Optimal design of flax fiber reinforced polymer composite as a lightweight component for automobiles from a life cycle assessment perspective

The present study combines the generalized rule‐of‐mixture (ROM) model and the Ashby material selection method for the life cycle assessment (LCA) of flax fiber reinforced polymers (FRPs) and glass FRPs (GFRPs). The ROM model allows life cycle environmental impact predictions according to specific parameters of flax FRPs such as fiber format, volume fraction, manufacturing technique, and load‐bearing capacity. The comparisons applied in this study are constructed on two common composite structures: mat panels and injection molded struts with equal stiffness and strength as the design criteria. On the one hand, the parametric LCA predicts that the equal strength design criterion for flax FRPs contributes to consistent mass increases, subsequently resulting in higher life cycle environmental impacts compared to the reference GFRPs; on the other hand, under the equal stiffness criterion the flax mat polypropylene (flax mat‐PP) film helps with mass reduction in reference to the glass mat‐PP composite, leading to the 20–50% life cycle environmental impact reductions for most impact categories. The subsequent evaluation of the influences of the fiber volume fraction on flax FRPs shows different patterns. For the short flax fiber‐PP composite, a steady decrease of the life cycle CO₂ emissions can be observed with the increasing fiber volume fraction. However, for the flax mat‐PP composite, depending on the tensile modulus of the flax fiber, the optimal volume fractions of the fiber change from 28 to 32% v/v, whereby the lowest life cycle greenhouse gas (GHG) emissions can be achieved.     

Regional variations in life cycle greenhouse gas emissions of canola‐derived jet fuel produced in western Canada

This study investigates the life cycle GHG emissions of jet fuel produced via the hydroprocessed esters and fatty acids (HEFA) pathway from canola grown in western Canada, with a focus on characterizing regional influences on emissions. We examine the effects of geographic variations in soil type, agricultural inputs, farming practices, and direct land use changes on life cycle GHG emissions. We utilize GREET 2016 but replace default feedstock production inputs with geographically representative data for canola production across eight western Canadian regions (representing 99% of Canada's canola production) and replace the default conversion process with data from a novel process model previously developed in ASPEN in our research group wherein oil extraction is integrated with the HEFA‐based fuel production process. Although canola production inputs and yields vary across the regions, resulting life cycle GHG emissions are similar if effects of land use and land management changes (LMC) are not included; 44–48 g CO₂e/MJ for the eight regions (45%–50% reduction compared to petroleum jet fuel). Results are considerably more variable, 16–58 g CO₂e/MJ, when including effects of land use and LMC directly related to conversion of lands from other uses to canola production (34%–82% reduction compared to petroleum jet fuel). We establish the main sources of emissions in the life cycle of canola jet fuel (N‐fertilizer and related emissions, fuel production), identify that substantially higher emissions may occur when using feedstock sourced from regions where conversion of forested land to cropland had occurred, and identify benefits of less intense tillage practices and increased use of summerfallow land. The methods and findings are relevant in jurisdictions internationally that are incorporating GHG emissions reductions from aviation fuels in a low carbon fuel market or legislating carbon intensity reduction requirements.     

Fuel Economy and Greenhouse Gas Emissions Labeling for Plug‐In Hybrid Vehicles from a Life Cycle Perspective

Fuel economy has been an effective indicator of vehicle greenhouse gas (GHG) emissions for conventional gasoline‐powered vehicles due to the strong relationship between fuel economy and vehicle life cycle emissions. However, fuel economy is not as accurate an indicator of vehicle GHG emissions for plug‐in hybrid (PHEVs) and pure battery electric vehicles (EVs). Current vehicle labeling efforts by the U.S. Environmental Protection Agency (EPA) and Department of Transportation have been focused on providing energy and environmental information to consumers based on U.S. national average data. This article explores the effects of variations in regional grids and regional daily vehicle miles traveled (VMT) on the total vehicle life cycle energy and GHG emissions of electrified vehicles and compare these results with information reported on the label and on the EPA's fuel economy Web site. The model results suggest that only 25% of the life cycle emissions from a representative PHEV are reflected on current vehicle labeling. The results show great variation in total vehicle life cycle emissions due to regional grid differences, including an approximately 100 gram per mile life cycle GHG emissions difference between the lowest and highest electric grid regions and up to a 100% difference between the state‐specific emission values within the same electric grid regions. Unexpectedly, for two regional grids the life cycle GHG emissions were higher in electric mode than in gasoline mode. We recommend that labels include stronger language on their deficiencies and provide ranges for GHG emissions from vehicle charging in regional electricity grids to better inform consumers.     

Environmental assessment of urban mobility: Combining life cycle assessment with land-use and transport interaction modelling—Application to Lyon (France)

In France, greenhouse gas (GHG) emissions from transport have grown steadily since 1950 and transport is now the main source of emissions. Despite technological improvements, urban sprawl increases the environmental stress due to car use. This study evaluates urban mobility through assessments of the transport system and travel habits, by applying life cycle assessment methods to the results of mobility simulations that were produced by a Land Use and Transport Interactions (LUTI) model. The environmental impacts of four life cycle phases of urban mobility in the Lyon area (exhausts, fuel processing, infrastructure and vehicle life cycle) were estimated through nine indicators (global warming potential, particulate matter emissions, photochemical oxidant emissions, terrestrial acidification, fossil resource depletion, metal depletion, non-renewable energy use, renewable energy use and land occupancy). GHG emissions were estimated to be 3.02 kg CO₂-eq inhabitant⁻¹ day⁻¹, strongly linked to car use, and indirect impacts represented 21% of GHG emissions, which is consistent with previous studies. Combining life cycle assessment (LCA) with a LUTI model allows changes in the vehicle mix and fuel sources combined with demographic shifts to be assessed, and provides environmental perspectives for transport policy makers and urban planners. It can also provide detailed analysis, by allowing levels of emissions that are generated by different categories of households to be differentiated, according to their revenue and location. Public policies can then focus more accurately on the emitters and be assessed from both an environmental and social point of view.     

Life cycle assessment of energy and GHG emissions during ethanol production from grass straws using various pretreatment processes

Purpose  

The aim of this study was to perform a well-to-pump life cycle assessment (LCA) to investigate the overall net energy balance and environmental impact of bioethanol production using Tall Fescue grass straw as feedstock. The energy requirements and greenhouse gas (GHG) emissions were compared to those of gasoline to explore the potential of bioethanol as sustainable fuel.     

Impact of Updated Material Production Data in the GREET Life Cycle Model

The Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) model developed by Argonne National Laboratory quantifies the life cycle energy consumption and air emissions resulting from the production and use of light‐duty vehicles in the United States. GREET is comprised of two components: GREET 1 represents the fuel cycle of various energy carriers, including automotive fuels, and GREET 2 represents the vehicle cycle, which accounts for the production of vehicles and their constituent materials. The GREET model was updated in 2012 and now includes higher‐resolution material processing and transformation data. This study evaluated how model updates influence material and vehicle life cycle results. First, new primary energy demand and greenhouse gas (GHG) emissions results from GREET 2 for steel, aluminum, and plastics resins are compared herein with those from the previous version of the model as well as industrial results. A part of the comparison is a discussion about causes of differences between results. Included in this discussion is an assessment of the impact of the new material production data on vehicle life cycle results for conventional internal combustion engine (ICE) vehicles by comparing the energy and GHG emission values in the updated and previous versions of GREET 2. Finally, results from a sensitivity analysis are presented for identifying life cycle parameters that most affect vehicle life cycle estimates.     

Life cycle analysis of biochemical cellulosic ethanol under multiple scenarios

Cellulosic ethanol is widely believed to offer substantial environmental advantages over petroleum fuels and grain‐based ethanol, particularly in reducing greenhouse gas emissions from transportation. The environmental impacts of biofuels are largely caused by precombustion activities, feedstock production and conversion facility operations. Life cycle analysis (LCA) is required to understand these impacts. This article describes a field‐to‐blending terminal LCA of cellulosic ethanol produced by biochemical conversion (hydrolysis and fermentation) using corn stover or switchgrass as feedstock. This LCA develops unique models for most elements of the biofuel production process and assigns environmental impact to different phases of production. More than 30 scenarios are evaluated, reflecting a range of feedstock, technology and scale options for near‐term and future facilities. Cellulosic ethanol, as modeled here, has the potential to significantly reduce greenhouse gas (GHG) emissions compared to petroleum‐based liquid transportation fuels, though substantial uncertainty exists. Most of the conservative scenarios estimate GHG emissions of approximately 45–60 g carbon dioxide equivalent per MJ of delivered fuel (g CO₂e MJ^?1) without credit for coproducts, and 20–30 g CO₂e MJ^?1 when coproducts are considered. Under most scenarios, feedstock production, grinding and transport dominate the total GHG footprint. The most optimistic scenarios include sequestration of carbon in soil and have GHG emissions below zero g CO₂e MJ^?1, while the most pessimistic have life‐cycle GHG emissions higher than petroleum gasoline. Soil carbon changes are the greatest source of uncertainty, dominating all other sources of GHG emissions at the upper bound of their uncertainty. Many LCAs of biofuels are narrowly constrained to GHG emissions and energy; however, these narrow assessments may miss important environmental impacts. To ensure a more holistic assessment of environmental performance, a complete life cycle inventory, with over 1100 tracked material and energy flows for each scenario is provided in the online supplementary material for this article.     

Life Cycle Greenhouse Gas Emissions Reduction From Rigid Thermal Insulation Use in Buildings

Thermal insulation is a strategic product for reducing energy consumption and related greenhouse gas (GHG) emissions from the building sector. This study examines from a life cycle perspective the changes in GHG emissions resulting from the use of two rigid thermal insulation products manufactured and installed from 1971 to 2025. GHG emissions related to insulation production and fugitive releases of blowing agents are modeled and compared with GHG savings from reduced heating loads in North America, Europe, and Asia. Implementation of alternative blowing agents has greatly improved the carbon dioxide 100‐year equivalent (CO₂‐eq) emission performance of thermal insulation. The net average CO₂‐eq savings to emissions ratio for current extruded polystyrene (XPS) and polyisocyanurate (PIR) insulation studied was 48:1, with a broad range from 3 to 1,800. Older insulation products manufactured with chlorofluorocarbons (CFCs) can result in net cumulative GHG emissions. Reduction of CO₂‐eq emissions from buildings is governed by complex interactions between insulation thickness and placement, climate, fuel type, and heating system efficiencies. A series of charts mapping both emissions payback and net savings demonstrate the interactions between these factors and provide a basis for specific policy recommendations to guide effective insulation investments and placement.     

Economic Assessment of Greenhouse Gas Emissions Reduction by Vehicle Lightweighting Using Aluminum and High‐Strength Steel

The life cycle greenhouse gas (GHG) reduction benefits of vehicle lightweighting (LW) were evaluated in a companion article. This article provides an economic assessment of vehicle LW with aluminum and high‐strength steel. Relevant cost information taken from the literature is synthesized, compiled, and formed into estimates of GHG reduction costs through LW. GHG emissions associated with vehicle LW scenarios between 6% and 23% are analyzed alongside vehicle life cycle costs to achieve these LW levels. We use this information to estimate the cost to remove GHG emissions per metric ton by LW, and we further calculate the difference between added manufacturing cost and fuel cost savings from LW. The results show greater GHG savings derived from greater LW and added manufacturing costs as expected. The associated production costs are, however, disproportionately higher than the fuel cost savings associated with higher LW options. A sensitivity analysis of different vehicle classes confirms that vehicle LW is more cost‐effective for larger vehicles. Also, the cost of GHG emissions reductions through lightweighting is compared with alternative GHG emissions reduction technologies for passenger vehicles, such as diesel, hybrid, and plug‐in hybrid electric powertrains. The results find intensive LW to be a competitive and complementary approach relative to the technological alternatives within the automotive industry but more costly than GHG mitigation strategies available to other industries.     

Life cycle assessment of eucalyptus short rotation coppices for bioenergy production in southern France

Short rotation coppices (SRC) are considered prime candidates for biomass production, yielding good‐quality feedstock that is easy to harvest. Besides technical, social and economical aspects, environmental issues are important to be taken into account when developing SRC. Here, we evaluated the environmental impacts of delivering 1 GJ of heat from eucalyptus SRC using life cycle assessment (LCA), based on management scenarios involving different rotations lengths, fertilizer input rates, stem densities and harvest methods. Compared to equivalent fossil chains, all eucalyptus scenarios achieved savings of fossil energy and greenhouse gas (GHG) emissions in the 80–90% range, and had generally lower impacts, except for eutrophication. The 3 year rotation scenario was the most energy and GHG‐intensive, whereas manual felling for the longer rotations resulted in twofold larger photochemical ozone impacts compared to the other scenarios. Transportation of wood chips and fertilization were the top two contributors to the impacts, the latter being more important with the shorter rotation lengths due to the evergreen character of eucalyptus. The possibility of including ecosystem carbon dynamics was also investigated, by translating the temporary sequestration of atmospheric CO₂ in the above and belowground biomass of eucalyptus as CO₂ savings using various published equivalence factors. This offset the life cycle GHG emissions of heat provision from eucalyptus SRC by 70–400%.     

玉米秸秆基纤维素乙醇生命周期能耗与温室气体排放分析

生命周期评价是目前分析产品或工艺的环境负荷唯一标准化工具,利用其生命周期分析方法可以有效地研究纤维素乙醇生命周期能耗与温室气体排放问题。为了定量解释以玉米秸秆为原料的纤维素乙醇的节能和温室气体减排潜力,利用生命周期分析方法对以稀酸预处理、酶水解法生产的玉米秸秆基乙醇进行了生命周期能耗与温室气体排放分析,以汽车行驶1 km为功能单位。结果表明：与汽油相比,纤维素乙醇E100 (100％乙醇) 和E10 (乙醇和汽油体积比=1∶9) 生命周期化石能耗分别减少79.63％和6.25％,温室气体排放分别减少53.98％和6.69％;生物质阶段化石能耗占到总化石能耗68.3％,其中氮肥和柴油的生命周期能耗贡献最大,分别占到生物质阶段的45.78％和33.26％;工厂电力生产过程的生命周期温室气体排放最多,占净温室气体排放量的42.06％,提升技术减少排放是降低净排放的有效措施。     

Wood pellets,what else? Greenhouse gas parity times of European electricity from wood pellets produced in the south‐eastern United States using different softwood feedstocks

Several EU countries import wood pellets from the south‐eastern United States. The imported wood pellets are (co‐)fired in power plants with the aim of reducing overall greenhouse gas (GHG) emissions from electricity and meeting EU renewable energy targets. To assess whether GHG emissions are reduced and on what timescale, we construct the GHG balance of wood‐pellet electricity. This GHG balance consists of supply chain and combustion GHG emissions, carbon sequestration during biomass growth and avoided GHG emissions through replacing fossil electricity. We investigate wood pellets from four softwood feedstock types: small roundwood, commercial thinnings, harvest residues and mill residues. Per feedstock, the GHG balance of wood‐pellet electricity is compared against those of alternative scenarios. Alternative scenarios are combinations of alternative fates of the feedstock materials, such as in‐forest decomposition, or the production of paper or wood panels like oriented strand board (OSB). Alternative scenario composition depends on feedstock type and local demand for this feedstock. Results indicate that the GHG balance of wood‐pellet electricity equals that of alternative scenarios within 0–21 years (the GHG parity time), after which wood‐pellet electricity has sustained climate benefits. Parity times increase by a maximum of 12 years when varying key variables (emissions associated with paper and panels, soil carbon increase via feedstock decomposition, wood‐pellet electricity supply chain emissions) within maximum plausible ranges. Using commercial thinnings, harvest residues or mill residues as feedstock leads to the shortest GHG parity times (0–6 years) and fastest GHG benefits from wood‐pellet electricity. We find shorter GHG parity times than previous studies, for we use a novel approach that differentiates feedstocks and considers alternative scenarios based on (combinations of) alternative feedstock fates, rather than on alternative land uses. This novel approach is relevant for bioenergy derived from low‐value feedstocks.     

Life Cycle–based Assessment of Energy Use and Greenhouse Gas Emissions in Almond Production,Part I: Analytical Framework and Baseline Results

This first article of a two‐article series describes a framework and life cycle–based model for typical almond orchard production systems for California, where more than 80% of commercial almonds on the world market are produced. The comprehensive, multiyear, life cycle–based model includes orchard establishment and removal; field operations and inputs; emissions from orchard soils; and transport and utilization of co‐products. These processes are analyzed to yield a life cycle inventory of energy use, greenhouse gas (GHG) emissions, criteria air pollutants, and direct water use from field to factory gate. Results show that 1 kilogram (kg) of raw almonds and associated co‐products of hulls, shells, and woody biomass require 35 megajoules (MJ) of energy and result in 1.6 kg carbon dioxide equivalent (CO₂‐eq) of GHG emissions. Nitrogen fertilizer and irrigation water are the dominant causes of both energy use and GHG emissions. Co‐product credits play an important role in estimating the life cycle environmental impacts attributable to almonds alone; using displacement methods results in net energy and emissions of 29 MJ and 0.9 kg CO₂‐eq/kg. The largest sources of credits are from orchard biomass and shells used in electricity generation, which are modeled as displacing average California electricity. Using economic allocation methods produces significantly different results; 1 kg of almonds is responsible for 33 MJ of energy and 1.5 kg CO₂‐eq emissions. Uncertainty analysis of important parameters and assumptions, as well as temporary carbon storage in orchard trees and soils, are explored in the second article of this two‐part article series.     

Mass balance and life cycle assessment of biodiesel from microalgae incorporated with nutrient recycling options and technology uncertainties

This article presents mass balances and a detailed life cycle assessment (LCA) for energy and greenhouse gases (GHGs) of a simulated microalgae biodiesel production system. Key parameters of the system include biomass productivity of 16 and 25 g m^?2 day^?1 and lipid content of algae of 40% and 25% for low and normal nitrogen conditions respectively. Based on an oil extraction efficiency from wet biomass of 73.6% and methane yields from anaerobically digested lipid‐extracted biomass of 0.31 to 0.34 l per gram of volatile solids, the mass balance shows that recycling growth media and recovering nutrients from residual biomass through anaerobic digestion can reduce the total demand for nitrogen by 66% and phosphorus by 90%. Freshwater requirements can be reduced by 89% by recirculating growth media, and carbon requirements reduced by 40% by recycling CO₂ from biogas combustion, for normal nitrogen conditions. A variety of technology options for each step of the production process and allocation methods for coproducts used outside the production system are evaluated using LCA. Extensive sensitivity and scenario analysis is also performed to provide better understanding of uncertainty associated with results. The best performing scenario consists of normal nitrogen cultivation conditions, bioflocculation and dissolved air flotation for harvesting, centrifugation for dewatering, wet extraction with hexane, transesterification for biodiesel production, and anaerobic digestion of biomass residual, which generates biogas used in a combined heat and power unit for energy recovery. This combination of technologies and operating conditions results in life cycle energy requirements and GHG emissions of 1.02 MJ and 71 g CO₂‐equivalent per MJ of biodiesel, with cultivation and oil extraction dominating energy use and emissions. Thus, even under optimistic conditions, the near‐term performance of this biofuel pathway does not achieve the significant reductions in life cycle GHG emissions hoped for from second‐generation biofuel feedstocks.     

Land management change greatly impacts biofuels’ greenhouse gas emissions

Harvesting corn stover for biofuel production may decrease soil organic carbon (SOC) and increase greenhouse gas (GHG) emissions. Adding additional organic matter into soil or reducing tillage intensity, however, could potentially offset this SOC loss. Here, using SOC and life cycle analysis (LCA) models, we evaluated the impacts of land management change (LMC), that is, stover removal, organic matter addition, and tillage on spatially explicit SOC level and biofuels’ overall life cycle GHG emissions in US corn–soybean production systems. Results indicate that under conventional tillage (CT), 30% stover removal (dry weight) may reduce baseline SOC by 0.04 t C ha^?1 yr^?1 over a 30‐year simulation period. Growing a cover crop during the fallow season or applying manure, on the other hand, could add to SOC and further reduce biofuels’ life cycle GHG emissions. With 30% stover removal in a CT system, cover crop and manure application can increase SOC at the national level by about 0.06 and 0.02 t C ha^?1 yr^?1, respectively, compared to baseline cases without such measures. With contributions from this SOC increase, the life cycle GHG emissions for stover ethanol are more than 80% lower than those of gasoline, exceeding the US Renewable Fuel Standard mandate of 60% emissions reduction in cellulosic biofuels. Reducing tillage intensity while removing stover could also limit SOC loss or lead to SOC gain, which would lower stover ethanol life cycle GHG emissions to near or under the mandated 60% reduction. Without these organic matter inputs or reduced tillage intensity, however, the emissions will not meet this mandate. More efforts are still required to further identify key practical LMCs, improve SOC modeling, and accounting for LMCs in biofuel LCAs that incorporate stover removal.     

Contribution of Urban Water Supply to Greenhouse Gas Emissions in China

Greenhouse gas (GHG) emissions from energy use in the water sector in China have not received the same attention as emissions from other sectors, but interest in this area is growing. This study uses 2011 data to investigate GHG emissions from electricity use for urban water supply in China. The objective is to measure the climate cobenefit of water conservation, compare China with other areas on a number of emissions indicators, and assist in development of policy that promotes low‐emission water supply. Per capita and per unit GHG emissions for water supplied to urban areas in China in 2011 were 24.5 kilograms carbon dioxide equivalent (kg CO₂‐eq) per capita per year and 0.213 kg CO₂‐eq per cubic meter, respectively. Comparison of provinces within China revealed that GHG emissions for urban water supply as a percentage of total province‐wide emissions from electricity use correlate directly with the rate of leakage and water loss within the water distribution system. This highlights controlling leakage as a possible means of reducing the contribution of urban water supply to GHG emissions. An inverse correlation was established between GHG emissions per unit water and average per capita daily water use, which implies that water demand tends to be higher when per unit emissions are lower. China's high emission factor for electricity generation inflates emissions for urban water supply. Shifting from emissions‐intensive electricity sources is crucial to reducing emissions in the water supply sector.     

Including albedo in time‐dependent LCA of bioenergy

Albedo change during feedstock production can substantially alter the life cycle climate impact of bioenergy. Life cycle assessment (LCA) studies have compared the effects of albedo and greenhouse gases (GHGs) based on global warming potential (GWP). However, using GWP leads to unequal weighting of climate forcers that act on different timescales. In this study, albedo was included in the time‐dependent LCA, which accounts for the timing of emissions and their impacts. We employed field‐measured albedo and life cycle emissions data along with time‐dependent models of radiative transfer, biogenic carbon fluxes and nitrous oxide emissions from soil. Climate impacts were expressed as global mean surface temperature change over time (?T) and as GWP. The bioenergy system analysed was heat and power production from short‐rotation willow grown on former fallow land in Sweden. We found a net cooling effect in terms of ?T per hectare (?3.8 × 10^–11 K in year 100) and GWP₁₀₀ per MJ fuel (?12.2 g CO₂e), as a result of soil carbon sequestration via high inputs of carbon from willow roots and litter. Albedo was higher under willow than fallow, contributing to the cooling effect and accounting for 34% of GWP₁₀₀, 36% of ?T in year 50 and 6% of ?T in year 100. Albedo dominated the short‐term temperature response (10–20 years) but became, in relative terms, less important over time, owing to accumulation of soil carbon under sustained production and the longer perturbation lifetime of GHGs. The timing of impacts was explicit with ?T, which improves the relevance of LCA results to climate targets. Our method can be used to quantify the first‐order radiative effect of albedo change on the global climate and relate it to the climate impact of GHG emissions in LCA of bioenergy, alternative energy sources or land uses.     

Influence of spatially dependent,modeled soil carbon emission factors on life‐cycle greenhouse gas emissions of corn and cellulosic ethanol

Converting land to biofuel feedstock production incurs changes in soil organic carbon (SOC) that can influence biofuel life‐cycle greenhouse gas (GHG) emissions. Estimates of these land use change (LUC) and life‐cycle GHG emissions affect biofuels' attractiveness and eligibility under a number of renewable fuel policies in the USA and abroad. Modeling was used to refine the spatial resolution and depth extent of domestic estimates of SOC change for land (cropland, cropland pasture, grassland, and forest) conversion scenarios to biofuel crops (corn, corn stover, switchgrass, Miscanthus, poplar, and willow) at the county level in the USA. Results show that in most regions, conversions from cropland and cropland pasture to biofuel crops led to neutral or small levels of SOC sequestration, while conversion of grassland and forest generally caused net SOC loss. SOC change results were incorporated into the Greenhouse Gases, Regulated Emissions, and Energy use in Transportation (GREET) model to assess their influence on life‐cycle GHG emissions of corn and cellulosic ethanol. Total LUC GHG emissions (g CO₂eq MJ^?1) were 2.1–9.3 for corn‐, ?0.7 for corn stover‐, ?3.4 to 12.9 for switchgrass‐, and ?20.1 to ?6.2 for Miscanthus ethanol; these varied with SOC modeling assumptions applied. Extending the soil depth from 30 to 100 cm affected spatially explicit SOC change and overall LUC GHG emissions; however, the influence on LUC GHG emission estimates was less significant in corn and corn stover than cellulosic feedstocks. Total life‐cycle GHG emissions (g CO₂eq MJ^?1, 100 cm) were estimated to be 59–66 for corn ethanol, 14 for stover ethanol, 18–26 for switchgrass ethanol, and ?7 to ?0.6 for Miscanthus ethanol. The LUC GHG emissions associated with poplar‐ and willow‐derived ethanol may be higher than that for switchgrass ethanol due to lower biomass yield.     

Life Cycle Assessment of Novel Aircraft Interior Panels Made from Renewable or Recyclable Polymers with Natural Fiber Reinforcements and Non‐Halogenated Flame Retardants

A comprehensive life cycle assessment of panels for aircraft interiors was conducted, including both a conventional glass fiber‐reinforced panel and different novel sustainable panels. The conventional panel is made of a glass fiber‐reinforced thermoset composite with halogenated flame retardant, whereas the sustainable panels are made of renewable or recyclable polymers, natural fiber reinforcements, and nonhalogenated flame retardants. Four different sustainable panels were investigated: a geopolymer‐based panel; a linseed‐oil–based biopolymer panel; and two thermoplastic panels, one with polypropylene (PP) and another with polylactic acid (PLA). All of the sustainable panels were developed to fulfil fire resistance requirements and to be lighter than the conventional panels in order to reduce fuel consumption and air pollutant emissions from the aircraft. The environmental impacts associated with energy consumption and air emissions were assessed, as well as other environmental impacts resulting from the extraction and processing of materials, transportation of materials and waste, panel manufacturing, use, maintenance, and end of life (EoL). All the sustainable panels showed better environmental performance than the conventional panel. The overall impacts of the sustainable panels were offset by the environmental benefits in the use stage attributed to weight reduction. One square meter of the novel panels could save to 6,000 kilograms of carbon dioxide equivalents. The break‐even point (in months) at which the use of sustainable panels would yield an environmental benefit relative to the impacts arising in production and EoL was as follows: 1.2 for the geopolymer panel; 1.7 for the biopolymer panel; 10.4 for the PLA panel; and 54.5 for the PP panel.     

Range and uncertainties in estimating delays in greenhouse gas mitigation potential of forest bioenergy sourced from Canadian forests

Accurately assessing the delay before the substitution of fossil fuel by forest bioenergy starts having a net beneficial impact on atmospheric CO₂ is becoming important as the cost of delaying GHG emission reductions is increasingly being recognized. We documented the time to carbon (C) parity of forest bioenergy sourced from different feedstocks (harvest residues, salvaged trees, and green trees), typical of forest biomass production in Canada, used to replace three fossil fuel types (coal, oil, and natural gas) in heating or power generation. The time to C parity is defined as the time needed for the newly established bioenergy system to reach the cumulative C emissions of a fossil fuel, counterfactual system. Furthermore, we estimated an uncertainty period derived from the difference in C parity time between predefined best‐ and worst‐case scenarios, in which parameter values related to the supply chain and forest dynamics varied. The results indicate short‐to‐long ranking of C parity times for residues < salvaged trees < green trees and for substituting the less energy‐dense fossil fuels (coal < oil < natural gas). A sensitivity analysis indicated that silviculture and enhanced conversion efficiency, when occurring only in the bioenergy system, help reduce time to C parity. The uncertainty around the estimate of C parity time is generally small and inconsequential in the case of harvest residues but is generally large for the other feedstocks, indicating that meeting specific C parity time using feedstock other than residues is possible, but would require very specific conditions. Overall, the use of single parity time values to evaluate the performance of a particular feedstock in mitigating GHG emissions should be questioned given the importance of uncertainty as an inherent component of any bioenergy project.