Amperometric acetylcholine sensor catalyzed by nickel anode electrode

An amperometric method was using a nickel catalytic electrode in aqueous base solution for detecting acetylcholine (ACh). A sensing mechanism was developed in which ACh was hydrolyzed in base aqueous solution to produce the acetic anion and choline. The alcohol group of choline was oxidized to the corresponding carboxylic acid by Ni(OH)2/NiOOH catalytic system. The amperometric response resulted from the current generated by ACh oxidation in response to step changes in ACh concentration. The potential window of limiting current of ACh anodic oxidation at the Ni interface was determined in NaOH electrolyte. The effect of NaOH electrolyte concentration on sensitivity was also discussed. At the optimum operating condition, the method exhibits a good linear relationship between the response current and the ACh concentration. The response time of the ACh sensing system was 10 s. Scanning electrochemical microscopy (SECM) with platinum micro-tips was used to investigate the diffusion layer thickness of Ni electrode.     

Direct electrochemistry and electrocatalytic activity of catalase immobilized onto electrodeposited nano-scale islands of nickel oxide

Cyclic voltammetry was used for simultaneous formation and immobilization of nickel oxide nano-scale islands and catalase on glassy carbon electrode. Electrodeposited nickel oxide may be a promising material for enzyme immobilization owing to its high biocompatibility and large surface. The catalase films assembled on nickel oxide exhibited a pair of well defined, stable and nearly reversible CV peaks at about -0.05 V vs. SCE at pH 7, characteristic of the heme Fe (III)/Fe (II) redox couple. The formal potential of catalase in nickel oxide film were linearly varied in the range 1-12 with slope of 58.426 mV/pH, indicating that the electron transfer is accompanied by single proton transportation. The electron transfer between catalase and electrode surface, (k(s)) of 3.7(+/-0.1) s(-1) was greatly facilitated in the microenvironment of nickel oxide film. The electrocatalytic reduction of hydrogen peroxide at glassy carbon electrode modified with nickel oxide nano-scale islands and catalase enzyme has been studied. The embedded catalase in NiO nanoparticles showed excellent electrocatalytic activity toward hydrogen peroxide reduction. Also the modified rotating disk electrode shows good analytical performance for amperometric determination of hydrogen peroxide. The resultant catalase/nickel oxide modified glassy carbon electrodes exhibited fast amperometric response (within 2 s) to hydrogen peroxide reduction (with a linear range from 1 microM to 1 mM), excellent stability, long term life and good reproducibility. The apparent Michaelis-Menten constant is calculated to be 0.96(+/-0.05)mM, which shows a large catalytic activity of catalase in the nickel oxide film toward hydrogen peroxide. The excellent electrochemical reversibility of redox couple, high stability, technical simplicity, lake of need for mediators and short preparations times are advantages of this electrode. Finally the activity of biosensor for nitrite reduction was also investigated.     

Highly sensitive sensor for picomolar detection of insulin at physiological pH, using GC electrode modified with guanine and electrodeposited nickel oxide nanoparticles

The electrochemical behavior of insulin at glassy carbon (GC) electrode modified with nickel oxide nanoparticles and guanine was investigated. Cyclic voltammetry technique has been used for electrodeposition of nickel oxide nanoparticles (NiOx) and immobilization of guanine on the surface GC electrode. In comparison to glassy carbon electrode modified with nickel oxide nanoparticles and bare GC electrode modified with adsorbed guanine, the guanine/nickel oxide nanoparticles/modified GC electrode exhibited excellent catalytic activity for the oxidation of insulin in physiological pH solutions at reduced overpotential. The modified electrode was applied for insulin detection using cyclic voltammetry or hydrodynamic amperometry techniques. It was found that the calibration curve was linear up to 4muM with a detection limit of 22pM and sensitivity of 100.9pA/pM under the optimized condition for hydrodynamic amperometry using a rotating disk modified electrode. In comparison to other electrochemical insulin sensors, this sensor shows many advantages such as simple preparation method without using any special electron transfer mediator or specific reagent, high sensitivity, excellent catalytic activity at physiological pH values, short response time, long-term stability and remarkable antifouling property toward insulin and its oxidation product. Additionally, it is promising for the monitoring of insulin in chromatographic effluents.     

A novel impedimetric aptasensor,based on functionalized carbon nanotubes and prussian blue as labels

A simple and feasible electrochemical sensing protocol was developed for the detection of bisphenol A (BPA) by employing the gold nanoparticles (AuNPs), prussian blue (PB) and functionalized carbon nanotubes (AuNPs/PB/CNTs-COOH). An aminated complementary DNA as a capture probe and specific aptamer against BPA as a detection probe was immobilized on the surface of a modified glassy carbon (GC) electrode via the formation of covalent amide bond and hybridization, respectively. The proposed nanoaptasensor combined the advantages of the in situ formation of PB as a label, the deposition of neatly arranged AuNPs, and the covalent attachment of the capture probe to the surface of the modified electrode. Upon addition of target BPA, the analyte reacted with the aptamer and caused the steric/conformational restrictions on the sensing interface. The formation of BPA–aptamer complex at the electrode surface retarded the interfacial electron transfer reaction of the PB as a probe. Sensitive quantitative detection of BPA was carried out based on the variation of electron transfer resistance which relevant to the formation of BPA– aptamer complex at the modified electrode surface. Under the optimized conditions, the proposed aptasensor exhibited a high sensitivity, wide linearity to BPA and low detection limit. This aptasensor also displayed a satisfying electrochemical performance with good stability, selectivity and reproducibility.     

Fundamental studies of the cytochrome c immobilization by the potential cycling method on nanometer-scale nickel oxide surfaces

This work describes the performance of cytochrome c/nickel oxide nanoparticles/glassy carbon electrode, prepared by the electrochemical deposition of the nickel oxide nanoparticles (NiO NPs) on the glassy carbon (GC) electrode surface and the cytochrome c immobilization on the nickel oxide nanoparticle surfaces. An extensive sample examination with the help of the SEM and AFM presented the existence of different geometrical shapes of the nickel oxide particles. These geometrical structures could lead to the better immobilization of proteins on their surfaces. The resulting electrode displayed an excellent behavior for the redox of the cytochrome c. Also, the resulting heme protein exhibited a direct electrical contact with the electrode because of the structural alignment of the heme protein on the nanometer-scale nickel oxide surfaces. This method could be suitable for applications to nanofabricated devices. In the end, it was concluded that the cytochrome c could be tethered to the nanometer-scale nickel oxide surfaces.     

Nonenzymatic electrochemical detection of glucose using well-distributed nickel nanoparticles on straight multi-walled carbon nanotubes

A nonenzymatic electrochemical sensor device was fabricated for glucose detection based on nickel nanoparticles (NiNPs)/straight multi-walled carbon nanotubes (SMWNTs) nanohybrids, which were synthesized through in situ precipitation procedure. SMWNTs can be easily dispersed in solution after mild sonication pretreatment, which facilitates the precursor of NiNPs binding to their surface and results in the homogeneous distribution of NiNPs on the surface of SMWNTs. The morphology and component of the nanohybrids were characterized by scanning electron microscopy (SEM) and X-ray powder diffraction (XRD), respectively. Cyclic voltammetry (CV) and amperometry were used to evaluate the catalytic activity of the NiNPs/SMWNTs nanohybrids modified electrode towards glucose. It was found that the nanohybrids modified electrode showed remarkably enhanced electrocatalytic activity towards the oxidation of glucose in alkaline solution compared to that of the bare glass carbon electrode (GCE), the NiNPs and the SMWNTs modified electrode, attributing to the synergistic effect of SMWNTs and Ni²⁺/Ni³⁺ redox couple. Under the optimal detection conditions, the as-prepared sensors exhibited linear behavior in the concentration range from 1 μM to 1 mM for the quantification of glucose with a limit of detection of 500 nM (3σ). Moreover, the NiNPs/SMWNTs modified electrode was also relatively insensitive to commonly interfering species such as ascorbic acid (AA), uric acid (UA), dopamine (DA), galactose (GA), and xylose (XY). The robust selectivities, sensitivities, and stabilities determined experimentally indicated the great potential of NiNPs/SMWNTs nanohybrids for construction of a variety of electrochemical sensors.     

Amperometric detection of insulin at renewable sol-gel derived carbon ceramic electrode modified with nickel powder and potassium octacyanomolybdate(IV)

A renewable three-dimensional chemically modified carbon ceramic electrode (CCE) containing nickel powder and K4[Mo(CN)8] was constructed by sol-gel technique. The electrochemical properties and stability of modified electrode was evaluated by cyclic voltammetry in pH range 4-10. The redox couple of [Mo(CN)8] (4-/3-) was shown both as a solute in electrolyte solution and as a component of a carbon based conducting composite electrode. The apparent electron transfer rate constant (ks) and transfer coefficient (alpha) were determined by cyclic voltammetry and they were about 17.1 and 0.57 s(-1), respectively. The catalytic activity of the modified CCE toward insulin oxidation was investigated at pH range of 3-8 by cyclic votammetry. The modified electrode showed excellent electrocatalytic activity toward insulin electroxidation at physiological pH value. The modified electrode was used for insulin detection chronoamperometrically at pH 7. Under optimized condition in amperometry method, the concentration calibration range, detection limit and sensitivity were 0.5-500 nM, 0.45 nM and 6140 nA/microM, respectively. Flow injection amperometric determination of insulin at pH 7.4, at this modified electrode yielded a calibration curve with the following characteristics, linear dynamic range 100-500 pM; sensitivity 8.1 nA/nM and detection limit 40 pM (based on S/N = 3). The inherent stability at wide pH range, high sensitivity, low detection limit, low cost and ease of preparation are of advantageous of this insulin sensor. This sensor indicates great promise for monitory insulin in chromatographic effluents.     

Amperometric ascorbic acid sensor based on doped ferrites nanoparticles modified glassy carbon paste electrode

In this study, a novel electrochemical sensor for quantification of ascorbic acid with amperometric detection in physiological conditions was constructed. For this purpose, cobalt and nickel ferrites were synthesized using microwave and ultrasound assistance, characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and X-ray powder diffraction (XRPD), and used for modification of glassy carbon paste electrode (GCPE). It was shown that introducing these nanoparticles to the structure of GCPE led to increasing analytical performance. Co ferrite modified GCPE (CoFeGCPE) showed better characteristics toward ascorbic acid sensing. The limit of detection (LOD) obtained by sensor was calculated to be 0.0270 mg/L, with linear range from 0.1758 to 2.6010 mg/L. This sensor was successfully applied for practical analysis, and the obtained results demonstrated that the proposed procedure could be a promising replacement for the conventional electrode materials and time-consuming and expensive separation methods.     

Electrocatalytic oxidation and determination of deferasirox and deferiprone on a nickel oxyhydroxide-modified electrode

The electrocatalytic oxidation of two orally administered iron chelator drugs (deferiprone, CP20, and deferasirox, ICL670) was investigated on a nickel oxyhydroxide-modified nickel electrode in alkaline solution. The oxidation process involved and its kinetics were investigated using cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy techniques, as well as steady-state polarization measurements. Voltammetric studies indicated that in the presence of the drugs under study, the anodic peak current of low-valence nickel species increased, followed by a decrease in the corresponding cathodic current. This result indicates that the drugs were oxidized via oxyhydroxide species immobilized on the electrode surface via an EC' mechanism. A mechanism based on the electrochemical generation of Ni(III) active sites and their subsequent consumption by the drugs in question was also investigated. The corresponding rate law under the control of charge transfer was developed, and kinetic parameters were derived. In this context, the charge-transfer resistance accessible both theoretically and through impedancemetry was used as a criterion. The rate constants of the catalytic oxidation of the drugs and the electron-transfer coefficients are reported. A sensitive, simple, and time-saving amperometric procedure was developed for the analysis of deferasirox and deferiprone, with detection limits of 28 and 19 microM, respectively. The electrode was used for the direct assay of deferasirox and deferiprone tablets.     

An amperometric H2O2 biosensor based on cytochrome c immobilized onto nickel oxide nanoparticles/carboxylated multiwalled carbon nanotubes/polyaniline modified gold electrode

Cytochrome c was immobilized covalently onto nickel oxide nanoparticles/carboxylated multiwalled carbon nanotubes/polyaniline composite (NiO-NPs/cMWCNT/PANI) electrodeposited on gold (Au) electrode. An amperometric H₂O₂ biosensor was constructed by connecting this modified Au electrode along Ag/AgCl as reference and Pt wire as counter electrode to the galvanostat. The modified Au electrode was characterized by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and Fourier transform infra-red spectroscopy (FTIR). Cyclic voltammetric (CV) studies of the electrode at different stages demonstrated that the modified Au electrode had enhanced electrochemical oxidation of H₂O₂, which offered a number of attractive features to develop an amperometric biosensor based on split of H₂O₂. There was a good linear relationship between the current (mA) and H₂O₂ concentration in the range 3–700 μM. The sensor had a detection limit of 0.2 μM (S/N = 3) with a high sensitivity of 3.3 mA μM^?1 cm^?2. The sensor gave accurate and satisfactory results, when employed for determination of H₂O₂ in different fruit juices.     

Carbon nanotube/polyurethane modified hollow fiber‐pencil graphite electrode for in situ concentration and electrochemical quantification of anticancer drugs Capecitabine and Erlotinib

A sensitive electrochemical sensor has been designed for in situ preconcentration and determination of anticancer drugs Capecitabine (CPT) and Erlotinib hydrochloride (ETHC) based on a pencil graphite electrode modified with multivalued carbon nanotube—polyurethane (MWCNT‐PUFIX) nanocomposite that was supported with a piece of polypropylene hollow fiber (HF‐PGE). The electrochemical behavior of CPT and ETHC on the MWCNT‐PUFIX/HF‐PGE modified electrode was investigated by differential pulse voltammetry (DPV) techniques and the obtained results confirmed its efficiency for sensing of CPT and ETHC. The synthesized nanocomposite was characterized by infrared spectroscopy and scanning electron microscope. After optimization of some effective parameters on the method efficiency including pH, nanocomposite amount, the type of organic solvent, scan rate and the effect of some additives, the mentioned sensor presented suitable results for determination of CPT and ETHC with the linear ranges from 7.70 to 142.00 μM and 0.11 to 23.50 μM and detection limits of 0.11 and 0.02 μM, respectively. Also, the fabricated sensor has shown good performance in analysis of CPT and ETHC in biological samples.     

Nano nickel oxide modified non-enzymatic glucose sensors with enhanced sensitivity through an electrochemical process strategy at high potential

Development of fast and sensitive sensors for glucose determination is important in food industry, clinic diagnostics, biotechnology and many other areas. In these years, considerable attention has been paid to develop non-enzymatic electrodes to solve the disadvantages of the enzyme-modified electrodes, such as instability, high cost, complicated immobilization procedure and critical operating situation et al. Nano nickel oxide (NiO) modified non-enzymatic glucose sensors with enhanced sensitivity were investigated. Potential scanning nano NiO modified carbon paste electrodes up to high potential in alkaline solution greatly increases the amount of redox couple Ni(OH)(2)/NiOOH derived from NiO, and thus improves their electrochemical properties and electrocatalytical performance toward the oxidation of glucose. The non-enzymatic sensors response quickly to glucose and the response time is less than 5s, demonstrating excellent electrocatalytical activity and assay performance. The calibration plot is linear over the wide concentration range of 1-110 μM with a sensitivity of 43.9 nA/μM and a correlation coefficient of 0.998. The detection limit of the electrode was found to be 0.16 μM at a signal-to-noise ratio of 3. The proposed non-enzymatic sensors can be used for the assay of glucose in real sample.     

Electrochemical impedance immunosensor based on gold nanoparticles and aryl diazonium salt functionalized gold electrodes for the detection of antibody

Electrodes modified with passivating organic layers have been shown to, here and previously, to exhibit good Faradaic electrochemistry upon attachment of gold nanoparticles (AuNP). Due to their low background capacitances these constructs have good potential in electrochemical sensing. Herein is reported the application of these electrode constructs for impedance based immunosensing. The immunosensor was constructed by modifying a gold electrode with 4-thiophenol (4-TP) passivating layers by diazonium salt chemistry. Subsequently, the attachment of AuNP and then a biotin derivative as a model epitope to detect anti-biotin IgG were carried out. The interfacial properties of the modified electrodes were evaluated in the presence of Fe(CN)(6)(4-/3-) redox couple as a probe by cyclic voltammetry and electrochemical impedance spectroscopy. The impedance change, due to the specific immuno-interaction at the immunosensor surface was utilized to detect anti-biotin IgG. The increase in charge-transfer resistance (R(ct)) was linearly proportional to the concentration of anti-biotin IgG in the range of 5-500 ng mL(-1), with a detection limit of 5 ng mL(-1).     

羧基化石墨烯/半胱胺修饰金电极对多巴胺的电化学行为研究

为了基于羧基化石墨烯/半胱胺修饰金电极建立更为先进的多巴胺生物传感器，以定量检测儿茶酚胺类神经递质多巴胺，利用自组装技术将半胱胺修饰于金电极上，再利用1-乙基-\[3-二甲基氨基丙基\]碳酰二亚胺盐酸化物/N-羟基琥珀酰亚胺（EDC/NHS）交联剂将羧基化石墨烯固定在修饰后的金电极上制成多巴胺电化学传感器。先对修饰电极进行表征以检验其灵敏度，再利用循环伏安法研究该电极在多巴胺溶液中的电化学行为，包括检测条件的优化和传感器性能的测定。修饰电极表征结果表明，羧基化石墨烯/半胱胺修饰金电极提高了电极传递电子的能力，具有较高的灵敏度。经单因素实验得出，最佳检测条件为利用pH 6.00的0.30 mol·L-1磷酸盐缓冲溶液（PBS）配制多巴胺溶液，扫描速率设定为200 mV·s-1。在最佳检测条件下，制备的多巴胺电化学传感器电流的大小随着多巴胺浓度的增大而增大，在1.0×10-3~3.5×10-3 mol·L-1范围内呈现良好的线性关系，线性回归方程为I=8.120 6C+7.017，相关系数R2为0.999 5。且该传感器精密度好，稳定性强，具有一定的抗干扰能力。研究结果为药物盐酸多巴胺注射液中多巴胺含量测定提供了支撑。     

Controlled electrophoretic deposition of multifunctional nanomodules for bioelectrochemical applications

The design of an electrochemical glucose sensing device formed by the electrodeposition of multifunctional Au nanoparticles is reported here as a novel concept for an enhanced generic sensing platform. Initially gold nanoparticles (Au) were alternatively coated with a layer of positively charged redox polymer (ORP) and a negatively charged glucose oxidase (GOX) layer alternatively using layer-by-layer methodology to form multifunctional Au/ORP/GOX/ORP particles. The modification and stability of the Au nanoparticles was monitored by using UV-vis spectroscopy and zeta-potential measurements. The modified Au nanoparticles were electrophoretically deposited onto an electrode to produce an electrochemical glucose sensing device. A considerable influence of electrophoretic deposition time and potential was found on the sensing platform response. Preliminary responses to glucose addition showed an enhanced performance by applying an electrophoretic deposition potential of +1.2V vs. Ag/AgCl for 30min. The observed response in the case of microelectrode geometry was in the range of mAcm(2). This work also shows that the presence of a second outer ORP layer on the functionalised Au nanoparticles improved the response.     

Voltammetric detection of anti-HIV replication drug based on novel nanocomposite gold-nanoparticle–CaCO<Subscript>3</Subscript> hybrid material

A novel bionanocomposite, horse radish peroxidase- gold-nanoparticle–Calcium carbonate (HRP-AuNPs-CaCO₃), hybrid material was encapsulated by silica sol on a glassy carbon electrode (GCE). The fabricated modified electrode was used as a novel voltammetric sensor for electrochemical sensing of anti-HIV replication drug i.e. deferiprone. The surface morphology of the modified electrode was characterized by scanning electron microscopy (SEM). Results obtained from the voltammetric measurements show that HRP-AuNPs-CaCO₃ modified GCE offers a selective and sensitive electrochemical sensor for the determination of deferiprone. Under experimental conditions, the proposed voltammetric sensor has a linear response range from 0.01 to 10,000 μM with a detection limit of 0.01 μM. Furthermore, the fabricated sensor was successfully applied to determine deferiprone level in spiked urine and serum samples.     

A novel sensor based on electrochemical polymerization of diglycolic acid for determination of acetaminophen

Diglycolic acid (DA) polymer was coated on glassy carbon (GC) electrode by cyclic voltammetry (CV) technique for the first time. The electrochemical performances of the modified electrode were investigated by CV and electrochemical impedance (EIS). The obtained electrode showed an excellent electrocatalytic activity for the oxidation of acetaminophen (ACOP). A couple of well-defined reversible electrochemical redox peaks were observed on the ploy(DA)/GC electrode in ACOP solution. Compared with bare GC electrode, the oxidation peak potential of ACOP on ploy(DA)/GC electrode moved from 0.289 V to 0.220 V. Meanwhile, the oxidation peak current was much higher on the modified electrode than that on the bare GC electrode, indicating DA polymer modified electrode possessed excellent performance for the oxidation of ACOP. This kind of capability of the modified electrode can be enlisted for the highly sensitive and selective determination of ACOP. Under the optimized conditions, a wide linear range from 2 × 10(-8) to 5.0 × 10(-4)M with a correlation coefficient 0.9995 was obtained. The detection limit was 6.7 × 10(-9)M (at the ratio of signal to noise, S/N=3:1). The modified electrode also exhibited very good stability and reproducibility for the detection of ACOP. The established method was applied to the determination of ACOP in samples. An average recovery of 100.1% was achieved. These results indicated that this method was reliable for determining ACOP.     

Fabrication of an amperometric d-amino acid biosensor based on nickel hexacyanoferrate polypyrrole hybrid film deposited on glassy carbon electrode

A nickel hexacyanoferrate polypyrrole film was synthesized through an electrochemical two-step methodology leading to a very stable and homogenous robust hybrid film. A highly sensitive, specific and rapid amperometric d-amino acid biosensor was constructed by immobilizing d-amino acid oxidase on this film deposited over the surface of a glassy carbon electrode. The modified electrode was characterized by scanning electron microscopy, electrochemical impedance spectroscopy and Fourier transform infrared spectrophotometry. The biosensor showed optimum response within 1 s, when operated at 50 mV s^?1 in 0.01 M Tris HCl buffer, pH 7.0 at 30 °C. The biosensor exhibited excellent sensitivity with a detection limit of 1.5 µM (S/N = 3) for d-amino acids and wider linear range, 20–500 µM. Analytical recovery of added d-alanine (5 and 10 mM) in serum samples was 98.00 and 98.80 %, respectively. Within-batch and between-batch coefficients of variation in serum samples were 1.36 and 2.77 %, respectively. The enzyme electrode was used more than 50 times over 2 months, when stored at 4 °C. The proposed modified electrode exhibited sufficient mechanical and electrochemical stability and high sensitivity compared to earlier electrochemical d-amino acid biosensors. Interference by ascorbic acid and uric acid, the main interfering species in the biological samples, was negligible.     

Myoglobin immobilization on electrodeposited nanometer-scale nickel oxide particles and direct voltammetry

Prosperity of information on the reactions of redox-active sites in proteins can be attained by voltammetric studies in which the protein sample is located on a suitable surface. This work reports the presentation of myoglobin/nickel oxide nanoparticles/glassy carbon (Mb/NiO NPs/GC) electrode, ready by electrochemical deposition of the NiO NPs on glassy carbon electrode and myoglobin immobilization on their surfaces by the potential cycling method. Images of electrodeposited NiO NPs on the surface of glassy carbon electrode were obtained by scanning electron microscopy (SEM) and atomic force microscopy (AFM). A pair of well-defined redox peaks for Mb(Fe(III)-Fe(II)) was obtained at the prepared electrode by direct electron transfer between the protein and nanoparticles. Electrochemical parameters of immobilized myoglobin such as formal potential (E(0')), charge transfer coefficient (alpha) and apparent heterogeneous electron transfer rate constant (k(s)) were estimated by cyclic voltammetry and nonlinear regression analysis. Biocatalytic activity was exemplified at the prepared electrode for reduction of hydrogen peroxide.     

Disposable electrochemical detectors based on nickel nanowires for carbohydrate sensing

Nanowires (NWs) are critically important building blocks of nanotechnology for sensing, biosensing and bioelectronics. However, in order to avoid complex and stiff configurations reported, a simpler and disposable approach is needed. Nickel nanowires (NiNWs) are one of the most promising alternatives because they allow magnetic manipulations through the application of an external magnetic field and they remain to be exploited in analytical field for electrochemical biosensing in real samples. In this work, NiNWs were characterized by scanning electronic microscopy (SEM), transmission electronic microscopy (TEM), energy-dispersive X-ray spectrometry (EDS) and X-ray photoelectronic spectroscopy (XPS) and then easily used in the construction of disposable detectors on carbon-screen printed electrodes (CSPEs). Fabricated NiNWs using alumina templates were about 330 nm of diameter and 6 μm lengths. XPS revealed that NiNWs based electrodes contained just a 0.9% of Ni with an enhancement of current density of about 65 times in comparison with Ni-bulk electrode under flow conditions. Electrochemically activated NiNWs (at -1.5 V, 600 s under magnetic field of 2×4200 G) gave the best signal-to-noise performance exhibiting fast response time to representative carbohydrate, very good mechanical stability, no memory effect and an extreme resistance to fouling under hydrodynamics conditions allowing an excellent analytical performance on the board of just one disposable single-electrode (RSDs≤7%, n=50). Analytical performance of NiNWs was also excellent in the analysis of selected samples exhibiting very good reliability, precision (RSDs≤2%) and recovery rates (95-115%). NiNWs are becoming a simple and easy-to-use nanotool for fast, reliable and decentralized sensing of carbohydrates; and as a consequence, "disposable nanoanalytics" is approaching.