From lactic acid to poly(lactic acid) (PLA): characterization and analysis of PLA and its precursors

The quality of the monomers lactic acid and lactide as well as the chemical changes induced during polymerization and processing are crucial parameters for controlling the properties of the resulting poly(lactic acid) (PLA) products. This review presents the most important analysis and characterization methods for quality assessment of PLA and its precursors. The impurities typically present in lactic acid or lactide monomers and their possible origins and effects on resulting PLA products are discussed. The significance of the analyses for the different polymer production stages is considered, and special applications of the methods for studying features specific for PLA-based materials are highlighted.     

Branched poly(lactide) synthesized by enzymatic polymerization: effects of molecular branches and stereochemistry on enzymatic degradation and alkaline hydrolysis

In this article the effects of the number of molecular branches (chain ends) and the stereochemistry of poly(lactide)s (PLAs) on the enzymatic degradation and alkaline hydrolysis are studied. Various linear and branched PLAs were synthesized using lipase PS (Pseudomonas fluorescens)-catalyzed ring-opening polymerization (ROP) of lactide monomers having different stereochemistries (L-lactide, D-lactide, and D,L-lactide). Five different alcohols were used as initiators for the ROP, and the monomer-to-initiator molar feed ratio was varied from 10 to 100 and 1000 for each branch in the polymer architecture. The properties of branched PLAs that would affect the enzymatic and alkaline degradations, i.e., the glass transition temperature, the melting temperature, the melting enthalpy, and the advancing contact angle, were determined. The PLA films were degraded using proteinase K or 1.0 M NaOH solution, and the weight loss and changes in the number average molecular weight (Mn) of the polymer were studied during 12 h of degradation. The results suggest that an increase in the number of molecular branches of branched PLAs enhances its enzymatic degradability and alkali hydrolyzability. Moreover, the change in Mn of the branched poly(L-lactide) (PLLA) by alkaline hydrolysis indicated that the decrease in Mn was in the first place dependent on the number of molecular branches and thereafter on the length of the molecular branch of branched PLA. The branched PLLA, poly(D-lactide) (PDLA), and poly(D,L-lactide) (PDLLA) differed in weight loss and change in Mn of the PLA segment during the enzymatic degradation. It is suggested that the branched PDLLA was degraded preferentially by proteinase K.     

Compatibilization effect of poly(epsilon-caprolactone)-b-poly(ethylene glycol) block copolymers and phase morphology analysis in immiscible poly(lactide)/poly(epsilon-caprolactone) blends

The miscibility and phase behavior of two stereoisomer forms of poly(lactide) (PLA: poly (L-lactide) (PLLA) and poly(DL-lactide) (PDLLA)) blends with poly(epsilon-caprolactone)-b-poly(ethylene glycol) (PCL-b-PEG) and PCL-b-monomethoxy-PEG (PCL-b-MPEG) block copolymers have been investigated by differential scanning calorimetry (DSC). The DSC thermal behavior of both the blend systems revealed that PLA is miscible with the PEG segment phase of PCL-b-(M)PEG but is still immiscible with its PCL segment phase although PCL was block-copolymerized with PEG. On the basis of these results, PCL-b-PEG was added as a compatibilizer to PLA/PCL binary blends. The improvement in mechanical properties of PLA/PCL blends was achieved as anticipated upon the addition of PCL-b-PEG. In addition, atomic force microscopy (AFM) measurements have been performed in order to study the compositional synergism to be observed in mechanical tests. AFM observations of the morphological dependency on blend composition indicate that PLA/PCL blends are immiscible but compatible to some extent and that synergism of compatibilizing may be maximized in the compositional blend ratio before apparent phase separation and coarsening.     

In-situ formation of biodegradable hydrogels by stereocomplexation of PEG-(PLLA)8 and PEG-(PDLA)8 star block copolymers

Eight-arm poly(ethylene glycol)-poly(L-lactide), PEG-(PLLA)(8), and poly(ethylene glycol)-poly(D-lactide), PEG-(PDLA)(8), star block copolymers were synthesized by ring-opening polymerization of either L-lactide or D-lactide at room temperature in the presence of a single-site ethylzinc complex and 8-arm PEG (M(n) = 21.8 x 10(3) or 43.5 x 10(3)) as a catalyst and initiator, respectively. High lactide conversions (>95%) and well-defined copolymers with PLLA or PDLA blocks of the desired molecular weights were obtained. Star block copolymers were water-soluble when the number of lactyl units per poly(lactide) (PLA) block did not exceed 14 and 17 for PEG21800-(PLA)(8) and PEG43500-(PLA)(8), respectively. PEG-(PLA)(8) stereocomplexed hydrogels were prepared by mixing aqueous solutions with equimolar amounts of PEG-(PLLA)(8) and PEG-(PDLA)(8) in a polymer concentration range of 5-25 w/v % for PEG21800-(PLA)(8) star block copolymers and of 6-8 w/v % for PEG43500-(PLA)(8) star block copolymers. The gelation is driven by stereocomplexation of the PLLA and PDLA blocks, as confirmed by wide-angle X-ray scattering experiments. The stereocomplexed hydrogels were stable in a range from 10 to 70 degrees C, depending on their aqueous concentration and the PLA block length. Stereocomplexed hydrogels at 10 w/v % polymer concentration showed larger hydrophilic and hydrophobic domains as compared to 10 w/v % single enantiomer solutions, as determined by cryo-TEM. Correspondingly, dynamic light scattering showed that 1 w/v % solutions containing both PEG-(PLLA)(8) and PEG-(PDLA)(8) have larger "micelles" as compared to 1 w/v % single enantiomer solutions. With increasing polymer concentration and PLLA and PDLA block length, the storage modulus of the stereocomplexed hydrogels increases and the gelation time decreases. Stereocomplexed hydrogels with high storage moduli (up to 14 kPa) could be obtained at 37 degrees C in PBS. These stereocomplexed hydrogels are promising for use in biomedical applications, including drug delivery and tissue engineering, because they are biodegradable and the in-situ formation allows for easy immobilization of drugs and cells.     

Solid-phase synthesis of functionalized bis-peptides

We demonstrate the first solid-phase synthesis of highly functionalized bis-peptides. Bis-peptides are ladder oligomers composed of stereochemically pure, cyclic bis-amino acids joined by substituted diketopiperazine linkages. They have a shape-programmable backbone that is controlled by controlling the stereochemistry and sequence of the monomers within each oligomer. Functionalized bis-peptides are assembled using a new amide bond forming reaction (acyl-transfer coupling) that we have previously developed and a novel activation strategy that allows the sequential formation of penta- and hexa-substituted diketopiperazines from extremely hindered N-alkyl-alpha,alpha-disubstituted amino acids. We present mechanistic evidence that acyl-transfer coupling is competitive with direct acylation in the formation of hindered amide bonds. We also detail the synthesis of four functionalized bis-peptides, and that by combining bis-peptides with amino acids through diketopiperazine linkages, bis-peptides can mimic the display of residues i, i+4, i+7 of an alpha-helical peptide.     

Use of low MW polylactic acid and lactide to stimulate growth and yield of soybeans

Polylactic acid (PLA) is an environmentally friendly, degradable polymer which has been suggested for use as a matrix for controlled release of herbicides. The growth stimulation and yield improvement potential of low molecular weight (MW), poly(D,L-lactic acid) and D,L-lactide were evaluated using preplant soil incorporation with soybeans (Glycine max (L.) Merrill). Greenhouse studies confirmed that both lactide and PLA increased soybean leaf area, pod number, bean number and bean and plant dry weight. Soybean seed yield was increased most dramatically (130%; 2.3 fold) by weekly 30 ppm lactide addition and also by single addition of low MW (3500 Daltons) PLA (40.6%; 1.4 fold). Low levels of PLA were stimulatory (15–30 ppm), while higher levels were inhibitory, with some interaction with growth conditions being evident. The stimulatory component was most readily provided by weekly lactide addition, but was also provided by slow-release, hydrolytic breakdown of PLA in the soil, with 3500 Daltons MW being better than higher MW PLA. In field studies at two locations, PLA (16.8 and 45.8 kg ha^–1) increased soybean plot yield as much as 18%, being reflected in increases in both growth and per plant yield components (plant dry wt, seed number, seed dry wt, and number of branch pods and seeds). The levels used in field studies were selected to be similar to the level of a typical carrier used in slow release of herbicides. This study suggests that use of PLA as an encapsulation matrix for herbicides could provide reduced environmental impact and improved weed control, while at the same time increasing yield of soybeans through release of a plant growth stimulant in the form of oligomeric or monomeric lactic acid.     

Process of Making Three-dimensional Microstructures using Vaporization of a Sacrificial Component

Vascular structures in natural systems are able to provide high mass transport through high surface areas and optimized structure. Few synthetic material fabrication techniques are able to mimic the complexity of these structures while maintaining scalability. The Vaporization of a Sacrificial Component (VaSC) process is able to do so. This process uses sacrificial fibers as a template to form hollow, cylindrical microchannels embedded within a matrix. Tin (II) oxalate (SnOx) is embedded within poly(lactic) acid (PLA) fibers which facilitates the use of this process. The SnOx catalyzes the depolymerization of the PLA fibers at lower temperatures. The lactic acid monomers are gaseous at these temperatures and can be removed from the embedded matrix at temperatures that do not damage the matrix. Here we show a method for aligning these fibers using micromachined plates and a tensioning device to create complex patterns of three-dimensionally arrayed microchannels. The process allows the exploration of virtually any arrangement of fiber topologies and structures.     

Polymers from Amino acids: Development of Dual Ester-Urethane Melt Condensation Approach and Mechanistic Aspects

A new dual ester-urethane melt condensation methodology for biological monomers-amino acids was developed to synthesize new classes of thermoplastic polymers under eco-friendly and solvent-free polymerization approach. Naturally abundant l-amino acids were converted into dual functional ester-urethane monomers by tailor-made synthetic approach. Direct polycondensation of these amino acid monomers with commercial diols under melt condition produced high molecular weight poly(ester-urethane)s. The occurrence of the dual ester-urethane process and the structure of the new poly(ester-urethane)s were confirmed by (1)H and (13)C NMR. The new dual ester-urethane condensation approach was demonstrated for variety of amino acids: glycine, β-alanine, l-alanine, l-leucine, l-valine, and l-phenylalanine. MALDI-TOF-MS end group analysis confirmed that the amino acid monomers were thermally stable under the melt polymerization condition. The mechanism of melt process and the kinetics of the polycondensation were studied by model reactions and it was found that the amino acid monomer was very special in the sense that their ester and urethane functionality could be selectively reacted by polymerization temperature or catalyst. The new polymers were self-organized as β-sheet in aqueous or organic solvents and their thermal properties such as glass transition temperature and crystallinity could be readily varied using different l-amino acid monomers or diols in the feed. Thus, the current investigation opens up new platform of research activates for making thermally stable and renewable engineering thermoplastics from natural resource amino acids.     

Fine structure and enzymatic degradation of poly[(R)-3-hydroxybutyrate] and stereocomplexed poly(lactide) nanofibers

Fiber morphology and crystalline structure of poly[(R)-3-hydroxybutyrate] (P(3HB)) and stereocomplexed poly(lactide) (PLA) nanofibers were investigated by using scanning and transmission electron microscopies and X-ray and electron diffractions. In the P(3HB) nanofibers spun from less than 1 wt% 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP) solution, planar zigzag conformation (beta-form) as well as 2(1) helix conformation (alpha-form) structure was formed. Based on the electron diffraction measurement of single P(3HB) nanofiber, it was revealed that the molecular chains of P(3HB) align parallel to the fiber direction. From the enzymatic degradation test of P(3HB) nanofiber, it was shown that beta-form molecular chains are degraded more preferentially than alpha-form chains. Stereocomplexed PLA nanofibers were electrospun from 1 wt% poly(l-lactide)/poly(d-lactide) (PLLA/PDLA) solution in HFIP, which contains equal amounts of PLLA and PDLA. While as-spun stereocomplexed PLA nanofiber was amorphous, PLA nanofiber annealed at 100 degrees C contained only racemic crystal. It was supposed that the crystallization behavior of stereocomplexed PLA in the nanofiber is affected by the electrospinning process, which forcibly exerts the strain onto the polymer chains.     

Cloning and sequencing of a poly(DL-lactic acid) depolymerase gene from Paenibacillus amylolyticus strain TB-13 and its functional expression in Escherichia coli

The gene encoding a poly(DL-lactic acid) (PLA) depolymerase from Paenibacillus amylolyticus strain TB-13 was cloned and overexpressed in Escherichia coli. The purified recombinant PLA depolymerase, PlaA, exhibited degradation activities toward various biodegradable polyesters, such as poly(butylene succinate), poly(butylene succinate-co-adipate), poly(ethylene succinate), and poly(epsilon-caprolactone), as well as PLA. The monomeric lactic acid was detected as the degradation product of PLA. The substrate specificity toward triglycerides and p-nitrophenyl esters indicated that PlaA is a type of lipase. The gene encoded 201 amino acid residues, including the conserved pentapeptide Ala-His-Ser-Met-Gly, present in the lipases of mesophilic Bacillus species. The identity of the amino acid sequence of PlaA with Bacillus lipases was no more than 45 to 50%, and some of its properties were different from those of these lipases.     

Synthesis and properties of star-shaped polylactide attached to poly(amidoamine) dendrimer

Star-shaped polylactide was synthesized by bulk polymerization of lactide with poly(amidoamine) (PAMAM) dendrimer as initiator, which was marked as PAMAM-g-PLA for simplicity. The nonlinear architecture of PAMAM-g-PLA was confirmed by gel permeation chromatograph, nuclear magnetic resonance, and differential scanning calorimetry analysis. Unlike the linear polylactide (PLA) with similar molecular weight, PAMAM-g-PLA had a higher hydrophilicity and a faster degradation rate because of shortened polymer chains and increased polar terminal endgroups due to its branch structure. The highly branched structure significantly accelerated the release of water-soluble bovine serum albumin from PAMAM-g-PLA microspheres, whereas the linear PLA with similar molecular weight exhibited an initial time lag release. This star polymer may have potential applications for hydrophilic drug delivery in tissue engineering, including growth factor and antibodies to induce tissue regeneration, by adjusting the chain lengths of PLA branches.     

Biocompatible and biodegradable polymersome encapsulated hemoglobin: a potential oxygen carrier

This work describes the development of polymersome-encapsulated hemoglobin (PEH) self-assembled from biodegradable and biocompatible amphiphilic diblock copolymers composed of poly(ethylene oxide) (PEO), poly(caprolactone) (PCL), and poly(lactide) (PLA). In the amphiphilic diblock, PEO functions as the hydrophilic block, while either PCL or PLA can function as the hydrophobic block. PEO, PCL, and PLA are biocompatible polymers, while the last two polymers are biodegradable. PEH dispersions were prepared by extrusion through 100 nm pore radii polycarbonate membranes. In this work, the encapsulation efficiency of human and bovine hemoglobin (hHb and bHb) in polymersomes was adjusted by varying the initial concentration of Hb. This approach yielded Hb loading capacities that were comparable to values in the literature that supported the successful resuscitation of hamsters experiencing hemorrhagic shock. Moreover, the Hb loading capacities of PEHs in this study can also be tailored simply by controlling the diblock copolymer concentration. In this study, typical Hb/diblock copolymer weight ratios ranged 1.2-1.5, with initial Hb concentrations less than 100 mg/mL. The size distribution, Hb encapsulation efficiency, oxygen affinity (P 50), cooperativity coefficient (n), and methemoglobin (metHb) level of these novel PEH dispersions were consistent with values required for efficient oxygen delivery in the systemic circulation. Taken together, our results demonstrate the development of novel PEH dispersions that are both biocompatible and biodegradable. These novel dispersions show very good promise as therapeutic oxygen carriers.     

Perspectives to produce positively or negatively charged polyhydroxyalkanoic acids

An overview is provided on the possibilities of producing positively and negatively charged poly(β-hydroxyalkanoates), PHAs. A large variety of bacterial polyesters with functionalized terminal side chains can be produced in microbial fermentation processes by a direct polymerization of respective carbon sources, that is, carbon sources that carry functional groups in their ω-position. However, charged PHAs are not accessible by a direct approach and must be synthesized via polymer-analogous reactions of functionalized bacterial polyesters. PHA polyanions are produced by converting the terminal functional groups into carboxylate groups, while PHA polycations are produced by introducing terminal amino groups. PHAs with terminal vinyl groups emerged as most suitable PHA precursors, as they can be produced in relatively high yields and the double bonds are sufficiently reactive. The oxidation of vinyl groups yields PHA polyanions. The conversion of terminal vinyl groups into epoxides with a subsequent ring-opening reaction with an amine yields PHA polycations. Other functionalized PHA that potentially lend themselves to polymer-analogous reactions are reviewed.     

Facile synthesis of multiamino vinyl poly(amino acid)s for promising bioapplications

We presented a general and facile strategy to prepare biocompatible multiamino polymers. Series of new monomers were synthesized by esterification of 2-hydroxyethyl methacrylate (HEMA) and Boc-amino acids, such as Boc-l-phenylalanine, Boc-glycine, Boc-l-alanine, Boc-l-valine, and Boc-l-lysine. Subsequent vinyl polymerization of monomers gave rise to vinyl poly(amino acid)s with a side primary amino group at each unit if deprotected. Both atom transfer radical polymerization (ATRP) and conventional free radical polymerization (FRP) were employed to prepare the multiamino polymers. A well controlled effect upon molecular weight with the standard first-order kinetics was achieved in cases of ATRP, and high molecular weight polymers were obtained via FRP. MTT assay showed that cell survival rates for the multiamino polymers were almost maintained above 90% and that their cytotoxicities were much lower than that of linear PEI (PEI 25000). Zeta potential measurements demonstrated that the vinyl poly(amino acid)s are electropositive, and AFM measurements showed that the vinyl poly(amino acid)s could tightly condense DNA into granular structures at a suitable concentration. The combination of facile availability, controlled productivity, low cytotoxicity and strong binding ability with DNA promises the great potential of the novel multiamino polymers in bioapplications.     

Gelation characteristics and osteogenic differentiation of stromal cells in inert hydrolytically degradable micellar polyethylene glycol hydrogels

The use of poly(ethylene glycol) (PEG) hydrogels in tissue engineering is limited by their persistence in the site of regeneration. In an attempt to produce inert hydrolytically degradable PEG-based hydrogels, star (SPELA) poly(ethylene glycol-co-lactide) acrylate macromonomers with short lactide segments (<15 lactides per macromonomer) were synthesized. The SPELA hydrogel was characterized with respect to gelation time, modulus, water content, sol fraction, degradation, and osteogenic differentiation of encapsulated marrow stromal cells (MSCs). The properties of SPELA hydrogel were compared with those of the linear poly(ethylene glycol-co-lactide) acrylate (LPELA). The SPELA hydrogel had higher modulus, lower water content, and lower sol fraction than the LPELA. The shear modulus of SPELA hydrogel was 2.2 times higher than LPELA, whereas the sol fraction of SPELA hydrogel was 5 times lower than LPELA. The degradation of SPELA hydrogel depended strongly on the number of lactide monomers per macromonomer (nL) and showed a biphasic behavior. For example, as nL increased from 0 to 3.4, 6.4, 11.6, and 14.8, mass loss increased from 7 to 37, 80, 100% and then deceased to 87%, respectively, after 6 weeks of incubation. The addition of 3.4 lactides per macromonomer (<10 wt % dry macromonomer or <2 wt % swollen hydrogel) increased mass loss to 50% after 6 weeks. Molecular dynamic simulations demonstrated that the biphasic degradation behavior was related to aggregation and micelle formation of lactide monomers in the macromonomer in aqueous solution. MSCs encapsulated in SPELA hydrogel expressed osteogenic markers Dlx5, Runx2, osteopontin, and osteocalcin and formed a mineralized matrix. The expression of osteogenic markers and extent of mineralization was significantly higher when MSCs were encapsulated in SPELA hydrogel with the addition of bone morphogenetic protein-2 (BMP2). Results demonstrate that hydrolytically degradable PEG-based hydrogels are potentially useful as a delivery matrix for stem cells in regenerative medicine.     

Enzymatic degradation of monolayer for poly(lactide) revealed by real-time atomic force microscopy: effects of stereochemical structure, molecular weight, and molecular branches on hydrolysis rates

The influences of the stereochemical structure, the molecular weight, and the number of molecular branches for poly(lactide) (PLA) on enzymatic hydrolysis rates of PLA monolayers were studied by atomic force microscopy (AFM) and the Langmuir-Blodgett (LB) technique. Monolayers of six kinds of PLA with different molecular weights, stereochemical structure, and numbers of molecular branches were prepared by LB techniques and then characterized by AFM in air. The PLA molecules covered homogeneously with a silicon substrate and did not form lamellar crystals in the monolayer. We determined the initial hydrolysis rate of PLA monolayers in presence of proteinase K by volumetric analysis from the continuous AFM height images. The presence of D-lactyl unit reduced the hydrolysis rate of the monolayer. The hydrolysis rate for the linear PLLA samples increased with a decrease in the molecular weight. In contrast, the rates of erosion for branched PLLA monolayers were independent of the molecular weight of samples. The erosion rate of branched PLLA monolayers was found to be dependent on the average molecular weight of PLLA segment in branched molecules, not on the overall molecular weight of samples. From these results, furthermore, the hydrolysis mode of PLAs by proteinase K is discussed.     

In vitro and in vivo degradation of lactic acid-based interference screws used in cruciate ligament reconstruction.

Nowadays, many degradable polymers are being used under the form of interference screws to fix the bone-tendon-bone autograft in anterior cruciate ligament reconstruction. However, little is known about the post-implantation fate of these screws, especially about the formation of crystalline residues which seems to be a critical factor for the success of surgery with temporary implants based on lactic and glycolic acid derived polymers (PLAGA). In an attempt to bring in some new insights, various high molecular weight stereoregular poly(lactide)s (PLAX with X = percentage of L-lactyl units) obtained by ring-opening polymerization of lactides in the presence of zinc-metal (PLA98-Zn), zinc lactate (PLA98-Znlac) or stannous octoate (PLA100-Sn), were processed by injection-molding to make interference screws to be compared. In vivo data were collected from screws implanted in sheep knees with follow ups ranging from 6 months to 5 years. Histology confirmed the heterogeneous degradation mechanism introduced nearly 10 years ago from in vitro investigations of homemade implants having simpler geometry. The effects of the initiator system (zinc- or tin derivatives) used to polymerize the lactide monomer on the properties of injection molded interference screws was also investigated in vitro in a phosphate buffer solution at 37 degrees C. Major differences in terms of hydrophilicity, hydrolysis rate and loss of mechanical properties were observed between PLA-Zinc and PLA-Tin. Discussion of the behavior of interference screws of different compositions was made on the basis of the present understanding of PLAGA morphology and degradation characteristics.     

Formulation and Evaluation of PLA and PLGA In Situ Implants Containing Secnidazole and/or Doxycycline for Treatment of Periodontitis

The purpose of this study is to formulate in situ implants containing doxycycline hydrochloride and/or secnidazole that could be used in the treatment of periodontitis by direct periodontal intrapocket administration. Biodegradable polymers [poly (lactide) (PLA) and poly (lactide-co-glycolide) (PLGA)], each polymer in two concentrations 25%w/w, 35%w/w were used to formulate the in situ implants. The rheological behavior, in vitro drug release and the antimicrobial activity of the prepared implants were evaluated. Increasing the concentration of each polymer increases the viscosity and decreases the percent of the drugs released after 24 h. PLA implants showed a slower drugs release rate than PLGA implants in which the implants composed of 25% PLGA showed the fastest drugs release. The in vitro drug release and antimicrobial activity results were compared with results of Atridox. Results revealed that the pharmaceutical formulation based on 25% PLGA containing secnidazole and doxycycline hydrochloride has promising activity in treating periodontitis in comparison with Atridox.     

Use of short-chain cyclopentano-phosphatidylcholines to probe the mode of activation of phospholipase A2 from bovine pancreas and bee venom

A great mystery in the mechanism of phospholipase A2 (PLA2) and many other lipolytic enzymes is the "interfacial activation" induced by micellar but not monomeric substrates. Equally mysterious is the lack of interfacial activation in bee venom PLA2, as opposed to PLA2s from pancreas and other sources. We have probed these problems using the conformationally restricted short-chain cyclopentano-analogues of diacylphosphatidylcholine (Cp-DCnPC, all-trans isomer). In the reaction catalyzed by bovine pancreatic PLA2, Cp-DC8PC behaved differently from DC8PC in that its monomers and micelles showed comparable activities (but lower than the activity of DC8PC). This result suggests that the activity of PLA2 can be regulated by substrate conformation and supports the "substrate conformation model" (Wells, M. A. (1974) Biochemistry 13, 2248-2257), but raises a question as to whether Cp-DC8PC mimics monomers or micelles of DC8PC. Conformational analysis by 1H NMR revealed that monomeric Cp-DC8PC was conformationally restricted near the carbonyl region, a property characteristic of micelles. Thus, monomeric CP-DC8PC can be considered as a conformational analogue of micelles, but the important structural feature lies in the CH2COO region instead of the glycerol backbone. CP-DC8PC was then used to test a previous proposal that the bee venom PLA2 hydrolyzes monomers but not micelles (which would predict little or no activity for Cp-DC8PC since its conformation is micelle-like whether below or above its critical micelle concentration). The results showed that Cp-DC8PC is a relatively good substrate for the bee venom PLA2 in comparison with the pancreatic PLA2. This and other evidence together suggest that the bee venom PLA2 is not sensitive to the conformation of monomeric and micellar substrates and hydrolyzes both monomers and micelles. The results in both PLA2s demonstrate the usefulness of cyclopentano-phospholipids in probing the mechanism of phospholipases and the roles of substrate conformation in the catalysis of PLA2.     

Side-chain peptide-synthetic polymer conjugates via tandem "ester-amide/thiol-ene" post-polymerization modification of poly(pentafluorophenyl methacrylate) obtained using ATRP

Herein the concept of tandem postpolymerization modification as a versatile route to synthesize well-defined, highly functionalized polymers is introduced. Poly(pentafluorophenyl methacrylate) obtained by atom transfer radical polymerization was first modified with allylamine, which displaces the active ester to give well-defined polymers with pendant alkene groups, which are difficult to obtain by direct (radical) polymerization of allylic-functional monomers. The produced poly(allylmethacrylamide) was modified by a second postpolymerization modification reaction with a thiol-terminated peptide (CVPGVG) using AIBN as the radical source. NMR, IR, and SEC demonstrated successful conjugation onto the polymer to give a polymer-peptide hybrid material. This versatile strategy should extend the scope of controlled radical polymerization and "click"-type reactions.