微生物燃料电池利用乳酸产电性能与微生物群落分布特征

【目的】为探讨以乳酸为基质的微生物燃料电池(Microbial fuel cell,MFC)产电性能以及微生物群落在阳极膜、悬浮液、阳极沉淀污泥中的分布特征,【方法】试验建立了双室MFC,以乳酸为阳极主要碳源,研究了反应器的启动过程及产电效能,同时以电镜和PCR-变性梯度凝胶电泳(Denaturing gradient gelelectrophoresis,DGGE)技术解析了微生物群落的空间分布特征。【结果】结果表明,反应器启动第7天时外电压达到0.56 V,当外阻为80Ω时,电流密度为415 mA/m2,MFC的功率密度达到最大值82 mW/m2。电镜观察发现大量杆菌附着在阳极表面,结合较为紧密;DGGE图谱显示阳极膜表面微生物与种泥最为相似,与阳极悬浮液、底部沉淀污泥中的主要菌群一致,条带序列与睾丸酮丛毛单胞菌(Comamonas testosteroni)和布氏弓形菌(Arcobacter butzleri)等最为相似。【结论】本研究表明以乳酸为基质MFC可产生较高的功率密度,阳极附着的优势菌与接种污泥来源密切相关。     

Enhancement of extracellular electron transfer and bioelectricity output by synthetic porin

The microbial fuel cell (MFC), is a promising environmental biotechnology for harvesting electricity energy from organic wastes. However, low bacterial membrane permeability of electron shuttles is a limiting factor that restricts the electron shuttle‐mediated extracellular electron transfer (EET) from bacteria to electrodes, thus the electricity power output of MFCs. To this end, we heterologously expressed a porin protein OprF from Pseudomonas aeruginosa PAO1 into Escherichia coli, which dramatically increased its membrane permeability, delivering a much higher current output in MFCs than its parental strain (BL21). We found that the oprF‐expression strain showed more efficient EET than its parental strain. More strikingly, the enhanced membrane permeability also rendered the oprF‐expression strain an efficient usage of riboflavin as the electron shuttle, whereas its parental strain was incapable of. Our results substantiated that membrane permeability is crucial for the efficient EET, and indicated that the expression of synthetic porins could be an efficient strategy to enhance bioelectricity generation by microorganisms (including electrogenic bacteria) in MFCs. Biotechnol. Bioeng. 2013; 110: 408–416. © 2012 Wiley Periodicals, Inc.     

A state of the art review on microbial fuel cells: A promising technology for wastewater treatment and bioenergy

A microbial fuel cell (MFC) is a bioreactor that converts chemical energy in the chemical bonds in organic compounds to electrical energy through catalytic reactions of microorganisms under anaerobic conditions. It has been known for many years that it is possible to generate electricity directly by using bacteria to break down organic substrates. The recent energy crisis has reinvigorated interests in MFCs among academic researchers as a way to generate electric power or hydrogen from biomass without a net carbon emission into the ecosystem. MFCs can also be used in wastewater treatment facilities to break down organic matters. They have also been studied for applications as biosensors such as sensors for biological oxygen demand monitoring. Power output and Coulombic efficiency are significantly affected by the types of microbe in the anodic chamber of an MFC, configuration of the MFC and operating conditions. Currently, real-world applications of MFCs are limited because of their low power density level of several thousand mW/m2. Efforts are being made to improve the performance and reduce the construction and operating costs of MFCs. This article presents a critical review on the recent advances in MFC research with emphases on MFC configurations and performances.     

Thionine increases electricity generation from microbial fuel cell using Saccharomyces cerevisiae and exoelectrogenic mixed culture

Microbial fuel cells (MFCs) have been shown to be capable of clean energy production through the oxidation of biodegradable organic waste using various bacterial species as biocatalysts. In this study we found Saccharomyces cerevisiae, previously known electrochemcially inactive or less active species, can be acclimated with an electron mediator thionine for electrogenic biofilm formation in MFC, and electricity production is improved with facilitation of electron transfer. Power generation of MFC was also significantly increased by thionine with both aerated and non-aerated cathode. With electrochemically active biofilm enriched with swine wastewater, MFC power increased more significantly by addition of thionine. The optimum mediator concentration was 500 mM of thionine with S. cerevisae in MFC with the maximum voltage and current generation in the microbial fuel cell were 420 mV and 700 mA/m(2), respectively. Cyclic voltametry shows that thionine improves oxidizing and reducing capability in both pure culture and acclimated biofilm as compared to non-mediated cell. The results obtained indicated that thionine has great potential to enhance power generation from unmediated yeast or electrochemically active biofilm in MFC.     

Microorganism-immobilized carbon nanoparticle anode for microbial fuel cells based on direct electron transfer

A fast and convenient bacterial immobilization method was proposed as an attempt to improve the anode efficiency of a microbial fuel cell, in which bacteria were entrapped into carbon nanoparticle matrix. The direct electron transfer from the entrapped bacterial cells to the anode was verified using cyclic voltammogram (CV). Using the immobilized bioanode, the start-up time of the MFC was greatly reduced. Meanwhile, the maximum power density of 1,947 mW m⁻² with the modified anode was much higher than that with the biofilm-based carbon cloth anode (1,479 mW m⁻²). Impedance measurements suggested that performance improvement resulted from the decrease in charge transfer and diffusion resistances. The results demonstrated that bacteria immobilization using carbon nanoparticle matrix was a simple and efficient approach for improving the anodes performances in MFCs.     

Loading rate and external resistance control the electricity generation of microbial fuel cells with different three-dimensional anodes

The electricity generation, electrochemical and microbial characteristics of five microbial fuel cells (MFCs) with different three-dimensional electrodes (graphite and carbon felt, 2mm and 5mm graphite granules and graphite wool) was examined in relation to the applied loading rate and the external resistance. The graphite felt electrode yielded the highest maximum power output amounting up to 386Wm(-3) total anode compartment (TAC). However, based on the continuous current generation, limited differences between the materials were registered. Doubling the loading rate to 3.3gCODL(-1)TACd(-1) resulted only in an increased current generation when the external resistance was low (10.5-25Omega) or during polarization. Conversely, lowering the external resistance resulted in a steady increase of both the kinetic capacities of the biocatalyst and the continuous current generation from 77 (50Omega) up to 253 (10.5Omega)Am(-3)TAC. Operating a MFC at an external resistance close to its internal resistance, allows to increase the current generation from enhanced loading rates while maximizing the power generation.     

固定化植物乳杆菌的制备及其发酵条件优化

采用海藻酸钠包埋植物乳杆菌并通过测定固定化细胞发酵清液的抑菌效果,优化得到的固定化最佳工艺条件为:海藻酸钠浓度为3%,CaCl2浓度为1.5%,菌悬液体积为3.5 mL(4.0×108 cfu/mL).固定化细胞重复发酵多批次效果良好.固定化细胞发酵条件优化结果表明:最适pH为7.0,最适温度为36℃,培养基中添加0....     

Microbial fuel cells as an alternative energy source: current status

Microbial fuel cell (MFC) technology is an emerging area for alternative renewable energy generation and it offers additional opportunities for environmental bioremediation. Recent scientific studies have focused on MFC reactor design as well as reactor operations to increase energy output. The advancement in alternative MFC models and their performance in recent years reflect the interests of scientific community to exploit this technology for wider practical applications and environmental benefit. This is reflected in the diversity of the substrates available for use in MFCs at an economically viable level. This review provides an overview of the commonly used MFC designs and materials along with the basic operating parameters that have been developed in recent years. Still, many limitations and challenges exist for MFC development that needs to be further addressed to make them economically feasible for general use. These include continued improvements in fuel cell design and efficiency as well scale-up with economically practical applications tailored to local needs.     

A novel alginate hollow fiber bioreactor process for cellular therapy applications

Gel‐matrix culture environments provide tissue engineering scaffolds and cues that guide cell differentiation. For many cellular therapy applications such as for the production of islet‐like clusters to treat Type 1 diabetes, the need for large‐scale production can be anticipated. The throughput of the commonly used nozzle‐based devices for cell encapsulation is limited by the rate of droplet formation to ～0.5 L/h. This work describes a novel process for larger‐scale batch immobilization of mammalian cells in alginate‐filled hollow fiber bioreactors (AHFBRs). A methodology was developed whereby (1) alginate obstruction of the intra‐capillary space medium flow was negligible, (2) extra‐capillary alginate gelling was complete and (3) 83 ± 4% of the cells seeded and immobilized were recovered from the bioreactor. Chinese hamster ovary (CHO) cells were used as a model aggregate‐forming cell line that grew from mostly single cells to pancreatic islet‐sized spheroids in 8 days of AHFBR culture. CHO cell growth and metabolic rates in the AHFBR were comparable to small‐scale alginate slab controls. Then, the process was applied successfully to the culture of primary neonatal pancreatic porcine cells, without significant differences in cell viability compared with slab controls. As expected, alginate‐immobilized culture in the AHFBR increased the insulin content of these cells compared with suspension culture. The AHFBR process could be refined by adding matrix components or adapted to other reversible gels and cell types, providing a practical means for gel‐matrix assisted cultures for cellular therapy. © 2009 American Institute of Chemical Engineers Biotechnol. Prog., 2009     

Effect of operating modes on simultaneous anaerobic sulfide and nitrate removal in microbial fuel cell

The effect of operating modes on the simultaneous sulfide and nitrate removal were studied in two-chamber microbial fuel cells (MFCs). The batch and continuous operating modes were compared and evaluated in terms of substrate removal and electricity generation. Upon gradual increase in the influent sulfide concentration from 60 to 1,020 S mg L^?1, and the hydraulic retention time decrease from 17.2 to 6 h, the MFC accomplished a good substrate removal efficiency whereby nitrogen and sulfate were the main end products. The removal efficiency of the MFC in the continuous mode was much higher than that in the batch mode, and its current densities in the continuous mode were more stable and higher than in the batch mode, which could be explained by the linear relationship between electrons released by the substrates and accepted on the electrodes. The electricity output in the continuous mode of the MFC was higher than that in the batch mode. MFC's operation in the continuous mode was a better strategy for the simultaneous treatment of sulfide and nitrate.     

An electricity-generating prosthecate bacterium strain Mfc52 isolated from a microbial fuel cell

Rod-shaped Alphaproteobacteria possessing long prosthecae-like appendages have been detected abundantly in biofilms attaching onto anode graphite of cellulose-fed microbial fuel cells (MFCs). To identify their ecological roles, the present study isolated a corresponding bacterium (strain Mfc52) by direct plating of a biofilm suspension onto a solid medium containing glucose and ferric ion. Phylogenetic analysis revealed that this strain is deeply branched in the class Alphaproteobacteria and may represent a novel order. Strain Mfc52 fermented sugars and produced lactate, acetate, and fumarate, whereas ferric ion stimulated the growth on glucose. When an MFC was inoculated with this strain and supplemented with glucose, it fermented glucose and generated electricity by oxidizing organic acids produced from glucose. Electron micrographs showed that a fraction of cells in a liquid culture had prosthecae-like appendages that were abundantly observed in anode biofilm. These observations suggest that the bacterial population represented by strain Mfc52 shared an important niche in the cellulose-fed MFC, where it generated electricity by oxidizing intermediate metabolites from cellulose degradation.     

Critical factors affecting ethanol production by immobilized Pichia stipitis using corn cob hemicellulosic hydrolysate

Fermentation of xylose from hydrolysate of acid-treated corn cob by Pichia stipitis is inhibited by acetic acid and lignin derivatives. In the present study, we have designed and implemented an immobilized cell culture for xylose to ethanol conversion from acid-treated corn cob hydrolysate without the removal of fermentation inhibitors. In this study, cultivations of suspended and immobilized Pichia were compared in terms of ethanol yield and productivity to investigate whether the cell immobilization could improve resistance to inhibitors. Cell immobilization clearly favored the fermentative metabolism in nondetoxified corn cob hydrolysate leading to an improvement of twofold ethanol productivity as compared to that achieved with suspension culture. Calcium alginate as an immobilization matrix was selected to immobilize Pichia cells. Concentrations of sodium alginate, calcium chloride, and fermentor agitation speed were optimized for ethanol production using statistical method. Statistical analysis showed that agitation speed had maximum influence on ethanol production by immobilized Pichia cells. In comparison to suspension culture, immobilization had a positive impact on the fermentative metabolism of Pichia, improving the ethanol yield from 0.40 to 0.43?g/g and productivity from 0.31 to 0.51?g/L/h for acid-treated corn cob hydrolysate.     

Layer-by-layer construction of graphene-based microbial fuel cell for improved power generation and methyl orange removal

Development of highly efficient anode is critical for enhancing the power output of microbial fuel cells (MFCs). The aim of this work is to investigate whether modification of carbon paper (CP) anode with graphene (GR) via layer-by-layer assembly technique is an effective approach to promote the electricity generation and methyl orange removal in MFCs. Using cyclic voltammetry and electrochemical impedance spectroscopy, the GR/CP electrode exhibited better electrochemical behavior. Scanning electron microscopy results revealed that the surface roughness of GR/CP increased, which was favorable for more bacteria to attach to the anode surface. The MFCs equipped with GR/CP anode achieved a stable maximum power density of 368 mW m^?2 under 1,000 Ω external resistance and a start time for the initial maximum voltage of 180 h, which were, respectively, 51 % higher and 31 % shorter than the corresponding values of the MFCs with blank anode. The anode and cathode polarization curves revealed negligible difference in cathode potentials but obviously difference in anode potentials, indicating that the GR-modified anode other than the cathode was responsible for the performance improvement of MFC. Meanwhile, compared with MFCs with blank anode, 11 % higher decolorization efficiency and 16 % higher the chemical oxygen demand removal rate were achieved in MFC with GR-modified anode during electricity generation. This study might provide an effective way to modify the anode for enhanced electricity generation and efficient removal of azo dye in MFCs.     

Influence of anodic biofilm growth on bioelectricity production in single chambered mediatorless microbial fuel cell using mixed anaerobic consortia

The effect of anodic biofilm growth and extent of its coverage on the anodic surface of a single chambered mediatorless microbial fuel cell (MFC) was evaluated for bioelectricity generation using designed synthetic wastewater (DSW) and chemical wastewater (CW) as substrates and anaerobic mixed consortia as biocatalyst. Three MFCs (plain graphite electrodes, air cathode, Nafion membrane) were operated separately with variable biofilm coverage [control; anode surface coverage (ASC), 0%], partially developed biofilm [PDB; ASC approximately 44%; 90 days] and fully developed biofilm [FDB; ASC approximately 96%; 180 days] under acidophilic conditions (pH 6) at room temperature. The study depicted the effectiveness of anodic biofilm formation in enhancing the extracellular electron transfer in the absence of mediators. Higher specific power production [29mW/kg COD(R) (CW and DSW)], specific energy yield [100.46J/kg VSS (CW)], specific power yield [0.245W/kg VSS (DSW); 0.282W/kg VSS (CW)] and substrate removal efficiency of 66.07% (substrate degradation rate, 0.903kgCOD/m(3)-day) along with effective functioning fuel cell at relatively higher resistance [4.5kOmega (DSW); 14.9kOmega (CW)] correspond to sustainable power [0.008mW (DSW); 0.021mW (CW)] and effective electron discharge (at higher resistance) and recovery (Coulomb efficiency; 27.03%) were observed especially with FDB operation. Cyclic voltammetry analysis documented six-fold increment in energy output from control (1.812mJ) to PDB (10.666mJ) operations and about eight-fold increment in energy from PDB to FDB (86.856mJ). Biofilm configured MFC was shown to have the potential to selectively support the growth of electrogenic bacteria with robust characteristics, capable of generating higher power yields along with substrate degradation especially operated with characteristically complex wastewaters as substrates.     

Optimization of a Pt-free cathode suitable for practical applications of microbial fuel cells

Microbial fuel cells (MFCs) are considered as a promising way for the direct extraction of biochemical energy from biomass into electricity. However, scaling up the process for practical applications and mainly for wastewater treatment is an issue because there is a necessity to get rid of unsustainable platinum (Pt) catalyst. In this study, we developed a low-cost cathode for a MFC making use of sputter-deposited cobalt (Co) as the catalyst and different types of cathode architecture were tested in a single-chambered air-cathode MFC. By sputtering the catalyst on the air-side of the cathode, increased contact with ambient oxygen significantly resulted in higher electricity generation. This outcome was different from previous studies using conventionally-coated Pt cathodes, which was due to the different technology used.     

Microfabricated Microbial Fuel Cell Arrays Reveal Electrochemically Active Microbes

Microbial fuel cells (MFCs) are remarkable “green energy” devices that exploit microbes to generate electricity from organic compounds. MFC devices currently being used and studied do not generate sufficient power to support widespread and cost-effective applications. Hence, research has focused on strategies to enhance the power output of the MFC devices, including exploring more electrochemically active microbes to expand the few already known electricigen families. However, most of the MFC devices are not compatible with high throughput screening for finding microbes with higher electricity generation capabilities. Here, we describe the development of a microfabricated MFC array, a compact and user-friendly platform for the identification and characterization of electrochemically active microbes. The MFC array consists of 24 integrated anode and cathode chambers, which function as 24 independent miniature MFCs and support direct and parallel comparisons of microbial electrochemical activities. The electricity generation profiles of spatially distinct MFC chambers on the array loaded with Shewanella oneidensis MR-1 differed by less than 8%. A screen of environmental microbes using the array identified an isolate that was related to Shewanella putrefaciens IR-1 and Shewanella sp. MR-7, and displayed 2.3-fold higher power output than the S. oneidensis MR-1 reference strain. Therefore, the utility of the MFC array was demonstrated.     

Electricity generation from carbon monoxide and syngas in a microbial fuel cell

Electricity generation in microbial fuel cells (MFCs) has been a subject of significant research efforts. MFCs employ the ability of electricigenic bacteria to oxidize organic substrates using an electrode as an electron acceptor. While MFC application for electricity production from a variety of organic sources has been demonstrated, very little research on electricity production from carbon monoxide and synthesis gas (syngas) in an MFC has been reported. Although most of the syngas today is produced from non-renewable sources, syngas production from renewable biomass or poorly degradable organic matter makes energy generation from syngas a sustainable process, which combines energy production with the reprocessing of solid wastes. An MFC-based process of syngas conversion to electricity might offer a number of advantages such as high Coulombic efficiency and biocatalytic activity in the presence of carbon monoxide and sulfur components. This paper presents a discussion on microorganisms and reactor designs that can be used for operating an MFC on syngas.     

Gaseous pollutant treatment and electricity generation in microbial fuel cells (MFCs) utilising redox mediators

Microbial fuel cell (MFC) is an emerging technology for sustainable energy generation and waste treatment. This paper reviews the potential of a gaseous substrate when it is combined with a mediator in an MFC to generate electricity and to treat toxic gaseous pollutants. Most MFCs for waste water treatment often cannot use mediator to enhance the electron transfer from the microbe to the anode because of the difficulty in recovering the expensive and potentially toxic compound. Combining gas feeds with mediators is possible since the soluble mediator would remain in the anode chamber as the gas passes through the reactor. In addition, this type of MFC is possible to be integrated into an anaerobic biofiltration system (BF-MFC), where the biofilter removes the gaseous contaminant and produces the reduced mediator and the MFC produces the electricity and recycles the reoxidised mediator. This paper also talks about the past research on gaseous feed MFCs, and reviews the mechanism and strategies of electron transfer in MFC using redox mediator. The advantages, process parameters and challenges of BF-MFC are discussed. This knowledge is very much required in the design and scale up of BF-MFC. This paper will be useful for those who work in the area of gaseous pollutant treatment and electricity generation.     

Bioelectricity production from wastewater treatment in dual chambered microbial fuel cell (MFC) using selectively enriched mixed microflora: Effect of catholyte

The performance of aerated and ferricyanide catholytes on the bioelectricity production was evaluated in dual chambered microbial fuel cell (MFC) (mediatroless anode; graphite electrodes) employing selectively enriched H(2) producing mixed consortia as anodic inoculum. Two MFCs with aerated catholyte (MFC(AC)) and ferricyanide catholyte (MFC(FC)) were operated separately to elucidate the difference in power generation potential and carbon removal efficiency under similar operating conditions [ambient pressure; room temperature (28+/-2 degrees C); acidophilic microenvironment (pH 6)]. The experimental data demonstrated the feasibility of in situ bioelectricity generation along with wastewater treatment. Effective power generation and substrate removal efficiency was documented in the fuel cell operated with ferricyanide catholyte (586 mV; 2.37 mA; 0.559 kg COD/m(3) day) than aerated catholyte (572 mV; 1.68 mA; 0.464 kg COD/m(3) day). Maximum power yield (0.635 W/kg COD(R) and 0.440 W/kg COD(R)) and current density (222.59 mA/m(2) and 190.28 mA/m(2)) was observed at 100 Omega resistor with ferricyanide and aerated catholytes, respectively. The study documented both wastewater treatment and electricity production through direct conversion of H(2) in a single system.     

Effect of enrichment procedures on performance and microbial diversity of microbial fuel cell for Congo red decolorization and electricity generation

The purpose of this study was to determine the effect of enrichment procedure on the performance and microbial diversity of an air-cathode microbial fuel cell (MFC) which was explored for simultaneous azo dye decolorization and electricity generation. Two different enrichment procedures in which glucose and Congo red were added into the MFCs sequentially (EP1) or simultaneously (EP2) were tested by operating parallel MFCs independently for more than 6 months. The power density, electrode potential, Congo red decolorization, biofilm morphology, and bacterial diversity of the MFCs under the two enrichment procedures were compared and investigated. The results showed that the enrichment procedures have a negligible effect on the dye decolorization, but significantly affected the electricity generation. More than 90% decolorization at dye concentration of 300 mg/L was achieved within 170 h for the two tested enrichment procedures. However, the MFC with EP2 achieved a maximum power density of 192 mW/m², which was 75% higher than that of the MFC with EP1 (110 mW/m²). The depressed surfaces of the bacteria in the MFC with EP1 indicated the allergic response caused by the subsequent addition of Congo red. 16S rRNA sequencing analysis demonstrated a phylogenetic diversity in the communities of the anode biofilm and showed clear differences between the anode-attached populations in the MFCs with a different enrichment procedure. This study suggests that the enrichment procedure is important for the MFC explored for simultaneous dye decolorization and electricity generation.