Anaerobic thermophilic digestion of cutting oil wastewater: Effect of co-substrate

This paper describes the thermophilic (55 °C) anaerobic biodegradation of a mixed feed composed of vinasses and cutting oil wastewater (COW) in a laboratory upflow anaerobic fixed-film reactor (UAFF) with a porous support medium. The experimental protocol was defined to examine the effect of increasing the percentage of cutting oil wastewater in the feed.The UAFF reactor was initially started-up with vinasses as the only carbon source at an organic loading rate of 22.3 kg COD/m³ day and HRT of 0.8 days using porous particles as the support (SIRAN). The percentage of organic matter composed of vinasses was subsequently reduced while increasing the amount of cutting oil until 100% of cutting oil wastewater was added in the feed. Four stages were considered in the study (0, 42.4, 66.6 and 100% COW). HRT was adjusted in order to maintain an approximately constant organic loading rate applied to the system. Under theses conditions, the UAFF reactor was subjected to a programme of steady-state operation with hydraulic retention times (HRT) in the range 0.8–0.15 days and organic loading rates (OLR) between 22.3 and 14.9 kg COD/m³ day in order to evaluate the treatment capacity of the system.The COD removal efficiency was found to be 87% COD and 94.6% TOC in the reactor when treating vinasses at 22.3 kg COD/m³ day. The volumetric methane level produced in the digester reached 0.45 m³/m³ day. After an operating period of 120 days, the reactor was fed with cutting oil wastewater (COW) as the only source of carbon. An OLR of 16.7 kg COD/m³ day was achieved with 85.8% COD removal efficiency (58.1%TOC) in the experimental UAFF reactor. Under these conditions the volumetric methane produced in the digester was negligible.Hence, COW can be removed, if not degraded, by anaerobic treatment in the presence of a biodegradable co-substrate. Wine vinasses degradation creates conditions for non-biological removal of COW constituents. More studies are necessary in order to test the mechanisms of organic removal when biodegradation apparently had ceased. Also, toxicity assays of COW are necessary to evaluate the toxicity to the methanogenic community.     

Investigation on the formation and kinetics of glucose-fed aerobic granular sludge

Aerobic granular sludge was cultivated in a glass sequencing batch reactor (SBR) with glucose synthetic wastewater. The spherical shaped granules were observed on 4th day with the mean diameter of 0.1 mm. With the increase of chemical oxygen demand (COD) concentration of the influent, aerobic granules grew matured, the size of which ranged from 1.2 to 1.9 mm. The aerobic granular sludge could sustain high organic loading rate (about 4.0 g COD L⁻¹ d⁻¹), with good settling ability (settling velocity 36 m/h) and high biomass concentration (MLSS 6.7 ±0.2 g/L). Experimental data indicated that the substrate utilization and biomass growth kinetics followed Monod's kinetics model approximately. The corresponding kinetic coefficients of maximum specific substrate utilization rate (k), half velocity coefficient (K_s), growth yield coefficient (Y) and decay coefficient (K_d) were 13.2 d⁻¹, 275.8 mg/L, 0.183–0.250 mg MLSS/mg COD and 0.023–0.075 d⁻¹, respectively, which made aerobic granules have short setup period, high rate of substrate utilization and little surplus sludge.     

Anammox for ammonia removal from pig manure effluents: Effect of organic matter content on process performance

The anammox process, under different organic loading rates (COD), was evaluated using a semi-continuous UASB reactor at 37 °C. Three different substrates were used: initially, synthetic wastewater, and later, two different pig manure effluents (after UASB-post-digestion and after partial oxidation) diluted with synthetic wastewater. High ammonium removal was achieved, up to 92.1 ± 4.9% for diluted UASB-post-digested effluent (95 mg COD L^?1) and up to 98.5 ± 0.8% for diluted partially oxidized effluent (121 mg COD L^?1). Mass balance clearly showed that an increase in organic loading (from 95 mg COD L^?1 to 237 mg COD L^?1 and from 121 mg COD L^?1 to 290 mg COD L^?1 for the UASB-post-digested effluent and the partially oxidized effluent, respectively) negatively affected the anammox process and facilitated heterotrophic denitrification. Partial oxidation as a pre-treatment method improved ammonium removal at high organic matter concentration. Up to threshold organic load concentration of 142 mg COD L^?1 of UASB-post-digested effluent and 242 mg COD L^?1 of partially oxidized effluent, no effect of organic loading on ammonia removal was registered (ammonium removal was above 80%). However, COD concentrations above 237 mg L^?1 (loading rate of 112 mg COD L^?1 day^?1) for post-digested effluent and above 290 mg L^?1 (loading rate of 136 mg COD L^?1 day^?1) for partially oxidized effluent resulted in complete cease of ammonium removal. Results obtained showed that, denitrification and anammox process were simultaneously occurring in the reactor. Denitrification became the dominant ammonium removal process when the COD loading was increased.     

Thermophilic treatment of bulk drug pharmaceutical industrial wastewaters by using hybrid up flow anaerobic sludge blanket reactor

The hybrid up flow anaerobic sludge blanket reactor was evaluated for efficacy in reduction of chemical oxygen demand (COD) and biochemical oxygen demand (BOD) of bulk drug pharmaceutical wastewater under different operational conditions. The start-up of the reactor feed came entirely with glucose, applied at an organic loading rate (OLR) 1 kg COD/m³ d. Then the reactor was studied at different OLRs ranging from 2 to 11 kg COD/m³ d with pharmaceutical wastewater. The optimum OLR was found to be 9 kg COD/m³ d, where we found 65–75% COD and 80–94% of BOD reduction with biogas production containing 60–70% of methane and specific methanogenic activity was 320 ml CH₄/g-VSS d. By the characterization studies of effluent using GC–MS, the hazardous compounds like phenol, l,2-methoxy phenol, 2,4,6-trichloro phenol, dibutyl phthalate, 1-bromo naphthalene, carbamazepine and antipyrine were present. After the treatment, these compounds degraded almost completely except carbamazepine. Thermophilic methanothrix and methanosaetae like bacteria are present in the granular sludge.     

An integrated treatment system for coffee processing wastewater using anaerobic and aerobic process

The experiment was conducted to develop an integrated treatment system for coffee processing wastewater (CPWW) through the combination of biomethanation with aeration and wetland plants treatment. The biomethanation was carried out at different hydraulic retention times (HRTs) using upflow anaerobic hybrid reactor (UAHR) and 18 h of HRT was found to be optimum. The maximum biochemical oxygen demand (BOD), chemical oxygen demand (COD) and total solids (TS) reduction were 66.0%, 61.0% and 58.0%, respectively with organic loading rate of 9.55 kg m^?3 day^?1. The reduction of pollution load of the wastewater by microbial action augmented by aeration resulted in the reduction of electrical conductivity (EC), BOD, COD, and total solids (TS). Continuous aeration of wastewater resulted in maximum reduction of BOD (74.6%), COD (68.6%) and TS (49.3%). The wetland plant, Typha latifolia reduced 85.4% and 78.0% of BOD and COD, respectively in biomethanated cum aerated CPWW.     

A key cultivation technology for denitrifying granular sludge

Well-formed denitrifying granular sludge with a biomass concentration of 24.8 gVSS L^?1 and a specific nitrate removal rate of 0.19 gNO₃-N gVSS^?1 d^?1 was obtained in an upflow sludge blanket (USB) reactor by cultivating seeded aerobic flocculent sludge for 6–8 weeks. Regularity phenomena exist in the granulation including flotation of flocculent sludge, formation of fine granules, occurrence of channelling, and formation of mature granular sludge. The granulation is similar to crystal growth, that the non-denitrifying bacteria evolve into the carriers (fine granules), on the surface of which denitrifying bacteria proliferate and develop into mature granular sludge.There are several key parameters that must be considered when developing a good denitrifying granular sludge. First, the proper seed sludge must be chosen (VSS/SS at 0.65–0.75, SRT over 25 days) to accelerate the granulation process. Secondly, any floating sludge should be stirred, and the sludge loading rate should be within the range of 0.05–0.15 gNO₃-N gVSS^?1 d^?1 until fine granules emerge. Additionally, spontaneous gas agitation or interval air-blowing should be used to effectively eliminate channelling; Finally, the sludge loading rate should be less than 0.25 gNO₃-N gVSS^?1 d^?1 until dense, mature granular sludge appears. This study could support and promote the full-scale application of denitrifying granular sludge.     

Characterization of aerobic granular sludge at various organic loading rates

Aerobic granular sludge was cultivated from activated sludge with two types of supports, namely bivalve shell carrier (BSC) and anaerobic granules (ANG). Granules were characterized at different organic loading rates (OLRs) ranging from 2.5 to 15 kg COD/m³ d and these granules were observed to withstand high OLRs. The physico-chemical characteristics of the aerobic granules were better than those of seed sludge. The granule formation with ANG support was found to be similar to that of non-support cultivation, i.e. formation from activated sludge only. By contrast, BSC support showed better performance in terms of faster settleability, compactness and especially resistance against organic shock loading. It also enabled self-cleaning effect by removing biofilm attached on the reactor wall during the start-up phase resulting rapid granulation process.     

Treatment of high-strength wastewater in tropical constructed wetlands planted with Sesbania sesban: Horizontal subsurface flow versus vertical downflow

Treatment of various types of wastewaters is an urgent problem in densely populated areas of many tropical countries. We studied the potential of using Sesbania sesban, an N₂-fixing shrub, in constructed wetland systems for the treatment of high-strength wastewater. A replicated horizontal subsurface flow system and a saturated vertical downflow system was established with planted and unplanted beds to assess the effects of system design and presence of plants on treatment performance. The systems were loaded with a mixture of domestic and pig farm wastewater at three hydraulic loading rates of 80, 160 and 320 mm d^?1. The S. sesban plants grew very well in the constructed wetland systems and produced 17.2–20.2 kg dry matter m^?2 year^?1 with a high nitrogen content. Mass removal rates and removal rate constants increased with loading rate, but at 320 mm d^?1 the effluent quality was unacceptable and hydraulic problems appeared. Mass removal rates and removal rate constants were much higher than reported in other studies probably because of the high-strength wastewater, the high loading rates and the tropical conditions. Planted systems removed pollutants much more efficiently than the unplanted controls. Direct plant uptake constituted only up to 8% of the total-N removal and 2% of the P removal at the lowest loading rate, and was quantitatively of low importance compared to other removal processes. The significant effects of plants were therefore related more to their indirect effects on the removal processes. This study for the first time documents that S. sesban can be used in constructed wetland systems for the treatment of polluted water while at the same time producing a valuable N rich biomass that can be used for animal fodder or soil amendment.     

Performance of a composite membrane bioreactor treating toluene vapors: Inocula selection,reactor performance and behavior under transient conditions

In this study, a membrane biofilm reactor performance for toluene as a model pollutant is presented. A composite membrane consisting of a porous polyacrylonitrile (PAN) support layer coated with a very thin (0.3 μm) dense polydimethylsiloxane (PDMS) top layer was used. Batch experiments were performed to select an appropriate inocula (slaughterhouse wastewater treatment sludge with a specific toluene consumption rate of 118 ± 23 μg g^?1 VSS L^?1) among the three available sources of inoculums. The maximum elimination capacity gas-side reactor volume based (EC)_v and membrane based (EC)_{m, max} obtained were 609 g m^?3 h^?1 and 1.2 g m^?2 h^?1 respectively, which is much higher than other membrane bioreactors. Further experiments involved the study of the membrane biofilm reactor flexibility when operational parameters as temperature, loading rate etc. were modified. In all cases, the membrane biofilm reactor showed a rapid adaptation and new steady-states were obtained within hours. Overall, the results illustrate that membrane bioreactors can potentially be a good option for treatment of air pollutants such as toluene.     

Investigation on the properties and kinetics of glucose-fed aerobic granular sludge

Aerobic granulation is a process in which suspended biomass aggregate and form discrete well-defined granules in aerobic systems. To investigate the properties and kinetics of aerobic granular sludge, aerobic granules were cultivated with glucose synthetic wastewater in a series of sequencing batch reactors (SBR). The spherical shaped granules were observed on 8th day with the mean diameter of 0.1 mm. With the organic loading rate (OLR) being increased to 4.0 g COD L⁻¹ d⁻¹, aerobic granules grew matured with spherical shape. The size of granules ranged from 1.2 to 1.8 mm, and the corresponding settling velocity of individual granule was 24.2–36.4 m h⁻¹. The oxygen utilization rate (OUR) of mature granules was 41.90 g O₂ kg MLSS⁻¹ h⁻¹, which was two times higher than that of activated sludge (18.32 g O₂ kg MLSS⁻¹ h⁻¹). The experimental data indicated that the substrate utilization and biomass growth kinetics generally followed Monod's kinetics model. The corresponding kinetic coefficients of k (maximum specific substrate utilization rate), K_s (half velocity coefficient), Y (growth yield coefficient) and K_d (decay coefficient) were determined as follows, k_c = 23.65 d⁻¹, K_c = 3367.05 mg L⁻¹, K_N = 0.038 d⁻¹, K_N = 29.65 mg L⁻¹, Y = 0.1927–0.2022 mg MMLS (mg COD)⁻¹ and K_d = 0.00845–0.0135 d⁻¹, respectively. Those properties of aerobic granules made aerobic granules system had a short setup period, high substrate utilization rate and low sludge production.     

Treatment of high-strength wastewater in tropical vertical flow constructed wetlands planted with Typha angustifolia and Cyperus involucratus

The ability of vertical flow (VF) constructed wetland systems to treat high-strength (ca. 300 mg L^?1 of COD and ca. 300 mg L^?1 total-nitrogen) wastewater under tropical climatic conditions was studied during a 5-month period. Nine 0.8-m diameter experimental VF units (depth 0.6 m) were used: three units were planted with Typha angustifolia L., another three units were planted with Cyperus involucratus Rottb and three units were unplanted. Each set of units were operated at hydraulic loading rates (HLRs) of 20, 50 and 80 mm d^?1. Cyperus produced more shoots and biomass than the Typha, which was probably stressed because of lack of water. The high evapotranspirative water loss from the Cyperus systems resulted in higher effluent concentrations of COD and total-P, but the mass removal of COD did not differ significantly between planted and unplanted systems. Average mass removal rates of COD, TKN and total-P at a HLR of 80 mm d^?1 were 17.8, 15.4 and 0.69 g m^?2 d^?1. The first-order removal rate constants at a HLR of 80 mm d^?1 for COD, TKN and total-P were 49.8, 30.1 and 13.5 m year^?1, respectively, which is in the higher range of k-values reported in the literature. The oxygen transfer rates were ca. 80 g m^?2 d^?1 in the planted systems as opposed to ca. 60 g m^?2 d^?1 in the unplanted systems. The number of Nitrosomonas was two to three orders of magnitude higher in the planted systems compared to the unplanted systems. Planted systems thus had significantly higher removal rates of nitrogen and phosphorus, higher oxygen transfer rates, and higher quantities of ammonia-oxidizing bacteria. None of the systems did, however, fully nitrify the wastewater, even at low loading rates. The vertical filters did not provide sufficient contact time between the wastewater and the biofilm on the gravel medium of the filters probably because of the shallow bed depth (0.6 m) and the coarse texture of the gravel. It is concluded that vertical flow constructed wetland systems have a high capacity to treat high-strength wastewater in tropical climates. The gravel and sand matrix of the vertical filter must, however, be designed in a way so that the pulse-loaded wastewater can pass through the filter medium at a speed that will allow the water to drain before the next dose arrives whilst at the same time holding the water back long enough to allow sufficient contact with the biofilm on the filter medium.     

Treatment of domestic wastewater in tropical,subsurface flow constructed wetlands planted with Canna and Heliconia

Constructed wetlands have a good potential for wastewater treatment in developing countries due to the simple operation and low implementation costs. Ornamental plants like Canna and Heliconia are used in the wetlands to increase their aesthetic value and these two species were compared in this study. Six pilot scale horizontal subsurface flow constructed wetland units were constructed at the Asian Institute of Technology (AIT) campus in Bangkok, Thailand, of which three were planted with Heliconia psittacorum L.f. × H. Spathocircinata (Aristeguieta) and three with Canna × generalis L. Bailey. The beds were loaded with domestic wastewater in four trials with hydraulic loading rates ranging from 55 to 440 mm d^?1 corresponding to nominal detention times between 12 h and 4 days. Both plant species grew well in the systems and especially Canna had high growth rates (3100 ± 470 g DW m^?2 yr^?1) compared to Heliconia (550 ± 90 g DW m^?2 yr^?1). TSS mass removal rates were very high with efficiencies >88% even at hydraulic loading rates of 440 mm d^?1. COD mass removal rates varied between 42 and 83% depending on the loading rates. The removal rate constants for COD as fitted by the first-order k–C^* model were estimated to be 0.283 and 0.271 m d^?1 for Canna and Heliconia beds, respectively (C^* = 28.1 and 26.7 mg l^?1). Removals of nitrogen (N) and phosphorus (P) were low compared to the loading rates, but removal of total-N was higher in the beds planted with Canna than in beds with Heliconia because of the higher growth rate of Canna. It is concluded that ornamental species like Canna and Heliconia can be used to enhance the aesthetic appearance and hence the public acceptance of wastewater treatment systems in tropical climates. Canna is the preferred species from a treatment perspective because of its more vigorous growth, but since Heliconia has an economic potential as cut flowers may be preferred in many cases.     

Effect of hydraulic retention time on the treatment of secondary effluent in a subsurface flow constructed wetland

This study evaluates the potential of subsurface flow (SSF) constructed wetlands (CWs) for tertiary treatment of wastewater at four shorter HRTs (1–4 days). The CWs were planted with Typha angustata, which was observed in our earlier study to be more efficient than Phragmites karka and Scirpus littoralis. The CWs comprised four rectangular treatment cells (2.14 m × 0.76 m × 0.61 m) filled with layers of gravel of two different sizes (approximately 2.5 cm and 1.5 cm diameter) to a depth of 0.61 m. The inflow rates of the secondary effluent in the four cells were accordingly fixed at 300 L d^?1, 150 L d^?1, 100 L d^?1 and 75 L d^?1, respectively, for 1, 2, 3 and 4 days HRT. The hydraulic loads ranged between 59.05 mm d^?1 and 236.22 mm d^?1.The wastewater inflow into the CW system as well as the treated effluent were analyzed, using standard methods, at regular intervals for various forms of nitrogen (NH₄-N, NO₃-N and TKN), orthophosphate-P and organic matter (BOD and COD) concentrations over a period of five weeks after the development of a dense stand.The higher HRT of 4 days not only helped maximum removal of all the pollutants but also maintained the stability of the treatment efficiency throughout the monitoring period. For the nutrients (NH₄-N, NO₃-N and TKN), HRT played a more significant role in their removal than in case of organic matter (BOD₃ and COD). More than 90% of NO₃-N and TKN and 100% of NH₄-N were removed from the wastewater at 4 days HRT.At lower HRTs, the mass loading rate was higher with greater fluctuation. However mass reduction efficiency of the T. angustata CW for all forms of nitrogen was >80% with the HRTs of 2, 3 and 4 days.     

Anaerobic submerged membrane bioreactor (AnSMBR) treating low-strength wastewater under psychrophilic temperature conditions

An anaerobic submerged membrane bioreactor (AnSMBR) treating low-strength wastewater was operated for 90 days under psychrophilic temperature conditions (20 °C). Besides biogas sparging, additional shear was created by circulating sludge to control membrane fouling. The critical flux concept was used to evaluate the effectiveness of this configuration. Biogas sparging with a gas velocity (U_G) of 62 m/h together with sludge circulation (94 m/h) led to a critical flux of 7 L/(m² h). Nevertheless, a further increase in the U_G only minimally enhanced the critical flux. A low fouling rate was observed under critical flux conditions. The cake layer represented the main fouling resistance after 85 days of operation. Distinctly different volatile fatty acid (VFA) concentrations in the reactor and in the permeate were always observed. This fact suggests that a biologically active part of the cake layer contributes to degrade a part of the daily organic load. Hence, chemical oxygen demand (COD) removal efficiencies of up to 94% were observed. Nevertheless, the biogas balance indicates that even considering the dissolved methane, the methane yield were always lower than the theoretical value, which indicates that the organic compounds were not completely degraded but physically retained by the membrane in the reactor.     

Microbial processes and bacterial populations associated to anaerobic treatment of sulfate-rich wastewater

A pilot-scale (1.2 m³) anaerobic sequencing batch biofilm reactor (ASBBR) containing mineral coal for biomass attachment was fed with sulfate-rich wastewater at increasing sulfate concentrations. Ethanol was used as the main organic source. Tested COD/sulfate ratios were of 1.8 and 1.5 for sulfate loading rates of 0.65–1.90 kgSO₄²⁻/cycle (48 h-cycle) or of 1.0 in the trial with 3.0 gSO₄²⁻ l⁻¹. Sulfate removal efficiencies observed in all trials were as high as 99%. Molecular inventories indicated a shift on the microbial composition and a decrease on species diversity with the increase of sulfate concentration. Beta-proteobacteria species affiliated with Aminomonas spp. and Thermanaerovibrio spp. predominated at 1.0 gSO₄²⁻ l⁻¹. At higher sulfate concentrations the predominant bacterial group was Delta-proteobacteria mainly Desulfovibrio spp. and Desulfomicrobium spp. at 2.0 gSO₄²⁻ l⁻¹, whereas Desulfurella spp. and Coprothermobacter spp. predominated at 3.0 gSO₄²⁻ l⁻¹. These organisms have been commonly associated with sulfate reduction producing acetate, sulfide and sulfur. Methanogenic archaea (Methanosaeta spp.) was found at 1.0 and 2.0 gSO₄²⁻ l⁻¹. Additionally, a simplified mathematical model was used to infer on metabolic pathways of the biomass involved in sulfate reduction.     

Fermentative production of succinic acid from straw hydrolysate by Actinobacillus succinogenes

In this work, straw hydrolysates were used to produce succinic acid by Actinobacillus succinogenes CGMCC1593 for the first time. Results indicated that both glucose and xylose in the straw hydrolysates were utilized in succinic acid production, and the hydrolysates of corn straw was better than that of rice or wheat straw in anaerobic fermentation of succinic acid. However, cell growth and succinic acid production were inhibited when the initial concentration of sugar, which was from corn straw hydrolysate (CSH), was higher than 60 g l^?1. In batch fermentation, 45.5 g l^?1 succinic acid concentration and 80.7% yield were attained after 48 h incubation with 58 g l^?1 of initial sugar from corn straw hydrolysate in a 5-l stirred bioreactor. While in fed-batch fermentation, concentration of succinic acid achieved 53.2 g l^?1 at a rate of 1.21 g l^?1 h^?1 after 44 h of fermentation. Our work suggested that corn straw could be utilized for the economical production of succinic acid by A. succinogenes.     

Effects of nitrobenzene concentration and hydraulic retention time on the treatment of nitrobenzene in sequential anaerobic baffled reactor (ABR)/continuously stirred tank reactor (CSTR) system

The effects of increasing nitrobenzene (NB) concentrations and hydraulic retention times (HRT) on the treatment of NB were investigated in a sequential anaerobic baffled reactor (ABR)/aerobic completely stirred tank reactor (CSTR) system. In the first step of the study, the maximum COD removal efficiencies were found as 88% and 92% at NB concentrations varying between 30 mg L^?1 and 210 mg L^?1 in ABR. The minimum COD removal efficiency was 79% at a NB concentration of 700 mg L^?1. The removal efficiency of NB was nearly 100% for all NB concentrations in the ABR reactor. The methane gas production and the methane gas percentage remained stable (1500 mL day^?1 and 48–50%, respectively) as the NB concentration was increased from 30 to 210 mg L^?1. In the second step of the study it was found that as the HRT decreased from 10.38 days to 2.5 days the COD removal efficiencies decreased slightly from 94% to 92% in the ABR. For maximum COD and NB removal efficiencies the optimum HRT was found as 2.5 days in the ABR. The total COD removal efficiency was 95% in sequential anaerobic (ABR)/aerobic (CSTR) reactor system at a minimum HRT of 1 day. When the HRT was decreased from 10.38 days to 1 day, the methane percentage decreased from 42% to 29% in an ABR reactor treating 100 mg L^?1 NB. Nitrobenzene was reduced to aniline under anaerobic conditions while aniline was mineralized to catechol with meta cleavage under aerobic conditions.     

Aerobic granulation in sequencing batch reactors with different reactor height/diameter ratios

Effects of reactor height/diameter ratios ranged from 24 to 4 corresponding to reactor settling velocities from 12 to 2 m h^?1 on aerobic granulation were investigated. It was found that granules appeared after 1-week operation and granule volume percentages exceeded 50% after 2–3 weeks in four reactors. In addition, similar granule fraction of 94–96% was found at steady state in all four reactors. Sludge volume index (SVI), average sludge size, biomass density and granule settling velocity at steady state were around 50 ml g^?1, 1800 μm, 53 g l^?1 and 40 m h^?1, respectively, in four reactors. Extracellular polymeric substances (EPS) and specific oxygen uptake rate (SOUR) were around 38 mg g^?1 VSS and 40 mg O₂ g^?1 VSS h^?1, respectively. Denaturing gradient gel electrophoresis (DGGE) fingerprint of sludge in four reactors showed the same microbial population shift during the start-up period and same microbial community structure during steady-state period. These results recommended strongly that reactor height/diameter ratio or reactor setting velocity in the used range in this study did not affect granule formation, physical characteristics, microbial community structure of granules and stable operation of granular sludge reactor. Reactor height/diameter ratio thus can be very flexible in the practice, which is important for the application of aerobic granule technology.     

Impacts of monosodium glutamate industrial wastewater on plant growth and soil characteristics

Research into utilization of monosodium glutamate industrial wastewater (MSGW) as a plant nutrient source was undertaken. The physico-chemical and microbiological characteristics of MSGW were analyzed in detail. Effect of MSGW on early growth of Chinese cabbage (Brassica rapa L. cv. Pekinensis) and maize (Zea mays L. cv. Bright Jean) was tested by the seed germination bioassay. Subsequently, in a greenhouse pot experiment using the same plant species, effects of MSGW application rates on the plant biomass yield, nitrogen content and soil properties were analyzed. The MSGW was characterized by high levels of N (56.7 g l^?1), organic C (344.6 g l^?1), total solids (600 g l^?1) and other minerals. At MSGW concentrations below 1%, germination indices for both the plant species were significantly (p < 0.01) higher than the control. Further, the greenhouse study results indicated significant increase in the plant biomass yield at MSGW application rates of 5000 and 7500 l ha^?1. As the MSGW dose increased, the biomass yield decreased, decreasing the N-use efficiency. Maize showed significantly higher wastewater N-use efficiency compared to the Chinese cabbage. Although the total culturable bacterial and fungal counts in the raw MSGW were low, addition of MSGW to the soil increased the soil microbial activities and soil respiration. Soil organic C was also increased by the addition of MSGW, due to the presence of significant amounts of organic C in the wastewater. This preliminary study demonstrates that by proper management of the pH and optimization of application rate, MSGW can be utilized as a nutrient source for plant growth. Further long-term field studies to evaluate the environmental impact of MSGW usage in agriculture are being designed to reduce the environmental risks associated with the reuse of this underutilized wastewater in the agriculture.     

Removal of nutrients from wastewater with Canna indica L. under different vertical-flow constructed wetland conditions

Constructed wetlands are becoming increasingly popular worldwide for removing contaminants from domestic wastewater. This study investigated the removal efficiency of nitrogen (N) and phosphorus (P) from wastewater with the simulated vertical-flow constructed wetlands (VFCWs) under three different substrates (i.e., BFAS or blast furnace artificial slag, CBAS or coal burn artificial slag, and MSAS or midsized sand artificial slag), hydraulic loading rates (i.e., 7, 14, and 21 cm d^?1), and wetland operational periods (0.5, 1, and 2 years) as well as with and without planting Canna indica L. The wastewater was collected from the campus of South China Agricultural University, Guangzhou, China. Results show that the percent removal of total P (TP) and ammonium N (NH₄⁺-N) by the substrates was BFAS > CBAS > MSAS due to the high contents of Ca and Al in substrate BFAS. In contrast, the percent removal of total N (TN) by the substrates was CBAS > MSAS > BFAS due to the complicated nitrification/denitrification processes. The percent removal of nutrients by all of the substrates was TP > NH₄⁺-N > TN. About 10% more TN was removed from the wastewater after planting Canna indica L. A lower hydraulic loading rate or longer hydraulic retention time (HRT) resulted in a higher removal of TP, NH₄⁺-N, and TN because of more contacts and interactions among nutrients, substrates, and roots under the longer HRT. Removal of NO₃^?N from the simulated VFCWs is a complex process. A high concentration of NO₃^?N in the effluent was observed under the high hydraulic loading rate because more NH₄⁺-N and oxygen were available for nitrification and a shorter HRT was unfavorable for denitrification. In general, a longer operational period had a highest removal rate for nutrients in the VFCWs.