An evaluation of the microscopical counting methods of the tape in hirst-burkard pollen and spore trap

Three different sampling units in current use and different sampling strategies were tested. Randomly placed microscope fields are good in estimating the daily mean concentration, but very big sample size is needed. Traverses across the slide in systematic order are best to estimate the shortterm concentrations and diurnal variation. A formula for the estimation of the error in one transverse traverse is given. Twelve transverse traverses in systematic order is also enough to estimate the daily mean concentration. One or two traverses along the length of the slide give often unreliable estimates because of the irregularities in the transverse variation of the particle concentrations on the slide. For the same reason it is not safe to choose an “effectively collecting area”. Instead the whole width of the tape should be studied.     

An evaluation of two methods used for microscopic analysis of airborne fungal spore concentrations from the Burkard Spore Trap

The Burkard Volumetric Spore Trap is a common and efficient instrument used to collect outdoor air samples. In North America, two slide counting methods have been widely used by aerobiologists: the single longitudinal traverse method and the twelve transverse traverse method. The purpose of this study was to compare the two counting methods by assessing fungal spore concentrations of ascospores, basidiospores, smut teliospores, Cladosporium, Alternaria, Epicoccum, Curvularia, Drechslera, Pithomyces, other spores, and total spores at two metropolitan Tulsa, Oklahoma sites (Tulsa and Hectorville) during September 1996. Results showed that both methods were sensing parallel fluctuations in average daily spore concentration, although the twelve transverse traverse method usually resulted in higher concentrations. At the Tulsa site, the twelve transverse traverse method gave statistically higher concentrations than the single longitudinal traverse method except for Epicoccum, Pithomyces, smut teliospores, and other spores. At the Hectorville site, however, only Cladosporium and basidiospores showed that the twelve transverse traverse method was statistically higher than the single longitudinal traverse method. Comparison with concentrations obtained by counting the total slide surface of two slides indicated that neither method was equivalent to the total slide spore count, although the twelve transverse traverse method gave a lower absolute percent difference from the total slide surface concentration. While the twelve transverse traverse method gave slightly better approximations of the spore concentration, the increase in accuracy may not justify the extra effort required to analyze with this method.     

Comparison between two adhesives (silicone and petroleum jelly) in Hirst pollen traps in a controlled environment

Aerobiological sampling through volumetric pollen traps requires the use of an appropriate adhesive, whose selection is a critical factor in these studies. This study compares the differences between two adhesives that have been widely used in aerobiological studies with the aim of providing a persuasive argument for using petroleum jelly as a viable alternative to silicone diluted with the banned substance carbon tetrachloride. The study was performed using Hirst-type pollen traps in an indoor controlled environment to avoid interference attributed to outdoor meteorological parameters. Furthermore, a gravimetric study was conducted simultaneously as a control. Four different pollen types with different pollen sizes and similar flowering seasons were studied (Acer, Platanus, Quercus and Rumex). Differences between pollen traps were minimised by interchanging the drums in each pollen trap every 24 hours. Gravimetric results showed homogeneous airborne pollen distribution in the study. No statistically significant differences were found between the results for the sample adhesives for Quercus and Platanus, whereas significant differences were observed for Rumex and Acer. In the case of Acer, more pollen grains were recorded using the petroleum jelly, while for Rumex, more pollen grains were recorded with silicone. After this experiment we consider that petroleum jelly can be used as a viable alternative adhesive to the banned silicone diluted with carbon tetrachloride.     

Airborne pollen in Genoa (NW-Italy): a comparison between two pollen-sampling stations

A comparison between two pollen-sampling stationsin the city area of Genoa is presented. The samplingsites are placed 3 km apart, respectively in theeastern urban area (St. Martino Hospital – S.M.) andin the historical centre (Botanical Garden – B.G.).Pollen sampling was carried out during the years1995–1997 at the two different sites by volumetricHirst-type sampler and then compared. The dailyairborne pollen concentration of Urticaceae, Poaceae,Cupressaceae/Taxaceae, Corylaceae/Betulaceae andOleaceae resulted prevailingly higher at S.M., while a good correspondence was observed from a phenologicpoint of view. Asteraceae have shown the bestqualitative-quantitative consistency. In springtime adifference was recorded for Urticales, maybe due tolocal occurence (B.G.) of Broussonetia papyrifera(Moraceae). On the whole, the correspondence betweenthe two different sampling stations proved to besatisfactory.     

Development of a semi-automatic system for pollen recognition

A semi-automatic system for pollen recognitionis studied for the european project ASTHMA. The goal of such a system is to provideaccurate pollen concentration measurements. This information can be used as well by thepalynologists, the clinicians or a forecastsystem to predict pollen dispersion. At first,our emphasis has been put on Cupressaceae, Olea, Poaceae and Urticaceae pollen types. The system is composed of two modules: pollengrain extraction and pollen grain recognition. In the first module, the pollen grains areobserved in light microscopy and are extractedautomatically from a pollen slide coloured withfuchsin and digitized in 3D. In the secondmodule, the pollen grain is analyzed forrecognition. To accomplish the recognition, itis necessary to work on 3D images and to usedetailed palynological knowledge. Thisknowledge describes the pollen types accordingto their main visible characteristerics and tothose which are important for recognition. Somepollen structures are identified like the porewith annulus in Poaceae, the reticulum in Oleaand similar pollen types or the cytoplasm inCupressaceae. The preliminary results show therecognition of some pollen types, likeUrticaceae or Poaceae or some groups of pollentypes, like reticulate group.     

Comparison of intradiurnal variation of airborne pollen in Mar del Plata (Argentina). Part I. Non-arboreal pollen

Intradiurnal variation of non-arboreal pollen (NAP) aredescribed in relation to the associated weather using the data obtainedwith a Burkard trap in Mar del Plata city, for a three year data set(1988, 1992 and 1995). The daily pattern of concentration was quitehomogeneous during the years analysed except for 1995, when it showed avariation due to the change of position of the station. Qualitativecomposition of the NAP airborne pollen was mainly represented byPoaceae, Plantago and Cyperaceae during the three years. The daily trendshowed high concentrations during daylight hours, when instability andconvective movements prevail, and low concentrations in the night, whenmeteorological conditions favour the development of a stable stratifiedlayer.     

The effect of sample composition and vial type on Ĉerenkov counting in a liquid scintillation counter

The effect of sample vial type and sample composition on the ?erenkov count rate detected from ³²P and ³⁶Cl was studied using a liquid scintillation counter. When counting was done in the noncoincident mode, glass vials allowed higher counting efficiency than plastic vials. In the coincident mode light scattering caused by polyethylene and polyproplyene vials allowed higher counting efficiency than glass vials. Highest coincident counting efficiency was from plastic minivials in a glass carrier vial. Increased solute concentration in samples caused increased counting efficiency due to changes in the refractive index of the solution. This can cause significant counting efficiency changes with no sample channel ratio change in density gradient fractions. The use of wavelength shifters is shown to be inappropriate when the sample pH varies, as this can change the fluorescent properties of the shifters and thereby the observed count rate.     

Comparison of some pollen concentrations in Finland and the Estonian SSR

Summary Pollen and spore concentrations were compared in Tartu, Estonia and in three sites in Finland (Turku, Kuopio and Oulu) during May–September 1989. The onset ofQuercus, Pinus, Poaceae,Urtica andRumex flowering started earlier in Tartu than at any site in Finland. The flowering ofJuniperus andArtemisia, on the other hand, began earlier in Turku and Kuopio than in Tartu.Pinus andJuniperus showed a significant correlation (number of pollen grains at the same date) between Tartu and Turku and between Turku and Kuopio. Poaceae andUrtica were correlated between all the sites, as wasRumex except between Tartu and Turku.Artemisia was correlated between Tartu and Turku, Turku and Oulu, and Kuopio and Oulu.Cladosporium correlated between Tartu and Turku. The pollen seasons of Poaceae,Urtica andRumex are prolonged towards the south.     

A comparative study of pollen trends in Genoa and Sanremo (Italy) from 1981 to 1989

Summary Trends of the atmospheric dispersion of the pollens of Urticaceae, Poaceae, Asteraceae,Plantago, Chenopodiaceae-Amaranthaceae, Polygonaceae, Oleaceae, Betulaceae-Corylaceae,Quercus, Castanea, and Cupressaceae-Taxaceae were studied from 1981 to 1989 in two localities (Genoa and Sanremo) about 120 km apart on the coast of Liguria in Italy. Statistical analysis revealed, in particular, and overall increase in pollen rain in Genoa during the period considered. The following observations were carried out on the pollens of greatest allergological interest: Urticaceae, a slightly increasing trend in Genoa; Poaceae, a moderately increasing trend in Sanremo; Oleaceae, almost parallel, uniform trendsin both centres. The values of this study lies in its ability to point out any increase which may occur over the years in the dispersal of certain allergenic pollens.     

Estimating red deer Cervus elaphus populations: an analysis of variation and cost-effectiveness of counting methods

• 1 Different counting methods are currently used to estimate red deer populations in the open range in Scotland, but there are few data available to compare variation in estimates, or relative cost‐effectiveness.
• 2 While it is impossible to determine the accuracy of counts (as real numbers are unknown), variation within and between different methods can be measured by repeat counts of the same area within as short a period as possible.
• 3 This study aimed to quantify the variation observed from repeat counts using each of four methods (ground, helicopter, infrared helicopter and dung‐counting methods) at one of three study sites in late winters 2003, 2004 and 2005. Additional data from digital camera images of groups from counts in other areas of Scotland were also used to assess the accuracy of visual counts.
• 4 Coefficients of variation (CVs) within any method of between 5% and 16% were recorded, consistent with previous comparisons for red deer open range counts in Scotland. CVs were lowest for ground and helicopter counts. The infrequency of optimal conditions was likely to limit the applicability of infrared counts in Scotland.
• 5 In terms of cost‐effectiveness, helicopter counting was the least labour‐intensive, with costs of other techniques depending on the availability of existing manpower as an overhead cost.
• 6 It is concluded that helicopter counts are most likely to minimize errors while maximizing cost‐efficiency. Accuracy can be improved by the use of digital photography for counting larger deer groups. Estimates are likely to be improved further by increasing the frequency of counts and using the same methods, counters and routes for repeat counts.

     

Three-dimensional reconstruction and characterization of human external shapes from two-dimensional images using volumetric methods

This work presents a volumetric approach to reconstruct and characterise 3D models of external anatomical structures from 2D images. Volumetric methods represent the final volume using a finite set of 3D geometric primitives, usually designed as voxels. Thus, from an image sequence acquired around the object to reconstruct, the images are calibrated and the 3D models of the referred object are built using different approaches of volumetric methods. The final goal is to analyse the accuracy of the obtained models when modifying some of the parameters of the considered volumetric methods, such as the type of voxel projection (rectangular or accurate), the way the consistency of the voxels is tested (only silhouettes or silhouettes and photo-consistency) and the initial size of the reconstructed volume.     

Comparison of methods used in zooplankton sampling and counting in the joint Russian-Finnish evaluation of the trophic state of Lake Ladoga

The results of a joint Russian-Finnish investigation on zooplankton in Lake Ladoga are presented, and a comparison is made between two sampling techniques, tube sampler and plankton net, and between two counting methods. The precision of subsampling and sampling is further discussed on the basis of zooplankton data gathered in Lake Saimaa, Finland. The comparison clearly indicates that a tube sampler is required for reliable sampling of small-sized animals, while a plankton net saves time and is a more economical sampler for large, rare or active animals. The comparison between the results obtained by Finnish and Russian workers, using different counting procedures, shows that the main groups of crustacean zooplankton are similarly counted and identified in the two laboratories.     

两种稻田摇蚊采集方法的比较

本文介绍了一种较为简便和节省人工的稻田摇蚊田间取样方法:笼罩法,并将笼罩法得到的稻田摇蚊群落结构和发生动态和吸虫器法得到的结果进行了比较。研究结果表明:在水稻的4个生育期中,笼罩法和吸虫器法均采集到了中华摇蚊Chironomus sinicus Kiknadze,Wang,Istomina&Gunderina;台湾长跗摇蚊Tanytarsus formosanus Kieffer;云集多足摇蚊Polypedilum nubifer Skuse和刺铗长足摇蚊Tanypus puncitpennis Meigen,而吸虫器法还采集到微小沼摇蚊Limnophyes minimus Meigen。其中中华摇蚊和台湾长跗摇蚊为优势类群,笼罩法取样得到的两种优势种种群密度均高于吸虫器法的,例如在拔节期时笼罩法取样得到台湾长跗摇蚊的种群密度是吸虫器法的22倍。通过取样变异系数的比较发现,两种方法精确性都并不理想,在今后的试验中可以通过增加取样的样点量或取样面积来提高精确度。相比较而言吸虫器法操作复杂,而且较为耗时,在实际操作中往往受到一定条件的限制,而笼罩法则具有操作简便、准确度高等优点,试验安排可以进行高频率取样,能够更准确地反映田间摇蚊的种群动态。因此,笼罩法为以后研究与摇蚊生活习性相似的稻田节肢动物类群(如蚊科昆虫)提供了一种新的取样方案。     

Comparative evaluation of methods for counting surviving biofilm cells adhering to a polyvinyl chloride surface exposed to chlorine or drying

Aim:  To compare techniques for assessing biofilm populations previously subjected, or not, to inimical treatment by chlorine or drying.
Methods and Results:  Four sonication treatments and swabbing were compared on Salmonella  Typhimurium or Pseudomonas fluorescens biofilms grown on polyvinyl chloride (PVC). The apparatuses emitting the highest ultrasound energy were the most efficient except on Salm. Typhimurium biofilms subjected to drying: a lethal effect, leading to an underestimation of at least 1·5 log (CFU cm^–2) was observed with the more aggressive treatment. The differences between the highest count and the swabbing counts ranged from 0·3 log (CFU cm^–2) (untreated Salm. Typhimurium) to 1·7 log (CFU cm^–2) (chlorine treated Ps. fluorescens ). Impedance measurements, used to assess populations without detaching any cells showed that the calibration curves that were built up from data obtained with suspended cells plus PVC slides were not appropriate.
Conclusions:  High energy ultrasound techniques designed either for in vitro or in situ studies proved efficient in assessing the number of attached CFU. However, the right treatment duration has to be carefully established before using high energy ultrasound techniques.
Significance and impact of the study:  The effectiveness of a cleaning and disinfection regime inferred from data obtained after swabbing may be greatly underestimated.     

Predicting the start of the birch pollen season at London, Derby and Cardiff, United Kingdom, using a multiple regression model, based on data from 1987 to 1997

Recent changes in weather in North-West Europehave been reflected in the start dates ofpollen seasons. It is therefore necessary toupdate previous models, such as the oneproduced by Jones (1995), so that the modelwill be weighted by current weather patterns. Birch pollen data, collected over a period ofeleven years (1987 to 1997 inclusive) fromthree pollen counting stations in the UK,London, Derby and Cardiff, were analysed todetermine the start dates using the Sum75method. The start dates of the birch pollenseasons of the eleven-year period were thentested for significance against ten-dayaggregated variables of temperature andrainfall for each site. The significantvariables were entered into multiple regressionmodels until the most valid equation for eachsite was found. The models were then tested onthree years not included in their data sets. The models showed mean differences betweenactual and predicted start dates, for theeleven years used, of 1.5, 3 and 5 days atDerby, Cardiff and London respectively. Forthe test years the mean difference was 1, 4.5and 7.5 days at Derby, Cardiff and Londonrespectively. The most powerful model was forDerby where the corresponding meteorologicalstation is at 0.5 km distance and the weakestwas for London where the correspondingmeteorological station is much further away at21 km distance. Weather variables from earlyFebruary to mid March were found to be the mostinfluential on the start dates of the birchpollen season at the three sites.     

麦冬多糖精制方法的比较

Five preparation methods were used to purify the crude polysaccharide which was the co-products of preparation saponin from Ophiopogonis japonicus (Thunb.)Ker-Gawl.The results indicate that the method of enzyme hydrolysis could purify the crude polyseccharide efficiently.The content of polysaccharide is more than 85% and could be used as the foods and medicine raw material.Aduanced test showcd that the polysaccharide is mainly consist of glucose,fructose,xylose,rhannose and galactose.     

DNA isolation from museum and type collection slides of microsporidia

DNA from 19 species of microsporidia was isolated and amplified from infected host tissue that were originally prepared between the years 1946 and 1996. The smears, on glass microscope slides, were either Giemsa-stained or unstained. Methanol-fixed, Giemsa-stained smears proved to be suitable for DNA isolation; DNA was amplified from only two of 14 unstained slides. The isolated DNA was successfully amplified in PCRs using small subunit and large subunit rDNA primers and sequenced. The high efficiency of DNA isolation demonstrates the usefulness of archival and type collection slides for some molecular biology and molecular taxonomy studies.     

14型肺炎链球菌荚膜多糖纯化工艺中两种去除蛋白方法的比较

目的苯酚抽提法和脱氧胆酸钠沉淀法去除14型肺炎链球菌荚膜多糖中蛋白质的效果比较。方法将3批次14型肺炎链球菌发酵培养液经超滤、乙醇沉淀等方法初步纯化后,平分成两份,分别采用苯酚抽提法和脱氧胆酸钠沉淀法去除蛋白,通过比较多糖收获量、多糖组分检定结果、多糖分子质量、多糖抗原活性、多糖核磁共振图谱,以此评价这两种蛋白去除方法的效果。结果与苯酚抽提法相比,脱氧胆酸钠沉淀法制备的14型肺炎链球菌纯化荚膜多糖除收获量较高,蛋白和核酸杂质含量较低外,氨基己糖含量、多糖分子质量、抗原活性和多糖核磁共振图谱的检定分析结果无显著性差异(P>0.1)。结论作为14型肺炎链球菌荚膜多糖纯化工艺中的除蛋白方法,脱氧胆酸钠沉淀法优于苯酚抽提法。