Decoloration of chitosan by UV irradiation

Decoloration of chitosan by UV irradiation, which was used to replace a bleaching step during chitosan preparation, was evaluated under four separate treatments (effect of irradiation time, chitosan/water ratio, stirring speed, and UV light source). The optimal decoloration condition was defined as that producing white chitosan with higher viscosity. Decoloration of chitosan could be achieved effectively using a UV-C light by stirring unbleached chitosan in water (1:8, w/v) for 5 min at 120 rpm. UV irradiation applied under the optimal conditions could be used to produce chitosan with desirable white color (L^* = 76.95, a^* = −0.37, and b^* = 14.04) and high viscosity (1301.7 mPa s at 0.5% w/v in 1.0% v/v acetic acid).     

Preparation and anticoagulant activity of a low-molecular-weight sulfated chitosan

Synthesis of chitosan sulfates with low molecular weight (M_v 9000–35,000 Da) was carried out by sulfation of low molecular weight chitosan (M_v 10,000–50,000 Da). The oleum was used as sulfating agent and dimethylfornamide as medium. The chitosans were prepared by enzymatic and acidic hydrolysis of initial high molecular weight chitosan as well as by extrusion solid-state deacetylation of chitin. As was shown by FT-IR and NMR-methods and elemental analysis, the sulfation occurred at C-6 and C-3 positions and substitution degree is 1.10–1.63. The molecular weight sulfated chitosan was determined by viscometric method and the Mark–Houwink equation [η]=10⁻⁵ 4.97 M^0.77. Study of anticoagulant activity showed that chitosan sulfates with lowered molecular weight demonstrated a regular increase of anti-Xa activity like heparins.     

Effect of molecular weight of chitosan with the same degree of deacetylation on the thermal, mechanical, and permeability properties of the prepared membrane

Different molecular weight, 90% deacetylated chitosans were obtained by ultrasonic degradation on 90% deacetylated chitosan at 80 °C for various times.

Ninety percent deacetylated chitosan was prepared from alkali treatment of chitin that was obtained from red shrimp waste. Number average-, viscosity average- molecular weights were measured by gel permeation chromatography and the viscometric method, respectively. Degree of deacetylation was measured by the titration method. Enthalpy, maximum melting temperature, tensile strength and elongation of the membranes, flow rate of permeates and water are properties measured to elucidate the effect of molecular weight of chitosan on the above thermal, mechanical, and permeation properties, respectively of the prepared membranes. Results show tensile strength, tensile elongation, and enthalpy of the membrane prepared from high molecular weight chitosans were higher than those from low molecular weight. However, the permeability show membranes prepared from high molecular weight chitosans are lower than that from those of low molecular weight.     

Physicochemical characterization of chitin and chitosan from crab shells

Crab chitosan was prepared by alkaline N-deacetylation of crab chitin for 60, 90 and 120 min and the yields were 30.0-32.2% with that of chitosan C120 being the highest. The degree of N-deacetylation of chitosans (83.3–93.3%) increased but the average molecular weight (483–526 kDa) decreased with the prolonged reaction time. Crab chitosans showed lower lightness and WI values than purified chitin, chitosans CC and CS but higher than crude chitin. With the prolonged reaction time, the nitrogen (8.9–9.5%), carbon (42.2–45.2%) and hydrogen contents (7.9–8.6%) in chitosans prepared consistently increased whereas N/C ratios remained the same (0.21). Crab chitosans prepared showed a melting endothermic peak at 152.3–159.2 °C. Three chitosans showed similar microfibrillar crystalline structure and two crystalline reflections at 2θ = 8.8–9.0° and 18.9–19.1°. Overall, the characteristics of three crab chitosans were unique and differed from those of chitosan CC and CS as evidenced by the element analysis, differential scanning calorimetry, scanning electron microscopy and X-ray diffraction patterns.     

Proteinase inhibitor synthesis in tomato leaves : induction by chitosan oligomers and chemically modified chitosan and chitin

Soluble chemical derivatives of chitin and chitosan including ethylene glycol chitin, nitrous acid-modified chitosan, glycol chitosan, and chitosan oligomers, produced from chitosan by limited hydrolysis with HCl, were found to possess proteinase inhibitor inducing activities when supplied to young excised tomato (Lycopersicon esculentum var Bonnie Best) plants. Nitrous acid-modified chitosans and ethylene glycol chitin exhibited about 2 to 3 times the activity of acid hydrolyzed chitosan and 15 times more activity than glycol chitosan. The parent chitin and chitosans are insoluble in water or neutral buffers and cannot be assayed. Glucosamine and its oligomers from degree of polymerization = 2 through degree of polymerization = 6 were purified from acid-fragmented chitosan and assayed. The monomer was inactive and dimer and trimer exhibited weak activities. Tetramer possessed higher activity and the larger pentamer and hexamer oligomers were nearly as active as the total hydrolyzed mixture. None of the fragments exhibited more than 2% acetylation (the limits of detection). The contents of the acid-fragmented mixture of oligomers was chemically N-acetylated to levels of 13% and 20% and assayed. The N-acetylation neither inhibited nor enhanced the proteinase inhibitor inducing activity of the mixture. These results, along with recent findings by others that chitinases and chitosanases are present in plants, provide further evidence for a possible role of soluble chitosan fragments as signals to activate plant defense responses.     

Extraction of chitin and chitosan from housefly,Musca domestica,pupa shells

Chitins and chitosans are some of the most abundant natural polysaccharide materials, and are used to increase innate immune response and disease resistance in humans and animals. In this work, chitin and chitosan from housefly, Musca domestica, pupa shells were obtained by treatment with HCl and NaOH. For chitin extraction, 2 N HCl and 1.25 N NaOH solutions were used to achieve decalcification and deproteinization, respectively. For chitosan extraction, 50% NaOH solution was used to achieve deacetylation. The yields of chitin and chitosan from pupa shells of M. domestica were 8.02% and 5.87%, respectively. The deacetylations of chitosan (from chitin C1 and C2) were 89.76% and 92.39%, respectively, after the first alkali treatment with 50% NaOH (w/w) solution at 105 °C for 3 h and 5 h, respectively. The viscosities of the chitosans (from chitin C1 and C2) were 33.6 and 19.2 cP, respectively.     

TEMPO-mediated oxidation of chitin, regenerated chitin and N-acetylated chitosan

A commercial chitin, regenerated chitin prepared from chitin solutions in 6.8% NaOH and N-acetylated chitosans with degrees of N-acetylation (DNAc) of 77–93% were subjected to oxidization in water with NaClO and catalytic amounts of 2,2,6,6-tetramethylpiperidinyloxy radical (TEMPO) and NaBr. When regenerated chitin with DNAc of 87% and N-acetylated chitosan with DNAc of 93% were used as starting materials, water-soluble β-1,4-linked poly-N-acetylglucosaminuronic acid (chitouronic acid) Na salts with degrees of polymerization of ca. 300 were obtained quantitatively within 70 min. On the other hand, the original chitin and N-acetylated chitosan with DNAc of 77% did not give water-soluble products, owing to incomplete oxidation. The high crystallinity of the original chitin brought about low reactivity, and the high C2-amino group content of the N-acetylated chitosan with DNAc of 77% led to degradations rather than the selective oxidation at the C6 hydroxyls. The obtained chitouronic acid had low viscosities in water, and clear biodegradability by soil microorganisms.     

Preparation of low molecular weight chitosan using solution plasma system

The solution plasma system was introduced to treat chitosan solution in order to prepare low molecular weight chitosan. The plasma treatment time was varied from 0 min to 300 min. The plasma-treated chitosan was characterized including viscosity, molecular weight by GPC, and chemical characteristics by FT-IR. The results showed that after treated with plasma for 15-60 min, the viscosity of chitosan solution and apparent molecular weight of chitosans were remarkably decreased, compared to those of untreated sample. Longer treatment time had less effect on both viscosity and molecular weight of samples. Eventually, long treatment time (≥180 min) showed no influence on both viscosity and apparent molecular weight. This suggested that the degradation process of chitosan occurred during plasma treatment. FT-IR analysis revealed that chemical structure of chitosan was not affected by solution plasma treatment. TOF-MS results showed that chitooligosaccharides with the degree of polymerization of 2-8 were also generated by solution plasma treatment. The results suggested that solution plasma system could be a potential method for the preparation of low molecular weight chitosan and chitooligosaccharides.     

N-Deacetylation and depolymerization reactions of chitin/chitosan: Influence of the source of chitin

The deacetylation and depolymerization reactions of chitin/chitosan from three crustacean species (Paralomis granulosa, Lithodes antarcticus and Palinurus vulgaris) were evaluated under the same conditions. The average molecular weight and the mole fraction of N-acetylated units were the parameters studied in the resulting chitosans. During the N-deacetylation process P. granulosa, L. antarcticus and P. vulgaris follow a pseudo-first order kinetics and their apparent rate constants are very similar. However, the degradation rate of chitosan in the first 45 min of this process is higher for P. vulgaris. The depolymerization process follows a pseudo-first order kinetics for the three species, but in the first 9 min P. vulgaris shows a slightly lower depolymerization rate. Hence, depending on the ash contents, crystallinity and the physicochemical characteristics of chitin from these sources, the obtained chitosans show different qualities.     

Antitumor activity of chitosan from mayfly with comparison to commercially available low,medium and high molecular weight chitosans

Insects’ cuticles have a potential to be evaluated as a chitin source. Especially adults of aquatic insects like mayflies (order Ephemeroptera) swarm in enormous numbers in artificially lit areas while mating in spring and then die by leaving huge amounts of dead insects’ bodies. Here in this study, mayfly corpses were harvested and used for production of low MW chitosan. Dried mayfly bodies had 10.21% chitin content; mayfly chitin was converted into chitosan with efficiency rate of 78.43% (deacetylation degree, 84.3%; MW, 3.69 kDa). Cytotoxicity and anti-proliferative activity of mayfly and commercially available shrimp chitosans (low, medium, and high MW) were determined on L929 fibroblast and three different cancer types including HeLa, A549, and WiDr. Apoptosis and necrosis stimulating potential of mayfly and commercial chitosans were also evaluated on A549 and WiDr cells using acridine orange and propidium iodide dual staining to observe morphological changes in nuclei and thus to reveal the predominant cell death mechanism. The effects of chitosans have varied depending on cell types, concentration, and chitosan derivatives. Mayfly and low MW chitosans had a cytotoxic effect at a concentration of 500 μg mL^?1 on non-cancer cells. At concentrations below this value (250 μg mL^?1), mayfly and commercial chitosans except high MW one exhibited strong inhibitory activity on cancer cells especially A549 and WiDr cells. Mayfly chitosan induced early and late apoptosis in A549 cells, but late apoptosis and necrosis in WiDr cells. This study suggests that dead bodies of mayflies can be used for production of low MW chitosan with anti-proliferative activity.     

Effect of ultrasonic treatment on the biochemphysical properties of chitosan

Four chitosans with different molecular weights and degrees of deacetylation degree and 28 chitosans derived from these initial chitosans by ultrasonic degradation have been characterized by gel permeation chromatography (GPC), FT-IR spectroscopy, X-ray diffraction and titrimetric analyses. Antimicrobial activities were investigated against E. coli and S. aureus using an inhibitory rate technique. The results showed that ultrasonic treatment decreased the molecular weight of chitosan, and that chitosan with higher molecular weight and higher DD was more easily degraded. The polydispersity decreased with ultrasonic treatment time, which was in linear relationship with the decrease of molecular weight. Ultrasonic degradation changed the DD of initial chitosan with a lower DD (<90%), but not the DD of the initials chitosan with a higher DD (>90%). The increased crystallinity of ultrasonically treated chitosan indicated that ultrasonic treatment changed the physical structure of chitosan, mainly due to the decrease of molecular weight. Ultrasonic treatment enhanced the antimicrobial activity of chitosan, mainly due to the decrease of molecular weight.     

A morphological study of heavy metal complexes of chitosan and crosslinked chitosans by SEM and WAXRD

Metal complexes of salts of Hg, Cu, Cd, Pb, Zn, and Mn with chitosan and crosslinked chitosans were prepared, and their morphologies were studied using scanning electron microscopy and wide angle X-ray diffraction. The metal ions which were specifically and strongly complexed to the amino functions of chitosans, like Hg, showed smooth surface morphology inspite of large number of ions complexed (372 mg/g of chitosan). The presence of metal ions on the surface of the chitosans could be detected with decrease in metal ion binding, in the following sequence Hg > Cu > Cd > Zn > Pb > Mn. Particularly in the case of Pb ions, the presence of these ions is clearly seen on the surface of the polymer by SEM. The number of ions of Mn complexed on the polymers was too few (5 mg/g of chitosan) to be visible. SEM of Hg and Cu complexes do not show the “holes” observed in the crosslinked polymers as they bind specifically to amino groups of chitosan, but for Cd, Zn, Mn, and Pb complexes, these “holes” are clearly visible. These results are also in agreement with the morphologies studied by WAXRD. The metal complexation data for each of these metal ions was also in the same sequence.     

The co-ordination of chitosan and chitin synthesis in Mucor rouxii

Chitin synthetase preparations from cell walls and chitosomes of the fungus Mucor rouxii were tested for their ability to synthesize chitosan when incubated with uridine diphosphate N-acetyl-D-glucosamine in the presence of chitin deacetylase. The most effective chitin synthetase preparation was one dissociated from cell walls with digitonin. The rate of chitosan synthesis by the wall-dissociated chitin synthetase was about three times that of an equivalent amount of cell walls. The chitosan-synthesizing ability of chitosomes was relatively low, but was more than tripled by treatment with digitonin. Presumably, digitonin improves chitosan yields of dissociating chitin synthetase. The dissociated enzyme would produce dispersed chitin chains that could be attacked by chitin deacetylase before they have time to crystallize into microfibrils. The regulation of chitin and chitosan syntheses in vivo may be determined by the organization of chitin synthetase molecules at the cell surface. Those molecules that remain organized as a complex, similar if not identical to that found in chitosomes, would produce mainly chitin. Chitosan would be preferentially produced by chitin synthetase molecules which are dispersed upon reaching the cell surface.     

Studies on chitosan: 3. Evidence for the presence of random and block copolymer structures in partially N-acetylated chitosans

The chemical structures of moderately N-deacetylated chitosans (MDC) derived from chitin under heterogeneous reaction conditions and partially N-acetylated chitosans (PAC) derived from highly N-deacetylated chitosans (HDC) under homogeneous reaction conditions were deduced from the data of the stability of their solutions in alkaline media, the swelling behaviour and X-ray diffraction patterns of their films in connection with the degree of N-acetylation of them. The solutions of PAC with more than 51% acetyl content, which were prepared from HDC by N-acetylation, were stable and remained clear and homogeneous by adding 1.2 equivalents of NaOH. On the contrary the solutions of PAC with more than 52% acetyl content, which were prepared from MDC, became turbid by neutralization with less than 1.15 equivalents of NaOH. The films of PAC prepared from HDC were highly swollen in water. The degree of swelling of the chitosan film with 51% acetyl content, prepared from the 6% acetyl content chitosan, was 121% while that of the 53% acetyl content chitosan, prepared from the 30% acetyl content chitosan, was 28%. From these data it was possible to set up a hypothesis that PAC prepared from HDC were considered as random-type copolymers of N-acetyl-glucosamine and glucosamine units whereas MDC were considered as block-type copolymers.     

Molecular weight distribution of chitosan isolated from Mucor rouxii under different culture and processing conditions

The isolation of chitosan from a fungal source offers the potential of a product with controlled physicochemical properties not obtainable by the commercial chemical conversion of crustacean chitin. A variety of culture and processing protocols using Mucor rouxii were studied for their effects on biomass yield and chitosan molecular weight. Weight-averaged molecular weight determined by gel permeation chromotography ranged from 2.0 x 10(5) to approximately 1.4 x 10(6) daltons. The chitosan yield ranged from 5% to 10% of total biomass dry weight and from 30% to 40% of the cell wall. Of the culture parameters studied, length of incubation and medium composition effected biomass production and molecular weight. Modification of the processing protocol, including the type and strength of acid, and cell wall disruption in acid prior to refluxing were used to optimize the efficiency of chitosan extraction.The degree of deacetylation of fungal and commercial chitosans was compared using infrared spectrometry, titration, and first derivative of UV absorbance spectrometry. The chitosan obtained directly from the fungal cell wall had a higher degree of deacetylation than commercial chitosan from the chemical conversion process.     

Production and conversion of chitosan with cultures of Mucor rouxii or Phycomyces blakesleeanus

Summary Highly deacetylated chitosan was accumulated in the mycelia ofMucor rouxii orPhycomyces blakesleeanus. These cultures also effected the deacetylation of the chitin ofAspergillus niger mycelium into chitosan. After 96 hours of incubation with these cultures the degree of acetylation of commercial crab shell chitosan was reduced from 25.0% to values between 4.3 and 8.6%. The potential exists for the production of chitosans with tailored physico-chemical properties from waste chitin.     

Antioxidant properties of chitosan from crab shells

Crab chitosan was prepared by alkaline N-deacetylation of crab chitin for 60, 90 and 120 min and its antioxidant properties studied. Chitosan exhibited showed antioxidant activities of 58.3–70.2% at 1 mg/mL and showed reducing powers of 0.32–0.44 at 10 mg/mL. At 10 mg/mL, the scavenging ability of chitosan C60 on 1,1-diphenyl-2-picrylhydrazyl radicals was 28.4% whereas those of other chitosans were 46.4–52.3%. At 0.1 mg/mL, scavenging abilities on hydroxyl radicals were 62.3–77.6% whereas at 1 mg/mL, chelating abilities on ferrous ions were 82.9–96.5%. All EC₅₀ values of antioxidant activity were below 1.5 mg/mL. With regard to antioxidant properties assayed, the effectiveness of chitosans C60, C90 and C120 correlated with their N-deacetylation times. Overall, crab chitosan was good in antioxidant activity, scavenging ability on hydroxyl radicals and chelating abilities on ferrous ions and may be used as a source of antioxidants, as a possible food supplement or ingredient in the pharmaceutical industry.     

VESICLE SIZE,SIZE DISTRIBUTION,STABILITY, AND RHEOLOGICAL PROPERTIES OF LIPOSOMES COATED WITH WATER-SOLUBLE CHITOSANS OF DIFFERENT MOLECULAR WEIGHTS AND CONCENTRATIONS

The objectives of this study were to explore the effects of coating with water-soluble chitosans of different molecular weights and concentrations on vesicle size, size distribution, stability, and apparent viscosity of liposomes. The results indicate that the vesicle size of liposomes coated with different concentrations and different molecular weights of water-soluble chitosans decreased with increasing passes of microfluidizing treatment, then reached a constant value. Liposomes subjected to the same microfluidization treatment were larger for those coated with a higher concentration (of the same molecular weight chitosan) or coated with a lower molecular weight (at the same concentration) of water-soluble chitosans. The average particle size of liposomes coated with different molecular weights of water-soluble chitosans decreased with increasing number of passes of microfluidizing treatment. The apparent viscosity of liposomes coated with water-soluble chitosans decreased after the first pass, then reached a constant value after the third pass of microfluidizing treatment. Apparent viscosities of liposomes subjected to different passes of microfluidization treatment were larger for those coated with a higher concentration or a higher molecular weight of water-soluble chitosans. Liposomes coated with 0.5% of different molecular weights of water-soluble chitosans behaved as pseudoplastic fluids. At the same shear rate, the apparent viscosities of liposomes subjected to more passes of microfluidizing treatment were larger than those subjected to fewer passes of microfluidizing treatment. Liposomes coated with water-soluble chitosans are more stable than those without a coating.     

Reactions of chitosan: 4. Preparation of organosoluble derivatives of chitosan

Fully subtituted di-O-acetyl-N-acetylchitosan (chitin diacetate) has been prepared by a route in which the hydroxyl groups are acetylated prior to N-acetylation. This overcomes the previously reported intramolecular steric hindrance to esterification caused by the N-acetamido group. The resultant products were of high viscosity but had a limited solubility range. Di-O-acrylcarbamate derivatives of N-acetylchitosan (chitin) have been produced by a similar route, whilst di-O-arylcarbamate-N-arylureidochitosans have been prepared directly from chitosan. These products also have limited solubility ranges and have inherent viscosities similar to that of di-O-acetylchitosan prepared from the same batch of chitosan.     

High yield production of monomer-free chitosan oligosaccharides by pepsin catalyzed hydrolysis of a high deacetylation degree chitosan

The high molecular weight of chitosan, which results in a poor solubility at neutral pH values and high viscosity aqueous solutions, limits its potential uses in the fields of food, health and agriculture. However, most of these limitations are overcome by chitosan oligosaccharides obtained by enzymatic hydrolysis of the polymer. Several commercial enzymes with different original specificities were assayed for their ability to hydrolyze a 93% deacetylation degree chitosan and compared with a chitosanase. According to the patterns of viscosity decrease and reducing end formation, three enzymes--cellulase, pepsin and lipase A--were found to be particularly suitable for hydrolyzing chitosan at a level comparable to that achieved by chitosanase. Unlike the appreciable levels of both 2-amino-2-deoxy-D-glucose and 2-acetamido-2-deoxy-D-glucose monomers released from chitosan by the other enzymes after a 20h-hydrolysis (4.6-9.1% of the total product weight), no monomer could be detected following pepsin cleavage. As a result, pepsin produced a higher yield of chitosan oligosaccharides than the other enzymes: 52% versus as much as 46%, respectively. Low molecular weight chitosans accounted for the remaining 48% of hydrolysis products. The calculated average polymerization degree of the products released by pepsin was around 16 units after 20h of hydrolysis. This product pattern and yield are proposed to be related to the bond cleavage specificity of pepsin and the high deacetylation degree of chitosan used as substrate. The optimal reaction conditions for hydrolysis of chitosan by pepsin were 40 degrees C and pH 4.5, and an enzyme/substrate ratio of 1:100 (w/w) for reactions longer than 1h.