Adsorption of peptide nucleic acid and DNA decamers at electrically charged surfaces.

Adsorption behavior of peptide nucleic acid (PNA) and DNA decamers (GTAGATCACT and the complementary sequence) on a mercury surface was studied by means of AC impedance measurements at a hanging mercury drop electrode. The nucleic acid was first attached to the electrode by adsorption from a 5-microliter drop of PNA (or DNA) solution, and the electrode with the adsorbed nucleic acid layer was then washed and immersed in the blank background electrolyte where the differential capacity C of the electrode double layer was measured as a function of the applied potential E. It was found that the adsorption behavior of the PNA with an electrically neutral backbone differs greatly from that of the DNA (with a negatively charged backbone), whereas the DNA-PNA hybrid shows intermediate behavior. At higher surface coverage PNA molecules associate at the surface, and the minimum value of C is shifted to negative potentials because of intermolecular interactions of PNA at the surface. Prolonged exposure of PNA to highly negative potentials does not result in PNA desorption, whereas almost all of the DNA is removed from the surface at these potentials. Adsorption of PNA decreases with increasing NaCl concentration in the range from 0 to 50 mM NaCl, in contrast to DNA, the adsorption of which increases under the same conditions.     

Adsorption behavior of globular proteins at the water/mercury interface.

The adsorption of globular proteins at solid/liquid or liquid/liquid interfaces provides evidence of unfolded molecular conformation. Proteins with high apolar character are strongly unfolded, while those with high polar character are generally incompletely unfolded. Structural changes of globular proteins at adsorption on mercury electrodes were studied by ac polarography and capacity–time curves. The surface area per molecule of nine globular proteins was determined from the adsorption kinetics at the dropping mercury electrode. For all the proteins investigated, this value was greater than the maximal molecular cross section of the native proteins. The surface area was about 19 Ų per amino acid residue, which coincides with the value for unfolded proteins at the water/air interface. Differences between dropping mercury electrode and hanging drop mercury electrode occurred only with lysozyme and phosphorylase; for the other proteins, the structure of the adsorption layer was independent of the time of interaction at the electrode. Since not all of the reducible groups of the adsorbed proteins come into contact with the electrode, the flattening should be incomplete.     

Interaction of nucleic acids with electrically charged surfaces. VII. The effect of ionic strength of neutral medium on the conformation of dna adsorbed on the mercury electrode

Triangular-wave direct current (d.c.) voltammetry at a hanging mercury drop electrode and phase-selective alternating current (a.c.) polarography at a dropping mercury electrode were used for the investigation of adsorption of double-helical (ds) DNA at mercury electrode surfaces from neutral solutions of 0.05-0.4 M HCOONH4. It was found for the potential region T (from -0.1 V up to ca. -1.0 V) that the height of voltammetric peaks of ds DNA is markedly influenced by the initial potential only at relatively low ionic strength (mu) (from 0.05 up to ca. 0.3). Also a decrease of differential capacity (measured by means of a.c. polarography) in the region T depended markedly on the electrode potential only at relatively low ionic strength. The following conclusions were made concerning the interaction of ds DNA with a mercury electrode charged to potentials of the region T in neutral medium of relatively low ionic strength mu < 0.3). (i) When ds DNA is adsorbed, a significantly higher number of DNA segments is anchored in the positively charged electrode surface than in the surface bearing a negative charge, (ii) In the region T, especially adsorbed labile regions of ds DNA are opened in the electrode surface, which are present in ds DNA already in the bulk of the solution, (iii) In the narrow region of potentials in the Vicinity of the zero charge potential a higher number of ds DNA segments can be opened, probably as a consequence of the strain which could act on the ds DNA molecule in the course of the segmental adsorption/desorption process.     

Voltammetric investigation on interaction of protein with chromotrope 2R and its analytical application

The electrochemical behaviors of the interaction of chromotrope 2R (CH2R) with human serum albumin (HSA) are investigated on the hanging mercury drop electrode with linear sweep voltammetry. In the acidic buffer solution (pH 2.5) CH2R has a well-defined voltammetric reductive wave at −0.34 V (SCE). On the addition of HSA into the CH2R solution, the reductive peak current of CH2R decreases with little movement of the peak potential. The voltammetric study shows that the electrochemical parameters of interaction solution do not change and a new electrochemically non-active complex is formed via interaction of CH2R with HSA, which cannot be reduced on the Hg electrode and results in the decrease of the free concentration of CH2R. The decrease of reductive peak current is proportional to HSA concentration and further used for protein detection. The binding ratio and the binding constant are further calculated with the experimental voltammetric data.     

Interactions of surface-confined DNA with electroreduced mitomycin C comparison with acid-activated mitomycin C

The anticancer activity of the antineoplastic drug mitomycin C (MC) was investigated using transfer stripping cyclic voltammetry (TSCV) with single-stranded DNA-modified hanging mercury drop electrode (HMDE). Reductive activation of MC is necessary for drug covalent binding to DNA, and we have found that some potential-controlled interactions of MC with DNA occur at the electrode, i.e. MC can be activated by electroreduction. Acid and electroreductive MC activations were compared and different adducts were subsequently generated, suggesting that the drug can bind to DNA in more than one way. Under conditions of acid activated MC, a monofunctional adduct between C-1 of MC and N-7 of guanine was formed on the electrode surface, reduced at - 0.44 V (vs. SCE). However, when the DNA-modified electrode was immersed in a MC solution and potentials corresponding to the quinone moiety reduction (- 0.3 V or more negative vs. SCE) were applied, an intrastrand bifunctional adduct between C-1 and C-10 of MC and two N-7 of a pair of adjacent guanines in ssDNA were formed at the electrode, reduced at - 0.49 V, i.e. 50 mV more negative than the monoadduct. The results presented in this paper show for the first time electrochemical detection of DNA-MC adducts at the hanging mercury drop electrode.     

Interaction of nucleic acids with electrically charged surfaces: II. Conformational changes in double-helical polynucleotides

The influence of adsorption of double-stranded (ds) DNA, ds RNA and homopolymeric pairs at a mercury electrode on conformation of these polynucleotides was studied. Changes in the polarographic reducibility of polynucleotides, which were followed by means of normal pulse polarography and linear sweep peak voltammetry at the dropping mercury electrode were exploited to indicate conformational changes. It was found that, as a consequence of adsorption of ds polynucleotides on the negatively charged electrode conformational changes similar to denaturation take place in a narrow potential region around ?1.2 V (the region U). After sufficiently long time of the contact with the electrode (under our conditions about 10 s) these changes reach limiting values, which can approach total denaturation. Upon adsorption of ds polynucleotides on the electrode charged to more positive potentials than the region U either (1) no conformational changes occur or (2) only a small part of the polynucleotide (probably labile regions of the ds molecule) is very quickly denatured - the remainder of the molecule preserves its ds structure. Conformational changes of adsorbed ds polynucleotides are influenced by factors which change the stability of ds polynucleotides in solution. It is supposed that denaturation of ds polynucleotides in the region U might result from the strains connected with the repulsion of certain segments of the molecule anchored on the electrode from the negatively charged surface.     

Effect of the cathode potential and sulfate ions on nitrate reduction in a microbial electrochemical denitrification system

Recently, bioelectrochemical systems have been demonstrated as advantageous for denitrification. Here, we investigated the nitrate reduction rate and bacterial community on cathodes at different cathode potentials [?300, ?500, ?700, and ?900 mV vs. standard hydrogen electrode (SHE)] in a two-chamber microbial electrochemical denitrification system and effects of sulfate, a common nitrate co-contaminant, on denitrification efficiency. The results indicated that the highest nitrate reduction rates (3.5 mg L^?1 days^?1) were obtained at a cathode potential of ?700 mV, regardless of sulfate presence, while a lower rate was observed at a more negative cathode potential (?900 mV). Notably, although sulfate ions generally inhibited nitrate reduction, this effect was absent at a cathode potential of ?700 mV. Polymerase chain reaction–denaturing gradient gel electrophoresis revealed that bacterial communities on the graphite-felt cathode were significantly affected by the cathode potential change and sulfate presence. Shinella-like and Alicycliphilus-like bacterial species were exclusively observed on cathodes in reactors without sulfate. Ochrobactrum-like and Sinorhizobium-like bacterial species, which persisted at different cathode potentials irrespective of sulfate presence, were shown to contribute to bioelectrochemical denitrification. This study suggested that a cathode potential of around ?700 mV versus SHE would ensure optimal nitrate reduction rate and counteract inhibitory effects of sulfate. Additionally, sulfate presence considerably affects denitrification efficiency and microbial community of microbial electrochemical denitrification systems.     

Imprinted polymer-modified hanging mercury drop electrode for differential pulse cathodic stripping voltammetric analysis of creatine

The molecularly imprinted polymer [poly(p-aminobenzoicacid-co-1,2-dichloroethane)] film casting was made on the surface of a hanging mercury drop electrode by drop-coating method for the selective and sensitive evaluation of creatine in water, blood serum and pharmaceutical samples. The molecular recognition of creatine by the imprinted polymer was found to be specific via non-covalent (electrostatic) imprinting. The creatine binding could easily be detected by differential pulse, cathodic stripping voltammetric signal at optimised operational conditions: accumulation potential −0.01 V (versus Ag/AgCl), polymer deposition time 15 s, template accumulation time 60 s, pH 7.1 (supporting electrolyte ≤ 5 × 10⁻⁴ M NaOH), scan rate 10 mV s⁻¹, pulse amplitude 25 mV. The modified sensor in the present study was found to be highly reproducible and selective with detection limit 0.11 ng mL⁻¹ of creatine. Cross-reactivity studies revealed no response to the addition of urea, creatinine and phenylalanine; however, some insignificant magnitude of current was observed for tryptophan and histidine in the test samples.     

Anodic concentration loss and impedance characteristics in rotating disk electrode microbial fuel cells

A rotating disk electrode (RDE) was used to investigate the concentration loss and impedance characteristics of anodic biofilms in microbial fuel cells (MFCs). Amperometric time–current analysis revealed that at the rotation rate of 480 rpm, a maximum current density of 168 µA cm^?2 can be achieved, which was 22.2 % higher than when there was no rotation. Linear sweep voltammetry and electrochemical impedance spectroscopy tests showed that when the anodic potential was set to ?300 mV vs. Ag/AgCl reference, the power densities could increase by 59.0  %, reaching 1385 mW m^?2, the anodic resistance could reduce by 19  %, and the anodic capacitance could increase by 36 %. These results concur with a more than 85 % decrease of the diffusion layer thickness. Data indicated that concentration loss, diffusion layer thickness, and the mixing velocity play important roles in anodic resistance reduction and power output of MFCs. These findings could be helpful to the design of future industrial-scale MFCs with mixed bacteria biofilms.     

Adsorption of single-stranded and double-helical polynucleotides on the mercury electrode

The adsorption of single-stranded polynucleotides and double-helical DNA on the dropping mercury electrode has been studied with the aid of Breyer's alternating current (a.c.) polarography. Our results indicate that all three constituents of polynucleotides (residues of bases, sugar, and phosphoric acid) are involved in the adsorption. At neutral pH their participation in adsorption depends on the ionic strength, the potential of the electrode, and the conformation of the polynucleotide in the solution. At an ionic strength of about 0.1, double-helical DNA is adsorbed electrostatically on a positively charged electrode surface by inadequately masked negative charges of the phosphate groups. At a higher ionic srength (about 0.5), this electrostatic adsorption is no longer detectable by using a.c. polarography; under these conditions it is probable that native DNA is adsorbed around the potential of the electrocapillary maximum with the aid of sugar residues and a few bases. Single-stranded polynucleotides, on the other hand, are primarily adsorbed by means of the bases. Desorption of double-helical DNA occurs around a potential of ?1.2 V against SCE. At this potential, the helical regions of single-stranded polynucleotides are also desorbed. Desorption of the disordered regions of single-stranded polynucleotides occurs at more negative potentials. Adsorption and desorption of a small number of bases released from double-helical DNA was evident in the a.c. polarograms only at elevated temperature, or at room temperature after degradation of DNA by sonication.     

Effect of redox potential regulation on succinic acid production by Actinobacillus succinogenes

The effects of redox potential used as a control parameter on the process of succinic acid production in batch cultures of Actinobacillus succinogenes NJ113 have been investigated. In batch fermentation, cell growth and metabolite distribution were changed with redox potential levels in the range of ?100 to ?450 mV. From the results, the ORP level of ?350 mV was preferable, which resulted in high succinic acid yield (1.28 mol mol^?1), high succinic acid productivity (1.18 g L^?1 h^?1) and high mole ratio of succinic acid to acetic acid (2.02). The mechanism of redox potential regulation was discussed by metabolic flux analysis and the ratio of NADH/NAD⁺. We expected that redox potential can be used as a valuable parameter to monitor and control much more anaerobic fermentation production.     

Über die Adsorption von DNS in der Grenzfläche Quecksilber–Elektrolyt

The adsorption of deoxyribonucleic acid (DNA) in the mercury–electrolyte interface has been investigated. The effect of this adsorption on the differential capacity of the electrical double layer between a polarized mercury surface and an 0.15M NaCl solution containing DNA was measured by means of the alternating current polarography (Breyer polarography). The effective alternating current ? under actual conditions (adsorption processes only, small electrolytic resistance, small alternating current frequency, and alternating current amplitude) is directly proportional to the differential double layer capacity. The combination of this method with the application of a stationary mercury drop electrode allows the coverage of the electrode to be followed, continuously in the range 0.2 sec, to about 60 sec. The diffusion is the rate-controlled step of the adsorption kinetics. Therefore the lowering of the alternating current ? by the adsorbed DNA is proportional to the surface concentration for partly covered surface and reaches a constant value after the surface becomes fully covered. Adsorption of further layers does not affect the differential capacity. This makes it possible to determine the maximum surface concentration of the DNA. For that it is necessary to determine the diffusion coefficient of DNA. This was done directly by Strassburger and Reinert in our institute. The surface concentrations of the native DNA and the relative surface concentrations of the denatured DNA in dependence on the potential of the polarized mercury surface was estimated. Both surface concentrations show a pronounced dependence on the potential with a minimum of the surface concentration around ?0.4 V with respect to the normal calomel electrode. This property may be caused by the structure of the adsorption layer depending on the potential. That means that only several segments at the rigid DNA molecules are adsorbed and the other ones remain in the solution near the surface. The adsorption in the neighborhood of the electrocapillary zero potential at ?0.4 V is strongest, and therefore the fraction of the adsorbed segments has a maximum. At these potentials consequently the maximum coverage is already reached at relatively low surface concentrations. Opposite to this is Miller's hypothesis, that native DNA preserves its double helical structure when adsorbed on a negatively charged mercury surface, whereas unfolding occurs on a positively charged mercury surface. Miller's hypothesis is supported by facts that the surface concentration of the denatured DNA should be independent of the potential and should be equal to the surface concentration of the native DNA at a positively charged mercury surface. But an evaluation of Miller's diagrams by no means gives an independence on the potential of the surface concentration of the denatured DNA and no accordance between the surface concentrations of denatured and of native DNA's at the positively charged mercury surface. Moreover Miller compared different DNA samples with different moleculer weights and possibly with different molecular weight distributions. Both the molecular weight and the molecular weight distribution have a pronounced influence on the surface concentration. Therefore this accordance mentioned above is not evident. The critical inspection of Miller's work and the own investigation lead to the conclusion that an unfolding or denaturation of native DNA does not take place in the mercury–electrolyte interface.     

Electrochemical selective detection of dopamine on microbial carbohydrate-doped multiwall carbon nanotube-modified electrodes

Microbial carbohydrate-doped multiwall carbon nanotube (MWNT)-modified electrodes were prepared for the purpose of determining if 4-(2-aminoethyl)benzene-1,2-diol (3,4-dihydroxyphenylalanine; dopamine) exists in the presence of 0.5 mM ascorbic acid, a representative interfering agent in neurotransmitter detection. The microbial carbohydrate dopants were α-cyclosophorohexadecaose (α-C16) from Xanthomonas oryzae and cyclic-(1 → 2)-β-d-glucan (Cys) from Rhizobium meliloti. The cyclic voltammetric responses showed that the highest sensitivity (5.8 × 10^?3 mA cm^?2 μM^?1) is attained with the Cys-doped MWNT-modified ultra-trace carbon electrode, and that the α-C16-doped MWNT-modified glassy carbon electrode displays the best selectivity to dopamine (the approximate peak potential separation is 310 mV).     

Adsorptive transfer stripping voltammetry: Determination of nanogram quantities of DNA immobilized at the electrode surface

In adsorptive transfer stripping voltammetry (AdTSV), DNA is first adsorbed at the electrode, the electrode is washed and transferred (with the adsorbed layer) in the medium not containing DNA, and voltammetric analysis is performed in this medium. Adsorption can be performed from a drop of DNA solution, which makes it possible to reduce the volume of the analyzed sample by two orders of magnitude as compared to that of conventional voltammetry. With the hanging mercury drop electrode the limit of detection of single-stranded DNA is below 0.1 micrograms/ml; thus if the adsorption is performed from a 10-microliter drop of DNA solution subnanogram quantities of single-stranded DNA are sufficient for the analysis. In AdTSV the behavior of single- and double-stranded DNAs markedly differ from each other in a manner similar to that in the conventional voltammetric or polarographic analysis; AdTSV can thus be used in DNA structure analysis. In AdTSV the DNA transport and its adsorption at the electrode are separated from the electrode process; due to this fact it is possible (a) to perform the voltammetric analysis of DNA from media not suitable for voltammetric analysis of the conventional type, (b) to study the interaction of immobilized DNA with other substances in solution without the results of the voltammetric analysis being influenced by DNA interactions in the bulk of solution, and (c) to exploit the differences of adsorbability of DNA and other substances in order to separate them on the electrode.     

Micropropagation and in vitro production of secondary metabolites of Croton floribundus Spreng.

Croton floribundus Spreng., a native plant from South America, was utilized for in vitro micropropagation and phytochemical analyses. The effects of the addition of naphthaleneacetic acid and indole butyric acid, on the production of shoots and leaves, as well as volatile constituent production, were determined. The combination of naphthaleneacetic acid and indole butyric acid at a ratio of 1:1 led to the production of the maximum number of leaves and longest shoots after a 60-d subculture period. Analyses of leaf dichloromethane extracts using gas chromatography–mass spectrometry showed that monoterpenes and sesquiterpenes were the main chemical classes present in both in vivo and in vitro conditions. Use of these plant growth regulators in the medium-induced quantitative changes in the major monoterpenes (neral, geranial, limonene, and carvone). In vitro leaf extracts produced compounds such as carvone as well as a large amount of trans-β-farnesene, with the highest production of carvone (16.8%) being produced on medium supplemented with 1.0 mg?L^?1 naphthaleneacetic acid. These results suggested the occurrence of biotransformation reactions of limonene and farnesyl cations in culture.     

Synthesis and electrochemistry of anthraquinone-oligodeoxynucleotide conjugates

Electroactive oligodeoxynucleotides (ODNs) with specific base sequences have a potential application as electrical sensors for DNA molecules. To this end, a phosphoramidite that bears a 9, 10-anthraquinone (AQ) group tethered to the 2'-O of the uridine via a hexylamino linker, 2'-O-[6-[2-oxo(9, 10-anthraquinon-2-yl)amino]hexyl]-5'-O-(4,4'-dimethoxytrityl)uridi ne 3'-[2-(cyanoethyl)bis(1-methylethyl)phosphoramidite] (3), has been synthesized and used to prepare three ODNs with tethered AQs using standard phosphoramidite chemistry. The synthetic methodology thus allows the synthesis of ODNs with electroactive tags attached to given locations in the base sequence. Cyclic voltammetric behavior of these AQ-ODN conjugates was examined in aqueous buffer solutions at a hanging mercury drop electrode. At slow sweep rates, nearly reversible two-electron waves characteristic of an adsorbed anthraquinone/hydroquinone redox couple was observed for all of the AQ-ODN conjugates. Approximate Langmuirian isotherms were found for the AQ-ODNs with molecular footprints, calculated from the saturation coverages, that scaled with molecular size. The cyclic voltammetric response of the duplexes formed from the AQ-ODNs and their complementary ODN was complicated by the competitive adsorption of the individual ODNs and possibly the duplex species as well.     

Square-wave adsorptive voltammetry of dexamethasone: redox mechanism, kinetic properties, and electroanalytical determinations in multicomponent formulations

The electrochemical reduction behavior of dexamethasone at a hanging mercury drop electrode was investigated by cyclic and square-wave adsorptive voltammetries in a Britton–Robinson buffer at pH 2.0. The optimized experimental conditions consisted of a pulse potential frequency of 100 s⁻¹, a pulse amplitude of 15 mV, and a potential step height of 2 mV, with E_acc = −0.60 V and t_acc = 15 s. From these parameters, it was also possible to develop a detailed study about the kinetic and mechanistic events involved in the reduction process. Two well-defined peaks were observed in the cathodic scan, and peak 2 was used to obtain analytical curves. A linear range between 4.98 × 10⁻⁸ and 6.10 × 10⁻⁷ mol L⁻¹, with a detection limit of 2.54 × 10⁻⁹ mol L⁻¹ and a quantification limit of 8.47 × 10⁻⁹ mol L⁻¹, was observed. Moreover, it was possible to achieve a simple, selective, and versatile methodology adaptable to the quantification of dexamethasone because common excipients used in multicomponent commercial formulations caused no interference. The satisfactory recoveries and the low relative standard deviation data reflected the high accuracy and precision of the proposed method for the determination of dexamethasone in injectable eye drops and elixir samples.     

Inhibition of veratridine-induced delayed inactivation of the voltage-sensitive sodium channel by synthetic analogs of crambescin B

Crambescin B carboxylic acid, a synthetic analog of crambescin B, was recently found to inhibit the voltage-sensitive sodium channels (VSSC) in a cell-based assay using neuroblastoma Neuro 2A cells. In the present study, whole-cell patch-clamp recordings were conducted with three heterologously expressed VSSC subtypes, Na_v1.2, Na_v1.6 and Na_v1.7, in a human embryonic kidney cell line HEK293T to further characterize the inhibition of VSSC by crambescin B carboxylic acid. Contrary to the previous observation, crambescin B carboxylic acid did not inhibit peak current evoked by depolarization from the holding potential of ?100 mV to the test potential of ?10 mV in the absence or presence of veratridine (VTD). In the presence of VTD, however, crambescin B carboxylic acid diminished VTD-induced sustained and tail currents through the three VSSC subtypes in a dose-dependent manner, whereas TTX inhibited both the peak current and the VTD-induced sustained and tail currents through all subtypes of VSSC tested. We thus concluded that crambescin B carboxylic acid does not block VSSC in a similar manner to TTX but modulate the action of VTD, thereby causing an apparent block of VSSC in the cell-based assay.     

Cyclic voltammetry of DNA at a mercury electrode: an anodic peak specific for guanine

Synthetic homopolyribonucleotides poly(A), poly(U), poly(C), and poly(G), poly(A, G, U), apurinic acid and native and denatured DNA from calf thymus were analyzed by means of cyclic voltammetry (CV) using a hanging mercury drop electrode. It was shown that guanine containing polynucleotides, i.e. poly(G), poly(A, G, U) and DNA yield an anodic peak of guanine in the vicinity of a potential of -0.3 V (against a saturated calomel electrode). The guanine peak appeared only at a sufficiently negative switching potential (about -2 V). The appearance of the guanine peak was conditioned by a reduction of guanine residues in the region of the switching potential and reoxidation of the reduction product in the vicinity of -0.3 V. Native and thermally denatured DNAs were investigated under the conditions of both complete and incomplete coverage of the electrode in various background electrolytes. Both DNA forms yielded anodic CV peaks of guanine with the peak of denatured DNA being always higher than that of native DNA. Irradiation of native DNA with relatively small doses of gamma radiation (5-120 Gy) resulted in an increase of the anodic peak. A comparison of changes induced by gamma radiation in the anodic (guanine) and cathodic (reduction of adenine and cytosine) peaks showed a steeper increase of the cathodic peak as compared to that of the anodic one. It has been concluded that in the given dose range the DNA double-helical structure is mainly damaged in the adenine-thymine rich regions.     

Influence of salicylic acid and methyl jasmonate elicitation on anthocyanin production in callus cultures of Rosa hybrida L.

This study was undertaken to investigate the effects of salicylic acid (SA) and methyl jasmonate (MeJA) on anthocyanin induction, biomass accumulation, and color value (CV) indices for both pigment content (PC) and pigment production (PP) in callus cultures of Rosa hybrida cv. Pusa Ajay. A concentration-dependent response was exhibited by cultures on SA and MeJA at different concentrations individually or in combinations to Euphorbia millii medium supplemented with 204.5 mM sucrose, 2.45 μM indole butyric acid and 2.33 μM kinetin. There was positive influence on both callus biomass and anthocyanin accumulation. Treatment with 0.5 μM MeJA was most effective in inducing anthocyanin biosynthesis in callus cultures. Anthocyanin accumulation in callus cultures was enhanced with the addition of SA and MeJA, but these did not differ significantly from control for the number of days required for pigment initiation and for color intensification. Moreover, the addition of 0.5 μM MeJA alone resulted in a higher frequency of color response (97.25 %), PC (3.48 ± 0.07 CV g^?1 FW), and PP (1.56 ± 0.03 CV test tube^?1) over control. In contrast, the presence of higher levels of SA (400 μM) and MeJA (5.0 μM) reduced frequency of color response, as well as levels of PC and PP. MeJA did not increase biomass accumulation but promoted frequency of color response, PC and PP. Hence, it was suggested that 0.5 μM MeJA promoted anthocyanin production in rose callus cultures. Significant correlation was found between frequency of response and each of the PC (r = 0.988) and PP (r = 0.990). Furthermore, PC and PP were also highly correlated (r = 0.998).