高效杀蚊苏云金芽孢杆菌BRC-LLP29的发酵优化

苏云金芽孢杆菌BRC-LLP29为新型高效杀蚊菌株,应用快速有效的数学统计方法对其杀蚊毒力的发酵培养进行优化.通过单因素筛选确定最佳碳源为葡萄糖、麦芽糖、可溶性淀粉,氮源为typetone、大豆蛋白胨、干酪素;最佳金属离子为Mg²⁺、Al³⁺.采用二水平Placlkett-Burman设计对影响毒力的8因素进行显著性筛选,获得培养基成分中3个重要影响因子:葡萄糖、干酪素和Al₂（SO₄）₃;运用爬坡路径法对这3种因子进行试验,获得3种重要因子的最适浓度范围;通过响应面分析法得到3个重要因子的交互作用和最佳条件,确定BRC-LLP29菌株最佳毒力水平的发酵培养基为:葡萄糖19.8g/L、干酪素28.4g/L、Al₂（SO₄）₃1.2g/L、MgSO₄ 2g/L、K₂HPO₄ 3g/L、CaCO₃ 0.5g/L,优化后毒力水平达到致死率61.11%,与响应面数学模型的预测值只有5.91%的误差.发酵条件优化结果表明:发酵温度为31°,发酵初始pH为7.0,摇瓶装量为40mL/250mL三角瓶,每瓶的接种量为3.5%,发酵72h,对致倦库蚊最终致死率达到最高为83.33%.     

酸性α-淀粉酶菌株的筛选及其发酵条件研究

自淀粉厂周边土壤分离筛选到一株高效耐酸α-淀粉酶菌株SH3,初步鉴定为酵母菌,发酵粗酶p H范围3.8-8.0,最适作用p H5.0,该酶在80℃下仍有酶活,最适作用温度50℃。经单因素发酵条件的研究与优化,最适温度37℃,培养基初始p H5.0,可溶性淀粉作碳源,蛋白胨为氮源,200 m L装液量。正交试验确定最佳产酶条件为可溶性淀粉15 g/L、蛋白胨30 g/L、37℃、p H4.5,该条件下酶活力为96.8 U/mg。     

L-精氨酸高产菌红曲霉的筛选及发酵初步研究

对不同样品中的真菌进行了L-精氨酸高产菌株的筛选,从红曲米中分离出1株高产L-精氨酸菌株红曲霉H13,其初始发酵液中L-精氨酸产量为1.67 g/L.通过单因素实验对其液体发酵进行研究.结果表明,最佳碳源是可溶性淀粉,最佳浓度为10％,最佳氮源是蛋白胨,最佳浓度为3％,最佳pH值4.5,温度30℃,种子培养时间为18 h,摇瓶装液量50 mL/250 mL.转速为120 r/min,发酵时间7d.在此条件下进行发酵培养,所得发酵液产L-精氨酸4.08 g/L,菌丝体干重为10.32 g/L,菌丝体中L-精氨酸含量为24.17 mg/g.     

玫瑰黄链霉菌NKZ-259发酵培养基的优化

玫瑰黄链霉菌NKZ-259是一株生防菌株,其次级代谢能产生植物生长调节类物质吲哚乙酸(IAA)。为了进一步提高菌株代谢产生IAA的含量,本试验对该菌株的发酵培养基进行了优化。利用单因子试验确定发酵培养基中最适的6种营养成分为葡萄糖、可溶性淀粉、蛋白胨、硝酸钾、磷酸氢二钾和L-色氨酸;通过Plackett-Burman设计筛选出影响菌株发酵产生IAA的主要因素为L-色氨酸、葡萄糖和磷酸氢二钾;采用中心组合试验(CCD)及响应面法分析各因素的交互作用。最终确定菌株代谢产生IAA的最优发酵培养基为:L-色氨酸2.24 g/L,葡萄糖20.7 g/L,磷酸氢二钾0.5 g/L,可溶性淀粉10 g/L,蛋白胨3 g/L,硝酸钾4.5g/L;使用优化后的发酵培养基菌株代谢产生IAA的含量为45.377 4μg/mL,比原始发酵培养基IAA的含量提高了3倍。     

内生解淀粉芽孢杆菌CC09产Iturin A摇瓶发酵条件优化

【目的】提高内生解淀粉芽孢杆菌CC09发酵产抗菌脂肽Iturin A的产量。【方法】首先采用单因子实验研究了碳源、氮源、NaCl浓度、pH、温度、转速和装液量等因子对CC09产Iturin A能力的影响,然后对其中显著性因子:氮源浓度、pH、温度及装液量4个因素进行正交实验,进一步优化发酵条件。【结果】优化培养基组成及发酵条件可以提高CC09菌株的生长速度及产Iturin A的量,其中可溶性淀粉以及一定比例的蛋白胨和酵母粉是CC09菌株产Iturin A的良好碳源和氮源;培养温度、装液量、培养液pH等也对CC09菌株产Iturin A有显著影响。优化后的培养基成分:可溶性淀粉(碳源)5 g/L、比例为3:1的胰蛋白胨酵母粉混合氮源15 g/L、NaCl 1 g/L;最佳培养条件:pH 6.0、28°C、摇床转速120 r/min、培养瓶装液量20%。【结论】在此条件下,Iturin A的产量可达到690 mg/L,较优化前的138 mg/L提高了4倍。     

高产大黄素赭曲霉的离子注入诱变选育及发酵特性分析

通过N+离子注入获得大黄素高产菌株Aspergillus ochraceus LP-0301并优化了发酵条件,使其最终产率达1.453 mg/L,比出发菌株提高2.96倍.优化后的培养基为:镁离子1.5 g/L,硝酸铵10 g/L,蛋白胨10 g/L,玉米淀粉75 g/L;优化后的发酵条件为:温度30 ℃,初始pH为7...     

高效表达淀粉酶Bacillus koreensis的培养基响应面优化

为降低烟叶中的淀粉含量,提高烟叶的可用性,从云南马龙C3F-2014烟叶表面筛选出一株高产淀粉酶的细菌,经16sRNA测序鉴定为 Bacillus koreensis 。本研究利用响应面法优化 Bacillus koreensis 的培养基提高了其表达淀粉酶的产量。首先,单因素优化试验表明培养基的最优碳源、氮源和金属离子分别为淀粉、蛋白胨和Ca2+,培养条件单因素试验表明 Bacillus koreensis 最适初始pH、最适温度和最适接种量分别为pH8.0、37 ℃和3%。利用Box-Behnken中心组合设计对可溶性淀粉、蛋白胨、Ca2+设计三因素三水平实验,通过响应面回归分析,得到模型预测的最优培养基条件。在18.74 g/L可溶性淀粉,21.56 g/L蛋白胨,0.52 g/L CaCl2的培养基条件下 Bacillus koreensis 产淀粉酶最高。验证试验得到的淀粉酶活力达到959.39±22.34 U/mL,与模型的预测值相近,比未优化前提高了69.76%。本研究结果为烟草天然源淀粉酶处理烟叶,提高烟叶品质的工业化应用提供了基础。     

淡色生赤壳菌(Bionectria ochroleuca)Bo-1菌株产生抗菌物质的发酵条件优化

以淡色生赤壳菌(Bionectria ochroleuca)Bo-1菌株发酵液乙酸乙酯粗提物对水稻白叶枯病菌(Xanthomonas oryzaepv.oryzae,Xoo)抑菌活性为检测指标,采用单因素试验优化Bo-1菌株产生抗菌物质培养所需的碳源、氮源、无机盐;通过正交试验优化培养基配方和摇瓶发酵条件。研究结果表明,Bo-1菌株产生抗菌物质适宜的碳源、氮源和无机盐分别为淀粉、蛋白胨、MgSO4·7H2O;优化的培养基配方为:淀粉30 g/L,蛋白胨2 g/L,MgSO4·7H2O 0.5 g/L;适宜的发酵条件为:温度30℃,转速150 r/min,装液量80 mL/250 mL,pH 6.5。     

ARTP诱变选育环孢菌素A高产菌株及发酵工艺优化

采用常压室温等离子体技术(Atmospheric Room Temperature Plasma,ARTP)对雪白白僵菌FIM-1809菌株进行诱变,得到一株遗传稳定性较高的突变高产菌FIM-1809-7,其产环孢菌素A能力较初始菌株提高约39%。通过单因素和正交设计试验优化,确定最佳发酵培养基组分及培养条件为：玉米浆粉6%、可溶性淀粉12%、葡萄糖1.2%、蛋白胨2%,pH 5.6,菌种菌龄为72 h,接种量10%,装液量70 m L/500 m L,发酵时间8 d,最终突变菌株产环孢菌素A效价较出发菌种增加了约53%。结果表明,采用ARTP技术结合发酵条件优化能够有效提高雪白白僵菌产环孢菌素A的能力,为该菌株的工业化应用奠定了良好的基础。     

响应面法优化革耳Panus rudis FG-35菌株产漆酶培养基

采用Plackett-Burman设计和响应面分析相结合的方法,对革耳Panus rudis FG-35菌株产漆酶的液体培养基配方进行优化。单因素试验结果显示,发酵培养基中的最优碳源为可溶性淀粉,最优氮源为蛋白胨;Plackett-Burman设计筛选出影响漆酶产量的3个重要因素为可溶性淀粉、金属Ca2+离子和吐温-40,在此基础上运用最陡爬坡试验逼近最大响应值区域,最后利用Box-Behnken试验设计及响应面分析法进行回归分析,获得最佳培养基配方为:可溶性淀粉10.040 4 g/L、蛋白胨0.2 g/L、K2HPO41.00g/L、ZnSO4·7H2O 0.008 g/L、MgSO4·7H2O 0.5 g/L、CuSO4·7H2O 0.007 g/L、FeSO4·7H2O 0.005 g/L、MnSO40.035 g/L、CaCl20.0816 g/L、VB10.1 g/L、吐温-40 0.428%。在优化后的条件下摇瓶发酵产漆酶酶活力为263.31 U/mL,与模型预测值接近,发酵产酶量比优化前提高1.07倍,同时优化后的发酵液对木质素降解进行试验发现,优化后漆酶对木质素降解率提高了14.34%。     

The fermentative production of acetone-butanol by Clostridium acetobutylicum.

Fourteen different media were used in the fermentative production of acetone-butanol. The highest total yields were achieved in medium I. Potato starch and soluble starch were suitable as carbon sources. The best concentrations of potato starch and soluble starch were 500.0 and 10.0 g/l, respectively. Peptone was the most favourable nitrogen source. The best concentration of peptone was 4.0 g/l. Calcium carbonate in 3.6 g/l acted as buffering agent in the fermentation process. The best initial pH value of the fermentation medium was 6.0. The optimum temperature was 32--33degreesC. The fermentation process required 120 h to obtain maximum yields of acetone-butanol.     

Direct production of L+-lactic acid from starch and food wastes using Lactobacillus manihotivorans LMG18011

This study describes several essential factors for direct and effective lactic acid production from food wastes by Lactobacillus manihotivorans LMG18011, and optimum conditions for simultaneous saccharification and fermentation using soluble starch and food wastes as substrates. The productivity was found to be affected by three factors: (1) initial pH, which influenced amylase production for saccharification of starch, (2) culture pH control which influenced selective production of L(+)-lactic acid, and (3) manganese concentration in medium which improved in production rate and yield of lactic acid. The optimum initial pH was 5.0-5.5, and the fermentation pH for the direct and effective fermentation from starchy substrate was 5.0 based on the yield of L(+)-lactic acid. Under these conditions, 19.5 g L(+)-lactic acid was produced from 200 g food wastes by L. manihotivorans LMG18011. Furthermore, the addition of manganese stimulated the direct fermentation significantly, and enabled complete bioconversion within 100 h.     

产γ-谷氨基甲酰胺合成酶菌株的筛选及产酶条件研究

以假单胞菌(Pseudomonas sp.)为出发菌株,通过紫外诱变筛选得到一株γ-谷氨基甲酰胺合成酶高产菌株UV-19,其酶活提高32.54%。以突变株UV-19为供试菌株,对γ-谷氨基甲酰胺合成酶的发酵条件进行优化。首先利用Plackett-Burman设计筛选出影响较大的4个因素:葡萄糖、蛋白胨、起始pH值、装液量。在此基础上再利用CCD响应面分析法进行优化,得到最佳产酶培养条件为(g/L):葡萄糖15、蛋白胨12、NaCl 5.0、MgSO4.7H2O 0.2、K2HPO4.3H2O 0.5、甲胺盐酸盐1.0g/L、起始pH值6.5、装液量72mL/250mL。该优化条件下进行产酶培养,假单胞菌发酵产γ-谷氨基甲酰胺合成酶酶活力可达32.68U/mL。     

手性拆分环氧氯丙烷菌株的筛选、鉴定及产酶条件研究

从土壤中筛选到5株环氧化物水解酶生产菌,并通过ITS序列鉴定了其中的C375菌,结果为黑曲霉（Aspergillus nigerZJB-09103）。考察了培养基不同碳源、氮源、金属离子和pH等对产酶的影响,得到了较佳的培养基条件：淀粉16g／L,豆饼粉3g／L,蛋白胨3g／L,KH2PO4 0．4g／L,K2HPO4 0．8g／L,MgSO4 0．2g／L,ZnSO4 0．03g／L,pH6．5。采用优化后的培养基条件,酶活力达到156．1U／L,比优化前初始发酵培养条件下的酶活提高了252％,当环氧化物水解酶催化时间为10h时,（s）-环氧氯丙烷的对映体过量值（e．e．）可达99．0％。产率为18．6％。     

Optimization of culture conditions for production of the anti-tubercular alkaloid hirsutellone A by Trichoderma gelatinosum BCC 7579

AIMS: This work aimed to optimize the culture conditions for production of a novel and potent anti-tubercular alkaloid, hirsutellone A, by the saprophytic soil fungus Trichoderma gelatinosum BCC 7579. METHODS AND RESULTS: The fungus was initially cultured in shake flasks at 25 degrees C in the potato dextrose broth (PDB) supplemented with various carbon and nitrogen sources and mineral salts to select suitable medium for mycelial growth and hirsutellone A production. Cultivation conditions were further optimized by adjusting initial pH and changing temperature levels to maximize the production of hirsutellone A. The optimal condition that increased the production of hirsutellone A from 19.04 mg l(-1), obtained from basal condition, to 610.55 mg l(-1) and reduced the cultivation time from 40 to 6 days was to cultivate in a shaker at 200 rev min(-1) at 25 degrees C in PDB plus 20 g l(-1) soluble starch, 10 g l(-1) peptone and 2.5% (v/v) salt solution with initial pH of 7. Production of hirsutellone A in larger-scale using a 5-l batch fermenter was also completed yielding 958 mg l(-1) of hirsutellone A within 6 days. CONCLUSIONS: The suitable culture conditions for hirsutellone A production by T. gelatinosum BCC 7579 was the cultivation in 5-l fermenter at 25 degrees C in PDB plus 20 g l(-1) soluble starch, 10 g l(-1) peptone and 2.5% (v/v) salt solution with an initial pH of 7. SIGNIFICANCE AND IMPACT OF THE STUDY: The production of hirsutellone A in a fermenter to obtain a high yield and reduce an incubation period will become very useful in anti-tubercular drug development process in the future.     

蔗渣发酵菌剂培养基的筛选及发酵条件的优化

采用单因素和正交试验研究了蔗渣高效发酵菌剂(芽孢杆菌B-A、曲霉菌F-A、链霉菌A-B)的摇瓶发酵最佳工艺条件.结果表明:芽孢杆菌B-A的最佳培养基配方:牛肉膏0.3%、蛋白胨1%、葡萄糖1%、NaCl 0.5%、可溶性淀粉0.5%、3.08%浓度的MnSO4溶液0.1;最适发酵条件为pH7、装液量100 ml(250 ml三角瓶)、36℃培养27 h.曲霉F-A的最佳培养基配方:葡萄糖3%、豆饼粉3%、蛋白胨1.2%、酵母膏0.3%、K2HPO4 0.05%、KH2PO40.05%、CaCl20.08%、MgSO40.04%、MnSO40.04%、ZnSO40.02%;最适发酵条件为pH6、装液量50 ml、30℃培养3 d.链霉菌A-B的最佳培养基配方:可溶性淀粉4.5%、蔗糖1%、豆饼粉3%、NaNO30.2%、ZnSO40.01%、KH2PO40.001%;最适发酵条件为pH7、装液量50 ml、30℃培养3 d.     

生物转化法合成16α-羟基泼尼松龙的发酵工艺研究

目的:研究1株玫瑰产色链霉菌(Streptomyces roseochromogenes)的发酵培养基和底物转化条件,以提高16α-羟基泼尼松龙的转化率。方法:采用紫外与氯化锂复合诱变获得目的菌株TS-58,利用正交实验等方法考查摇瓶发酵条件,研究不同浓度的碳源、氮源对玫瑰产色链霉菌生长的影响,以及不同底物浓度、底物加入时间、装液量、金属离子和添加助溶剂等条件对转化生成16α-羟基泼尼松龙能力的影响。结果:获得最佳转化培养基为葡萄糖10 g/L、可溶性淀粉50 g/L、蛋白胨10 g/L、黄豆饼粉25 g/L、磷酸二氢钾0.2 g/L、硫酸镁0.5 g/L硫酸锌0.5 g/L。在底物投料量5 mg/mL添加0.8 mg/ml PEG助溶剂的最优条件下,16α-羟基泼尼松龙的转化率达到了13.8%。结论:突变株Streptomyces roseochromogenes TS-58能有效地在泼尼松龙上引入16α-羟基羟基,为工业生产16α-羟基泼尼松龙奠定了基础。