Adaptation to high current using low external resistances eliminates power overshoot in microbial fuel cells

One form of power overshoot commonly observed with mixed culture microbial fuel cells (MFCs) is doubling back of the power density curve at higher current densities, but the reasons for this type of overshoot have not been well explored. To investigate this, MFCs were acclimated to different external resistances, producing a range of anode potentials and current densities. Power overshoot was observed for reactors acclimated to higher (500 and 5000 Ω) but not lower (5 and 50 Ω) resistances. Acclimation of the high external resistance reactors for a few cycles to low external resistance (5 Ω), and therefore higher current densities, eliminated power overshoot. MFCs initially acclimated to low external resistances exhibited both higher current in cyclic voltammograms (CVs) and higher levels of redox activity over a broader range of anode potentials (-0.4 to 0 V; vs. a Ag/AgCl electrode) based on first derivative cyclic voltammetry (DCV) plots. Reactors acclimated to higher external resistances produced lower current in CVs, exhibited lower redox activity over a narrower anode potential range (-0.4 to -0.2 V vs. Ag/AgCl), and failed to produce higher currents above ～-0.3 V (vs. Ag/AgCl). After the higher resistance reactors were acclimated to the lowest resistance they also exhibited similar CV and DCV profiles. Our findings show that to avoid overshoot, prior to the polarization and power density tests the anode biofilm must adapt to low external resistances to be capable of higher currents.     

Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells

Carbon nanotube (CNT) is a promising electrode material and has been used as an anode modifier in microbial fuel cells (MFCs). In this study, a new method of simultaneously adding CNT powders and Geobacter sulfurreducens into the anode chamber of a MFC was used, aiming to form a composite biofilm on the anode. The performance of MFCs such as startup time and steady-state power generation was investigated under conditions of different CNT powders dosages. Results showed that both the startup time and the anodic resistance were reduced. The optimal dosage of CNT powders pre-treated by acid was 4 mg/mL for the anode chamber with an effective volume of 25 mL. The anodic resistance and output voltage of the MFC with CNT powders addition were maintained around 180 Ω and 650 mV during 40 days operation, while those of the MFC without CNT powders addition increased from 250 Ω to 540 Ω and decreased from 630 mV to 540 mV, respectively, demonstrating that adding CNT powders helped stabilize the anodic resistance, thus the internal resistance and power generation during long-term operation. Based on cyclic voltammogram, the electrochemical activity of anodic biofilm was enhanced by adding CNT powders, though no significant increase of the biomass in anodic biofilm was detected by phospholipids analysis. There was no remarkable change of ohmic resistance with an addition of CNT powders revealed by current interrupt method, which indicated that the rate of mass transfer might be promoted by the presence of CNT powders.     

微生物燃料电池利用乳酸产电性能与微生物群落分布特征

【目的】为探讨以乳酸为基质的微生物燃料电池(Microbial fuel cell,MFC)产电性能以及微生物群落在阳极膜、悬浮液、阳极沉淀污泥中的分布特征,【方法】试验建立了双室MFC,以乳酸为阳极主要碳源,研究了反应器的启动过程及产电效能,同时以电镜和PCR-变性梯度凝胶电泳(Denaturing gradient gelelectrophoresis,DGGE)技术解析了微生物群落的空间分布特征。【结果】结果表明,反应器启动第7天时外电压达到0.56 V,当外阻为80Ω时,电流密度为415 mA/m2,MFC的功率密度达到最大值82 mW/m2。电镜观察发现大量杆菌附着在阳极表面,结合较为紧密;DGGE图谱显示阳极膜表面微生物与种泥最为相似,与阳极悬浮液、底部沉淀污泥中的主要菌群一致,条带序列与睾丸酮丛毛单胞菌(Comamonas testosteroni)和布氏弓形菌(Arcobacter butzleri)等最为相似。【结论】本研究表明以乳酸为基质MFC可产生较高的功率密度,阳极附着的优势菌与接种污泥来源密切相关。     

Influence of external resistance on electrogenesis, methanogenesis, and anode prokaryotic communities in microbial fuel cells

The external resistance (R(ext)) of microbial fuel cells (MFCs) regulates both the anode availability as an electron acceptor and the electron flux through the circuit. We evaluated the effects of R(ext) on MFCs using acetate or glucose. The average current densities (I) ranged from 40.5 mA/m(2) (9,800 Ω) to 284.5 mA/m(2) (150 Ω) for acetate-fed MFCs (acetate-fed reactors [ARs]), with a corresponding anode potential (E(an)) range of -188 to -4 mV (versus a standard hydrogen electrode [SHE]). For glucose-fed MFCs (glucose-fed reactors [GRs]), I ranged from 40.0 mA/m(2) (9,800 Ω) to 273.0 mA/m(2) (150 Ω), with a corresponding E(an) range of -189 to -7 mV. ARs produced higher Coulombic efficiencies and energy efficiencies than GRs over all tested R(ext) levels because of electron and potential losses from glucose fermentation. Biogas production accounted for 14 to 18% of electron flux in GRs but only 0 to 6% of that in ARs. GRs produced similar levels of methane, regardless of the R(ext). However, total methane production in ARs increased as R(ext) increased, suggesting that E(an) might influence the competition for substrates between exoelectrogens and methanogens in ARs. An increase of R(ext) to 9,800 Ω significantly changed the anode bacterial communities for both ARs and GRs, while operating at 970 Ω and 150 Ω had little effect. Deltaproteobacteria and Bacteroidetes were the major groups found in anode communities in ARs and GRs. Betaproteobacteria and Gammaproteobacteria were found only in ARs. Bacilli were abundant only in GRs. The anode-methanogenic communities were dominated by Methanosaetaceae, with significantly lower numbers of Methanomicrobiales. These results show that R(ext) affects not only the E(an) and current generation but also the anode biofilm community and methanogenesis.     

Comparison of anode bacterial communities and performance in microbial fuel cells with different electron donors

Microbial fuel cells (MFCs) harness the electrochemical activity of certain microbes for the production of electricity from reduced compounds. Characterizations of MFC anode biofilms have collectively shown very diverse microbial communities, raising ecological questions about competition and community succession within these anode-reducing communities. Three sets of triplicate, two-chamber MFCs inoculated with anaerobic sludge and differing in energy sources (acetate, lactate, and glucose) were operated to explore these questions. Based on 16S rDNA-targeted denaturing gradient gel electrophoresis (DGGE), all anode communities contained sequences closely affiliated with Geobacter sulfurreducens (>99% similarity) and an uncultured bacterium clone in the Bacteroidetes class (99% similarity). Various other Geobacter-like sequences were also enriched in most of the anode biofilms. While the anode communities in replicate reactors for each substrate generally converged to a reproducible community, there were some variations in the relative distribution of these putative anode-reducing Geobacter-like strains. Firmicutes were found only in glucose-fed MFCs, presumably serving the roles of converting complex carbon into simple molecules and scavenging oxygen. The maximum current density in these systems was negatively correlated with internal resistance variations among replicate reactors and, likely, was only minimally affected by anode community differences in these two-chamber MFCs with high internal resistance.     

Power output and columbic efficiencies from biofilms of Geobacter sulfurreducens comparable to mixed community microbial fuel cells

It has been previously noted that mixed communities typically produce more power in microbial fuel cells than pure cultures. If true, this has important implications for the design of microbial fuel cells and for studying the process of electron transfer on anode biofilms. To further evaluate this, Geobacter sulfurreducens was grown with acetate as fuel in a continuous flow 'ministack' system in which the carbon cloth anode and cathode were positioned in close proximity, and the cation-selective membrane surface area was maximized in order to overcome some of the electrochemical limitations that were inherent in fuel cells previously employed for the study of pure cultures. Reducing the size of the anode in order to eliminate cathode limitation resulted in maximum current and power densities per m(2) of anode surface of 4.56 A m(-2) and 1.88 W m(-2) respectively. Electron recovery as current from acetate oxidation was c. 100% when oxygen diffusion into the system was minimized. This performance is comparable to the highest levels previously reported for mixed communities in similar microbial fuel cells and slightly higher than the power output of an anaerobic sludge inoculum in the same ministack system. Minimizing the volume of the anode chamber yielded a volumetric power density of 2.15 kW m(-3), which is the highest power density per volume yet reported for a microbial fuel cell. Geobacter sulfurreducens formed relatively uniform biofilms 3-18 mum thick on the carbon cloth anodes. When graphite sticks served as the anode, the current density (3.10 A m(-2)) was somewhat less than with the carbon cloth anodes, but the biofilms were thicker (c. 50 mum) with a more complex pillar and channel structure. These results suggest that the previously observed disparity in power production in pure and mixed culture microbial fuel cell systems can be attributed more to differences in the fuel cell designs than to any inherent superior capability of mixed cultures to produce more power than pure cultures.     

Layer-by-layer construction of graphene-based microbial fuel cell for improved power generation and methyl orange removal

Development of highly efficient anode is critical for enhancing the power output of microbial fuel cells (MFCs). The aim of this work is to investigate whether modification of carbon paper (CP) anode with graphene (GR) via layer-by-layer assembly technique is an effective approach to promote the electricity generation and methyl orange removal in MFCs. Using cyclic voltammetry and electrochemical impedance spectroscopy, the GR/CP electrode exhibited better electrochemical behavior. Scanning electron microscopy results revealed that the surface roughness of GR/CP increased, which was favorable for more bacteria to attach to the anode surface. The MFCs equipped with GR/CP anode achieved a stable maximum power density of 368 mW m^?2 under 1,000 Ω external resistance and a start time for the initial maximum voltage of 180 h, which were, respectively, 51 % higher and 31 % shorter than the corresponding values of the MFCs with blank anode. The anode and cathode polarization curves revealed negligible difference in cathode potentials but obviously difference in anode potentials, indicating that the GR-modified anode other than the cathode was responsible for the performance improvement of MFC. Meanwhile, compared with MFCs with blank anode, 11 % higher decolorization efficiency and 16 % higher the chemical oxygen demand removal rate were achieved in MFC with GR-modified anode during electricity generation. This study might provide an effective way to modify the anode for enhanced electricity generation and efficient removal of azo dye in MFCs.     

Anode microbial communities produced by changing from microbial fuel cell to microbial electrolysis cell operation using two different wastewaters

Conditions in microbial fuel cells (MFCs) differ from those in microbial electrolysis cells (MECs) due to the intrusion of oxygen through the cathode and the release of H₂ gas into solution. Based on 16S rRNA gene clone libraries, anode communities in reactors fed acetic acid decreased in species richness and diversity, and increased in numbers of Geobacter sulfurreducens, when reactors were shifted from MFCs to MECs. With a complex source of organic matter (potato wastewater), the proportion of Geobacteraceae remained constant when MFCs were converted into MECs, but the percentage of clones belonging to G. sulfurreducens decreased and the percentage of G. metallireducens clones increased. A dairy manure wastewater-fed MFC produced little power, and had more diverse microbial communities, but did not generate current in an MEC. These results show changes in Geobacter species in response to the MEC environment and that higher species diversity is not correlated with current.     

On the dynamic response of the anode in microbial fuel cells

A study of the dynamic response of a microbial fuel cell (MFC) using membrane electrode assemblies (MEAs) designed for air breathing cathode operation is reported. The MFC used four MEAs simultaneously and has a low internal resistance. An increased concentration of glucose produced a non-linear increase in the maximum current reached. The time to reach the maximum current increased with increasing glucose concentrations of 1-7 mM; varying from approximately 2.4 to 4.2h. The rate at which the current density increased with time was the same for all glucose concentrations up to current densities close to the maximum values. The peak power density varied approximately linearly with glucose concentrations from 2 to 77 mW/m(2) (1-7 mM) with a 1 kΩ resistance. The cell response appeared to be linked to a slow process of fuel transport to the bacteria and their metabolic processes. The dynamic response of the anode was analysed in terms of a substrate mass transport model. The application of different current ranges did not significantly change the dynamic response of either the anode community or the MFC polarization characteristics. Thus, it is likely that the bacterial communities that form under MFC operation contain sufficiently "dominant" electro-active species that are capable of producing high power for MFCs.     

Electrochemical surface modification of carbon mesh anode to improve the performance of air-cathode microbial fuel cells

A convenient and promising alternative to surface modification of carbon mesh anode was fulfilled by electrochemical oxidation in the electrolyte of nitric acid or ammonium nitrate at ambient temperature. It was confirmed that such an anode modification method was low cost and effective not only in improving the efficiency of power generation in microbial fuel cells (MFCs) for synthetic wastewater treatment, but also helping to reduce the period for MFCs start-up. The MFCs with anode modification in electrolyte of nitric acid performed the best, achieving a Coulombic efficiency enhancement of 71 %. As characterized, the electrochemical modification resulted in the decrease of the anode potential and internal resistance but the increase of current response and nitrogen-containing and oxygen-containing functional groups on the carbon surface, which might contribute to the enhancement on the performances of MFCs.     

Change in microbial communities in acetate- and glucose-fed microbial fuel cells in the presence of light

Power densities produced by microbial fuel cells (MFCs) in natural systems are changed by exposure to light through the enrichment of photosynthetic microorganisms. When MFCs with brush anodes were exposed to light (4000 lx), power densities increased by 8–10% for glucose-fed reactors, and 34% for acetate-fed reactors. Denaturing gradient gel electrophoresis (DGGE) profiles based on the 16S rRNA gene showed that exposure to high light levels changed the microbial communities on the anodes. Based on 16S rRNA gene clone libraries of light-exposed systems the anode communities using glucose were also significantly different than those fed acetate. Dominant bacteria that are known exoelectrogens were identified in the anode biofilm, including a purple nonsulfur (PNS) photosynthetic bacterium, Rhodopseudomonas palustris, and a dissimilatory iron-reducing bacterium, Geobacter sulfurreducens. Pure culture tests confirmed that PNS photosynthetic bacteria increased power production when exposed to high light intensities (4000 lx). These results demonstrate that power production and community composition are affected by light conditions as well as electron donors in single-chamber air-cathode MFCs.     

Electricity generation from polyalcohols in single-chamber microbial fuel cells

Six polyalcohols derived from lignocellulosic carbohydrates were investigated as carbon sources for electricity generation in single-chamber mediator-less microbial fuel cells (MFCs) for the first time. Electricity was directly generated from all polyalcohols tested, including pentitols (xylitol, arabitol, and ribitol) and hexitols (galactitol, mannitol, and sorbitol). Bacterial cultures initially enriched using acetate could be adapted to these substrates with varied adaptation times. The resultant maximum power density ranged from 1490+/-160 mW/m(2) to 2650+/-10 mW/m(2) at current densities between 0.58 mA/cm(2) and 0.78 mA/cm(2). Galactitol generated the highest maximum power density, while mannitol resulted in the lowest one. The estimated maximum voltage output at an external resistance of 120 Omega ranged between 0.24 V and 0.34 V with half saturation kinetic constants varied from 298 mg/L to 753 mg/L. The removal of chemical oxygen demand (COD) was above 91% for all polyalcohols except sorbitol (71%). Denaturing gradient gel electrophoresis (DGGE) of PCR-amplified 16S rRNA gene segments of the anode biofilms showed the influence of substrates (polyalcohols) on the anode microbial populations.     

Microbial fuel cells meet with external resistance

The influence of external load on the composition of the anodic biofilm microbial community and biomass yield was investigated in a microbial fuel cell fed with glucose and domestic wastewater was used as source of electrogens. Denaturing gradient gel electrophoresis (DGGE) of polymerase chain reaction (PCR) amplified 16S rRNA gene fragments revealed distinct differences in anodic bacterial communities formed at the anode of each MFC operated under a different external load. These results implied that in an MFC, electrogenic bacteria were enriched under higher current densities, i.e., low external load, and were able to sustain better current and effluent quality. The influence of the external resistance applied to the MFCs during formation of the bacterial communities from sewage wastewater was shown to have no significant effect on power performance of the MFCs nor to have a significant influence on their anodic activity with both glucose and brewery wastewater as fuel. As expected, current generation, COD removal and the biomass yield were all directly influenced by the external load. Significantly, when operated under lower external load, the biomass yield in the MFC was less than that in conventional anaerobic digestion (i.e., control).     

Long-term cathode performance and the microbial communities that develop in microbial fuel cells fed different fermentation endproducts

To better understand how cathode performance and substrates affected communities that evolved in these reactors over long periods of time, microbial fuel cells were operated for more than 1 year with individual endproducts of lignocellulose fermentation (acetic acid, formic acid, lactic acid, succinic acid, or ethanol). Large variations in reactor performance were primarily due to the specific substrates, with power densities ranging from 835 ± 21 to 62 ± 1 mW/m³. Cathodes performance degraded over time, as shown by an increase in power of up to 26% when the cathode biofilm was removed, and 118% using new cathodes. Communities that developed on the anodes included exoelectrogenic families, such as Rhodobacteraceae, Geobacteraceae, and Peptococcaceae, with the Deltaproteobacteria dominating most reactors. Pelobacter propionicus was the predominant member in reactors fed acetic acid, and it was abundant in several other MFCs. These results provide valuable insights into the effects of long-term MFC operation on reactor performance.     

Effects of the Pt loading side and cathode-biofilm on the performance of a membrane-less and single-chamber microbial fuel cell

In order to analyze the effect of cathode's Pt loading side on the performance of single-chamber microbial fuel cells (MFCs), power generation of a bamboo charcoal membrane-less air-cathode MFC was examined. The maximum power outputs obtained were 0.144 and 1.16 mW, while the maximum voltage outputs were 0.400 and 0.500 V (external resistance was 500 Omega), respectively, when the Pt loading side facing to the air and to the anode chamber solution; after a long time of operation with the side of cathode loaded Pt facing to anode chamber solution, a biofilm was developed on the inner side of cathode. With the formation of this biofilm, the power outputs of MFC increased first, and then decreased to 0.8 mW; oxidation-reduction potentials (ORP) dropped first, and then achieved the level of stability. Coulombic efficiency (CE) increased at a certain extent. In addition, the impact of cathode-biofilm on the loss of water in anode chamber solution was determined.     

Dynamic changes in the microbial community composition in microbial fuel cells fed with sucrose

The performance and dynamics of the bacterial communities in the biofilm and suspended culture in the anode chamber of sucrose-fed microbial fuel cells (MFCs) were studied by using denaturing gradient gel electrophoresis (DGGE) of PCR-amplified partial 16S rRNA genes followed by species identification by sequencing. The power density of MFCs was correlated to the relative proportions of species obtained from DGGE analysis in order to detect bacterial species or taxonomic classes with important functional role in electricity production. Although replicate MFCs showed similarity in performance, cluster analysis of DGGE profiles revealed differences in the evolution of bacterial communities between replicate MFCs. No correlation was found between the proportion trends of specific species and the enhancement of power output. However, in all MFCs, putative exoelectrogenic denitrifiers and sulphate-reducers accounted for approximately 24% of the bacterial biofilm community at the end of the study. Pareto–Lorenz evenness distribution curves extracted from the DGGE patterns obtained from time course samples indicated community structures where shifts between functionally similar species occur, as observed within the predominant fermentative bacteria. These results suggest the presence of functional redundancy within the anodic communities, a probable indication that stable MFC performance can be maintained in changing environmental conditions. The capability of bacteria to adapt to electricity generation might be present among a wide range of bacteria.     

Biocathode microbial fuel cell for efficient electricity recovery from dairy manure

Microbial fuel cells (MFCs) represent a new biological method for generating electricity directly from biodegradable compounds. Efficiency of MFCs using manure as substrate is generally low. This study proposed a new design by incorporating biocathodes into a three-chamber MFC, which yielded maximum power densities much higher than those reported in literature. The new design placed cylindrical anode chamber for easy stirring and two symmetrical cathodic chambers with reduced anode-cathode distance. The biocathodes were applied to reduce charge transfer resistance. Additionally, biocathode microbial community was cultured to enrich favorable microorganisms. With external loading of 100 Ω, the power densities for new biocathode MFC using 2, 4, 6, 8 and 10% total solids diary manure reached 7.85±1.0 W m(-3), 7.84±1.20 W m(-3), 8.15±0.20 W m(-3), 7.60±0.97 W m(-3) and 5.63±0.97 W m(-3), respectively. The pH drop as a result of manure hydrolysis limited the power output. To provide detailed information of the microbial community in the biocathode MFC, the 454-pyrosequencing technique was adopted. The Firmicutes, γ-, β-, α- and δ-Proteobacteria, Bacteroidetes and Actinobacteria were the major groups on the anode, while γ-, β-, and α-Proteobacteria, Bacteroidetes and Actinobacteria were the predominant groups on the cathode.     

Convergent development of anodic bacterial communities in microbial fuel cells

Microbial fuel cells (MFCs) are often inoculated from a single wastewater source. The extent that the inoculum affects community development or power production is unknown. The stable anodic microbial communities in MFCs were examined using three inocula: a wastewater treatment plant sample known to produce consistent power densities, a second wastewater treatment plant sample, and an anaerobic bog sediment. The bog-inoculated MFCs initially produced higher power densities than the wastewater-inoculated MFCs, but after 20 cycles all MFCs on average converged to similar voltages (470±20 mV) and maximum power densities (590±170 mW m⁻²). The power output from replicate bog-inoculated MFCs was not significantly different, but one wastewater-inoculated MFC (UAJA3 (UAJA, University Area Joint Authority Wastewater Treatment Plant)) produced substantially less power. Denaturing gradient gel electrophoresis profiling showed a stable exoelectrogenic biofilm community in all samples after 11 cycles. After 16 cycles the predominance of Geobacter spp. in anode communities was identified using 16S rRNA gene clone libraries (58±10%), fluorescent in-situ hybridization (FISH) (63±6%) and pyrosequencing (81±4%). While the clone library analysis for the underperforming UAJA3 had a significantly lower percentage of Geobacter spp. sequences (36%), suggesting that a predominance of this microbe was needed for convergent power densities, the lower percentage of this species was not verified by FISH or pyrosequencing analyses. These results show that the predominance of Geobacter spp. in acetate-fed systems was consistent with good MFC performance and independent of the inoculum source.     

Power production in MFCs inoculated with Shewanella oneidensis MR‐1 or mixed cultures

Power densities and oxidation–reduction potentials (ORPs) of MFCs containing a pure culture of Shewanella oneidensis MR‐1 were compared to mixed cultures (wastewater inoculum) in cube shaped, 1‐, 2‐, and 3‐bottle batch‐fed MFC reactor configurations. The reactor architecture influenced the relative power produced by the different inocula, with the mixed culture generating 68–480% more power than MR‐1 in each MFC configuration. The mixed culture produced the maximum power density of 858 ± 9 mW m^?2 in the cubic MFC, while MR‐1 produced 148 ± 20 mW m^?2. The higher power by the mixed culture was primarily a result of lower internal resistances than those produced by the pure culture. Power was a direct function of ohmic resistance for the mixed culture, but not for strain MR‐1. ORP of the anode compartment varied with reactor configuration and inoculum, and it was always negative during maximum power production but it did not vary in proportion to power output. The ORP varied primarily at the end of the cycle when substrate was depleted, with a change from a reductive environment during maximum power production (approximately ?175 mV for mixed and approximately ?210 mV for MR‐1 in cubic MFCs), to an oxidative environment at the end of the batch cycle (～250 mV for mixed and ～300 mV for MR‐1). Mixed cultures produced more power than MR‐1 MFCs even though their redox potential was less negative. These results demonstrate that differences between power densities produced by pure and mixed cultures depend on the MFC architecture. Biotechnol. Bioeng. 2010; 105: 489–498. © 2009 Wiley Periodicals, Inc.     

Evaluation of hydrolysis and fermentation rates in microbial fuel cells

This study determined the influence of substrate degradation on power generation in microbial fuel cells (MFCs) and microbial community selection on the anode. Air cathode MFCs were fed synthetic medium containing different substrates (acetate, glucose and starch) using primary clarifier sewage as source of electroactive bacteria. The complexity of the substrate affected the MFC performance both for power generation and COD removal. Power output decreased with an increase in substrate complexity from 99 ± 2 mW m⁻² for acetate to 4 ± 2 mW m⁻² for starch. The organic matter removal and coulombic efficiency (CE) of MFCs with acetate and glucose (82% of COD removal and 26% CE) were greater than MFCs using starch (60% of COD removal and 19% of CE). The combined hydrolysis–fermentation rate obtained (0.0024 h⁻¹) was considerably lower than the fermentation rate (0.018 h⁻¹), indicating that hydrolysis of complex compounds limits current output over fermentation. Statistical analysis of microbial community fingerprints, developed on the anode, showed that microbial communities were enriched according to the type of substrate used. Microbial communities producing high power outputs (fed acetate) clustered separately from bacterial communities producing low power outputs (fed complex compounds).