modified phosphorylated peptides and ECL nanoprobes. The complexes were then captured and enriched on the electrode surface by streptavidin-coated MB for ECL reaction. To confirm the feasibility of this biosensor, we employed protein kinase A (PKA) as the model kinase to validate the assay and a satisfactory detection limit of 0.005 U/mL was achieved. The combination of ECL and GNP lays a solid foundation for highly sensitive assay, meanwhile, the coupling of MB surfaces used for separation and capture with unmodified ECL electrode detection results in a greatly simplified and reusable protocol. Thus, our biosensor offers great promise for a highly sensitive and simple assay for protein kinase activity. Furthermore, the inhibition of PKA activity was monitored on the basis of the ECL signals change in response to the concentration of PKA inhibitor.     

Electrochemiluminescence detection of methamphetamine based on a Ru(bpy)32+‐doped silica nanoparticles/Nafion composite film modified electrode

An electrochemiluminescence (ECL) approach for methamphetamine determination was developed based on a glassy carbon electrode modified with a Ru(bpy)₃²⁺‐doped silica nanoparticles/Nafion composite film. The monodispersed nanoparticles, which were about 50 nm in size, were synthesized using the water‐in‐oil microemulsion method. The ECL results revealed that Ru(bpy)₃²⁺ doped in silica nanoparticles retained its original photo‐ and electrochemical properties. The ECL intensity was found to be proportional to methamphetamine concentration over the range from 1.0 × 10^?7 to 1.0 × 10^?5 mol L^?1, and the detection limit was found to be 2.6 × 10^?8 mol L^?1. The proposed ECL approach was used to analyze the methamphetamine content in drugs. Copyright © 2009 John Wiley & Sons, Ltd.