Physiological aspects of l-lysine production: effect of nutritional limitations on a producing strain of Corynebacterium glutamicum

The effect of nutritional limitations, such as phosphorus and carbon, on the production of l-lysine by Corynebacterium glutamicum was studied in continuous culture. We observed that phosphate-limited cultures at low growth rates were favourable to l-lysine production. l-Lysine was produced when a culture at low dilution rate (0.03 h^–1) was established. A dilution rate of about 0.04 h^–1 should be maintained in order to assure good productivity and an l-lysine yield of 0.53 g/g. Under carbon-limiting conditions the maintenance energy and growth yield of 0.03 g/g·g^–1·h^–1 and 0.41 g/g, respectively, have been obtained. Under these limiting conditions the l-lysine production was not favoured even at lower dilution rates.Correspondence to: N. Coello     

Metabolic and kinetic studies of hybridomas in exponentially fed-batch cultures using T-flasks

Exponentially fed-batch cultures (EFBC) of a murine hybridoma in T-flasks were explored as a simple alternative experimental tool to chemostats for the study of metabolism, growth and monoclonal antibody (MAb) production kinetics. EFBC were operated in the variable volume mode using an exponentially increasing and predetermined stepwise feeding profile of fresh complete medium. The dynamic and steady-state behaviors of the EFBC coincided with those reported for chemostats at dilution rates below the maximum growth rate. In particular, steady-state for growth rate and concentration of viable cells, glucose, and lactate was attained at different dilution rates between 0.005 and 0.05 h^–1. For such a range, the glucose and lactate metabolic quotients and the steady-state glucose concentration increased, whereas total MAb, volumetric, and specific MAb production rates decreased 65-, 6-, and 3-fold, respectively, with increasing dilution rates. The lactate from glucose yield remained relatively constant for dilution rates up to 0.03 h^–1, where it started to decrease. In contrast, viability remained above 80% at high dilution rates but rapidly decreased at dilution rates below 0.02 h^–1. No true washout occurred during operation above the maximum growth, as concluded from the constant viable cell number. However, growth rate decreased to as low as 0.01 h^–1, suggesting the requirement of a minimum cell density, and concomitant autocrine growth factors, for growth. Chemostat operation drawbacks were avoided by EFBC in T-flasks. Namely, simple and stable operation was obtained at dilution rates ranging from very low to above the maximum growth rate. Furthermore, simultaneous operation of multiple experiments in reduced size was possible, minimizing start-up time, media and equipment costs.Abbreviations EFBC exponentially-fed batch culture - CSC continuous suspended culture - MAb monoclonal antibody - D dilution rate - q _i metabolic quotient or specific rate of consumption or production of i     

Lactic acid productivity of a continuous culture of Lactobacillus delbreuckii

Summary Maximum volumetric productivities of biomass (1.40 gl^–1h^–1) and lactic acid (8.93 gl^–1h^–1) for a continuous culture ofLactobacillus delbreuckii occurred between dilution rates 0.35h^–1 and 0.40h^–1. All major nutrients were in excess in these cultures. Glucose utilisation was complete at dilution rates of 0.1h^–1 and lower. Product and biomass yields were constant in the dilution rate range studied (0.05h^–1 to 0.50h^–1).     

Biofilm build-up of Pseudomonas putida in a chemostat at different dilution rates

Summary A test system was set up where the build-up of a biofilm on a defined surface could be studied in a carbon source limited chemostat.The attachment of P. putida ATCC 11172 to glass when growing on L-asparagine was studied at different dilution rates (specific growth rates) from 0.1 to 1.5 h^–1 The number of attached colony forming units (cfu) increased with dilution rate from 1×10⁶ cfu/cm² at 0.1 h^–1 to 4×10⁷ cfu/cm² at 1.0 h^–1 and then the attachment decreased to about 6×10⁶ cfu/cm² at higher dilution rates (1.1–1.5 h^–1). The number of attached cfu was measured after 24 h exposure. The value of the maximum specific growth rate in batch culture was 0.6 h^–1.The total amount of attached cell-mass followed roughly the same pattern as the viable count.The viable count of the cells suspended in the growth medium showed its lowest value at the same dilution rate as resulted in maximum adhesion.It was shown that the effect of growth rate on the biofilm build-up of P. putida is significant, and ought to be borne in mind when continuous culture systems are set up and results evaluated.     

Production of xanthan by in-flow cultures of Xanthomonas campestris

The kinetics of xanthan formation in Xanthomonas campestris continuous and fed-batch fermentations was studied along with metabolic changes due to growth rate variation. A maximum growth rate within the range 0.11–0.12 h^–1 was obtained from the continuous culture data in defined medium, producing xanthan at rates up to 0.36 g l^–1 h^–1 corresponding to a maximum 67% glucose conversion at a dilution rate (D) of 0.05 h^–1. Comparatively, fed-batch cultivation was more efficient, producing maximum xanthan at 0.75 g l^–1 h^–1 and 63% glucose conversion at 0.1 h^–1. When reaching D=0.062 h^–1 in continuous cultures, a change was observed and the values of the specific rate of substrate consumption shifted, initiating an uncoupled growth region expressing a lack of balance of the catabolic and anabolic reactions. The deviation was not accompanied by a change in specific xanthan production indicating that xanthan metabolism was not affected by D. For fed-batch-grown X. campestris cells within the range D=0.03–0.1 h^–1, both metabolic parameters changed linearly with the growth rate showing a wide region coupled to growth. Outside that range, glucose accumulated and the specific xanthan production dropped, suggesting substrate inhibition. Correspondence to: J. C. Roseiro     

Continuous solvent production by Clostridium beijerinckii BA101 immobilized by adsorption onto brick

The performance of a continuous bioreactor containing Clostridium beijerinckii BA101 adsorbed onto clay brick was examined for the fermentation of acetone, butanol, and ethanol (ABE). Dilution rates from 0.3 to 2.5 h^–1 were investigated with the highest solvent productivity of 15.8 g l^–1 h^–1 being obtained at 2.0 h^–1. The solvent yield at this dilution rate was found to be 0.38 g g^–1 and total solvent concentration was 7.9 g l^–1. The solvent yield was maximum at 0.45 at a dilution rate of 0.3 h^–1. The maximum solvent productivity obtained was found to be 2.5 times greater than most other immobilized continuous and cell recycle systems previously reported for ABE fermentation. A higher dilution rate (above 2.0 h^–1) resulted in acid production rather than solvent production. This reactor was found to be stable for over 550 h. Scanning electron micrographs (SEM) demonstrated that a large amount of C. beijerinckii cells were adsorbed onto the brick support.     

Effect of culture conditions on astaxanthin production by a mutant of Phaffia rhodozyma in batch and chemostat culture

Temperature and pH had only a slight effect on the astaxanthin content of a Phaffia rhodozyma mutant, but influenced the maximum specific growth rate and cell yield profoundly. The optimum conditions for astaxanthin production were 22°C at pH 5.0 with a low concentration of carbon source. Astaxanthin production was growth-associated, and the volumetric astaxanthin concentration gradually decreased after depletion of the carbon source. The biomass concentration decreased rapidly during the stationary growth phase with a concomitant increase in the cellular content of astaxanthin. Sucrose hydrolysis exceeded the assimilation rates of D-glucose and D-fructose and these sugars accumulated during batch cultivation. D-Glucose initially delayed D-fructose uptake, but D-fructose utilization commenced before glucose depletion. In continuous culture, the highest astaxanthin content was obtained at the lowest dilution rate of 0.043 h^–1. The cell yield reached a maximum of 0.48 g cells·g^–1 glucose utilized between dilution rates of 0.05 h^–1 and 0.07 h^–1 and decreased markedly at higher dilution rates. Correspondence to: J. C. Du Preez     

Ethanol production by immobilized whole cells ofZymomonas mobilis in a continuous flow expanded bed bioreactor and a continuous flow stirred tank bioreactor

Continuous ethanol fermentation by immobilized whole cells ofZymomonas mobilis was investigated in an expanded bed bioreactor and in a continuous stirred tank reactor at glucose concentrations of 100, 150 and 200 g L^–1. The effect of different dilution rates on ethanol production by immobilized whole cells ofZymomonas mobilis was studied in both reactors. The maximum ethanol productivity attained was 21 g L^–1 h^–1 at a dilution rate of 0.36 h^–1 with 150 g glucose L^–1 in the continuous expanded bed bioreactor. The conversion of glucose to ethanol was independent of the glucose concentration in both reactors.     

The influence of H2, CO2 and dilution rate on the continuous fermentation of acetone-butanol

Summary The effect of product gases, H₂ and CO₂, on solvent production was studied using a continuous culture of alginate-immobilized Clostridium acetobutylicum. Initially, in order to find the optimum dilution rate for aceton--butanol production in this system, fermentations were carried out at various dilution rates. With 10% H₂ and 10% CO₂ in the sparging gas, a dilution rate of 0.07 h^–1 was found to maximize volumetric productivity (0.58 g·l^–1·h^–1), while the maximum specific productivity of 0.27 g^–·h^–1 occured at 0.12 h^–1. Continuous cultures with vigorous sparging of N₂ produced only acids. It was concluded that in the case of continuous fermentation H₂ is essential for good solvent production, although good solvent production is possible in an H₂-absent environment in the case of batch fermentations. When the fermentation was carried out at atmospheric pressure under H₂-enriched conditions, the presence of CO₂ in the sparging gas did not slow down glucose metabolism; rather it changed the direction of the phosphoroclastic reaction and as a result increased the butanol/acetone ratio.     

Continuous culture of Candida boidinii variant 60 growing on methanol

Summary A new variant, Candida boidinii variant 60, which is less sensitive to methanol and formaldehyde shocks was grown in continuous cultures with methanol as sole carbon source. The substrate concentration in the feeding medium was either 1% methanol or 3% methanol. Biomass production, methanol consumption, the formation of formaldehyde and gas exchange were measured at different dilution rates. With low methanol feeding (10 g/l) maximal productivity of 0.44 g biomass/l·h is obtained at a dilution rate of 0.14 h^–1. Maximal specific growth rate is 0.18 h^–1. A yield of 0.32 g biomass/g methanol was obtained and the respiration quotient was determined as 0.55. Independently of initial substrate concentration, biomass decreases if methanol and formaldehyde are accumulating in the culture broth.In the culture with high methanol feeding (30 g/l) cell concentratioon increases up to 9 g/l at D=0.04 h^–1. At higher dilution rates methanol and form-aldehyde appear in the medium. Formaldehyde is then preferably oxidized without energy advantages for the cells. It seems that this enables the cells to overcome toxic effects caused by methanol and formaldehyde.     

L-Sorbose production in a continuous fermenter with and without cell recycle

The kinetics of continuous l-sorbose fermentation using Acetobacter suboxydans with and without cell recycle (100%) were investigated at dilution rates (D) of 0.05, 0.10, 0.15 and 0.3 h^–1. The biomass and sorbose concentrations for continuous fermentation without recycle increased as the dilution rate was increased from 0.05 to 0.10 h^–1. A maximum biomass concentration of 8.44 g l^–1 and sorbose concentration of 176.90 g l^–1 were obtained at D=0.10 h^–1. The specific rate of sorbose production and volumetric sorbose productivity at this dilution rate were 2.09 g g^–1 h^–1 and 17.69 g l^–1 h^–1. However, on further increasing the dilution rate to 0.3 h^–1, both biomass and sorbose concentrations decreased to 2.93 and 73.20 g l^–1 respectively, mainly due to washout of the reactor contents. However, the specific rate of sorbose formation and volumetric sorbose productivity at this dilution rate increased to 7.49 g g^–1 h^–1 and 21.96 g l^–1 h^–1 respectively. Continuous fermentation with 100% cell recycle served to further enhance the concentration of biomass and sorbose to 28.27 and 184.32 g l^–1 respectively (in the reactor at a dilution rate of 0.05 h^–1). Even though, there was a decline in the biomass and sorbose concentrations to 6.8 and 83.40 g l^–1 at a dilution rate of 0.3 h^–1, the specific rates of sorbose formation and volumetric sorbose productivity increased to 3.67 g g^–1h^–1 and 25.02 g l^–1 h^–1.     

Two-stage continuous fermentation of Clostridium acetobutylicum: effects of pH and dilution rate

Summary The kinetics of a two-stage continuous fermentation of Clostridium acetobutylicum have been studied. The pH and the dilution rate have been shown to be two essential factors for process optimization. An increase in pH or dilution rate in the first stage decreased solvent production in the second fermentor. To achieve optimal solvent production, the pH had to be maintained at 4.5 in the first stage and between 4.5 and 5.0 in the second stage. Dilution rates of 0.08 h^–1 and 0.04 h^–1,respectively, in the first and second fermentors allowed a high solvent concentration. When the pH was maintained at 4.5 in each stage and when the dilution rates were 0.08 h^–1 and 0.04 h^–1 in the first and second fermentors respectively, 21 g/l solvent concentration was achieved. A conversion yield of 0.36 g solvents/g glucose consumed was obtained with total consumption of glucose. Biomass was only produced in the first stage together with 40% of the solvents, indicating that solvent production had to be induced in the first fermentor. Offprint requests to: J. M. Engasser     

Invertase and phosphatase of yeast in a phosphate-limited continuous culture

Summary Deficiency of inorganic phosphate caused the hyper production of invertase and the derepression of acid phosphatase in a continuous culture ofSaccharomyces carlsbergensis. The specific invertase activity was 40,000 enzyme units per g dry cell weight at a dilution rate lower than 0.05 h^–1 with a synthetic glucose medium of which the molecular ratio of KH₂PO₄ to glucose was less than 0.006. This activity is eight fold higher than in a batch growth and 1.5 fold as much as the highest enzyme activity observed so far in a glucose-limited continuous culture.For the hyper production of invertase, it is necessary to culture the yeast continuously by keeping the Nyholm's conservative inorganic phosphate concentration at less than 0.2 m mole per g dry weight cell. The derepression of acid phosphatase brought about by phosphate deficiency, was similar in both batch and continuous cultures.Nomenclature D dilution rate of continuous culture (h^–1) - E_i invertase concentration in culture (enzyme unit l^–1) - E_p acid phosphatase concentration in culture (enzyme unit l^–1) - P inorganic phosphate concentration in culture (mM) - S glucose concentration in culture (mM) - X cell concentration in culture (g dry weight cell l^–1) Greek Letter specific rate of growth (h^–1) Suffix f feed - 0 initial value     

Degradation of sodium anthraquinone sulphonate by free and immobilized bacterial cultures

Aerobic biodegradation of a xenobiotic recalcitrant compound sodium anthraquinone-2-sulphonate (SAS), was investigated using as an inoculum a mixed microbial culture, which was activated sludge from industrial and domestic waste-water treatment plants. The difference in SAS degradation was examined using two main systems: (1) suspended cells and (2) immobilized cells, both in batch and in continuous culture. In the suspended cell system, under continuous culture conditions using SAS as a unique source of carbon and energy, it was possible to degrade about 95% of this substrate after 6 days. Maximal SAS removal rates in the suspended-cell system were 593 mg SAS l^–1 h^–1 and 88.7 mg SAS l^–1 h^–1 for dilution rates (D) of 0.05 h^–1 and 0.075 h^–1, respectively. In the immobilized-cell system, almost all SAS was degraded in 6 days and the maximal removal rate reached 88.7 mg SAS l^–1 h^–1 at D=0.05 h^–1. Application of a continuous-flow enrichment procedure resulted in selection of several kinds of micro-organisms and led to a progressive elimination of some species of Aeromonas. A stable microbial community of 11 strains has been established and characterized at D=0.075 h^–1. Most of them were Gram-negative and belonged to the genus Pseudomonas.     

Effect of the growth rate on the enzymatic activities of L-lysine-producing cells of Corynebacterium glutamicum

The activity of 6-phosphogluconate dehydrogenase, aspartate kinase and phosphoenolpyruvate carboxylase has been studied at different dilution rates in aerobic continuous culture of Corynebacterium glutamicum. 6-Phosphogluconate dehydrogenase and aspartate kinase reached their maximum values at the lower dilution rates (0.02–0.06 h^–1), when L-lysine was produced. The phosphoenolpyruvate carboxylase activity seemed to be independent of metabolite synthesis. The production of L-lysine was also studied in non-growing cells in batch cultures. In these conditions, statistical analysis revealed significant differences in L-lysine titres when glucose or gluconic acid were used as carbon sources. Higher L-lysine concentration obtained with gluconic acid was found to be associated with a high 6-phosphogluconate dehydrogenase activity.     

Cellulase production by Trichoderma reesei

Summary A model is proposed for the enzyme production by Trichoderma reesei (QM 9414), which assumes control of the active enzyme transport through the cell membrane as a key parameter for the enzyme activity change in the culture filtrate. In a stirred tank reactor, continuous cultivation of the fungus was carried out in the dilution rate range of D=0.01–0.032 h^–1. After changing the dilution rate it took 3–4 weeks to attain a steady state in enzyme activity. Reducing sugars, dissolved protein, enzyme activity (filter-paper and glucosidase activities), cellulose and nitrogen content of the sediment, the elementary analysis of the cell and the composition of the outlet gas were all determined during cultivation. At a dilution rate of D=0.025 h^–1 all of these properties change due to derepression (for D<0.025 h^–1) or repression (for D>0.025 h^–1) of the enzymes which are responsible for the active transport of cellulases from the cell into the medium. The cellulase excretion causes a decrease of the yield coefficient of growth and a reduction of the nitrogen content of the cells.In a two-stage system the time to attain a steady state increases to 4–6 weeks. At low dilution rates the enzyme activity is only slightly higher in the second stage than in the first. At high dilution rates, at which the enzyme is not excreted into the medium in the first stage, enzyme activity can be increased considerably in the second stage.     

The isolation and characterisation of a salicylate-hydroxylase-producing strain of Pseudomonas putida

Summary A salicylate-hydroxylase-producing strain of Pseudomonas putida with an unusual capability to grow at toxic levels of salicylate up to 10 g l^–1 has been isolated. It grew well under continuous culture conditions, with optimum growth at pH 6.5 and a temperature of 25° C. The use of an ammonium salt as a nitrogen source, instead of nitrate, resulted in a 30–40% increase in its biomass yield coefficient. Optimum growth under continuous culture conditions was achieved using 4 g l^–1 salicylate at 25° C, pH 6.5 and 0.2 h^–1 dilution rate. High salicylate hydroxylase enzyme activity [236 units (U) l^–1] and productivity (424.8 U h^–1) were obtained at a dilution rate of 0.45 h^–1 using a mineral medium containing 4 g l^–1 of salicylate. Operating under continuous culture conditions with oxygen limitation and a slight accumulation of residual salicylate (0.2 g l^–1) resulted in a decrease in culture performance and enzyme productivity. Correspondence to: R. Marchant     

Production of thermostable xylanases in batch and continuous culture by Thermomonospora fusca KW 3

Summary The actinomycete Thermomonospora fusca KW 3 produced novel thermostable xylanases in batch and continuous cultures in media containing insoluble xylan. The production of xylanases could be induced with oat spelt or beech xylan. Very low activities were detected when the strain was grown on glucose or xylose. In continuous cultivations, mycelial wall growth could be prevented using a stirrer speed controller. Homogeneous mixing of the insoluble substrate was obtained by vibrating the flexible tubes. T. fusca KW 3 could be grown on insoluble xylan at growth rates as high as 0.23 h^–1, equivalent to a doubling time of 3 h. Xylanase activity decreased from maximum levels of 2.5 units (U) ml^–1 with increasing dilution rate and was nearly constant at a level of 0.5 U ml^–1 with dilution rates greater than 0.1 h^–1. Correspondence to: P. Röthlisberger     

Effect of the dilution rate on the biomass yield ofBacillus thuringiensis and determination of its rate coefficients under steady-state conditions

Depending on the biomass yield on glucose and the cell morphology ofBacillus thuringiensis, three different metabolic states were observed in continuous culture. At dilution rates between 0.18 h^–1 and 0.31 h^–1 vegetative cells, sporulating bacteria and spores coexisted, while glucose and amino acids were consumed. Only vegetative cells were observed at dilution rates between 0.42 h^–1 and 0.47 h^–1 and glucose was used as the main carbon and energy source. AtD = 0.50 h^–1 the biomass yield on glucose decreases sharply. To define better the specific growth rate range in which the microorganism uses mainly glucose, a dilution rate of 0.25–0.45 h^–1 was studied. The experimental data could be adjusted to a Monod model and the following rate coefficients and growth yields were determined: maximum specific growth rate 0.54 h^–1, saturation constant 0.56 mg glucose ml^–1, biomass growth yields 0.43 g cells (g glucose)^–1, and 0.76 g cells (g oxygen)^–1, and maintenance coefficients 0.065 g glucose (g cells)^–1 h^–1 and 0.039 g oxygen (g cells)^–1 h^–1.     

Continuous culture of the hyperthermophilic archaeum Pyrococcus furiosus

Summary A system for continuous culture of the hyperthermophilic archaeum Pyrococcus furiosus in the absence of elemental sulphur has been developed. An all-glass gas-lift bioreactor was used to provide high mass transfer at low shear forces, whilst eliminating the potential for corrosion. Steady-state cell densities of P. furiosus were found to increase with higher inert gas flow rates, reaching a maximum in this system with 0.5 vol. vol^–1 min^–1 of nitrogen (N₂). N₂ permitted higher cell densities than the other inert gases tested (argon, helium and sulphur hexafluoride) under equivalent conditions. At 0.5 vol. vol^–1 min^–1 of N₂ a cell density in excess of 3 × 10⁹ ml^–1 could be maintained indefinitely at a dilution rate of 0.2 h^–1. Higher dilution rates gave progressively lower steady-state cell densities. Teh biomass production was maximal, however, at a dilution rate of 0.4 h^–1. At this dilution rate the bioreactor was able to generate more than 1.5 g wet weight of cells h^–1 l^–1 culture volume.Correspondence to: N. Raven