Continuous degradation of maltose by enzyme entrapment technology using calcium alginate beads as a matrix

Maltase from Bacillus licheniformis KIBGE-IB4 was immobilized within calcium alginate beads using entrapment technique. Immobilized maltase showed maximum immobilization yield with 4% sodium alginate and 0.2 M calcium chloride within 90.0 min of curing time. Entrapment increases the enzyme–substrate reaction time and temperature from 5.0 to 10.0 min and 45 °C to 50 °C, respectively as compared to its free counterpart. However, pH optima remained same for maltose hydrolysis. Diffusional limitation of substrate (maltose) caused a declined in V_max of immobilized enzyme from 8411.0 to 4919.0 U ml^?1 min^?1 whereas, K_m apparently increased from 1.71 to 3.17 mM ml^?1. Immobilization also increased the stability of free maltase against a broad temperature range and enzyme retained 45% and 32% activity at 55 °C and 60 °C, respectively after 90.0 min. Immobilized enzyme also exhibited recycling efficiency more than six cycles and retained 17% of its initial activity even after 6th cycles. Immobilized enzyme showed relatively better storage stability at 4 °C and 30 °C after 60.0 days as compared to free enzyme.     

Production of xylo-oligosaccharides by immobilized-stabilized derivatives of endo-xylanase from Streptomyces halstedii

An endoxylanase from Streptomyces halstedii was stabilized by multipoint covalent immobilization on glyoxyl-agarose supports. The immobilized enzyme derivatives preserved 65% of the catalytic activity corresponding to the one of soluble enzyme that had been immobilized. These immobilized derivatives were 200 times more stable 200 times more stable than the one-point covalently immobilized derivative in experiments involving thermal inactivation at 60 °C. The activity and stability of the immobilized enzyme was higher at pH 5.0 than at pH 7.0. The optimal temperature for xylan hydrolysis was 10 °C higher for the stabilized derivative than for the non-stabilized derivative. On the other hand, the highest loading capacity of activated 10% agarose gels was 75 mg of enzyme per mL of support. To prevent diffusional limitations, low loaded derivatives (containing 0.2 mg of enzyme per mL of support) were used to study the hydrolysis of xylan at high concentration (close to 1% (w/v)). 80% of the reducing sugars were released after 3 h at 55 °C. After 80% of enzymatic hydrolysis, a mixture of small xylo-oligosaccharides was obtained (from xylobiose to xylohexose) with a high percentage of xylobiose and minimal amounts of xylose. The immobilized-stabilized derivatives were used for 10 reaction cycles with no loss of catalytic activity.     

Stabilization of a raw starch digesting amylase from Aspergillus carbonarius via immobilization on activated and non-activated agarose gel

Applications of raw starch digesting amylases (RSDAs) are limited due to instability, product inhibition of enzyme and contamination. RSDA from Aspergillus carbonarius was stabilized through immobilization on agarose gel by adsorption, spontaneous crosslinking and conjugation using glycidol, glutaraldehyde or polyglutaraldehyde. Effects of immobilization on kinetics, catalytic, storage and operational stability of immobilized enzyme were evaluated. Polyglutaraldehyde activated agarose RSDA (PGAg-RSDA) gave the highest immobilization yield (100%) with expressed activity of 86.7% while that of glycidol activated RSDA (GlyAg-RSDA) was 80.4%. A shift in pH from optimum of 5 for the soluble enzyme to 6 for RSDA adsorbed on agarose followed by crosslinking with glutaraldehyde (AgRSDA-CROSS) and simultaneous adsorption and crosslinking (AgRSDA-RET), and pH 7 for PGAg-RSDA was seen. PGAg-RSDA and AgRSDA-CROSS were most pH stable and retained over 82% of their activities between pH 3.5 and 9 compared to 59% for the soluble enzyme. Thermoinactivation studies showed that immobilized RSDAs with the exception of GAg-RSDA retained over 90% of their activities at 60°C for 120 min while soluble enzyme retained only 76% activity under the same condition. AgRSDA-CROSS, PGAg-RSDA, Gly-RSDA and GAg-RSDA retained approximately 100% of their activities after 30 days storage at 4°C. GlyAg-RSDA retained 99.6%, PGAg-RSDA 94%, AgRSDA-CROSS 90%, GAg-RSDA 86.5% and Ag-RSDA-RET 80% activity after 10 batch reactions. Immobilization stabilized RSDA and permits processing at higher temperatures to reduce contamination.     

Purification and biochemical characterization of a novel SDS and surfactant stable,raw starch digesting,and halophilic α-amylase from a moderately halophilic bacterium,Nesterenkonia sp. strain F

An extracellular halophilic α-amylase from Nesterenkonia sp. strain F was purified to homogeneity by 80% ethanol precipitation, Q-Sepharose anion exchange and Sephacryl S-200 gel filtration chromatography, with a 10.8-fold increase in specific activity. The molecular mass of the amylase was estimated to be 100 kDa and 106 kDa by SDS–PAGE and gel filtration chromatography, respectively. The enzyme showed maximal activity at pH 7.5 and 45 °C. The amylase was active in a wide range of salt concentrations (0–4 M) with its maximum activity at 0.5 M NaCl or 1 M KCl and was stable at the salts concentrations between 1 M and 4 M. Fe³⁺, Cu²⁺, Zn²⁺ and Al³⁺ strongly inhibited the enzyme, whereas Ca²⁺ stimulated the amylase activity. The α-amylase was inhibited by EDTA, but was not inhibited by PMSF and β-mercaptoethanol. The enzyme showed remarkable stability towards 0.5% SDS and sarcosyl, and 2% each of Triton X-100, Tween 80 and Tween 20. K_m value of the amylase for soluble starch was 4.5 mg/ml. The amylase hydrolyzed 38% of raw wheat starch and 20% of corn starch in a period of 48 h. The major products of soluble starch hydrolysis were maltose, maltotriose and maltotetraose, indicating an α-amylase activity.     

Hydrolytic enzymes production by Aspergillus section Nigri in presence of butylated hydroxyanisole and propyl paraben on peanut meal extract agar

BackgroundIn the last years, food grade antioxidants are used safely as an alternative to traditional fungicides to control fungal growth in several food and agricultural products.AimsIn this work, the effect of butylated hydroxyanisole (BHA) and propyl paraben (PP) on two hydrolytic enzyme activity (β-d-glucosidase and α-d-galactosidase) by Aspergillus section Nigri species under different water activity conditions (a_W; 0.98, 0.95 and 0.93) and incubation time intervals (24, 48, 72 and 96 h) was evaluated on peanut-based medium.MethodsThe activity of two glycosidases, β-d-glucosidase and α-d-galactosidase, was assayed using as substrates 4-nitrophenyl-β-d-glucopyranosido and 4-nitrophenyl-α-d-galactopyranosido, respectively. The enzyme activity was determined by the increase in optical density at 405 nm caused by the liberation of p-nitrophenol by enzymatic hydrolysis of the substrate. Enzyme activity was expressed as micromoles of p-nitrophenol released per minute.ResultsThe major inhibition in β-d-glucosidase activity of A. carbonarius and A. niger was found with 20 mmol l⁻¹ of BHA or PP at 0.98 and 0.95 a_W, respectively, whereas for α-d-galactosidase activity a significant decrease in enzyme activity with respect to control was observed in A. carbonarius among 5 to 20 mmol l⁻¹ of BHA or PP in all conditions assayed. Regarding A. niger, the highest percentages of enzyme inhibition activity were found with 20 mmol l⁻¹ of BHA or PP at 0.95 a_W and 96 h.ConclusionsThe results of this work provide information about the capacity of BHA and PP to inhibit in vitro conditions two of the most important hydrolytic enzymes produced by A. carbonarius and A. niger species.     

Site-directing an intense multipoint covalent attachment (MCA) of mutants of the Geobacillus thermocatenulatus lipase 2 (BTL2): Genetic and chemical amination plus immobilization on a tailor-made support

Immobilized enzymes are preferred over their soluble counterparts due to their robustness in harsh industrial processes; the most stable enzyme derivatives are often produced through multipoint covalent attachment (MCA). However, most enzymes are unable to establish optimal MCA to electrophile-type supports given the heterogeneous distribution and/or low content of primary amino groups on their surfaces; this restricts both the diversity of areas prone to react and the number of attachments to the support. To overcome this we propose combining site-directed immobilization and protein engineering to increase the number of bonds between a specific enzyme surface and a tailor-made support. We applied this novel strategy to engineered mutants of the lipase 2 from Geobacillus thermocatenulatus with one Cys exposed residue, that after genetic amination and/or chemical amination, were immobilized on glyoxyl-disulfide support using a site-directed MCA protocol. Two highly stabilized derivatives of chemically aminated lipase variants, in which site-directed MCA implied the surrounding surface of residues Cys344 or Cys40, were produced: the first one was 2.4-fold more productive than the reference derivative (648 g of hydrolyzed ester); the second derivative was 40% more selective (EPA/DHA molar ratio) and as active (1 μmol g catalyst⁻¹ min⁻¹) as the reference in the production of PUFAs.     

Amylolytically-resistant tapioca starch modified by combined treatment of branching enzyme and maltogenic amylase

Tapioca starch was modified using branching enzyme (BE) isolated from Bacillus subtilis 168 and Bacillus stearothermophilus maltogenic amylase (BSMA), and their molecular fine structure and susceptibility to amylolytic enzymes were investigated. By BE treatment, the molecular weight decreased from 3.1 × 10⁸ to 1.7 × 10⁶, the number of shorter branch chains (DP 6–12) increased, the number of longer branch chains (DP >25) decreased, and amylose content decreased from 18.9% to 0.75%. This indicated that α–1,4 linkages of amylose and amylopectin were cleaved, and moiety of glycosyl residues were transferred to another amylose and amylopectin to produce branched glucan and BE-treated tapioca starch by forming α–1,6 branch linkages. The product was further modified with BSMA to produce highly-branched tapioca starch with 9.7% of extra branch points. When subject to digestion with human pancreatic α-amylase (HPA), porcine pancreatic α-amylase (PPA) and glucoamylase, highly-branched tapioca starch gave significantly lowered α-amylase susceptibility (7.5 times, 14.4 times and 3.9 times, respectively), compared to native tapioca starch.     

Psychrophilic α-amylase from Aeromonas veronii NS07 isolated from farm soils

Among 120 isolates examined in this study, three isolates were selected for amylase production on starch agar plates following incubation at 10 °C. Identification by 16SrRNA on selected bacterium disclosed the highest similarity for protean regions of this gene as Aeromonas veronii NS07. A 63 kDa psychrophilic amylase enzyme from NS07 strain was purified by two-steps chromatography. The enzyme had the highest specific activity at pH 4 and was active at the range of temperatures from 0 to 50 °C, although the optimum temperature for enzyme activity was found at 10 °C. Analysis of the N-terminal amino acid sequencing disclosed 20 amino acids from purified amylase which had no similarity with other known α-amylases, indicating that the presented enzyme was novel. Amylase activity was enhanced in relation to optimum activity with the presence of sodium sulphate (161%), MnCl₂ (298%), CaCl₂ (175%), FeCl₂ (182%), MgCl₂ (237%), ZnCl₂ (169%), NiCl₂ (139%), NaCl (158%), each at 5 mM, while EDTA, phenylmethane sulphonylfluoride (PMSF) (3 mM), urea (8 M) and SDS (1%) inhibited the enzyme up to 5%, 2%, 80% and 18%, respectively. NS07 strain seems to be suitable as biocatalyst for practical use in liquefaction of starch at low temperatures, detergent and textile industries.     

Immobilization of maltogenase onto polyurethane microparticles from poly(vinyl alcohol) and hexamethylene diisocyanate

A series of porous polyurethane (PU) microparticles from poly(vinyl alcohol) (PVA) and hexamethylene diisocyanate (HMDI) using different ratios of components were obtained by one step method. Molar compositions of PU microparticles were estimated by determination of nitrogen, isocyanate and hydroxyl groups. PU carriers which were synthesized using optimal initial molar ratios of PVA and HMDI were applied for immobilization of maltogenase (MG) from Bacillus stearothermophilus. Immobilized enzyme exhibited higher catalytic activity and enhanced temperature stability in comparison with the native MG. Maximal loading 7.78 mg/g wet carrier was reached when PU microparticles with initial molar ratio of PVA and HMDI = 1:3 was used as a carrier for immobilization. The high efficiency of immobilization (EI) was obtained using PU microparticles when initial molar ratio of HMDI and PVA was 1:1–1:10. High stability of MG immobilized onto PU microparticles during storage was demonstrated. Immobilized starch hydrolyzing enzyme was successfully tested in batch and column type reactors for hydrolysis of potato starch. MG immobilized onto PU enables easy separation from the reaction medium and reuse of the immobilized preparation over seven reaction cycles in bath operation and at least three cycles in column type reactor.     

Activity and stability of different immobilized preparations of recombinant E. coli cells containing ω-transaminase

Production of chiral amines using ω-transaminases has been thoroughly studied in recent years. Immobilized ω-transaminases, however, have been used on relatively few occasions despite potential benefits such as reuse of enzyme and ease of product purification. In this study principally different methods including surface immobilization, entrapment and sweep flocculation using titanium oxide, Ca-alginate and chitosan respectively were evaluated for the immobilization of recombinant Escherichia coli cells. The enzyme expressed was a modified Arthrobacter citreus ω-transaminase with improved thermostability. The preparations were compared in terms of cell loading capacity, operational stability in repeated batches and storage stability using the conversion of methylbenzylamine to acetophenone.The use of chitosan for cell immobilization proved to be the method of choice since it was both very simple and effective. At a very high cell loading of 3.2 g cells/g chitosan >60% activity was observed. The preparation was reused in eight successive 1-h batches with >90% remaining activity. To further demonstrate its usability the preparation was used for asymmetric synthesis of (S)-4′-cyano-(α)-methylbenzylamine in three repeated bathes (cycle time >20 h), using isopropylamine as the amine donor. Storage stability was comparable with that of non-immobilized cells. It was concluded that the chitosan method due to its properties and simplicity would be advantageous for use also on a larger scale.     

Optimization and immobilization of amylase obtained from halotolerant bacteria isolated from solar salterns

The objective of the present study was to isolate halotolerant bacteria from the sediment sample collected from Marakanam Solar Salterns, Tamil Nadu, India using NaCl supplemented media and screened for amylase production. Among the 22 isolates recovered, two strains that had immense potential were selected for amylase production and designated as P1 and P2. The phylogenetic analysis revealed that P1 and P2 have highest homology with Pontibacillus chungwhensis (99%) and Bacillus barbaricus (100%). Their amylase activity was optimized to obtain high yield under various temperature, pH and NaCl concentration. P1 and P2 strain showed respective, amylase activity maximum at 35 °C and 40 °C; pH 7.0 and 8.0; 1.5 M and 1.0 M NaCl concentration. Further under optimized conditions, the amylase activity of P1 strain (49.6 U mL^?1) was higher than P2 strain. Therefore, the amylase enzyme isolated from P. chungwhensis P1 was immobilized in sodium alginate beads. Compared to the free enzyme form (49.6 U mL^?1), the immobilized enzyme showed higher amylase activity as 90.3 U mL^?1. The enzyme was further purified partially and the molecular mass was determined as 40 kDa by SDS–PAGE. Thus, high activity of amylase even under increased NaCl concentration would render immense benefits in food processing industries.     

Biodegradability and mechanical properties of polycaprolactone composites encapsulating phosphate-solubilizing bacterium Bacillus sp. PG01

This study examined the feasibility of using polycaprolactone (PCL) and its composites (with starch and/or clay) in encapsulating cells of phosphate-solubilizing bacteria (PSB) for the development of biodegradable and “controlled-release” bacterial fertilizer. The PSB used in this work was an indigenous Bacillus sp. PG01 isolate. The results show that the PG01 strain was able to degrade all the cell-loaded capsules made of PCL and PCL composites, resulting in a continual cell release. Morphology observation indicates that severe disruption of the capsule structure occurred after incubation for 15–20 days. The biodegradability of the capsules decreased in the order of PCL/starch (20 wt%) > PCL/starch (20 wt%)/cay (7 wt%) > PCL alone > PCL/clay (7 wt%). Similar trends were also observed for the decrease in tensile strength and elongation at break, suggesting strong connections between biodegradability and the mechanical properties. Addition of starch appeared to enhance the biodegradability of the capsules, whereas the clay-blended composites were less biodegradable. The amount and rate of cell release from cell-encapsulated PCL-based capsules were positively dependent on the biodegradability and on the decrease in the mechanical strength. Nevertheless, the pattern of cell release was quite similar for all types of capsules. The outcome of this work seems to suggest that by proper manipulation of composite compositions, the controlled release of the bacterial fertilizer (i.e., Bacillus sp. PG01 cells) might be achievable.     

Forming nanoparticles of α-amylase and embedding them into solid surfaces

In the current work nanoparticles (NPs) of α-amylase were generated in an aqueous solution using high-intensity ultrasound, and were subsequently immobilized on polyethylene (PE) films, or polycarbonate (PC) plates, or on microscope glass slides. The α-amylase NPs coated on the solid surfaces have been characterized by ESEM, TEM, FTIR, XPS and AFM. The substrates immobilized with α-amylase were used for hydrolyzing soluble potato starch to maltose. The amount of enzyme introduced in the substrates, leaching properties, and the catalytic activity of the immobilized enzyme were compared. The catalytic activity of the amylase deposited on the three solid surfaces was compared to that of the same amount of free enzyme at different pHs and temperatures. α-Amylase coated on PE showed the best catalytic activity in all the examined parameters when compared to native amylase, especially at high temperatures. When immobilized on glass, α-amylase showed better activity than the native enzyme over all pH and temperature values studied. However, the immobilization on PC did not improve the enzyme activity at any pH and any temperature compared to the free amylase. The kinetic parameters, K_m and V_max were also calculated. The amylase coated PE showed the most favorable kinetic parameters (K_m = 5 g L⁻¹ and V_max = 5E−07 mol mL⁻¹ min⁻¹). In contrast, the anchored enzyme-PC exhibited unfavorable kinetic parameters (K_m = 16 g L⁻¹, V_max = 4.2E−07 mol mL⁻¹ min⁻¹). The corresponding values for amylase-glass were K_m = 7 g L⁻¹, V_max = 1.8E−07 mol mL⁻¹ min⁻¹, relative to those obtained for the free enzyme (K_m = 6.6 g L⁻¹, V_max = 3.3E−07 mol mL⁻¹ min⁻¹).     

Glucoamylase production by the marine yeast Aureobasidium pullulans N13d and hydrolysis of potato starch granules by the enzyme

Under the optimal conditions, 10 U/ml of glucoamylase was produced by the marine yeast Aureobasidium pullulans N13d. It was noticed that the crude glucoamylase actively hydrolyzed potato starch granules, but poorly digested raw corn starch and sweet potato starch, resulting in conversion of 68.5, 19 and 22% of them into glucose within 6 h of incubation in the presence of 40 g/l of potato starch granules and 20 U/ml of the crude enzyme. When potato starch granules concentration was increased from 10 to 80 g/l, hydrolysis extent was decreased from 85.6 to 60%, while potato starch granules concentration was increased from 80 to 360 g/l, hydrolysis extent was decreased from 60 to 56%. Ratio of hydrolysis extent of potato starch granules to hydrolysis extent of gelatinized potato starch was 86.0% and the hydrolysis extent of potato starch granules by action of the crude glucoamylase (1.0 U/ml) was 18.5% within 30 min at 60 °C. Only glucose was detected during the hydrolysis, indicating that the crude enzyme could hydrolyze both α-1,4 and α-1,6 linkages of starch molecule in the potato starch.     

Optimization of the immobilization of sweet potato amylase using glutaraldehyde-agarose support. Characterization of the immobilized enzyme

A simplified procedure for the preparation of immobilized beta-amylase using non-purified extract from fresh sweet potato tubers is established in this paper, using differently activated agarose supports. Beta-amylase glutaraldehyde derivative was the preparation with best features, presenting improved temperature and pH stability and activity. The possibility of reusing the amylase was also shown, when this immobilized enzyme was fully active for five cycles of use. However, immobilization decreased enzyme activity to around 15%. This seems to be mainly due to diffusion limitations of the starch inside the pores of the biocatalyst particles. A fifteen-fold increase in the Km was noticed, while the decrease of Vmax was only 30% (10.1 U mg^?1 protein and 7.03 U mg^?1 protein for free and immobilized preparations, respectively).     

Arthrobacter sp. lipase immobilization on magnetic sol–gel composite supports for enantioselectivity improvement

A bacterial lipase from Arthrobacter sp. (ABL: IIIM Jammu, India strain, MTCC No. 5125) has been immobilized on non-magnetic (Type A) and magnetic (Type B) supports derived from copolymerization of 3-aminopropyltriethoxysilane and tetraethylorthosilicate. Immobilized ABL presented 21–34 mg/g protein binding providing 30–75 units/g activity in Type A non-magnetic composites and 24–45 mg/g protein binding providing 35–90 units/g activity with Type B supports containing magnetic particles. Immobilized ABL preparations have shown enhanced stability at pH 5–9 and temperature up to 70 °C whereas free ABL is unstable under these conditions. Improved hydrolytic conversion as well as enantioselectivity were observed with acyl fluoxetine intermediate (ethyl 3-hydroxy-3-phenylpropanoate alkyl acylates) and chiral auxiliaryacyl 1-phenyl ethanol using immobilized ABL derivatives (ee ～99%; 3–4-fold increase in E-values) as compared to ABL enzyme/cells (ee 93–98%). Introduction of magnetic particles in these supports has led to easier separation process with high product recovery yields.     

Evaluation of a two-stage in vitro technique for estimating digestibility of equine feeds using horse faeces as the source of microbial inoculum

To develop a two-stage in vitro technique that simulates both pre-caecal and hind gut digestion processes, four enzymatic pre-digestion treatments by pepsin and α-amylase (ET0 = control, ET1 = 2 h pepsin + 2 h amylase, ET2 = 2 h pepsin + 4 h amylase, ET3 = 8 h pepsin + 16 h amylase) were tested on oat hay (OH), barley grain (BG) and soybean meal (SBM). Investigated parameters were enzymatic organic matter digestibility (OMDe), and gas production (G48h, G72h) and OM digestibility (OMD) using horse faeces as a source of microbial inoculum.Enzymatic pre-digestion treatments affected (P<0.05) investigated parameters and their ranking differed among feeds. Only OMD of BG and SBM were higher after the pre-digestion treatment. OMD prior to (ET0) and after ET3 application were, successively, 0.357 versus 0.351 (OH), 0.71 versus 0.79 (BG) and 0.70 versus 0.78 (SBM). Net gas production overestimated fermentation potential of non-pre-digested feeds. G72h (ml/g DM) prior to (ET0) and after ET3 application were, successively, 80.3 versus 58.0 (OH), 151.7 versus 30.4 (BG) and 110.6 versus 37.7 (SBM).It was concluded that the enzymatic pre-digestion treatments effects varied among tested feeds, and that the suggested procedure be extended and validated with a large array of feeds of known digestibility values.     

Parameter’s optimization and kinetics study of α-amylase enzyme of Bacillus sp. MB6 isolated from vegetable waste

α-Amylase, a very critical enzyme for hydrolysis of starch into simple sugar and it has various applications in industrial settings. This study reports the identification of Bacillus sp. MB6 which produces increased amount of enzyme from less required resources. To optimize the yield of enzyme, we used various combinations of parameters. The most optimized conditions for production of amylase enzyme from the bacterium Bacillus sp. MB6 are pH of 6, temperature of 37 °C, and incubation period of 48 h. Condition of enzymatic activity were also examined and the results show that pH of 6, a temperature of 55 °C, and a reaction time of 30 min are the best available conditions for its activity. Purification of enzyme by 1.63 fold enhanced the specific activity of enzyme based upon its activity analysis as compared with unpurified enzyme. Enzyme kinetics studies show the Michaelis constant (Km) to be 5.45 mg/ml and maximum velocity of the reaction (Vmax) to be 24.15 mg/ml/min. In conclusion, we report enzyme production and purification methodology that exhibit better yield of alpha-amylase for commercial applications.     

Effect of sucrose on dynamic mechanical characteristics of maize and potato starch films

The dynamic mechanical properties of prepared maize and potato starch films were evaluated for mixtures containing 0%, 10% and 15% (w/w) of sucrose at temperatures ranging from 40.0 to 140.0 °C. The spectra of storage modulus (G′), loss modulus (G″), and loss factor (tan δ) of starch films were acquired. Remarkable reduction in the glass transition temperature of maize and potato starch films was observed with the increasing sucrose content. The spectra of storage modulus (G′), loss modulus (G″), and loss factor (tan δ) were measured for the second and third time after two and seven days, respectively. The peaks of loss factor (tan δ) appeared at 59.81 ± 1.86 °C and 95.96 ± 1.67 °C after two-day-storage, but only one peak appeared at 85.46 ± 5.50 °C after seven days. A shifting trend from higher to lower temperature for loss factor was observed after seven days.