A Holder for Simultaneous Fluid Processing or Carbon Coating of Electron Microscope Grids in Lots of 10 or More

A piece of polyethylene tubing about 14 cm long, ID 3 mm and with a 1.5 mm wall is shaped to hold grids in a linear series as follows. A series of pairs of transverse cuts I mm apart are made across and about $3/4 through the tubing at intervals of 1 cm. After making diagonal cuts on either side of each pair of cuts, wedge-shaped pieces of tubing are removed to leave free-standing 1 mm widths of the tubing wall. Each arch of wall is then bisected by a cut in the longitudinal direction of the tubing, thus providing the jaws of a clamp for a grid. By spreading the jaws with forceps, the grid can be inserted. On removal of the forceps, the grid is held firmly and when the holder is filled, the grids face in a direction perpendicular to its long dimension. By inserting a piece of glass tubing into the lumen of the holder, it is held straight and can be placed in a test tube for fluid processing. Stains or other fluids can be introduced through the glass tube, thus allowing fluid changes without exposure to air. Carbon coating can be achieved without removing the grids, since they all face the same way. For convenience in loading and unloading, the holder can be temporarily attached to a base with double-coated adhesive tape.     

A Mechanical Device for Retrieving Ribbons of Ultrathin Sections Without Folds

An improved version of a mechanical device for retrieving ribbons of ultrathin sections free of wrinkles is described. The device is simple and easy to use and can be used by both right- and left-handed operators. A grid is grasped by forceps which are held in position by a magnet in such a way that it can be lowered into the water well behind the floating sections. After a ribbon has been properly aligned, moved to the grid and fastened by an end-section, the grid with the sections is slowly drawn up and out of the water with a rack-and-pinion mechanism.     

Double Embedding Broad Thin Leaves in Paraffin

Paraffin pellets were melted in 24 × 24 × 5 mm stainless steel base molds. Specimens of leaves, 18 × 18 mm, were fixed, dehydrated and infiltrated with paraffin. Two specimens were transferred into molten paraffin on their laminar surfaces in a base mold and moved quickly onto a cold surface to cast them in a shallow block of paraffin. Each block was then scored with a razor blade, broken into two primary blocks, and trimmed to 20 × 9 mm with 5 mm flat edges. Each primary block was immersed upright on its long edge in a 22 × 22 × 20 mm Peel-A-Way® embedding mold containing molten paraffin. The leaf edge was held centrally in the mold while moving the double embedment onto a cold surface. In this secondary block, the leaf specimen stood perpendicular to the sectioning surface in perfect orientation for transverse ribbon sectioning. The two phases of paraffin bonded well.     

Grid Staining—A Useful Device

A simple and disposable holder for electron microscope grids can be constructed from discs of silicon rubber. The discs (10 mm thick × 25 mm diameter) arc scored 0.4 mm deep with a razor. Flexing the discs opens the scorns for insertion of grids. Staining wells can be made from polyethylene snap-in vial tops by cutting away the nipple-like portion. After impaling the holders on the tips of a pair of forceps the grids can be washed by immersion. This holder is rigid, inert and inexpensive. It is of particular advantage for handling single-slotted grids.     

Method for Staining and Washing Thin Sections on Support Films

A procedure is described for staining large numbers of thin sections on support films for use with one-hole grids. The film is picked up, carried and protected using easily made plastic blocks. Loop-tipped forceps are then used to transfer tissue ribbons from the knife boat to the support film. A large number of tissue sections can then be stained and washed simultaneously in a modified Pyrex dish without damaging the film. After staining, the slot in the one-hole grid is centered over the tissue ribbon, and the grid is attached to the film. The method is suitable for serial reconstruction and the unobstructed viewing of large thin sections in the TEM.     

Association and dissociation of the thick and thin filaments within myofibrils in conditions of “contraction” and “relaxation”

1. The current assumption that the low ATPase activity of relaxed myofibrils is represented by the ATPase activity of myosin which has been set free during the dissociation of actomyosin was investigated. For this purpose, the ATPase activity of relaxed skeletal myofibrils of the rabbit and of the crab Maia squinado has been compared with the activity of contracted fibrils and of purified rabbit myosin in conditions of varying ionic strength, pH and concentrations of MgATP (i.e. MgATP²⁻ + MgHATP⁻) and Mg²⁺.

2. Contraction and relaxation of the fibrils was induced by changing the concentration of Ca²⁺ from about 5×10⁻⁵ to below 1×10⁻⁸ M.

3. In all conditions studied, the ATPase activity of relaxed fibrils was about 6–8 times less than that of the contracted fibrils, but it remained a typical actomyosin ATPase.

4. Quantitatively and qualitatively, this ATPase differs from the ATPase of myosin. For instance, its dependence on pH is the reverse of that of the myosin ATPase.

5. Calculation showed that the fibrils are dissociated by 90% in conditions of relaxation. Since the ATPase activity of myosin was merely some 2% of the actomyosin activity, the major part of the ATPase of fibrils, even at a dissociation of 90%, is bound to show the properties of the ATPase of actomyosin.

6. However, a dissociation of 90% cannot be distinguished from a dissociation of 100% by means of physical methods (viscosity, superprecipitation, resistance to stretch, etc.). This explains why physical methods indicate a “full” dissociation of actomyosin although, enzymatically, the ATPase is still of the actomyosin type.

7. The possible reasons are discussed for the discrepancy between the 100-fold increase in the ATP turnover and the 1000-fold increase in energy turnover of the living muscle during the transition from relaxed to active state. The most probable explanation seems to be an ATPase activity of myosin which is too high by a factor of ten as compared to the energy turnover of living muscle at the resting state. This high activity cannot be caused by a contamination of the myosin by Ca²⁺-insensitive actomyosin.     

A Numbered-Grid Locator Slide for Relocating Microscopic Fields

Four strips of drawing paper, each 22 × 30 cm, are taken. Numbers are typed from a typewriter with elite type face in such a way that, when pasted side by side along their lengths on another sheet of drawing paper, they yield a 88 × 30 cm master copy carrying numbers commencing from 1001 at top left and ending with 6680 at bottom right, each number preceded and succeeded by a dot. The upper and lower edges of this rectangle containing these figures are then extended by lines 2 cm each to the left and the ends jointed to make up a 90 × 30 cm master copy from which a 3 × 1 inch (7.5 × 2.5 cm) slide is prepared by photographic reduction. To use this slide, the microscopic field is found, the slide carrying the tissue is exactly replaced by the locator slide, and the number recorded. For subsequent reference, the procedure is reversed by first finding the number and then replacing the locator slide by the one bearing the tissue     

The Membrane Method of Electron Microscope Autoradiography

Thin sections of methacrylate and Araldite embedded tissues labelled with radioactive isotopes were transferred with a wire loop or brush from the knife edge onto thin formvar membranes which covered 7 mm holes in 76 × 25 × 1.5 mm or 76 × 38 × 1.5 mm plastic slides. To facilitate the mounting of sections, a platform supported the plastic slides close to the ultramicrotome knife. Photographic emulsion diluted 1:5 or 1:10 with water was applied with a pipette to the upper surface of each formvar membrane to cover the mounted sections. Excess emulsion was drained off and the remaining thin film was dried on a warm plate at 45 C to produce a uniform layer over the sections. After storing in the dark for several weeks, preparations were processed in photographic solutions and washed, and sometimes stained, before applying electron microscope grids to the underside of each formvar membrane. To detach each grid with its adherent formvar, section and emulsion, the membrane was pierced around the perimeter of the grid. Grain counts made over nuclei of cells labelled with tritiated thymidine indicate that emulsion is uniformly distributed over each section and that quantitative comparison is possible between labelled areas.     

A new tool based on two micromanipulators facilitates the handling of ultrathin cryosection ribbons

A close to native structure of bulk biological specimens can be imaged by cryo-electron microscopy of vitreous sections (CEMOVIS). In some cases structural information can be combined with X-ray data leading to atomic resolution in situ. However, CEMOVIS is not routinely used. The two critical steps consist of producing a frozen section ribbon of a few millimeters in length and transferring the ribbon onto an electron microscopy grid. During these steps, the first sections of the ribbon are wrapped around an eyelash (unwrapping is frequent). When a ribbon is sufficiently attached to the eyelash, the operator must guide the nascent ribbon. Steady hands are required. Shaking or overstretching may break the ribbon. In turn, the ribbon immediately wraps around itself or flies away and thereby becomes unusable. Micromanipulators for eyelashes and grids as well as ionizers to attach section ribbons to grids were proposed. The rate of successful ribbon collection, however, remained low for most operators. Here we present a setup composed of two micromanipulators. One of the micromanipulators guides an electrically conductive fiber to which the ribbon sticks with unprecedented efficiency in comparison to a not conductive eyelash. The second micromanipulator positions the grid beneath the newly formed section ribbon and with the help of an ionizer the ribbon is attached to the grid. Although manipulations are greatly facilitated, sectioning artifacts remain but the likelihood to investigate high quality sections is significantly increased due to the large number of sections that can be produced with the reported tool.     

适用于磁压榨吻合的平移钳的设计

目的:提出了磁压榨吻合操作中可用于磁体夹持固定的平移钳的结构设计方案。方法:分析本团队多种原创性磁压榨吻合技术操作中存在的缺陷和不足,认为目前磁压榨吻合操作中依靠术者徒手控制或利用现有血管钳对磁体进行夹持和固定,是造成操作中诸多不便的主要原因。从力学角度分析了常规血管钳夹持磁体易导致磁体滑脱的原因,指出设计加工磁吻合专用钳是解决目前磁吻合操作不便的有效措施。在此基础上提出了利用平移钳来固定磁体的结构设计方案,并从力学角度进行了受力分析,设计出了用于磁压榨吻合操作中磁体夹持固定的平移钳。结果:平移钳的结构设计能够稳定夹持磁体,避免磁体滑脱;同时,借助齿轮传动结构控制钳头的平行移动能够更好地控制磁体的精准对吸和分离,可进一步简化操作,避免副损伤,节省手术操作时间。结论:平移钳能满足多种形状及大小的磁体的夹持和固定,可有效控制磁体的吸合与分离,极大地方便操作。该平移钳加工简单,使用方便,有助于推动磁压榨吻合技术在临床广泛开展。     

Dystrophin in rod spherules; submembranous dense regions facing bipolar cell processes

 It is known that the retina contains the protein dystrophin in the ribbon synapse, but the ultrastructural analysis is not yet fully elucidated. Our previous study reported that dystrophin is localized under the rod cell membranes in rat retinas. In the present study, we have investigated the relationship between dystrophin-rich regions of rod cell membranes and other neuronal processes in mouse retinas with a monoclonal antibody raised against the human dystrophin C-terminus. Immunoblotting, immunofluorescence stainings, and immunoelectron microscopy were employed. Immunoblotting analysis indicated that mouse retinas possessed some of the dystrophin isoforms of approximately 260 kDa, 140 kDa, and 70 kDa molecular weight. Confocal images showed a punctate appearance in the outer plexiform layer, as previously described. Immunoelectron microscopy showed that dystrophin immunoreactive products were always observed at submembranous dense regions of the rod spherule abutting bipolar processes. These results suggest that retinal dystrophin may be closely involved in signal transmission from rods to bipolar cells. Accepted: 7 May 1997     

Photographic Mapping of a Tissue Surface to Locate Fields for Electron Microscopy; Mouse Lung

Precise sampling from whole lobes of mouse lungs fixed in the inflated state and embedded in epoxy resin can be not only feasible but also efficient. A 1 μm section is cut from an embedded lobe with a rotary microtome and a steel knife. This section is stained and photographed, and from it a 35 × enlarged print is prepared. A grid of transparent plastic scored with 35 mm squares, lettered vertically and numbered horizontally, is superimposed over the photograph. The area chosen for electron microscopy thus becomes identifiable by a letter-number designation obtained from the grid. This area is then located by light microscopy on a 2 mm slice taken from the block from which the 1 μm section was cut, by use of oblique illumination and the calibrated mechanical stage of the light microscope. A block of 1.3 mm diameter is removed for electron microscopy from the tissue by a rotatable circular spring-loaded punch screwed into the objective turret of the microscope. The removed cylinder is mounted on a metal stub and ultrathin sections cut from the faced tissue. The method is as equally suitable for the examination of other tissues, particularly when large areas and multiple sampling may be required.     

Maillard induced complexes of bovine serum albumin - a dilute solution study

Association of bovine serum albumin (BSA) on heating in the presence and absence of 2% xylose has been studied using dynamic light scattering and sedimentation velocity. When 3% solutions of the protein alone are heated at 95°C association products are formed with molar masses of 2 × 10⁶g/mol, a value which is independent of the time of heating. These aggregates can be dissociated in solvents that disrupt non-covalent bonds. When the reducing sugar xylose is present there is a continuous change in the hydrodynamic properties with time. After 80 min a molar mass in excess of 7 × 10⁶g/mol is obtained. This increase in molar mass is attributed to additional non-disulphide linkages resulting from the Maillard reaction. Information about the gross conformation of the Maillard induced association products has been obtained from MHKS (Mark-Houwink-Kuhn-Sakarada) double logarithmic plots of D_20,w and s_20,w against molar mass. The values of the MHKS coefficients obtained are most consistent with a linear rod: i.e. the association is of an end-to-end type     

Instrumented forceps for measuring tensile forces in the rod of the VDS implant during correction of scoliosis.

Ventral derotation spondylodesis (VDS) is the standard in ventral scoliosis surgery. Especially in the thoracic spine, there are no alternatives to VDS with compression and derotation as its correction forces. However, pull-out of the end-vertebra screw during correction of scoliosis with the VDS implant is a common complication involving particularly the cranial end-vertebra screw in the thoracic region. This complication requires an extension of the fusion length or reduces at least the outcome of the correction. There are no in vivo data on correction forces in ventral scoliosis surgery. Thus the correction depends on the skill and experience of the surgeon. An instrumented forceps developed and built to measure forces in the longitudinal rod allows axial tensile forces to be determined in the longitudinal rod during surgery. The instrumented forceps has the advantage of reducing the risk of screw pull-out. Furthermore, viscoelastic behavior of the spine can be measured during ventral correction. In addition, knowledge of the correction forces improves our biomechanical understanding of the spine, especially during correction of scoliosis. Intraoperative force measurement is in no way detrimental to the patient.     

Glutathione-proline activation of feeding behavior in the zoanthid Palythoa psammophilia Walsh & Bowers

Palythoa psammophilia Walsh & Bowers has a well coordinated, stereotyped feeding response, the culminating step of which is ingestion; this may be elicited by the synergistic effect of the tripeptide glutathione and the -imino acid, proline. Either activator acting separately causes responses only at high concentrations (above 10⁻⁵ M for glutathione; above 10⁻⁴ M for proline) in a reduced number of animals and at a low rate (5.00 ± 1.73 min in 5 × 10⁻³ M solutions of glutathione; 11.10±3.74 min in 5 × 10⁻³ M solutions of proline). Highest percentages of response were obtained in combinations where glutathione was at a concentration of 5 × 10⁻³ M and proline at 5 × 10⁻⁴ M or in combinations of glutathione at concentrations 5 × 10⁻⁶ M and proline at 5 × 10⁻⁵ M. The speed of ingestion is considerably enhanced when these activators are combined (1.17±1.18 min).     

Selection for Electron Microscopy of Specific Areas in Large Epoxy Tissue Sections

Tissue blocks 2 × 2 × 0.4 cm were fixed 6-24 hr in phosphate-buffered 6% glutaraldehyde then sliced to 2 × 2 × 0.1 cm and rinsed in phosphate buffer for at least 12 hr. Fixation was continued for 2 hr in phosphate-buffered 1-2% OsO₄. The slices were dehydrated, infiltrated with Araldite, and embedded in flat-bottomed plastic molds. Sectioning at 4-8 μ with a sliding microtome was facilitated by addition of 10% dibutylphalate to the standard epoxy mixture. The sections were spread on water and attached to coverslips by drying, then heating to 80 C for 1 min. Staining 2 min with 1-3% KMnO₄ and temporary mounting in glycerol on a slide allowed the desired area for electron microscopy to be selected and marked. This area was then cemented to the facet of a conventional epoxy casting with a drop of epoxy resin (without added dibutylphthalate). After polymerization, the coverslip was removed by quick cooling leaving a flat re-embedded portion of the original section. This portion was viewed by transillumination in a dissecting microscope and trimmed of surplus tissue. Ultrathin sections for electron microscopy were obtained in the usual manner.     

A Remodeled Tissue Flattener for Use with the International Microtome Cryostat

The antiroll plate is cut from a standard microscope slide, a 2 cm length, to give a 2 × 2.5 cm piece. This is fitted into inside grooves of a movable metal frame which is held by a hinge joint parallel to the back of the microtome knife. A stationary frame, which supports the hinged member, has spring clips welded to its sides for attachment to the knife. Clearance between the antiroll plate and knife is obtained by applying Scotch tape to the edge of the plate that is adjacent to the knife edge. The hinge permits the plate to be swung back and thus clear the knife surface.     

The Role of Wheel Running in the Coupling of Two Simultaneous Circadian Rhythms of Motor Activity in the Rat

Motor activity is among the non-photic stimuli that act on the internal clock. We have tested the role of motor activity in the circadian pattern of rats under conditions near the lower limits of entrainment, that induce circadian rhythm dissociation. Three groups of 8 rats each were used: a) rats kept individually in 25×25×15 cm cages, b) rats in 50×25×15 cm cages, and c) rats in 50×25×15 cm cages with access to a running wheel. All the rats were kept under light-dark cycles of 22 hours (T22, 11L:11D) for 50 days, after which they were transferred to constant darkness. All the rats without a running wheel showed a motor activity pattern with two statistically significant circadian rhythms in the periodogram of Sokolove and Bushell: one circadian component entrained by the LD cycle, and another free-running. The rats with access to a running wheel showed several patterns: 5 rats showed only one rhythm entrained to the LD cycle, 2 rats showed circadian rhythm dissociation, and 1 showed only a free running rhythm. We believe that the simultaneous manifestation of two circadian components reflects the functional dissociation of the oscillators population that constitutes the circadian pacemaker, of the rat. Physical exercise acts on the pacemaker reinforcing the strongest group of oscillators, which, depending on the structure of the circadian system of the rat, is usually the one entrained to the LD cycle. This study supports the hypothesis that motor activity couples the oscillators that form the circadian system of the rat.     

Using Scrapings from Formalin-Fixed Tissues to Diagnose Leptospirosis by Fluorescent-Antibody Techniques

Small specimens of formalin-fixed tissues approximatey 1 × 1 × 0.2 cm were cut from the suspect specimen. Several clean microscope slides were dipped in 1% aqueous gelatin and air-dried or dried on a slide warmer. Each tissue specimen was washed in running tap water for 2-5 min and then lightly scraped with a straight knife blade, cutting edge perpendicular to the surface of the specimen. The scrapings were allowed to build up and cling to the knife blade, which was then turned so that the broad surface contacted the slide; thus, the scrapings could be smeared onto the slide in a single motion. Sufficient pressure was applied to embed the tissue fragments in the gelatin coating. Smears, dried in air or on a slide warmer, were stained immediately by a standard direct or indirect technique to detect fluorescein-labeled antigens. This scraping method, adapted to the study of leptospirosis by fluorescent-antibody technique, could reduce the need for cryostat-cut tissues and facilitate the observation of individual leptospires.