β-Carotene extraction from Dunaliella salina by supercritical CO2

This paper reports the results of supercritical carbon dioxide (scCO₂) extraction of β-carotene from Dunaliella salina as potential alternative to conventional organic solvent extraction. In pilot-scale scCO₂ experiments, the pressure, temperature, and co-solvent concentration were varied. The supercritical extraction at 500 bar, 70 °C, and 10 wt% ethanol as co-solvent yielded in the highly efficient pigment recovery of over 90%. Techno-economic assessment demonstrated higher energy consumption for the scCO₂ extraction that was compensated by lower solvent costs. Thus, comparable pigment production costs to the reference extraction with n-hexane were estimated for the scCO₂ process. Due to the green solvent properties of scCO₂ and ethanol, this approach is highly promising for extraction of algal biomass in industrial scale.

     

Supercritical Extraction of Carotenoids from Rosa canina L. Hips and their Formulation with β-Cyclodextrin

The purpose of this research was to preliminary assess the suitability of a new method for the preparation of a solid formulation in form of powder composed by β-cyclodextrin and the supercritical extract of Rosa canina hips. The method implies the extraction of carotenoids, in particular β-carotene, from freeze dried fruits of R. canina with supercritical CO₂ at 70 °C and 300 bar, in the presence of varying quantity of ethanol as entrainer. The obtained supercritical solution is then expanded at ambient conditions into an aqueous solution of β-cyclodextrin to favour the interaction between β-cyclodextrin and the lipophilic components of the extract. β-carotene solubility (mole fraction) in supercritical CO₂ or in supercritical CO₂/ethanol mixtures were in the order of 1 10⁻⁷. The β-carotene extracted from R. canina fruits (nearly 10 μg/g of dry matrix), interacts almost quantitatively with β-cyclodextrin affording a solid phase, which presents a low apparent solubility in water. Finally the interaction with β-cyclodextrin results in a higher concentration of the β-carotene trans- form relative to the cis- form in the extracted product when collected in an aqueous solution of β-cyclodextrin with respect to the extract in n-hexane.     

Durum wheat by-products as natural sources of valuable nutrients

This review reports the use of wheat milling by-products for the extraction of high quality oil and vitamin E including our results on the exploitation of durum wheat bran as a valuable source of important healthful compounds. Wheat oil can be used as an ingredient in food, pharmaceutical or cosmetic preparations because it contains important bioactive compounds such as vitamin E, carotenoids and unsaturated fatty acids. Different methods are used for oil recovery from plant materials, such as solvent extraction, mechanical pressing or the eco-friendly supercritical carbon dioxide (SC-CO₂) extraction technology. By using SC-CO₂, we obtained an oil from durum wheat (Triticum durum Desf.) bran and optimized the extraction conditions to increase oil and vitamin E yields. Wheat bran, which is composed of pericarp, aleurone layer and germ, is discarded during the early stages of durum wheat milling processes to obtain a final product (semolina) that is stable over time. Maximum oil and vitamin E yields were obtained when a durum wheat bran matrix with particle size of ~30 mesh and a moisture content of 2.6 % was used. The optimal conditions for oil extraction were: 300–350 bar, 60–70 °C, and 4 l min^?1 gaseous CO₂ flow rate for 1 h. The chemical composition (vitamin E forms, carotenoids, quinones, lipids and fatty acids) of the SC-CO₂ extracted oil was analyzed and compared to that of the oil extracted by Soxhlet using hexane as solvent. The findings here reported highlight the importance of durum wheat bran as a rich source of valuable natural nutrients.     

Chemical composition and antibacterial activity of Cordia verbenacea extracts obtained by different methods

The present study describes the chemical composition and the antibacterial activity of extracts from Cordia verbenacea DC (Borraginaceae), a traditional medicinal plant that grows widely along the southeastern coast of Brazil. The extracts were obtained using different extraction techniques: high-pressure operations and low-pressure methods. The high-pressure technique was applied to obtain C. verbenacea extracts using pure CO₂ and CO₂ with co-solvent at pressures up to 30 MPa and temperatures of 30, 40 and 50 °C. Organic solvents such as n-hexane, ethyl acetate, ethanol, acetone and dichloromethane were used to obtain extracts by low-pressure processes. The antibacterial activity of the extracts was also subjected to screening against four strains of bacteria using the agar dilution method. The extraction yields were up to 5.0% w/w and up to 8.6% w/w for supercritical fluid extraction with pure CO₂ and with ethyl acetate as co-solvent, respectively, while the low-pressure extraction indicates yields up to 24.0% w/w in the soxhlet extraction using water and aqueous mixture with 50% ethanol as solvents. The inhibitory activity of the extracts in Gram-positive bacteria was significantly higher than in Gram-negative. The quantification and the identification of the extracts recovered were accomplished using GC/MS analysis. The most important components identified in the extract were artemetin, β-sitosterol, α-humulene and β-caryophyllene, among others.     

Extraction of fucoxanthin and polyphenol from <Emphasis Type="Italic">Undaria pinnatifida</Emphasis> using supercritical carbon dioxide with co-solvent

Extraction of brown seaweed (Undaria pinnatifida) oil was carried out by using supercritical carbon dioxide (SCO₂) and ethanol as co-solvent. The flow rate of ethanol was 3.0% (v/v) as compared to that of SCO₂. Experiments were performed in a semi-batch flow apparatus on dried samples at temperatures from 303 to 333 K and pressures from 80 to 300 bar. Fucoxanthin and polyphenol were quantitatively analyzed by using HPLC and UV-spectrometer. The highest yields of fucoxanthin and polyphenol were shown at 200 bar, 323 K and 250 bar, 333 K, respectively. The solubility of fucoxanthin in SCO₂ agreed well with the Chrastil model.     

Optimization of enzymatic hydrolysis of triglycerides in soy deodorized distillate with supercritical carbon dioxide

Enzymatic hydrolysis of triglycerides of soy deodorized distillate (DOD), using immobilized Candida rugosa lipase under supercritical carbon dioxide (SC-CO₂) medium, was carried out. Optimization of the reaction parameters using response surface methodology based on Box-Behnken model at three levels of pressure (120–180 bar), temperature (40–60 °C) and moisture content (40–80% of triglyceride content) for maximum hydrolysis of triglycerides was arrived by multilinear regression of the experimental results. The optimum conditions for maximum degree of triglyceride hydrolysis (94%) were found to be: pressure of 180 bar, temperature of 43 °C and moisture content of 40% to the triglyceride content. Maximum degree of hydrolysis was achieved with short incubation time of 1.5 h under SC-CO₂. Whereas conventional method of hydrolysis in hexane under similar reaction conditions of temperature, moisture and enzyme concentration, needs 5 h to achieve 88% of triglyceride hydrolysis.     

Optimization of supercritical carbon dioxide extraction of silkworm pupal oil applying the response surface methodology

Supercritical carbon dioxide extraction (SC-CO₂) of oil from desilked silkworm pupae was performed. Response surface methodology (RSM) was applied to optimize the parameters of SC-CO₂ extraction. The effects of independent variables, including pressure, temperature, CO₂ flow rate, and extraction time, on the yield of oil were investigated. The statistical analysis showed that the pressure, extraction time, and the quadratics of pressure, extraction time, and CO₂ flow rate, as well as the interactions between pressure and temperature, and temperature and flow rate, showed significant effects on oil yield. The optimal extraction condition for oil yield within the experimental range of the variables researched was at 324.5 bar, 39.6 °C, 131.2 min, and 19.3 L/h. At this condition, the yield of oil was predicted to be 29.73%. The obtained silkworm pupal oil contained more than 68% total unsaturated fatty acids, and alpha-linolenic acid (ALA) accounted for 27.99% in the total oil.     

Extraction of microalgae derived lipids with supercritical carbon dioxide in an industrial relevant pilot plant

Microalgae are capable of producing up to 70% w/w triglycerides with respect to their dry cell weight. Since microalgae utilize the greenhouse gas CO₂, they can be cultivated on marginal lands and grow up to ten times faster than terrestrial plants, the generation of algae oils is a promising option for the development of sustainable bioprocesses, that are of interest for the chemical lubricant, cosmetic and food industry. For the first time we have carried out the optimization of supercritical carbon dioxide (SCCO₂) mediated lipid extraction from biomass of the microalgae Scenedesmus obliquus and Scenedesmus obtusiusculus under industrrially relevant conditions. All experiments were carried out in an industrial pilot plant setting, according to current ATEX directives, with batch sizes up to 1.3 kg. Different combinations of pressure (7–80 MPa), temperature (20–200 °C) and CO₂ to biomass ratio (20–200) have been tested on the dried biomass. The most efficient conditions were found to be 12 MPa pressure, a temperature of 20 °C and a CO₂ to biomass ratio of 100, resulting in a high extraction efficiency of up to 92%. Since the optimized CO₂ extraction still yields a crude triglyceride product that contains various algae derived contaminants, such as chlorophyll and carotenoids, a very effective and scalable purification procedure, based on cost efficient bentonite based adsorbers, was devised. In addition to the sequential extraction and purification procedure, we present a consolidated online-bleaching procedure for algae derived oils that is realized within the supercritical CO₂ extraction plant.

     

Enzymatic activity of L-amino acid oxidase from snake venom Crotalus adamanteus in supercritical CO2

L-amino acid oxidase (L-AAO) from snake venom Crotalus adamanteus was successfully tested as a catalyst in supercritical CO₂ (SC-CO₂). The enzyme activity was measured before and after exposure to supercritical conditions (40°C, 110 bar). It was found that L-AAO activity slightly increased after SC-CO₂ exposure by up to 15%. L-AAO was more stable in supercritical CO₂ than in phosphate buffer under atmospheric pressure, as well as in the enzyme membrane reactor (EMR) experiment. 3,4-Dihydroxyphenyl-L-alanine (L-DOPA) oxidation was performed in a batch reactor made of stainless steel that could withstand the pressures of SC-CO₂, in which L-amino acid oxidase from C. adamanteus was able to catalyze the reaction of oxidative deamination of L-DOPA in SC-CO₂. For the comparison L-DOPA oxidation was performed in the EMR at 40°C and pressure of 2.5 bar. Productivity expressed as mmol-s of converted L-DOPA after 3?h per change of enzyme activity after 3?h was the highest in SC-CO₂ (1.474?mmol?U^?1), where catalase was present, and the lowest in the EMR (0.457?mmol?U^?1).     

<Emphasis Type="Italic">Neochloris oleabundans</Emphasis> UTEX #1185: a suitable renewable lipid source for biofuel production

Energy crises, global warming, and climatic changes call for technological and commercial advances in manufacturing high-quality transportation fuels from unconventional feedstocks. Microalgae is one of the most promising sources of biofuels due to the high yields attained per unit area and because it does not displace food crops. Neochloris oleabundans (Neo) microalga is an important promising microbial source of single-cell oil (SCO). Different experimental growth and lipid production conditions were evaluated and compared by using optical density (540 nm), dry-weight determination, and flow cytometry (FC). Best Neo average biomass productivity was obtained at 30°C under conditions of nitrogen-sufficiency and CO₂ supplementation (N+/30°C/CO₂), with an average doubling time of 1.4 days. The second and third highest productivities occurred with N-sufficient cultures without CO₂ supplementation at 26°C (N+/26°C) and at 30°C (N+/30°C), with doubling times of 1.7 and 2.2 days, respectively. Microbial lipid production was monitored by flow cytometry using Nile red (NR), a lipophilic fluorochrome that possesses several advantageous characteristics for in situ screening near real time (at line). Results showed maximum lipid content (56%) after 6 days of nitrogen depletion under nitrogen starvation without CO₂ supplementation (N−/30°C), followed by N−/30°C/CO₂ and N−/26°C conditions with 52% lipid content, after 5 and 6 days of N starvation, respectively. The adequate fatty acid profile and iodine value of Neo lipids reinforced this microalga as a good source of SCO, in particular for use as biodiesel.     

Antileishmanial activity of fucosterol recovered from Lessonia vadosa Searles (Lessoniaceae) by SFE,PSE and CPC

Fucosterol, a triterpene derivative encountered in several alga species, provides a wide range of biological activities, such as protection against metabolic syndrome, or against UV-induced skin damage. We describe here the comparison of extraction by supercritical fluid (SFE) and pressurized solvent (PSE) of the brown alga Lessonia vadosa mainly abundant in the coastal water of Patagonia, followed by the isolation of fucosterol, using centrifugal partition chromatography (CPC), in association with HPLC–UV quantification. After collection, the seaweed was dried, ground and extracted either by PSE or by SFE under various conditions. The yield and the content in fucosterol of each extract were determined by HPLC–UV. Optimization of a biphasic solvent system and K_D calculation led to the isolation of pure fucosterol with high recovery rate. Extraction by SFE using CO₂ at 180 bar and 50 °C with 20 to 30 % of cellulose as modifier and CPC purification by cyclohexane/acetone/methanol/water 10/1/10/1 with lower layer as mobile phase led to the best results in terms of yield, purity, time and solvent consumption. Natural and semisynthetic steroid derivatives have been previously shown to be potential drug candidates against parasitic diseases including leishmaniasis. In this context fucosterol was evaluated and demonstrated noticeable antileishmanial activity (IC₅₀ < 10 μM) against intracellular amastigotes with limited or no cytotoxicity in host cell macrophages. These results make this compound a valuable starting scaffold for pharmacomodulation. Adaptation of the procedure by slight modifications of the extraction and/or isolation conditions could permit the exploitation of other alga species as raw material. Since SFE and CPC are available for pilot and batch production, this work may serve as a model for further scale-up and industrial development.     

High-pressure CO2 inactivation and induced damage on Saccharomyces cerevisiae evaluated by flow cytometry

The cultivability, integrity and permeabilisation of Saccharomyces cerevisiae in saline solution after high-pressure CO₂ treatment at 36 °C was assessed by using both conventional cultivation-based technique and flow cytometry. Conventional cultivation-based techniques do not allow the exact quantification of integer cells, which can be determined coupling the staining with propidium iodide and SYBR-Green I and the cell quantification by flow cytometry. A significant portion of cells injured by CO₂ treatment is incapable of forming colonies but is still integer and potentially metabolically active. The yeast cell damage was demonstrated to be dependent on the conditions applied. In particular the influence of different operative parameters on integrity and permeabilisation of yeast cells was evaluated: pressure (50–100 bar), treating time (10–20 min) and stirring rate (500–10,000 rpm). After a 20 min treatment at 100 bar, 36 °C and 10,000 rpm more than 95% of cells result with completely permeabilised membrane.     

Generalized Mechanochemical Synthesis of Biomass‐Derived Sustainable Carbons for High Performance CO2 Storage

Novel mechanochemical activation generates biomass‐derived carbons with unprecedented CO₂ storage capacity due to higher porosity than analogous conventionally activated carbons but similar pore size. The mechanochemical activation, or so‐called compactivation, process involves compression, at 740 MPa, of mixtures of activating agent (KOH) and biomass hydrochar into pellets/disks prior to thermal activation. Despite the increase in surface area and pore volume of between 25% and 75% compared to conventionally activated carbons, virtually all of the porosity of the biomass (sawdust and lignin) derived mechanochemically activated carbons is from small micropores (5.8–6.5 Å), which results in a dramatic increase in CO₂ storage capacity at 25 °C and low pressure (≤1 bar). The ambient temperature CO₂ uptake for a carbon derived from sawdust at 600 °C and a KOH/carbon ratio of 2, rises from 1.3 to 2.0 mmol g^?1 at 0.15 bar, and from 4.3 to 5.8 mmol g^?1 at 1 bar, which is the highest ever reported for carbonaceous materials. The mechanochemically activated carbons have a superior CO₂ working capacity for pressure swing adsorption and vacuum swing adsorption processes and, due to a high packing density, they exhibit excellent volumetric CO₂ uptake that is higher than for any material reported to date.     

Response of the floating aquatic fern <Emphasis Type="Italic">Azolla filiculoides</Emphasis> to elevated CO<Subscript>2</Subscript>, temperature,and phosphorus levels

Azolla filiculoides is a floating aquatic fern growing in tropical and temperate freshwater ecosystems. As A. filiculoides has symbiotic nitrogen-fixing cyanobacteria (Anabaena azollae) within its leaf cavities, it is cultivated in rice paddies to improve N availability and suppress other wetland weeds. To understand how C assimilation and N accumulation in A. filiculoides respond to elevated atmospheric carbon dioxide concentration (CO₂) in combination with P addition and higher temperatures, we conducted pot experiments during the summer of 2007 and 2008. In 2007, we grew A. filiculoides in pots at two treatment levels of added P fertilizer and at two levels of [CO₂] (380 ppm for ambient and 680 ppm for elevated [CO₂]) in controlled-environment chambers. In 2008, we grew A. filiculoides in four controlled-environment chambers at two [CO₂] levels and two temperature levels (34/26°C (day/night) and 29/21°C). We found that biomass and C assimilation by A. filiculoides were significantly increased by elevated [CO₂], temperature, and P level (all P < 0.01), with a significant interaction between elevated [CO₂] and added P (P < 0.01). Tissue N content was decreased by elevated [CO₂] and increased by higher temperature and P level (all P < 0.01). The acetylene reduction assay showed that the N-fixation activity of A. filiculoides was not significantly different under ambient and elevated [CO₂] but was significantly stimulated by P addition. N-fixation activity decreased at higher temperatures (34/26°C), indicating that 29/21°C was more suitable for A. azollae growth. Therefore, we conclude that the N accumulation potential of A. filiculoides under future climate warming depends primarily on the temperature change and P availability, and C assimilation should be increased by elevated [CO₂].     

Novel regenerable potassium-based dry sorbents for CO2 capture at low temperatures

A novel potassium-based dry sorbent (KZrI) was developed for CO₂ capture at a low temperature range between 50 °C and 200 °C. The CO₂ absorption and regeneration properties of this novel regenerable potassium-based dry sorbent were measured in a fixed-bed reactor during multiple absorption/regeneration cycles at low temperature conditions (CO₂ absorption at 50–100 °C and regeneration at 130–200 °C). The total CO₂ capture capacity of the KZrI sorbent was maintained during the multiple CO₂ absorption/regeneration cycles. The XRD patterns and FTIR analyses of the sorbents after CO₂ absorption showed the KHCO₃ phase only except for the ZrO₂ phase used as support. Even after 10 cycles, any other new structures resulting from the by-product during CO₂ absorption were not observed. This phase could be easily converted into the original phase during regeneration, even at a low temperature (130 °C). The KZrI sorbent developed in this study showed excellent characteristics in CO₂ absorption and regeneration in that it satisfies the requirements of a large amount of CO₂ absorption (91.6 mg CO₂/g sorbent) and the complete regeneration at a low temperature condition (1 atm, 150 °C) without deactivation.     

Rise in CO<Subscript>2</Subscript> affects soil water transport through repellency

Several studies have shown improved soil stability under elevated atmospheric CO₂ caused by increased plant and microbial biomass. These studies have not quantified the mechanisms responsible for soil stabilisation or the effect on water relations. The objective of this study was to assess changes in water repellency under elevated CO₂. We hypothesised that increased plant biomass will drive an increase in water repellency, either directly or through secondary microbial processes. Barley plants were grown at ambient (360 ppm) and elevated (720 ppm) CO₂ concentrations in controlled chambers. Each plant was grown in a separate tube of 1.2 m length constructed from 22 mm depth × 47 mm width plastic conduit trunk and packed with sieved arable soil to 55% porosity. After 10 weeks growth the soil was dried at 40°C before measuring water sorptivity, ethanol sorptivity and repellency at many depths with a 0.14 mm radius microinfiltrometer. This provided a microscale measure of the capacity of soil to rewet after severe drying. At testing roots extended throughout the depth of the soil in the tube. The depth of the measurement had no effect on sorptivity or repellency. A rise in CO₂ resulted in a decrease in water sorptivity from 1.13 ± 0.06 (s.e) mm s^−1/2 to 1.00 ± 0.05 mm s^−1/2 (P < 0.05) and an increase in water repellency from 1.80 ± 0.09 to 2.07 ± 0.08 (P < 0.05). Ethanol sorptivity was not affected by CO₂ concentration, suggesting a similar pore structure. Repellency was therefore the primary cause of decreased water sorptivity. The implications will be both positive and negative, with repellency potentially increasing soil stability but also causing patchier wetting of the root-zone.     

Omega-3 fatty acids concentrate production by enzyme-catalyzed ethanolysis of supercritical CO<Subscript>2</Subscript> extracted oyster oil

The separation of oil by a suitable technique from the Pacific oyster muscle is important for the utilization of the oil as a ω-3 polyunsaturated fatty acids (ω-3 PUFAs) source and production of bio-functional peptides/ oligosaccharides from oil-free residue. This study was conducted to prepare ω-3 PUFAs concentrate from supercritical carbon dioxide (SC-CO₂) extracted Pacific oyster oil by enzyme-catalyzed ethanolysis reactions. SC-CO₂ extractions were done at different temperatures and pressures to optimize suitable extraction conditions and extracted oils were compared with Soxhlet (n-hexane) extracted oil to evaluate the yield and quality. Oil extracted by SC-CO₂ at optimized conditions was used for ethanolysis reaction catalyzed by immobilized sn-1,3 specific lipases, namely Novozymes-435, Lipozyme TLIM, and Lipozyme RMIM to produce 2-monoacylglycerols (2-MAG) rich in ω-3 PUFAs. The optimum temperature and pressure for SC-CO₂ extractions of oyster oil was 50°C and 30 MPa. In this condition, the yield of oil was 5.96% and the acid, peroxide, free fatty acid, and p-anisidine values were 4.49 mg KOH/g, 4.72 meq/kg, 3.42%, and 10.03, respectively. The ω-3 PUFAs content significantly increased in 2-MAG obtained from Novozymes 435, Lipozyme TLIM, and Lipozyme RMIM to 43.03 ± 0.36, 45.95 ± 0.29, and 40.50 ± 0.77%, respectively (p < 0.05). A thin layer chromatography (TLC) analysis confirmed the production and separation of 2-MAG in the ethanolysis process. The ratio of total ω-3 to ω-6 fatty acids was almost twice in 2-MAG of SC-CO₂ extracted oyster oil. SC-CO₂ extracted Pacific oyster oil can be used for sn-1,3 specific lipases catalyzed ethanolysis to produce ω-3 PUFAs rich in 2-MAG.     

Supercritical Carbon Dioxide Extraction of Allium ursinum: Impact of Temperature and Pressure on the Extracts Chemical Profile

The aim of this study was to extract Allium ursinum L. for the first time by supercritical carbon dioxide (SC−CO₂) as green sustainable method. The impact of temperature in the range from 40 to 60 °C and pressure between 150 and 400 bar on the quality of the obtained extracts and efficiency of the extraction was investigated. The highest extraction yield (3.43 %) was achieved by applying the extraction conditions of 400 bar and 60 °C. The analysis of the extracts was performed by gas chromatography and mass spectrometry (GC/MS). The most dominant sulfur-containing constituent of the extracts was allyl methyl trisulfide with the highest abundance at 350 bar and 50 °C. In addition, the presence of other pharmacologically potent sulfur compounds was recorded including S-methyl methanethiosulfinate, diallyl trisulfide, S-methyl methylthiosulfonate, and dimethyl trisulfide. Multivariate data analysis tool was utilized to investigate distributions of the identified compounds among the extracts obtained under various extraction conditions and yields. It was determined that the SC−CO₂ extraction can by efficiently used for A. ursinum.     

Effects of elevated pCO2 on the metabolism of a temperate rhodolith Lithothamnion corallioides grown under different temperatures

Coralline algae are considered among the most sensitive species to near future ocean acidification. We tested the effects of elevated pCO₂ on the metabolism of the free‐living coralline alga Lithothamnion corallioides (“maerl”) and the interactions with changes in temperature. Specimens were collected in North Brittany (France) and grown for 3 months at pCO₂ of 380 (ambient pCO₂), 550, 750, and 1000 μatm (elevated pCO₂) and at successive temperatures of 10°C (ambient temperature in winter), 16°C (ambient temperature in summer), and 19°C (ambient temperature in summer +3°C). At each temperature, gross primary production, respiration (oxygen flux), and calcification (alkalinity flux) rates were assessed in the light and dark. Pigments were determined by HPLC. Chl a, carotene, and zeaxanthin were the three major pigments found in L. corallioides thalli. Elevated pCO₂ did not affect pigment content while temperature slightly decreased zeaxanthin and carotene content at 10°C. Gross production was not affected by temperature but was significantly affected by pCO₂ with an increase between 380 and 550 μatm. Light, dark, and diel (24 h) calcification rates strongly decreased with increasing pCO₂ regardless of the temperature. Although elevated pCO₂ only slightly affected gross production in L. corallioides, diel net calcification was reduced by up to 80% under the 1,000 μatm treatment. Our findings suggested that near future levels of CO₂ will have profound consequences for carbon and carbonate budgets in rhodolith beds and for the sustainability of these habitats.     

Optimization of a corn steep medium for production of ethanol from synthesis gas fermentation by <Emphasis Type="Italic">Clostridium ragsdalei</Emphasis>

Fermentation of biomass derived synthesis gas to ethanol is a sustainable approach that can provide more usable energy and environmental benefits than food-based biofuels. The effects of various medium components on ethanol production by Clostridium ragsdalei utilizing syngas components (CO:CO₂) were investigated, and corn steep liquor (CSL) was used as an inexpensive nutrient source for ethanol production by C. ragsdalei. Elimination of Mg²⁺, NH₄ ⁺ and PO₄ ³⁻ decreased ethanol production from 38 to 3.7, 23 and 5.93 mM, respectively. Eliminating Na⁺, Ca²⁺, and K⁺ or increasing Ca²⁺, Mg²⁺, K⁺, NH₄ ⁺ and PO₄ ³⁻ concentrations had no effect on ethanol production. However, increased Na⁺ concentration (171 mM) inhibited growth and ethanol production. Yeast extract (0.5 g l⁻¹) and trace metals were necessary for growth of C. ragsdalei. CSL alone did not support growth and ethanol production. Nutrients limiting in CSL were trace metals, NH₄ ⁺ and reducing agent (Cys: cysteine sulfide). Supplementation of trace metals, NH₄ ⁺ and CyS to CSL (20 g l⁻¹, wet weight basis) yielded better growth and similar ethanol production as compared to control medium. Using 10 g l⁻¹, the nutritional limitation led to reduced ethanol production. Higher concentrations of CSL (50 and 100 g l⁻¹) were inhibitory for cell growth and ethanol production. The CSL could replace yeast extract, vitamins and minerals (excluding NH₄ ⁺). The optimized CSL medium produced 120 and 50 mM of ethanol and acetate, respectively. The CSL could provide as an inexpensive source of most of the nutrients required for the syngas fermentation, and thus could improve the economics of ethanol production from biomass derived synthesis gas by C. ragsdalei.