共查询到20条相似文献，搜索用时 0 毫秒
1.
Low-cost sensors provide a unique opportunity to continuously monitor patient progress during rehabilitation; however, these sensors have yet to demonstrate the fidelity and lack the calibration paradigms necessary to be viable tools for clinical research. The purpose of this study was to validate a low-cost wearable sensor that accurately measured peak knee extension during clinical exercises and needed no additional equipment for calibration. Sagittal plane knee motion was quantified using a 9-axis motion sensor and directly compared to motion capture data. The motion sensor measured the field strength of a strong earth magnet secured to the distal femur, which was correlated with knee angle during a simple calibration process. Peak knee motions and kinematic patterns were compared with motion capture data using paired t-tests and cross correlation, respectively. Peak extension values during seated knee extensions were accurate within 5 degrees across all subjects (root mean square error: 2.6 degrees, P = 0.29). Knee flexion during gait strongly correlated (0.84 ≤ rxy ≤ 0.99) with motion capture measurements but demonstrated peak flexion errors of 10 degrees. In this study, we present a low-cost sensor (≈$ 35 US) that accurately determines knee extension angle following a calibration procedure that did not require any other equipment. Our findings demonstrate that this sensor paradigm is a feasible tool to monitor patient progress throughout physical therapy. However, dynamic motions that are associated with soft-tissue artifact may limit the accuracy of this type of wearable sensor. 相似文献
2.
The deadlift is a compound full-body exercise that is fundamental in resistance training, rehabilitation programs and powerlifting competitions. Accurate quantification of deadlift biomechanics is important to reduce the risk of injury and ensure training and rehabilitation goals are achieved. This study sought to develop and evaluate deadlift exercise technique classification systems utilising Inertial Measurement Units (IMUs), recording at 51.2 Hz, worn on the lumbar spine, both thighs and both shanks. It also sought to compare classification quality when these IMUs are worn in combination and in isolation. Two datasets of IMU deadlift data were collected. Eighty participants first completed deadlifts with acceptable technique and 5 distinct, deliberately induced deviations from acceptable form. Fifty-five members of this group also completed a fatiguing protocol (3-Repition Maximum test) to enable the collection of natural deadlift deviations. For both datasets, universal and personalised random-forests classifiers were developed and evaluated. Personalised classifiers outperformed universal classifiers in accuracy, sensitivity and specificity in the binary classification of acceptable or aberrant technique and in the multi-label classification of specific deadlift deviations. Whilst recent research has favoured universal classifiers due to the reduced overhead in setting them up for new system users, this work demonstrates that such techniques may not be appropriate for classifying deadlift technique due to the poor accuracy achieved. However, personalised classifiers perform very well in assessing deadlift technique, even when using data derived from a single lumbar-worn IMU to detect specific naturally occurring technique mistakes. 相似文献
3.
Wearable technology can be used to quantify running biomechanical patterns in a runner’s natural environment, however, changes in external factors during outdoor running may influence a runner’s typical gait pattern. Therefore, the purpose of this study was to determine how many runs are needed to define a stable or typical running pattern. Six biomechanical variables were recorded using a single wearable sensor placed on the lower back during ten outdoor runs for twelve runners. Univariate and multivariate distributions were created and based on the probability density function, the percent of similar data points (within 95%) from each unique run for the same runner were determined. Stability was defined when the addition of data from a new run resulted in less than a 5% change in the probability density function. To cross-validate, the percent of similar data points at stability was compared between the same and different runners using a repeated-measures MANOVA (Bonferroni-corrected α = 0.007). The maximum number of runs needed to reach stability for univariate and multivariate analyses was four and five, respectively. There was a significant overall effect on similar data points between the same and different runners (p = 0.001), with a greater percent of similar data points for the same runner compared to other runners (p < 0.007). Based on biomechanical data collected using a single wearable sensor placed on the lower back, this is the first study to show that four (univariate) to five (multivariate) runs are needed to establish a stable running pattern in real-world settings. 相似文献
4.
《IRBM》2020,41(2):80-87
ObjectivesThe number of elderly people is growing rapidly and aging is found to affect activities of daily living. Older adults are found to perform less physical activity when compared to younger ones. In the perspective of movement behavior, it is not well understood how are elderly different from younger ones. It is not known whether they produce only low frequency movement accelerations or the overall number of movements produced are reduced in elderly. It is also not known how elderly and younger ones perform movement transitions throughout the duration of a day and during night-time sleep.Material and methodsIn this study, 10 healthy young and 10 healthy old participants wore inertial measurement unit at their lower back for 3-days. The 24 hours of day were divided into four 6 hour time zones and transitions made by young and elderly were investigated. All participants performed their regular daily activities unhindered and longitudinal multi-day signals for acceleration and angular velocity were analyzed. Time-frequency analysis was performed using wavelet transform and frequency content of each movement performed was computed.ResultsWe found that both young and older adults performed significantly more low amplitude movements than medium and high amplitude movements. Healthy young adults produced significantly more movements at 1.1 Hz than older adults. Healthy young adults were also found to have produced significantly smaller number of transitions in the mid-phases of sleep. They were also found to produce significantly larger accelerations during night-time sleep transitions than their older counterparts.ConclusionThe advantages of collecting longitudinal data about human movement and sleep transition data can lead us to important clinical diagnosis. The information from longitudinal assessment can help develop lifestyle interventions for disease prevention, monitoring of chronic diseases to prevent or slow disease progression among elderly people. 相似文献
5.
Direct measurement of hand forces during assessment of manual materials handling is infeasible in most field studies and some laboratory studies (e.g., during patient handling). Therefore, this study proposed and evaluated the performance of a novel hand force estimation method based on ground reaction forces (GRFs) and body segment accelerations. 相似文献
6.
To predict shoulder strength, most current ergonomics software assume independence of the strengths about each of the orthopedic axes. Using this independent axis approach (IAA), the shoulder can be predicted to have strengths as high as the resultant of the maximum moment about any two or three axes. We propose that shoulder strength is not independent between axes, and propose an approach that calculates the weighted average (WAA) between the strengths of the axes involved in the demand.Fifteen female participants performed maximum isometric shoulder exertions with their right arm placed in a rigid adjustable brace affixed to a tri-axial load cell. Maximum exertions were performed in 24 directions, including four primary directions, horizontal flexion-extension, abduction-adduction, and at 15° increments in between those axes. Moments were computed and comparisons made between the experimentally collected strengths and those predicted by the IAA and WAA methods.The IAA over-predicted strength in 14 of 20 non-primary exertions directions, while the WAA underpredicted strength in only 2 of these directions. Therefore, it is not valid to assume that shoulder axes are independent when predicting shoulder strengths between two orthopedic axes, and the WAA is an improvement over current methods for the posture tested. 相似文献
7.
Gert S. Faber Idsart Kingma Sjoerd M. Bruijn Jaap H. van Dieën 《Journal of biomechanics》2009,42(14):2406-2409
Trunk inclination (TI) is used often to quantify back loading in ergonomic workplace evaluation. The aim of the present study was to determine whether TI can be obtained using a single inertial sensor (IS) on the back, and to determine the optimal IS location on the back for the estimation of TI. Gold standard TI, the angle between the vertical and the line connecting the L5/S1 joint and the trunk centre of mass, was measured using an optoelectronic system. Ten subjects performed experimental trials, each consisting of a symmetric and an asymmetric lifting task, and of a left–right lateral flexion movement. Trials were repeated and, in between trials, the IS was shifted in small steps from a location on the thorax towards a location on the sacrum. Optimal IS location was defined as the IS location with minimum root-mean-square (RMS) error between the gold standard TI and the IS TI. Averaged over subjects, the optimal IS location for symmetric and asymmetric lifting was at about 25% of the distance from the midpoint between the posterior superior iliac spines (MPSIS) to the C7 spinous process. The RMS error at this location, averaged over subjects, was 4.6±2.9°. For the left–right lateral flexion task, the optimal IS location was at about 30% of the MPSIS to C7 distance. Because in most activities of daily living, pure lateral flexion does not occur often, it is recommended place the IS at 25% of the distance from the MPSIS to C7. 相似文献
8.
Shuozhi Yang 《Computer methods in biomechanics and biomedical engineering》2013,16(3):313-322
This study evaluated the performance of a walking speed estimation system based on using an inertial measurement unit (IMU), a combination of accelerometers and gyroscopes. The walking speed estimation algorithm segments the walking sequence into individual stride cycles (two steps) based on the inverted pendulum-like behaviour of the stance leg during walking and it integrates the angular velocity and linear accelerations of the shank to determine the displacement of each stride. The evaluation was performed in both treadmill and overground walking experiments with various constraints on walking speed, step length and step frequency to provide a relatively comprehensive assessment of the system. Promising results were obtained in providing accurate and consistent walking speed/step length estimation in different walking conditions. An overall percentage root mean squared error (%RMSE) of 4.2 and 4.0% was achieved in treadmill and overground walking experiments, respectively. With an increasing interest in understanding human walking biomechanics, the IMU-based ambulatory system could provide a useful walking speed/step length measurement/control tool for constrained walking studies. 相似文献
9.
Intraoperative measurement of hip posture is the basis for assessing hip range of motion (ROM) and predicting postoperative functional limits allowable for activities of daily living. Although computer navigation for total hip arthroplasty (THA) has improved the accuracy of intraoperative ROM evaluation, it has not gained widespread popularity due to its complex and time-consuming protocol. We therefore developed an inertial measurement unit-based hip smart trial system (IMUHST) for intraoperative monitoring of hip posture. An in vitro validation experiment was conducted using bone models with a three-dimensional measurement model as the reference standard. The absolute mean error, Bland – Altman analysis and intra-class correlation coefficient demonstrated that the validity and reliability of this system meets the requirement for clinical application. Given that monitoring posture is the basis for evaluating the direction(s) of potential impingement, subluxation and dislocation, the IMUHST is a promising development direction of computer assisted surgery in THA. 相似文献
10.
L. Tagliapietra L. Modenese E. Ceseracciu C. Mazzà M. Reggiani 《Computer methods in biomechanics and biomedical engineering》2013,16(16):834-844
AbstractWearable inertial measurement units (IMUs) are a promising solution to human motion estimation. Using IMUs 3D orientations, a model-driven inverse kinematics methodology to estimate joint angles is presented. Estimated joint angles were validated against encoder-measured kinematics (robot) and against marker-based kinematics (passive mechanism). Results are promising, with RMS angular errors respectively lower than 3 and 6?deg over a minimum range of motion of 50?deg (robot) and 160?deg (passive mechanism). Moreover, a noise robustness analysis revealed that the model-driven approach reduces the effects of experimental noises, making the proposed technique particularly suitable for application in human motion analysis. 相似文献
11.
A. Nez L. Fradet T. Monnet P. Lacouture 《Computer methods in biomechanics and biomedical engineering》2017,20(14):S151-S152
12.
Total knee arthroplasty (TKA) is the most common joint replacement in the United States. Range of motion (ROM) monitoring includes idealized clinic measures (e.g. goniometry during passive ROM) that may not accurately represent knee function. Accordingly, a novel, portable, inertial measurement unit (IMU) based ROM measurement method was developed, validated, and implemented. Knee flexion was computed via relative motion between two IMUs and validated via optical motion capture (p > 0.05). Prospective analyses of 10 healthy individuals (5M, 50 ± 19 years) and 20 patients undergoing TKA (3 lost to follow up, 10M, 65 ± 6 years) were completed. Controls wore IMUs for 1-week. Patients wore IMUs for 1-week pre-TKA, 6-weeks immediately post-TKA, and 1-week at 1-year post-TKA. Flexion was computed continuously each day (8–12 h). Metrics included daily maximum flexion and flexion during stance/swing phases of gait. Maximum flexion was equal between cohorts at all time points. Contrastingly, patient stance and swing flexion were reduced pre-TKA, yet improved post-TKA. Specifically, patient stance and swing flexion were reduced below control/pre-TKA values during post-TKA week 1. Stance flexion exceeded pre-TKA and equaled control levels after week 2. However, swing flexion only exceeded pre-TKA and equaled control levels at 1-year post-TKA. This novel method improves upon the accuracy/portability of current methods (e.g. goniometry). Interestingly, surgery did not impact maximum ROM, yet improved the ability to flex during gait allowing more efficient and safe ambulation. This is the first study continuously monitoring long-term flexion before/after TKA. The results offer richer information than clinical measures about expected TKA rehabilitation. 相似文献
13.
Continuous monitoring of spine movement function could enhance our understanding of low back pain development. Wearable technologies have gained popularity as promising alternative to laboratory systems in allowing ambulatory movement analysis. This paper aims to review the state of art of current use of wearable technology to assess spine kinematics and kinetics.Four electronic databases and reference lists of relevant articles were searched to find studies employing wearable technologies to assess the spine in adults performing dynamic movements. Two reviewers independently identified relevant papers. Customised data extraction and quality appraisal form were developed to extrapolate key details and identify risk of biases of each study. Twenty-two articles were retrieved that met the inclusion criteria: 12 were deemed of medium quality (score 33.4–66.7%), and 10 of high quality (score >66.8%). The majority of articles (19/22) reported validation type studies. Only 6 reported data collection in real-life environments. Multiple sensors type were used: electrogoniometers (3/22), strain gauges based sensors (3/22), textile piezoresistive sensor (1/22) and accelerometers often used with gyroscopes and magnetometers (15/22). Two sensors units were mainly used and placing was commonly reported on the spine lumbar and sacral regions. The sensors were often wired to data transmitter/logger resulting in cumbersome systems. Outcomes were mostly reported relative to the lumbar segment and in the sagittal plane, including angles, range of motion, angular velocity, joint moments and forces.This review demonstrates the applicability of wearable technology to assess the spine, although this technique is still at an early stage of development. 相似文献
14.
Developmental coordination disorder (DCD) and attention-deficit hyperactivity disorder (ADHD) are neuro-developmental disorders, starting in childhood, which can affect the planning of movements and the coordination.We investigated how and in which measure a system based on wearable inertial measurement units (IMUs) can provide an objective support to the diagnosis of motor impairments in school-aged children.The IMUs measured linear and rotational movements of 37 schoolchildren, 7−10yo, 17 patients and 20 control subjects, during the execution of motor exercises, performed under medical and psychiatric supervision, to assess different aspects of the motor coordination.The measured motor parameters showed a high degree of significance in discriminating the ADHD/DCD patients from the healthy subjects, pointing out which motor tasks are worth focusing on. So, medical doctors have a novel key lecture to state a diagnosis, gaining in objectivity with respect to the standard procedures which mainly involve subjective human judgment.Differently to other works, we propose a novel approach in terms of number of used IMUs and of performed motor tasks. Moreover, we demonstrate the meaningful parameters to be considered as more discriminant in supporting the medical diagnosis. 相似文献
15.
《IRBM》2023,44(2):100742
ObjectivesThe characterization of the instability of gait is a current challenge of biomechanics. Indeed, risks of falling naturally result from the difficulty to control perturbations of the locomotion pattern. Hence, the assessment of a synthetic parameter able to quantify the instability in real time will be useful for the prevention of falls occurring in this context. Thus, the objective of the present study, in two steps, was to propose and evaluate a relevant parameter to quantify the risk of fallings.Material and MethodsExperimental analysis of the gait of 11 able-bodied subjects from a motion capture system in laboratory condition was performed. The distance of the Body Center of Mass (BCOM) to the Minimal Moment Axis (MMA) was computed as a proxy of whole-body angular momentum variations. In a second step, we quantified the kinematics during gait with wearable Inertial Measurement Units (IMU) fixed on two individuals (one able bodied person and one person with transfemoral amputation). We compared the IMU-based BCOM kinematics with a motion capture reference system to verify the accuracy of our measures in the field.ResultsNormative thresholds of the distance of the Body Center of Mass (BCOM) to the Minimal Moment Axis (MMA) during able-bodied level walking were assessed. The average error between the BCoM displacement computed from the IMU and from the reference vicon data of 4 mm, 3 mm and 53 mm on the mediolateral, anteroposterior and vertical axes respectively.ConclusionAll these results make it possible to consider the determination of the risks of falls in the field at mid-term. the research on an optimal configuration that maintain the performance while simplifying the device will be essential to make it acceptable by the individuals. 相似文献
16.
Studies seeking to determine the effects of gait retraining through biofeedback on peak tibial acceleration (PTA) assume that this biometric trait is a valid measure of impact loading that is reliable both within and between sessions. However, reliability and validity data were lacking for axial and resultant PTAs along the speed range of over-ground endurance running. A wearable system was developed to continuously measure 3D tibial acceleration and to detect PTAs in real-time. Thirteen rearfoot runners ran at 2.55, 3.20 and 5.10 m·s−1 over an instrumented runway in two sessions with re-attachment of the system. Intraclass correlation coefficients (ICCs) were used to determine within-session reliability. Repeatability was evaluated by paired T-tests and ICCs. Concerning validity, axial and resultant PTAs were correlated to the peak vertical impact loading rate (LR) of the ground reaction force. Additionally, speed should affect impact loading magnitude. Hence, magnitudes were compared across speeds by RM-ANOVA. Within a session, ICCs were over 0.90 and reasonable for clinical measurements. Between sessions, the magnitudes remained statistically similar with ICCs ranging from 0.50 to 0.59 for axial PTA and from 0.53 to 0.81 for resultant PTA. Peak accelerations of the lower leg segment correlated to LR with larger coefficients for axial PTA (r range: 0.64–0.84) than for the resultant PTA per speed condition. The magnitude of each impact measure increased with speed. These data suggest that PTAs registered per stand-alone system can be useful during level, over-ground, rearfoot running to evaluate impact loading in the time domain when force platforms are unavailable in studies with repeated measurements. 相似文献
17.
The purpose of this study was to establish and cross-validate a method for analyzing gait patterns determined by the center of mass (COM) through inertial sensors embedded in smart devices. The method employed an extended Kalman filter in conjunction with a quaternion rotation matrix approach to transform accelerations from the object onto the global frame. Derived by double integration, peak-to-trough changes in vertical COM position captured by a motion capture system, inertial measurement unit, and smart device were compared in terms of averaged and individual steps. The inter-rater reliability and levels of agreement for systems were discerned through intraclass correlation coefficients (ICC) and Bland–Altman plots. ICCs corresponding to inter-rater reliability were good-to-excellent for position data (ICCs,.80–.95) and acceleration data (ICCs,.54–.81). Levels of agreements were moderate for position data (LOA, 3.1–19.3%) and poor for acceleration data (LOA, 6.8%–17.8%). The Bland–Altman plots, however, revealed a small systematic error, in which peak-to-trough changes in vertical COM position were underestimated by 2.2 mm; the Kalman filter?s accuracy requires further investigation to minimize this oversight. More importantly, however, the study?s preliminary results indicate that the smart device allows for reliable COM measurements, opening up a cost-effective, user-friendly, and popular solution for remotely monitoring movement. The long-term impact of the smart device method on patient rehabilitation and therapy cannot be underestimated: not only could healthcare expenditures be curbed (smart devices being more affordable than today‘s motion sensors), but a more refined grasp of individual functioning, activity, and participation within everyday life could be attained. 相似文献
18.
The use of inertial measurement units (IMUs) for gait analysis has emerged as a tool for clinical applications. Shank gyroscope signals have been utilized to identify heel-strike and toe-off, which serve as the foundation for calculating temporal parameters of gait such as single and double limb support time. Recent publications have shown that toe-off occurs later than predicted by the dual minima method (DMM), which has been adopted as an IMU-based gait event detection algorithm. In this study, a real-time algorithm, Noise-Zero Crossing (NZC), was developed to accurately compute temporal gait parameters. Our objective was to determine the concurrent validity of temporal gait parameters derived from the NZC algorithm against parameters measured by an instrumented walkway. The accuracy and precision of temporal gait parameters derived using NZC were compared to those derived using the DMM. The results from Bland-Altman Analysis showed that the NZC algorithm had excellent agreement with the instrumented walkway for identifying the temporal gait parameters of Gait Cycle Time (GCT), Single Limb Support (SLS) time, and Double Limb Support (DLS) time. By utilizing the moment of zero shank angular velocity to identify toe-off, the NZC algorithm performed better than the DMM algorithm in measuring SLS and DLS times. Utilizing the NZC algorithm’s gait event detection preserves DLS time, which has significant clinical implications for pathologic gait assessment. 相似文献
19.
J. Favre R. Aissaoui B.M. Jolles J.A. de Guise K. Aminian 《Journal of biomechanics》2009,42(14):2330-2335
Measurement of three-dimensional (3D) knee joint angle outside a laboratory is of benefit in clinical examination and therapeutic treatment comparison. Although several motion capture devices exist, there is a need for an ambulatory system that could be used in routine practice. Up-to-date, inertial measurement units (IMUs) have proven to be suitable for unconstrained measurement of knee joint differential orientation. Nevertheless, this differential orientation should be converted into three reliable and clinically interpretable angles. Thus, the aim of this study was to propose a new calibration procedure adapted for the joint coordinate system (JCS), which required only IMUs data. The repeatability of the calibration procedure, as well as the errors in the measurement of 3D knee angle during gait in comparison to a reference system were assessed on eight healthy subjects. The new procedure relying on active and passive movements reported a high repeatability of the mean values (offset<1°) and angular patterns (SD<0.3° and CMC>0.9). In comparison to the reference system, this functional procedure showed high precision (SD<2° and CC>0.75) and moderate accuracy (between 4.0° and 8.1°) for the three knee angle. The combination of the inertial-based system with the functional calibration procedure proposed here resulted in a promising tool for the measurement of 3D knee joint angle. Moreover, this method could be adapted to measure other complex joint, such as ankle or elbow. 相似文献
20.
This study aimed to investigate effects of walking direction and speed on gait complexity, symmetry and variability as indicators of neural control mechanisms, and if a period of backward walking has acute effects on forward walking. Twenty-two young adults attended 2 visits. In each visit participants walked forwards at preferred walking speed (PWS) for 3-minutes (pre) followed by 5-minutes walking each at 80%, 100% and 120% of PWS of either forward or backward walking then a further 3-minutes walking forward at PWS (post). The order of walking speed in each visit was randomised and walking direction of each visit was randomised. An inertial measurement unit was placed over L5 vertebra to record tri-axial accelerations. From the trunk accelerations multiscale entropy, harmonic ratio and stride time variability were calculated to measure complexity, symmetry and variability for each walk. Complexity increased with increasing walking speed for all axes in forward and backward walking, and backward walking was less complex than forward walking. Stride time variability was also greater in backward than forward walking. Anterio-posterior and medio-lateral complexity increased following forward and backward walking but there was no difference between forward and backward walking post effects. No effects were found for harmonic ratio. These results suggest during backward walking trunk motion is rigidly controlled but central pattern generators responsible for temporal gait patterns are less refined for backward walking. However, in both directions complexity increased as speed increased suggesting additional constraint of trunk motion, normally characterised by reduced complexity, is not applied as speed increases. 相似文献