Staining of Bacterial Colonies on the Millipore Filter to Improve Contrast

About 5 ml of 1% blue tetrazolium in 70% ethyl alcohol were poured over mature colonies of Pasteurella pestis and Malleomyces pseudomallei on Millipore filters (MF), contained in the filter holder apparatus, and allowed to drain through with the suction applied. The MF was washed with water and then covered with about 10 ml of 0.001% aqueous trypan blue and drained. This technique provided vivid white colonies sharply defined against a blue background.

Another method utilized 0.1% quinacrine-HCl (Atabrine) to stain colonies yellow and 0.05% vital red to stain the MF pink to light red.     

Differentiation of Articular and Epiphysial Cartilage, Based on Resorcin-CrystaeL Violet and Picro-Fuchsin Staining of Chondroitin Sulphate and Keratosulphate

Formalin-fixed, decalcified knee joints of young vertebrates were embedded in paraffin wax and cut at 4 μ. Sections were stained in Harris' Haematoxylin, washed in tap water, then immersed in the following staining solution for 60 min: crystal violet, 1 gm; resorcin, 2 gm; distilled water, 100 ml; boiled for 3 min, with constant stirring. After adding 30 ml of 30% FeCl₃, it was boiled for 3 min more. The solution was filtered. The precipitate was washed oil with 50 ml of distilled water and 100 ml of absolute alcohol added. This was combined with the original filtrate and boiled for 5 min. The solution was filtered once more, the precipitate discarded and 2 ml of cone. HC1 added. After cooling, the solution was ready for use. Sections were then washed briefly in tap water, stained in van Gieson's picro-fuchsin for 2 min, and differentiated as they were dehydrated and brought to Xylene. The sections were mounted in a synthetic resin (D.P.X.). Articular type cartilage stains red and growth cartilage blue.     

A Nuclear Stain for Escherichia Coli And Related Organisms

The dye base of new fuchsin was precipitated by adding potassium hydroxide to the dye solution. The precipitate was filtered out and washed with water. It was then suspended in water, brought into solution and adjusted to a pH of about 5.0 with nitric acid. The staining solution was prepared by adding 0.3 ml. of a 14% aqueous solution of pyrogallol and 0.1 ml. of a 1% aqueous solution of boric acid to 3.0 ml. of the dye solution. Smears of cells were made in water on a slide and allowed to dry before covering with the staining solution which was also permitted to air dry. The smear was then washed in water and mordanted for 5-20 seconds in a 0.1% aqueous solution of mercuric nitrate. After rinsing in water, the smear was air dried. When dry, the slide was placed on a 50° C. warm plate for a few seconds before covering with a very thin film of a 5% aqueous solution of nigrosin which had a pH of about 5.0.     

Microcount Method for Petrolatum-Based Topical Ointments Containing Waxes

A practical solvent system for the detection of microorganisms in topical ointments has been developed. The method involves dissolving 0.5 g of topical ointment in 50 ml of a solvent mixture (92 parts isopropyl myristate, 6 parts carbon disulfide, and 2 parts xylene) and filtering it through a 0.45-mum membrane filter. Residual solvent is then washed from the filter pad with 200 ml of sterile 0.5% Brain Heart Infusion broth containing 0.1% Tween 80. The filter pad is then removed and placed on a petri plate containing Trypticase Soy Agar medium. The petri plates thus prepared are then incubated at 37 C for 7 days, and the colonies produced are then counted. The toxicity of the solvent mixture was determined against Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, Salmonella newington, and spores of Bacillus subtilis and was found to be less toxic than the heat-sterilized isopropyl myristate and comparable to the filter-sterilized isopropyl myristate.     

Hydrolysis and Biodegradation of the Vesicant Agent HT: Two Potential Approaches

HT is a powerful vesicant produced for use as a chemical warfare agent. It is a mixture of 60 wt% 2,2' -dichlorodiethyl sulfide (“HD” or “sulfur mustard”) and 40 wt% bis-(2-(2-chloroethylthio)ethyl) ether (T). Because HT reacts with water to form primarily the alcoholic compounds thiodiglycol (TDG) and bis-(2-(2-hydroxyethylthio)ethyl) ether (T-OH), disposal might be accomplished by combining hydrolysis with biodegradation. The half-lives of H and T in a well-agitated 3.8% HT/water reaction at 90°C were 1.4 and 1.6 minutes, respectively. The concentrations of both compounds were reduced to less than 1 mg/L within about 30 minutes. TDG is readily biodegradable. However, T-OH biodegradability has not been reported previously. HBr treatment converted HT ether-alcohol products to TDG. A comparative study of two hydrolysis/biodegradation approaches is reported here. HT was hydrolyzed (1) in water, and (2) in water then with HBr. Products were used as feed for separate aerobic sequencing batch reactors (SBRs), and bioreactor performances were compared. Although both feed solutions were detoxified in the SBRs, water hydrolysis alone yielded better overall bioreactor operation, a more favorable mass balance, and a simpler process than with the HBr step. Results indicated that although the HBr converted ether-alcohol products to TDG, the HT products were biodegraded with greater efficiency when the HBr treatment was omitted.     

A Pollen Grain Squash Technique for Saccharum and Related Genera

Anthers collected between 9 and 10 AM were treated for 1 hr at 26-28 C with a 0.5% solution of colchicine, washed for 2-4 min in water, placed in 0.002 M 8-hydroxyquinoline for 1 hr, washed in water for 10 min and fixed in: methanol, 60 ml; chloroform, 30 ml; distilled water, 20 ml; picric acid, 1 gm and mercuric chloride 1 gm, for 24 hr. After washing they were hydrolysed in 1 N HCl for 15 min at 60 C, stained in leuco basic fuchsin for 30 min, then smeared on a slide in a drop of acetocarmine. The slides were sealed, stored overnight, the paraffin was removed, and the slide passed through a 1:1 mixture of n-butyl alcohol and acetic acid, then through pure n-butyl alcohol and mounted in Canada balsam. The significant features of this procedure are: (1) use of chromosomes in the haploid condition for karyotype analysis, (2) better exaggeration of constrictions for easier interpretation of chromosome types and (3) good spreading in plants with a large chromosome number.     

Handling Germinated Pollen on Millipore Membrane During the Feulgen and Autoradiographic Procedures

To prevent loss of pollen during the Feulgen's procedure, the pollen was grown on an autoclaved membrane filter (Millipore AA WP 025 00) in contact with a sterilized medium containing agar 0.5-1%, sucrose according to the genus (Malus 0.3-0.5 M; Persica and Tulipa 0.4 M), and H₃BO₃, 0.01%. To fix the germinated pollen of most species, the membrane was placed for 2 hr to overnight at 2-4 C on filter paper wet with the following mixture: OsO₄, 1 gm; CrO₃, 1.66 gm; and distilled water, 233 ml. To fix Persica pollen, 10% of glacial acetic acid had to be added to the fixative. Washing with distilled water and bleaching with a mixture of 3% H₂O₂ and sat. aq. ammonium oxalate, 1:1, were performed also on filter paper. Similarly, the preparation was processed for Feulgen staining by use of pieces of filter paper wet with the required fluids. Hydrolysis preceding the Schiff's reagent was performed at room temperature with 5 N HCl for 18 min. The differentiation after the Schiff's action was with 2% K₂S₂O₅ buffered to pH 2.3 with 9 ml of phosphate buffer (KH₂PO₄, 1.4 gm; conc. HCl, 0.35 ml and distilled water to make 100 ml). The stained pollen was floated off the membrane with a drop of glacial acetic acid to a gelatinized or an albumenized slide, and squashed. When the coverslip is removed the preparation may be either dehydrated and mounted or coated with autoradiographic film.     

Methyl Green-Pyronin for Staining Autoradiographs of Hydroxyethyl Methacrylate-Embedded Lymphoid Tissue

Cells in the spleen in DNA-synthesis were labelled with tritiated thymidine. Tissue was fixed for 12 hr in 10% neutral formalin, washed for 4 hr in tap water and dehydrated through 70% and absolute ethanol. The tissue blocks were infiltrated overnight with a mixture consisting of glycol methacrylate, 80 ml; polyethylene glycol 400, 12 ml; and benzoyl peroxide, 0.27 gm. Specimens were cast in BEEM capsules with the final embedding medium consisting of 42 parts of the infiltration medium and 1 part of an acceleration mixture. This mixture consisted of N,N-dimethylaniline, 1 part and polyethylene glycol 400, 15 parts. The blocks hardened in 30 min and were sectioned with an ultramicrotome fitted with glass knives. Sections were coated with Ilford K5 liquid emulsion and exposed for 2 wk. Methyl green-pyronin staining of autoradiographs was carried out at pH 4.1 in acetate buffer containing 0.5% methyl green (Allied Chemicals) and 0.2% pyronin GS (Chroma). Staining was for 30-60 min, after which sections were washed for 1 min in water, blotted, allowed to dry, and mounted in Canada balsm. The procedure resulted in good quality autoradiographs in which the degree of basophilia of labelled cells could be assessed.     

Chromosomes of Sequoia sempervirens; 8-Hydroxy-Quinoline-Castor Oil Pretreatment for Improving Preparation

Living root tips of coast redwood were pretreated for 6 hr at 10-14 C in a homogenized mixture of 0.003 M aqueous solution of about 5 ml of 8-hydroxyquinoline and a drop of castor oil. They were rinsed 2-3 times in Carnoy's alcohol-chloroform-acetic acid (3:2:1), and fixation allowed to continue in this fluid for 1 hr at 60 C. They were then hydrolysed in 1 N HC1 at 60 C for 45 min; washed with distilled water, and squashed in a drop of aceto-carmine or aceto-orcein to make a temporary slide, subsequently made permanent by a quick-freezing method. Our work to date seems to confirm 2n = 66 for S. sempervirens.     

Carbowax for Embedding and Serial Sectioning of Botanical Material

Plant material infiltrated with gradually increasing concentrations of Carbowax 400, followed by Carbowax 1540 and finally a 19:1 embedding mixture of Carbowax 1540 and 4000 showed minimum shrinkage. Quantitative measurements of shrinkage in tissue of potato tubers gave the following amounts: fixation and washing, about 4%; transfer from water directly to 70% Carbowax 400, 5176; from water through a graded series (5, 10, 15, 20, 30, 40, 50 and 60% Carbowax) to 70%, only 2.5% shrinkage; with an additional 1.5% occurring in transition to the embedding mixture. Dry ribbons are placed on adhesive-coated (gelatin, 5 gm; water, 120 ml; glycerol, 40 ml; phenol, 2 gm) slides in a humidity chamber. In 10-15 min enough moisture is absorbed by the ribbon to float the sections out gently and bring them in contact with the adhesive. Slides are then dried 5-10 min at room temperature. To remove minor wrinkles, the sections are subsequently flooded with water, then redried 12-24 hr; after which, they are ready for staining.     

Hydroxyethyl Methacrylate Combined with Polyethylene Glycol 400 and Water; an Embedding Medium for Routine 1-2 Micron Sectioning

Pieces of tissue, with the largest dimension not exceeding 7 mm, are fixed and dehydrated by the procedures of choice. Two stock solutions: A, for infiltration; and B, the accelerator, are used in embedding. Formulas: A, 80 ml of glycol methacrylate (2-hydroxyethyl methacrylate—Rohm and Haas Co., Philadelphia, Pa.) is mixed well with 12 ml of polyethylene glycol (Carbowax) 400 and 8 ml of water; then 0.27 gm of benzoyl peroxide added, heated to dissolve the peroxide, and allowed to cool to room temperature. B, polyethylene 200 or 400, 15 parts, and N,N-dimethylaniline, 1 part, mixed thoroughly. Tissues are first infiltrated completely with solution A, then cast in a mixture consisting of 42 parts of A mixed with 1 part of B. Polymerization occurs in 45 min to 3 hr, depending on the temperature. In a water bath at 20 C, the time required was found to be about 3 hr; at 25 C, 1.5 hr; and at 30 C, 45 min. The plastic block can be trimmed easily, and sections 1-2 μ thick readily cut. Sections can be attached to slides by water flotation, without adhesive, and should be dried at room temperature. Staining with aqueous solutions of basic and acid dyes, without removing the embedding matrix, is sharp and brilliant. When staining of the matrix by basic dyes occurs, this background stain can be completely removed by differentiating in either 2-butoxyethanol, pure ethanol, or a mixture of the two. A number of histochemical reagents have been found compatible with this embedding procedure.     

Isolation and identification of androstanediol glucuronide from human plasma

[3H]Dihydrotestosterone (50 microCi) was infused into normal men and women for 8 h. It was previously shown that this was sufficient time for this material to reach a steady state. Venous plasma was obtained at 6 and 8 h, pooled, and the unconjugated steroids removed by ether extraction. The remaining plasma was adjusted to pH 4.9 and the steroid conjugate was extracted first with ethyl acetate and then with an ether-ethanol mixture. The extracts were combined and taken to dryness. Steroid sulfates were solvolyzed using dioxane, and the mixture partitioned between ether and 1% NaOH. The aqueous phase was acidified and added to an XAD-2 column, washed with water, and the glucuronide fraction eluted with methanol. The solvent was concentrated and the methanol extract was passed through a C18 Sep-Pak, filtered through an Acrodisc CR and then subjected to gradient high performance liquid chromatography [HPLC] (Nova-Pak C18, KH2PO4, pH 3, and methanol). The fractions containing steroid glucuronides were collected and esterified with diazomethane and then acetylated with acetic anhydride in pyridine. The glucuronide triacetyl methyl ester (GAME) derivatives were then run in a second HPLC system (3 Lichrosorb 5 mu columns, 4 mm x 25 cm) using a gradient of ethanol-heptane and heptane. We clearly established that this system separates 3 alpha-diol GAME conjugated at the 17 and 3 positions (44 vs 50 min) with authentic samples previously synthesized in our laboratory. We concluded that the pooled plasma contained only the 17-GAME conjugate. No significant activity of the 3-glucuronide was detected. The natural compound in circulation, therefore, is 5 alpha-androstane-3 alpha, 17 beta-diol 17-glucuronide.     

A Modified Pyridine-Silver Stain for Teased Preparations of Motor and Sensory Nerve Endings in Skeletal Muscle

This technique has been developed especially to stain sensory receptors which have been localised intramuscularly by electrophysiological means. Rat intertransverse caudal muscles, removed immediately after death, are fixed for 24 hr in a freshly prepared mixture of absolute ethyl alcohol, 4.5 ml; distilled water, 5 ml; and concentrated HNO_a, 0.1 ml. After a further 24 hr in 10 ml of absolute ethyl alcohol containing 0.1 ml of ammonia solution (sp. gr. 0.88), the muscles are washed in distilled water for 30 min and placed in full strength pyridine for 2 days. They are then washed for 24 hr in distilled water (changed 5-8 times) and left in 2% AgNO₃, in the dark for 3 days at 25 C. Following reduction in 10 ml of 5% formic acid containing 0.4 gm of pyrogallol for 6-24 hr, the specimens are washed briefly in distilled water and stored in pure glycerol. The nerve endings can then be teased out and mounted in glycerol, under cover glasses ringed with a waterproof cement. The advantage of this method is that it gives consistently good staining of receptors and motor end-plates in small muscles of the rat     

Preservation of fine structure in vibratome-cut sections of the central nervous system stained for light microscopy

A technique without negative effects on tissue preservation that allows precise identification and subsequent removal of central nervous system nuclei for ultrastructural analysis is described. The procedure uses 200 microns thick Vibratome-cut sections of glutaraldehyde fixed brains. These sections are stained for 25 seconds with a methylene blue solution and stored for 4 hours in 0.2 M pH 7.4 phosphate buffer in 4% sucrose for optimal visualization at the light microscopic level. The stock solution of 1 g methylene blue and 1 g sodium borate in 100 ml of distilled water, is filtered through a Millipore filter and diluted 5:95 with distilled water immediately prior to use. Regions of specific interest are then processed for electron microscopy.     

Stereoselective determination of R-(+)- and S-(−)-remoxipride, a dopamine D2-receptor antagonist, in human plasma by chiral high-performance liquid chromatography

A stereoselective high-performance liquid chromatographic (HPLC) method is described for the selective and sensitive quantitation in human plasma of R-(+)- and S-(−)-enantiomers of remoxipride. Remoxipride was extracted from basified plasma into hexane-methyl-tert.-butyl ether (20:80, v/v), washed with sodium hydroxide (1.0 M), then back-extracted into phosphoric acid (0.1 M). A structural analog of remoxipride was used as an internal standard. The sample extracts were chromatographed using a silica-based derivatized cellulose chiral column, Chiralcel OD-R, and a reversed-phase eluent containing 30–32% acetonitrile in 0.1 M potassium hexafluorophosphate. Ultraviolet (UV) absorbance detection was performed at 214 nm. Using 0.5-ml plasma aliquots, the method was validated in the concentration range 0.02-2.0 μg/ml and was applied in the investigation of systemic inversion of remoxipride enantiomers in man.     

An Improved Pollen Grain Smear Method for Wheat

Anthers containing actively dividing pollen grains were treated 1 hour at 18-20° C. with 0.2% solution of colchicine, washed 1 hour in water, soaked in 0.002 M aqueous solution of 8-oxyquinoline at 10-14° C. for 1 hour, washed in water for 1 hour and then fixed in Carnoy's solution (alcohol, chloroform, acetic acid, 6:3:1) for 6 hours to overnight. They were washed successively in acetic-alcohol (1:1) 10-15 minutes, 70% alcohol 10-15 minutes and in water 30 minutes before hydrolysing them in bulk in 1 N HCl at 60° C. for 10-15 minutes. “Finally, they were stained in leuco-basic fuchsin for 15-30 minutes. Pollen grains were squeezed out of a stained anther in a small drop of egg albumen on a slide and the albumen smeared uniformly on the slide. The slide was dipped successively for a few seconds in glacial acetic acid and 45% acetic acid respectively. The smear was covered by a cover glass in a drop of aceto-carmine and pressed gently between folded filter papers. The cover glass was sealed with paraffin and stored overnight. To make the preparation permanent the paraffin was removed and the cover glass separated in a 1:1 mixture of acetic acid and n-butyl alcohol. The slide and the cover glass were then passed through n-butyl alcohol, 2 changes, and finally remounted in balsam.     

Staining the Nucleus in Yeasts

Yeast cells kept young by repeated subculturing were centrifuged, washed twice in distilled water and smeared on slides coated with a little egg albumen. The cells were treated with 0.002 M 8-hydroxyquinoline for 1 hr, fixed first in OsO, vapour for 30 sec and then in chloroform for 30 sec. The slides were passed through descending grades of alcohol, washed in distilled water, then immersed in 0.17 M NaCl solution for 2 hr. at 57°C. They were again washed in distilled water and later hydrolysed in 1 N HCl at 60°C for 5-7 min. This was followed by washing in distilled water and in buffer. The slides were then kept for 3 hr in Giemsa stain comprising 96 ml of phosphate buffer of pH 7.0 and 4 ml of the stain. After dehydration, mounting was done in balsam. Nuclei were brightly stained and well differentiated; centrosomes were clear, and the process of nuclear division and movement to daughter cells could be studied. Pretreatment with 8-hydroxyquinoline increased the viscosity of the cytoplasm, while NaCl treatment and acid hydrolysis led to the complete removal of ribonucleic acid and basophilic material. A selective staining of chromatin was thus achieved. Structures resembling chromosomes could be seen when fixed and stained cells were squashed, soon after the removal of the slides from the stain, under a cover glass by applying uniform pressure with a rubber stopper. Fixation in osmic acid vapor and chloroform followed by acid hydrolysis and staining in leucobasic fuchsin also helps to obtain bright staining of the nucleus; however, the preparations are inferior to those obtained after 8-hydroxyquinoline, NaCl treatment and Giemsa staining.     

Sugar ester synthesis by a mycelium-bound Mucor circinelloides lipase in a micro-reactor equipped with water activity sensor

The mycelium-bound Mucor circinelloides lipase was used for the synthesis of esters of saccharides and fatty acids in 37 ml reactor equipped with magnetic stirrer and water activity sensor. Either di-n-pentyl ether or the mixture of di-n-pentyl and petroleum ethers were applied as reaction media. Water activity sensor provided on-line monitoring of this parameter and control of continuous processes of ester synthesis. It was found that two natural antioxidants, i.e. carotene and astaxanthin activated this lipase in organic solvents that could be beneficial for the synthesis of esters of compounds sensitive to oxidation, e.g. polyunsaturated fatty acids.     

A Rapid Technique for Preparing Microorganisms for Transmission Electron Microscopy

A rapid and efficient method of preparing microorganisms for transmission electors microscopy is reported. In developing the method Salmonella, streptococcal, ad protozoal specimens were fixed with glutaraldehyde. After fixation cells are collected on a membrane filter, washed with buffer, postfixed with osmium tetroxide, then washed with distilled water and stained en bloc with uranyl acetate. Specimens are dehydrated using a graded series of acetone and then infiltrated with graded mixtures of acetone and Spurr embedding medium. Finally the membrane filter is cut into small pieces and embedded in fresh embedding medium polymerized in polyethylene capsules. By collecting and processing the specimens on membrane filters, numerous centrifugations are eliminated from standard procedures. The use of a low viscosity embedding medium allows for rapid infiltration and embedding of the specimen. Using this technique microbial specimens can be sectioned after less than 4 hours preparation.     

Differential Staining Of Tissue In The Block With Picric Acid And The Feulgen Reaction

The authors have found a modification of the Feulgen reaction to be a satisfactory stain for tissue in the block.

Pieces of fresh mammalian tissue not thicker than 5 mm. are fixed for approximately 48 hours at 25° C. in a mixture of equal parts of 5% aqueous sulfosalicylic acid and saturated aqueous picric acid. They are washed for 30 minutes in three ten-minute changes of distilled water and placed in Feulgen's staining solution diluted to one-half strength with distilled water. The staining solution is allowed to act for 24 hours (2 to 3 mm. thick blocks) up to 48 hours for 5 mm. thickness. After staining, the specimens are transferred to a mixture of sodium bisulfite, 0.5 g. and N hydrochloric acid, 5 ml. in' 100 ml. of distilled water. Two changes of IS to 30 min. each in the acid sulfite are given and these are followed by dehydration through 50%, 70% and 95% alcohol. One to two hours are allowed for each change except the last 95%, in which the stained tissue is allowed to remain overnight. The dehydration is completed in two changes of absolute alcohol with subsequent clearing in xylene and embedding in paraffin. Sections may be cut 10 μ or other thickness desired, mounted on slides, paraffin removed, and covered in the usual manner. Nuclei stain reddish violet against a lemon yellow background when the stain is typical. Orange G, 200 mg. per 100 ml. may be added to the fixing fluid if a more polychromatic effect is desired.