Structurally colored thin films of Ca2+-cross-linked alginate

Alginate, or alginic acid, is an unbranched binary copolymer of (1-->4)-linked beta-D-mannuronic acid and alpha-L-guluronic acid. Alginate readily forms binding interactions with a variety of divalent metal ions, such as calcium. This binding has been used to cross-link bulk alginates for a wide variety of applications, particularly in areas of tissue engineering, medical devices, and wound-healing dressings. A new method is identified here for producing Ca2+-cross-linked thin films of sodium alginate, using an aerosolized spray of CaCl2 solution. These thin films exhibit structural color that varies with film thickness. It is demonstrated that this structural color is highly reproducible and can also be tuned to produce a wide range of colored films. The noted ability of alginates to bind metal ions is used in combination with the structural coloration afforded by the thin film structure as a basis for color-based optical sensing of metal ions in aqueous solutions. Changes in film thickness, refractive index, and reflectivity in response to metal ions have been measured and reported. For certain ions such as Cr(III) and Cr(VI), changes in film thickness are the predominate factors in shifting the reflected film color. In the case of other ions such as Pb(II), a change in film refractive index plays a significant role in the reflectance properties of films.     

The contribution of acidulant to the antibacterial activity of acid soluble α- and β-chitosan solutions and their films

This study evaluated individual contributions of dissolving acids (acetic acid, lactic acid, and hydrochloric acid) or acid solubilized chitosan to the antibacterial activity against Listeria innocua and Escherichia coli as solutions and dried films. Solutions containing chitosan showed significantly (P?<?0.05) different inhibitory activity (measured as percentage of inhibition (PI), in percent) against L. innocua and E. coli, compared to equivalent acid solutions. This increase was calculated as additional inhibition (AI, in percent), which could be as high as 65 % in solutions containing 300–320 kDa chitosan depending on the acid type, bacterial species, and the chitosan form (α or β). Solutions containing 4–5 kDa chitosan had lower AI and showed much greater variability among the different chitosan forms, acid types, and bacterial species. Higher molecular weight (Mw) chitosan also showed significantly higher levels of adsorption to bacterial cells than that of lower Mw samples, suggesting that the observed increase in inhibition was the result of surface phenomena. The contribution of acids to the antibacterial activity of chitosan films was assessed by comparing non-rinsed and rinsed films (rinsed in the appropriate broth to remove residual acids and active fragments formed on the dried film). Rinsing β-chitosan films has reduced PI by as much as 28 % compared with non-rinsed films, indicating that part of the antibacterial activity of chitosan films is due to the presence of soluble acid compounds and/or other active fragments. Overall, both acidulant and chitosan were found to contribute to the antibacterial activity of acid solubilized α- and β-chitosan, with the exact antibacterial activity of chitosan varying based on the solution and film properties, suggesting a complex interaction.     

Chitosan–caffeic acid–genipin films presenting enhanced antioxidant activity and stability in acidic media

The use of chitosan films has been limited due to their high degradability in aqueous acidic media. In order to produce chitosan films with high antioxidant activity and insoluble in acid solutions caffeic acid was grafted to chitosan by a radical mechanism using ammonium cerium (IV) nitrate (60 mM). Genipin was used as cross-linker. This methodology originated films with 80% higher antioxidant activity than the pristine film. Also, these films only lost 11% of their mass upon seven days immersion into an aqueous solution at pH 3.5 under stirring. The films surface wettability (contact angle 105°), mechanical properties (68 MPa of tensile strength and 4% of elongation at break), and thermal stability for temperatures lower than 300 °C were not significantly influenced by the covalent linkage of caffeic acid and genipin to chitosan. Due to their characteristics, mainly higher antioxidant activity and lower solubility, these are promising materials to be used as active films.     

Immobilized chitosan as biosorbent for the removal of Cd(II), Cr(III) and Cr(VI) from aqueous solutions

The generation of layer-by-layer silicate-chitosan composite biosorbent was studied. The films were evaluated on its stability regarding the polymer leakage and its capability in the removal of Cd(II), Cr(III) and Cr(VI) from an aqueous solution. SEM, EDAX and ATR-IR techniques were applied for material characterization. Silicate-chitosan films with a final layer of silicate demonstrated chitosan retention and had better sorption capacities than those without it. For metal species, such as Cd(II) and Cr(III), the greatest adsorption was obtained when the pH of the solution was 7. When Cr(VI) was evaluated, pH 4 was the optimal for its adsorption. Langmuir and Freundlich isotherms were modeled for the equilibrium data. An 80% of the adsorbed metal was recovered by HNO(3) incubation. This non-covalent immobilization method allowed chitosan surface retention and did not affect its adsorption properties. The use of a coated surface would facilitate sorbent removal from medium after adsorption.     

Surface modification of chitosan films. Effects of hydrophobicity on protein adsorption

The surface of chitosan films was modified using acid chloride and acid anhydrides. Chemical composition at the film surface was analyzed by attenuated total reflectance Fourier-transform infrared spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS). ATR-FTIR data verified that the substitution took place at the amino groups of chitosan, thus forming amide linkages, and the modification proceeded to the depth at least 1 microm. Choices of molecules substituted at the amino groups of the glucosamine units did affect the hydrophobicity of the film surface, as indicated by air-water contact angle analysis. The surface became more hydrophobic than that of non-modified film when a stearoyl group (C(17)H(35)CO-) was attached to the films. The reaction of chitosan films with succinic anhydride or phthalic anhydride, however, produced more hydrophilic films. Selected modified films were subjected to protein adsorption study. The amount of protein adsorbed, determined by bicinchoninic acid (BCA) assay, related to the types of attached molecules. The improved surface hydrophobicity affected by the stearoyl groups promoted protein adsorption. In contrast, selective adsorption behavior was observed in the case of the chitosan films modified with anhydride derivatives. Lysozyme adsorption was enhanced by H-bonding and charge attraction with the hydrophilic surface. While the amount of albumin adsorbed was decreased possibly due to negative charges that gave rise to repulsion between the modified surface and albumin. This study has demonstrated that it is conceivable to fine-tune surface properties which influence its response to bio-macromolecules by heterogeneous chemical modification.     

Synthesis of UV-curable chitosan derivatives and palladium (II) adsorption behavior on their UV-exposed films

Novel chitosan derivatives with UV-curable functional groups, such as 3-methoxy-4-(2-hydroxy-3-methacryloyloxypropoxy)benzyl, 3,4-bis(2-hydroxy-3-methacryloyloxypropoxy)benzyl, 3-methoxy-4-methacryloyloxybenzyl, and 3,5-dimethacryloyloxybenzyl groups, were prepared. Introduction of photosensitive functional groups to chitosan was accomplished by reductive N-alkylation via Schiff’s bases using corresponding photosensitive aldehydes. Compared to starting chitosan, UV-curable chitosan derivatives showed better solubility in several organic solvents, such as DMSO and 70% methacrylic acid. The solubility of these compounds increased with an increase in the degree of substitution of the N-alkyl side chains. After UV irradiation for 20 s under a high-pressure mercury lamp at a distance of 15 cm from the samples, acidic methanol solutions of these derivatives were transformed to gels in the presence of photo-initiator, and their dried films adsorbed palladium (II) at pH 1.1 and pH 5.3. The UV-curable chitosan derivatives were successfully used as coating materials for electroless plating on non-conductive substances.     

Effect of changes in relative humidity and temperature on ultrathin chitosan films

We have prepared uniform films of chitosan with thicknesses 20 nm < h < 200 nm by spincoating solutions of chitosan dissolved in dilute acetic acid onto silicon substrates while controlling the spin speed and the relative humidity inside the spincoater. After neutralizing the films, they readily absorbed water in the presence of high humidity. Heating of the films to elevated temperatures caused a large irreversible decrease in the film thickness, a small increase in the index of refraction, and a reduction in water absorption, as measured using ellipsometry. Comparisons of infrared absorption measurements of chitosan films collected before and after heating indicate an increase in the degree of acetylation with heating. Collectively, these observations are consistent with the release of bound water and a chemical change similar to acetylation at elevated temperatures.     

Surface structure of chitosan and hybrid chitosan-amylose films-restoration of the antibacterial properties of chitosan in the amylose film

The surface structure of films prepared by casting aqueous solutions of mixtures of water soluble chitosan (WSC) and amylose as well as a fully deacetylated chitosan was studied. Zeta potential measurements indicated that the surface of WSC and fully deacetylated chitosan films is positively charged but very weakly, whereas, a film of amylose blended with WSC exhibited an obvious positive charge. X-ray photoelectron spectra of these films suggest that less amino groups are exposed on the surface of WSC and fully deacetylated chitosan films, whereas, more amino groups are exposed on the surface of a WSC film blended with amylose. A sheet structure in which free amino groups are less exposed on the surface of the film of WSC or fully deacetylated chitosan is proposed. This accounts for the loss of antibacterial activity of chitosan on the WSC film surface. When blended with amylose, the morphology of the film may be disrupted, resulting in strong antibacterial properties.     

Adhesion and growth of HUVEC endothelial cells on films of enzymatically functionalized chitosan with phenolic compounds

Human Umbilical Vein Endothelial Cell (HUVEC) growth on chitosan films and its enzymatically functionalized derivatives films with ferulic acid (FA) and ethyl ferulate (EF) was assessed by evaluating cell adhesion, morphology and cell viability. The results indicated that chitosan derivative films improved protein adsorption properties compared to chitosan films. The HUVEC cell morphology showed well attachment and spread phenotype on chitosan derivative films compared to those growing on chitosan films which did not spread and remained round. Evaluation of cell viability revealed improvement of cell adhesion on chitosan derivative films compared to chitosan film depending on the quantity of oxidized phenols grafted on chitosan. In addition, FA-/EF-chitosan films allowed almost similar cell adhesion. Furthermore, cell adhesion was increased with the film thickness. These results suggested that the oxidized phenols grafting on chitosan is a promising process to enhance cell adhesion, growth and creating useful functional biomaterials.     

Enzymatic hydrolysis of chitosan films in water and physiological solution

It was shown that the processes of enzymatic hydrolysis of chitosan in aqueous acetic acid and on the surface of chitosan films in a solution of hyaluronidase in acetic acid are described by uniform kinetic constants. Kinetic parameters of enzymatic hydrolysis of the chitosan film samples in water and in physiological solution (Ringer–Locke’s solution) were determined. It was found that the introduction of medicinal agents and low-molecular-weight electrolytes to a chitosan-based film material reduces the rate of enzymatic hydrolysis of the films, which may indicate a possible increase in their service life when used on the wound surface.     

Preparation and characterization of polyaniline/chitosan blend film

Films consisting of a blend of a chitosan hydrogel and a conductive polymer, polyaniline (PANI), were prepared and characterized for their electrical and mechanical properties. Polyaniline in emeraldine base (EB) form was dispersed in chitosan solution and blend films were obtained by solution casting. The PANI particles in the blend films were then doped with HCl where we observed reductions in the film tensile strength and Young's modulus by about 30%, but the films electrical conductivity increased by 6 orders of magnitude. The highest electrical conductivity of the blend films was of the order 10⁻⁴ S/cm. The electrical and mechanical properties of the films varied with polyaniline content, acid dopant type, acid dopant concentration, and doping time.     

Novel chitosan-based films cross-linked by genipin with improved physical properties

Novel cross-linked chitosan-based films were prepared using the solution casting technique. A naturally occurring and nontoxic cross-linking agent, genipin, was used to form the chitosan and chitosan/poly(ethylene oxide) (PEO) blend networks, where two types of PEO were used, one with a molecular weight of 20 000 g/mol (HPEO) and the other of 600 g/mol (LPEO). Genipin is used in traditional Chinese medicine and extracted from gardenia fruit. Importantly, it overcomes the problem of physiological toxicity inherent in the use of some common synthetic chemicals as cross-linking agents. The mechanical properties and the stability in water of cross-linked and un-crosslinked chitosan and chitosan/PEO blend films were investigated. It was shown that, compared to the transparent yellow, un-cross-linked chitosan/PEO blend films, the genipin-cross-linked chitosan-based film, blue in color, was more elastic, was more stable, and had better mechanical properties. Genipin-cross-linking produced chitosan networks that were insoluble in acidic and alkaline solutions but were able to swell in these aqueous media. The swelling characteristics of the films exhibit sensitivity to the environmental pH and temperature. The surface properties of the films were also examined by contact angle measurements using water and mixtures of water/ethanol. The results showed that, with the one exception of cross-linked pure chitosan in 100% water, the cross-linked chitosan and chitosan/PEO blends were more hydrophobic than un-crosslinked ones.     

Enzymatic grafting of hexyloxyphenol onto chitosan to alter surface and rheological properties

An enzymatic method to graft hexyloxyphenol onto the biopolymer chitosan was studied. The method employs tyrosinase to convert the phenol into a reactive o-quinone, which undergoes subsequent nonenzymatic reaction with chitosan. Reactions were conducted under heterogeneous conditions using chitosan films and also under homogeneous conditions using aqueous methanolic mixtures capable of dissolving both hexyloxyphenol and chitosan. Tyrosinase was shown to catalyze the oxidation of hexyloxyphenol in such aqueous methanolic solutions. Chemical evidence for covalent grafting onto chitosan was provided by three independent spectroscopic approaches. Specifically, enzymatic modification resulted in (1) the appearance of broad absorbance in the 350-nm region of the UV/vis spectra for chitosan films; (2) changes in the NH bending and stretching regions of chitosan's IR spectra; and (3) a base-soluble material with (1)H-NMR signals characteristic of both chitosan and the alkyl groups of hexyloxyphenol. Hexyloxyphenol modification resulted in dramatic changes in chitosan's functional properties. On the basis of contact angle measurements, heterogeneous modification of a chitosan film yielded a hydrophobic surface. Homogeneously modified chitosan offered rheological properties characteristic of associating water-soluble polymers.     

Covalent immobilization of chitosan and heparin on PLGA surface

Chitosan and heparin were covalently immobilized onto a poly(lactic acid-co-glycolic acid) (PLGA) surface using N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide (EDC), N-hydroxysuccinimide (NHS) in a 2-morpholinoethane sulfonic acid (MES) buffer system. The properties of the modified PLGA surface and the control were investigated by water contact angle measurement and electron spectroscopy for chemical analysis (ESCA). The water contact angle of the modified film was greatly decreased and the element content on the surface of the films changed correspondingly. Platelet adhesion assay showed that blood compatibility of the chitosan/heparin modified film was improved while hepatocyte culture indicated that the cell compatibility of the modified film was enhanced.     

Comparison of the toxicity of heavy metals to cabbage growth

Summary Cabbage plants were grown for 55 days with a nutrient solution containing 1 and 10 ppm of V, Cr(III), Cr(VI), Mn, Fe, Co, Ni, Cu, Zn, Cd, Hg(I), orHg(II). A comparison of the plant growth and chemical analysis revealed that Cr(VI), Cu, Cd, and Hg(II) in the solution are most toxic to the plant growth (hence detrimental to the cabbage-head formation) and Mn, Fe, and Zn are less toxic than other heavy metals, and that Mn, Zn, Co, Ni, and Cd and translocated into all the plant organs while V, Cr(III), Cr(VI), Fe, Cu, Hg(I), and Hg(II) are accumulated in the roots.     

Effect of molecular weight of chitosan on antimicrobial properties and tissue compatibility of chitosan-impregnated bacterial cellulose films

Bacterial cellulose-chitosan (BC-C) films were developed by immersing purified BC pellicles in 1.5 ~ 2.0% (w/v) acetic acid solutions containing chitosan of varying molecular weights. Effects of different molecular weight of chitosan on physical, biological and antimicrobial properties of the composite films were investigated. The cumulative chitosan absorption capacities with M_w of 141,000, 199,000, and 263,000 were 38.43, 24.65, and 23.89 mg/cm³ of dry BC film, respectively. The cumulative release profiles of chitosan from the films strongly depended on molecular weight of chitosan and pH of solution. The order of release of chitosan from the BC-C films was dependent on molecular weight as follows: M_w 141,000 > M_w 199,000 > M_w 263,000. All BC-C films showed the antimicrobial abilities against Staphylococcus aureus and Aspergillus niger but had no inhibitory effect on the growth of Escherichia coli. The BC-C films supported for adhesion, spreading and proliferation of both human skin keratinocytes and fibroblasts. The antibacterial activity against S. aureus of the BC-C with the highest Mw chitosan (263,000) was higher than those of the others. On the other hand, the BC-C films with the lowest M_w chitosan (141,000) promoted the growth of human skin cells more than those of the others.     

Chitosan film containing fucoidan as a wound dressing for dermal burn healing: Preparation and in vitro/in vivo evaluation

The aim of this study was to develop chitosan film containing fucoidan and to investigate its suitability for the treatment of dermal burns on rabbits. Porous films, thickness between 29.7 and 269.0 μm, were obtained by the solvent dropping method. Water vapor permeability (3.3–16.6/0.1 g), the swelling (0.67–1.77 g/g), tensile strength (7.1–45.8 N), and bioadhesion (0.076–1.771 mJ/cm²) of the films were determined. The thinnest films were obtained with the lowest chitosan concentration (P<.05). The water absorption capacity of the films sharply increased with the freeze-drying technique. The film having the thickness of 29.7 μm showed the highest amount of moisture permeability (16.6 g/0.1 g). Higher chitosan concentration significantly increased tensile strength of the films (P<.05). Using higher concentration of lactic acid made films more elastic and applicable, and these films were selected for in vivo studies. Seven adult male New Zealand white rabbits were used for the evaluation of the films on superficial dermal burns. Biopsy samples were taken at 7, 14, and 21 days after wounding, and each wound site was examined macroscopically and histopathologically. After 7 days treatment, fibroplasia and scar were observed on wounds treated with fucoidan-chitosan film. The best regenerated dermal papillary formation, best reepithelization, and the fastest closure of wounds were found in the fucoidan-chitosan film treatment group after 14 days compared with other treatment and control groups. It can be concluded that fucoidan-chitosan films might be a potential treatment system for dermal burns and that changing formulation variables can modulate the characterizations of the films. Published: May 24, 2007     

Metal complexes of the antibiotic nalidixic acid

The preparations and spectral properties are reported of a range of complexes of nalidixic acid (= HNal) with some metal ions in the series CrZn and also Mg, Ca, Cd, Hg and Pd(II). Most of the compounds formed by the divalent metal ions had a 2:1 HNal:metal ratio, and some of them are polymeric. Complexes in which the carboxylate group of HNal functions as a chelate were isolated with Cu(II), Pd(II), Fe(III) and Cr(III).     

Electrostatic adsorption of heme proteins alternated with polyamidoamine dendrimers for layer-by-layer assembly of electroactive films

A novel thin film of heme proteins, including hemoglobin (Hb), myoglobin (Mb), and catalase (Cat), was successfully assembled layer by layer with polyamidoamine (PAMAM) dendrimers on different solid surfaces. At pH 7.0, protonated PAMAM possesses positive surface charges, whereas the proteins have net negative surface charges at pH above their isoelectric points. Thus, layer-by-layer {PAMAM/protein}(n)() films were assembled with alternate adsorption of oppositely charged PAMAM and proteins from their aqueous solutions mainly by electrostatic interaction. The assembly process was monitored by quartz crystal microbalance (QCM), UV-vis spectroscopy, and cyclic voltammetry (CV). The growth of the protein multilayer films was regular and linear, whereas the electroactivity of the films was only extended to a few bilayers. CVs of {PAMAM/protein}(n)() films showed a pair of well-defined and nearly reversible peaks characteristic of the protein heme Fe(III)/Fe(II) redox couples. Although {PAMAM/Hb}(n)() and {PAMAM/Mb}(n)() films showed very similar properties, {PAMAM/Cat}(n)() films displayed different and unique characters. The substrates with biological or environmental significance, such as oxygen, hydrogen peroxide, trichloroacetic acid, and nitrite, were catalytically reduced at {PAMAM/protein}(n)() film electrodes, showing the potential applicability of the films as new types of biosensors or bioreactors based on direct electrochemistry of the proteins. Both the electrochemical and electrocatalytic activity of {PAMAM/protein}(n)() films can be tailored precisely by controlling the number of bilayers or the film thickness.     

Mechanical properties of chitosan/bamboo charcoal composite films made with normal and surface oxidized charcoal

Chitosan/bamboo charcoal composite films were prepared by blending chitosan with either virgin bamboo charcoal or bamboo charcoal modified by nitric acid oxidation to provide more hydrophilic regions on the bamboo charcoal surface. Investigation of the physical properties of these composite films revealed that the tensile strength and Young’s modulus of the chitosan films were enhanced in a dose-dependent manner by the inclusion of modified bamboo charcoal at up to 1% (w/w), whilst the elongation at break was increased by inclusion of modified bamboo charcoal at up to 0.5% (w/w). In contrast, chitosan composites with virgin bamboo charcoal at up to 0.5% or 1.0% (w/w) showed no enhancement of the tensile strength or Young’s modulus, respectively, and both parameters were reduced with higher levels of virgin bamboo charcoal. Oil, and especially water, absorption of the composite films displayed a marked and dose-dependent increase compared to those of the pure chitosan film.