Extrusion processing of high amylose potato starch materials

Thermoplastic starch was prepared by mixing native high amylose potato starch and normal potato starch in a Buss co-kneading extruder at starch to glycerol ratios of 100:45 and 100:30. The materials were also conditioned to different moisture contents at different relative humidities at 23 °C. After the mixing, the compounds were extruded into sheets with a Brabender laboratory extruder. The thermoplastic high amylose materials exhibited a higher melt viscosity than the normal potato starch materials when conditioned at 53% relative humidity. Increasing the moisture content in HAP from 27% to 30% (by weight) lowered the melt viscosity to the same level as that of normal potato starch with a moisture content of 28%. In general, the high amylose materials were more difficult to extrude than the thermoplastic material based on normal starch. The main extrusion problems encountered with the high amylose starch were unstable flow, insufficient melt tenacity and clogging of the die. By increasing the moisture content, increasing the compression ratio of the screw and increasing the rotation rate of the screw, the problems were reduced or eliminated. However, only with a starch to glycerol ratio of 100:45 was an acceptable extrusion result obtained. Extruded sheets of such high amylose materials had a stress at break of about 5 MPa at room temperature and 53% relative humidity, whereas the corresponding value for normal potato (thermoplastic) starch was 3 MPa. The elongation at break was also higher in the case of the high amylose material. The results are discussed in terms of residual crystallinity of the starch materials.     

Enzyme-responsive artificial chaperone system with amphiphilic amylose primer

An enzyme-responsive artificial chaperone system which employs an amphiphilic amylose primer (dodecyl maltopentaose, C12-MP) as a surfactant and phosphorylase b was designed to enable protein refolding. Effective refolding of carbonic anhydrase B after both heat denaturation (70 °C for 10 min) and guanidine hydrochloride (6 M) denaturation was observed by controlled association between the protein molecules and the C12-MP primer micelle through an enzymatic reaction.     

Synthesis of amylose acetates and amylose sulfates with high structural uniformity

Amylose triacetate (ATA) dissolved in DMSO was partially deacetylated by 1,6-hexamethylendiamine, 1,8-octamethylendiamine, 1,12-dodecylmethylendiamine and 1,2-cyclohexyldiamine (mixture of cis and trans isomers) at 80 degrees C. The reaction kinetics of the deacetylation were studied. Differences were found in the course of the reaction depending on the type of alkylene diamine (linear or cyclic). The isolated amylose acetates were dissolved in DMF and subsequently sulfated with sulfamic acid. In the course of the sulfation, the acetyl groups acted as protective groups and were completely cleaved after reaction. The amylose acetates and sulfates obtained were studied by 13C NMR spectroscopy and elemental analysis. It could be shown, that the deacetylation of ATA with the described alkylene diamines as well as the subsequent sulfation are highly regioselective. By proceeding this reaction scheme it is possible to synthesize 6-amyloseacetate, 2,6-di-amyloseacetate and 2-amylosesulfate with a high structural uniformity.     

Acetyl substitution patterns of amylose and amylopectin populations in cowpea starch modified with acetic anhydride and vinyl acetate

To study the effect of reagent type on the distribution pattern of acetyl groups in acetylated cowpea starch, amylose and amylopectin populations were isolated from the starch granules after modification to a low degree of substitution (DS < 0.1) with acetic anhydride and vinyl acetate, respectively. Slowly reacting reagent vinyl acetate resulted in higher DS values for the amylopectin populations when compared to the rapidly reacting reagent acetic anhydride. The two reagents had similar effects on the acetylation level of amylose, suggesting that the amorphous regions of granules were easily accessible for both reagents. The acetyl substitution patterns were analyzed by enzymatic degradation followed by characterization of the obtained fragments using chromatographic and mass spectrometric techniques. The distributions of acetyl groups along the amylose and amylopectin chains were more clustered for modification with vinyl acetate as compared with modification with acetic anhydride. Between the two acetylation types, pronounced differences in the acetyl substitution patterns were observed for the large fragments obtained after -amylase digestion; only slight differences were exhibited for the small fragments obtained by exhaustive enzymatic digestion of amylose and amylopectin populations.     

Formation and characterization of superparamagnetic cross-linked high amylose starch

A gelatinized cross-linked high amylose starch matrix with magnetic properties was synthesized via in situ formation of iron oxides inside the polymer matrix. Precipitation and multiple oxidation of ferrous ions were performed. The samples were observed using transmission and scanning electron microscopy, showing morphological changes in the magnetic and polymer phases. The iron content analysis revealed a decay from one oxidation cycle to the next one if no fresh ferrous solutions are added before the multiple oxidation. X-ray diffractograms, magnetization curves and Mössbauer spectra were also recorded for the characterization of the magnetic phase. The products exhibit superparamagnetic properties due to the presence of ferrimagnetic nanoparticles, although some other iron compounds are also present.     

Antisense regulation of the rice waxy gene expression using a PCR-amplified fragment of the rice genome reduces the amylose content in grain starch

The waxy gene encodes a granule-bound starch synthase. A 1.0-kb portion of the sequence of the rice waxy gene, which includes the region between exon 4 and exon 9, was inserted in an antisense orientation between the 35 S promoter and the GUS gene of pBI221. The resultant plasmid, pWXA23, was introduced into rice protoplasts by electroporation. GUS activity was clearly detected in derived callus lines, suggesting that the antisense component of the fusion gene was also expressed. Transgenic rice plants were regenerated from these callus lines and their GUS activity was confirmed. Some of the rice seeds from these transformants showed a significant reduction in the amylose content of grain starch, even though they had become polyploid. These results suggest that even when intron sequences are included, antisense constructs can bring about a reduced level of expression of a target gene. The utility of GUS, included as a reporter gene, for the simple detection of expression of an antisense gene, was apparent from these results.     

The influence of amylose on starch granule structure

Starch granules are principally composed of the two glucose polymers amylose and amylopectin. Native starch granules typically contain around 20% amylose and 80% amylopectin. However, it is possible to breed plants that produce starch with very different amylose and amylopectin contents. At present, the precise structural roles played by these two polymers are incompletely understood. In this study, small-angle X-ray scattering techniques have been applied to investigate the effect of varying amylose content on the internal structure of maize, barley and pea starch species. The results suggest that amylose disrupts the structural order within the amylopectin crystallites.     

Structural characterization of wheat starch granules differing in amylose content and functional characteristics

Small-angle X-ray scattering (SAXS) together with several complementary techniques, such as differential scanning calorimetry and X-ray diffraction, have been employed to investigate the structural features that give diverse functional properties to wheat starches (Triticum aestivum L.) within a narrow range of enriched amylose content (36–43%). For these starches, which come from a heterogeneous genetic background, SAXS analysis of duplicate samples enabled structural information to be obtained about their lamellar architecture where differences in lamellar spacing among samples were only several tenths of nanometer. The SAXS analysis of these wheat starches with increased amylose content has shown that amylose accumulates in both crystalline and amorphous parts of the lamella. Using waxy starch as a distinctive comparison with the other samples confirmed a general trend of increasing amylose content being linked with the accumulation of defects within crystalline lamellae. We conclude that amylose content directly influences the architecture of semi-crystalline lamellae, whereas thermodynamic and functional properties are brought about by the interplay of amylose content and amylopectin architecture.     

Melting behaviour of A- and B-type crystalline starch

The melting behaviour of highly crystalline spherulites, of a short chain amylose DP-15 corresponding to both the A and B polymorphs of starch has been studied as a function of water content. At water contents >40% w/w A-type spherulites melt at temperatures approximately 20°C higher than B spherulites, whilst both crystal forms melt at lower temperatures in the presence of increasing amounts of water. Using the Flory Huggins relationship for polymer crystal melting in the presence of a diluent, it is possible to predict a value for the ideal melting temperature of the dry crystals of 530 K.     

Locations of hypochlorite oxidation in corn starches varying in amylose content

The general oxidation mechanism by hypochlorite on starch has been well studied, but the information on the distribution of the oxidation sites within starch granules is limited. This study investigated the locations where the oxidation occurred within corn starch granules varying in amylose content, including waxy corn starch (WC), common corn starch (CC), and 50% and 70% high-amylose corn starch (AMC). Oxidized corn starches were surface gelatinized by 13 M LiCl at room temperature to different extents (approximately 10%, 20%, 30%, and 40%). The surface-gelatinized remaining granules were separated and studied for structural characteristics including carboxyl content, amylose content, amylopectin chain-length distribution, thermal properties, and swelling properties. Oxidation occurred mostly at the amorphous lamellae. More carboxyl groups were found at the periphery than at the core of starch granules, which was more pronounced in oxidized 70% AMC. More amylose depolymerization from oxidation occurred at the periphery of CC. For WC and CC, amylopectin long chains (>DP 36) were more prone to depolymerization by oxidation. The gelatinization properties as measured by differential scanning calorimetry also supported the changes in amylopectin fine structure from oxidation. Oxidized starches swelled to a greater extent than their unmodified counterparts at all levels of surface removal. This study demonstrates that the locations of oxidation and physicochemical properties of oxidized starches are affected by the molecular arrangement within starch granules.     

The azidation of starch

Starch is an inexpensive commodity that has been used for non-food purposes for many years. Some of these uses include cross-linked starches that are synthesized with a variety of multifunctional reagents. One unexplored possibility is the use of azides for cross-linking. To this end, azide derivatives of different starches have been synthesized, including the first reported synthesis of 6-deoxy-6-azido-amylopectin. Lithium salts, which were found to not be essential for the dissolution of starch in the reaction, were replaced with sodium azide. The time for this derivatization reaction to reach completion was determined to be 1 h. N,N-dimethylacetamide was also found to be a suitable solvent. Initial experiments suggest that the azide derivative does cross-link starch when activated by heat.     

Synthesis,biological evaluation and molecular modeling of novel thienopyrimidinone and triazolothienopyrimidinone derivatives as dual anti-inflammatory antimicrobial agents

New thienopyrimidinone and triazolothienopyrimidinone derivatives have been synthesized. These compounds were subjected to anti-inflammatory and antimicrobial activity screening aiming to identify new candidates that have dual anti-inflammatory and antimicrobial activities.Compounds 5, 7 and 10a showed minimal ulcerogenic effect and high selectivity towards human recombinant COX-2 over COX-1 enzyme. Their docking outcome correlated with their biological activity and assured the high selectivity binding towards COX-2. In addition, they could act safely up to 80 mg/kg orally or 40 mg/kg parentrally. The antimicrobial screening showed that compound 10a displayed distinctive inhibitory effect on the growth of Escherichia coli comparable to that of ampicillin. Moreover, compounds 5, 7, 9 and 12a possessed 50% of the inhibitory activity of ampicillin against E. coli. Thus, compounds 5, 7 and 10a represent promising dual acting anti-inflammatory and antimicrobial agents. This work provides rewarding template enriching the chemical space for dual anti-inflammatory anti-microbial activities.     

EPR investigation of Cu(II)-complexes with nitrogen derivatives of dialdehyde starch

Dialdehyde starch obtained by periodate oxidation from potato starch was converted into its disemicarbazone (DSC), dithiosemicarbazone (DTSC), dihydrazone (DHZ) and dioxime (DOX). The Cu(II) complexes of these compounds were prepared and characterized by Raman and EPR spectra, as well as by the measurements of magnetic susceptibility. EPR investigations showed that two types of complexes with different surroundings of copper centres existed in each starch derivative. Besides nitrogen atoms of the CN moiety and sulphur atoms of the CS moiety, also oxygen atoms from starch hydroxyl groups and/or water molecule were proposed as the coordination sites for the central copper ions.     

Genetic elimination of a starch granule protein, SGP-1, of wheat generates an altered starch with apparent high amylose

A starch granule protein, SGP-1, is a starch synthase bound to starch granules in wheat endosperm. A wheat lacking SGP-1 was produced by crossing three variants each deficient in one of three SGP-1 classes, namely SGP-A1, -B1 or -D1. This deficient wheat (SGP–1 null wheat) showed some alterations in endosperm starch, meaning that SGP-1 is involved in starch synthesis. Electrophoretic experiments revealed that the levels of two starch granule proteins, SGP-2 and -3, decreased considerably in the SGP-1 null wheat though that of the waxy protein (granule-bound starch syn- thase I) did not. The A-type starch granules were deformed. Apparent high amylose level (30.8–37.4%) was indicated by colorimetric measurement, amperometric titration, and the concanavalin A method. The altered structure of amylopectin was detected by both high- performance size-exclusion chromatography and high-performance anion exchange chromatography. Levels of amylopectin chains with degrees of polymerization (DP) 6–10 increased, while DP 11–25 chains decreased. A low starch crystallinity was shown by both X-ray diffraction and differential scanning calorimetry (DSC) analyses because major peaks were absent. Abnormal crystallinity was also suggested by the lack of a polarized cross in SGP-1 null starch. The above results suggest that SGP-1 is responsible for amylopectin synthesis. Since the SGP-1 null wheat produced novel starch which has not been described before, it can be used to expand variation in wheat starch. Received: 30 April 1999 / Accepted: 9 November 1999     

Effects of acid hydrolysis and defatting on crystallinity and pasting properties of freeze-thawed high amylose corn starch

Paste of defatted and/or mildly acid-hydrolyzed high amylose corn starch was freeze-thawed, and then the starch was isolated by vacuum drying for the analysis in crystallization and pasting properties. X-ray diffraction pattern and differential scanning calorimetric analysis showed that the crystallinity of the freeze-thawed starch was increased as the degree of hydrolysis increased. The diffraction pattern revealed B- and V-crystals with patterns with diffraction peaks at 17, 20, and 23–25° (2θ), which were developed by amylose recrystallization during the freeze-thawing. The crystal melting enthalpies, for dual endothermic transitions above 100 °C, which resulted from the melting of amylose–lipids complex and amylose double helices were raised by the treatment. The isolated and dried starch formed a paste by aqueous heating under the ambient pressure, and its paste viscogram exhibited substantially higher resistance to shear-thinning, and rapid setback upon cooling. Acid hydrolysis, however, reduced overall paste viscosity, possibly due to the increased crystallinity. Enzyme-resistant starch content in the acid hydrolyzed starch was increased by the freeze-thawing, but not by acid hydrolysis. It was slightly increased by defatting.     

Structural parameters of amylopectin clusters and semi-crystalline growth rings in wheat starches with different amylose content

Small-angle X-ray scattering (SAXS) and scanning electron microscopy (SEM) were used to investigate the internal structure of wheat starch granules with different amylose content. Different approaches were used for treatment (interpretation) of SAXS data to assess the values of structural parameters of amylopectin clusters and the size of crystalline and amorphous lamella in different wheat starches. The average values of the semi-crystalline growth rings thickness in starches have been determined and the relationship between structural characteristics and thermodynamic melting parameters is discussed.     

Determination of the DS and substituent distribution of cationic alkyl polyglycosides and cationic starch ethers by GLC after dealkylation with morpholine

The total DS and substituent distribution of starch and alkyl polyglycosides functionalised as O-(2-hydroxy-3-trimethylammonium)propyl ethers were determined by GLC. To achieve volatile analytes, the samples were submitted to methanolysis, N-demethylation and O-trimethylsilylation. Alternatively hydrolysis, reduction with NaBH(4) and subsequent O-acetylation were performed, but suffered from intramolecular acetal formation of 2-O-substituted residues, preventing reduction. Morpholine as nucleophile was superior to thiophenolate with regard to quantitative dealkylation and side product formation. The ratio of un-, mono-, di-, tri-, and tetrasubstituted compounds was determined. The total DS values calculated from these mole fractions were in good agreement with those obtained from elemental analysis or NMR from standards. Regioselectivity of the cationisation reaction was determined after methanolysis, permethylation and Hofmann elimination by GLC.     

Effect of amylose deposition on potato tuber starch granule architecture and dynamics as studied by lintnerization

The effect of amylose deposition on the amylopectin crystalline lamellar organization in potato starch granules was studied by mild acid, so‐called lintnerization, of potato tuber starch transgenically engineered to deposit different levels of amylose. The starch granules were subjected to lintnerization at different temperatures (25, 35, and 45°C) and to two levels of solubilization, ～ 45 and 80%. The rate of the lintnerization increased with temperature but was suppressed by amylose. The molecular size of the lintner dextrins increased with temperature, but this effect was suppressed by the presence of amylose. At high temperatures and low‐amylose content, the degree of branches was high with the concomitant increase in size in the dextrins. A portion of the branches was resistant to debranching enzymes possibly due to specific structural formations. The effects of temperature suggested a unique granular architecture of potato starch, and a model showing the dependence of temperature on the dynamic arrangement of amylopectin and amylose in the crystalline and amorphous lamellae for the potato starch is suggested. © 2012 Wiley Periodicals, Inc.     

Effect of sulfate and citrate salts on derivatization of amylose and amylopectin during hydroxypropylation of corn starch

Common corn starch was modified in 0.56 M sodium sulfate solution and in 0.31 M potassium citrate solution. It was found that about 1.8 times the amount of reagent (propylene oxide) was needed to get a same molar substitution (MS) when potassium citrate was used. Hydroxypropylated starches were fractionated on a size-exclusion column to separate amylose from amylopectin, and MS values of the whole starch, the amylose, and the amylopectin were determined. In all preparations, amylose was derivatized to a greater extent than was amylopectin. The data indicate that, with common corn starch: (1) the greater the overall derivatization, the greater was the preference for derivatization of amylose; and (2) the preference for amylose derivatization was greater for corn starch modified in potassium citrate solution than in sodium sulfate solution when the MS values for the two preparations were essentially the same.