Simultaneous nitrogen and carbon removal in a single chamber microbial fuel cell with a rotating biocathode

In this study, a single chamber microbial fuel cell (MFC) with a rotating biocathode is developed to simultaneously remove chemical oxygen demand (COD) and nitrogen accompanying current production. Under continuous regime with a feeding COD/N ratio of 5:1, removal efficiencies of total organic carbon (TOC) and total nitrogen (TN) were 85.7 ± 7.4% and 91.5 ± 7.2%, respectively, and a maximum power output of 585 mW m^?3 was yielded. In the batch tests, TN removal efficiencies for closed/open circuit were 82.1 ± 0.5% and 59.4 ± 3.3%, respectively. Cyclic voltammetry measurements demonstrated that the biocathode could efficiently catalyze nitrate reduction reaction. Autotrophic denitrification facilitated nitrogen removal using the electrode as electron donor. 16S rRNA-denaturing gradient gel electrophoresis (DGGE) was employed for community fingerprinting. At the biocathode the bacteria involved in nitrogen cycle predominated, of which the denitrifying bacteria were closely similar to Acidovorax sp. and/or Delftia sp. They were affiliated with the family Comamondaceae. The combination of rotating biological contactors with MFCs derives a promising opportunity for wastewater treatment with a low cost and high quality effluent.     

Autotrophic nitrite removal in the cathode of microbial fuel cells

Nitrification to nitrite (nitritation process) followed by reduction to dinitrogen gas decreases the energy demand and the carbon requirements of the overall process of nitrogen removal. This work studies autotrophic nitrite removal in the cathode of microbial fuel cells (MFCs). Special attention was paid to determining whether nitrite is used as the electron acceptor by exoelectrogenic bacteria (biologic reaction) or by graphite electrodes (abiotic reaction). The results demonstrated that, after a nitrate pulse at the cathode, nitrite was initially accumulated; subsequently, nitrite was removed. Nitrite and nitrate can be used interchangeably as an electron acceptor by exoelectrogenic bacteria for nitrogen reduction from wastewater while producing bioelectricity. However, if oxygen is present in the cathode chamber, nitrite is oxidised via biological or electrochemical processes. The identification of a dominant bacterial member similar to Oligotropha carboxidovorans confirms that autotrophic denitrification is the main metabolism mechanism in the cathode of an MFC.     

Simultaneous carbon and nitrogen removal from piggery wastewater using loop configuration microbial fuel cell

Simultaneous carbon and nitrogen removal using loop configuration microbial fuel cell (MFC) with relatively large size of 5 L was investigated in this study. Four MFC reactors were constructed with a loop configuration to eliminate the pH gradient, and the reactor performance was examined with different separators and cathode materials. The performance of the reactors in terms of electricity generation and contaminant removal rate was examined. Results showed that a maximum power density of 1415.6 mW/m³ (The empty bed volume of anode chamber) was obtained at a current density of 3258.5 mA/m³ with cation exchange membrane as separator and graphite felt (Pt coated) as cathode using the piggery wastewater as feed, and the organic removal rate obtained was approximately 0.523 kg COD/m³/d (total anode chamber) with nitrogen removal rate of 0.194 kg N/m³/d (total cathode chamber).     

Simultaneous organics removal and bio-electrochemical denitrification in microbial fuel cells

Simultaneous organics removal and bio-electrochemical denitrification using a microbial fuel cell (MFC) reactor were investigated in this study. The electrons produced as a result of the microbial oxidation of glucose in the anodic chamber were transferred to the anode, which then flowed to the cathode in the cathodic chamber through a wire, where microorganisms used the transferred electrons to reduce the nitrate. The highest power output obtained on the MFCs was 1.7 mW/m(2) at a current density of 15 mA/m(2). The maximum volumetric nitrate removal rate was 0.084 mg NO(3)(-)-N cm(-2) (electrode surface area) day(-1). The coulombic efficiency was about 7%, which demonstrated that a substantial fraction of substrate was lost without current generation.     

Application of biocathode in microbial fuel cells: cell performance and microbial community

Instead of the utilization of artificial redox mediators or other catalysts, a biocathode has been applied in a two-chamber microbial fuel cell in this study, and the cell performance and microbial community were analyzed. After a 2-month startup, the microorganisms of each compartment in microbial fuel cell were well developed, and the output of microbial fuel cell increased and became stable gradually, in terms of electricity generation. At 20 ml/min flow rate of the cathodic influent, the maximum power density reached 19.53 W/m3, while the corresponding current and cell voltage were 15.36 mA and 223 mV at an external resistor of 14.9 Omega, respectively. With the development of microorganisms in both compartments, the internal resistance decreased from initial 40.2 to 14.0 Omega, too. Microbial community analysis demonstrated that five major groups of the clones were categorized among those 26 clone types derived from the cathode microorganisms. Betaproteobacteria was the most abundant division with 50.0% (37 of 74) of the sequenced clones in the cathode compartment, followed by 21.6% (16 of 74) Bacteroidetes, 9.5% (7 of 74) Alphaproteobacteria, 8.1% (6 of 74) Chlorobi, 4.1% (3 of 74) Deltaproteobacteria, 4.1% (3 of 74) Actinobacteria, and 2.6% (2 of 74) Gammaproteobacteria.     

Use of inexpensive semicoke and activated carbon as biocathode in microbial fuel cells

In this study, two inexpensive semicoke and activated carbon packed bed biocathode were developed for oxygen reduction in microbial fuel cells (MFCs). These two materials were compared with two commonly used biocathode materials graphite and carbon felt in terms of material characteristic, power density, biomass density and price-performance ratio. MFCs with semicoke and activated carbon biocathode produced a maximum power density of 20.1 W/m3 (normalized liquid volume in cathodic compartment) and 24.3 W/m3, respectively, compared to 14.1 and 17.1 W/m3 obtained by MFCs with graphite and carbon felt biocathode, respectively. The bacteria attached on biocathode played a major role in oxygen reduction for all the materials investigated. The material cost per Watt produced for semicoke and activated carbon biocathode is only 2.8% and 22.7% of that for graphite biocathode, respectively. These two inexpensive carbon materials, especially semicoke, are very cost-effective biocathode materials for future large scale MFCs.     

Electron transfer mechanisms, new applications, and performance of biocathode microbial fuel cells

Broad application of microbial fuel cells (MFCs) requires low cost and high operational sustainability. Microbial-cathode MFCs, or cathodes using only bacterial catalysts (biocathodes), can satisfy these demands and have gained considerable attention in recent years. Achievements with biocathodes over the past 3-4 years have been particularly impressive not only with respect to the biological aspects but also the system-wide considerations related to electrode materials and solution chemistry. The versatility of biocathodes enables us to use not only oxygen but also contaminants as possible electron acceptors, allowing nutrient removal and bioremediation in conjunction with electricity generation. Moreover, biocathodes create opportunities to convert electrical current into microbially generated reduced products. While many new experimental results with biocathodes have been reported, we are still in the infancy of their engineering development. This review highlights the opportunities, limits, and challenges of biocathodes.     

Sustainable power production in a membrane-less and mediator-less synthetic wastewater microbial fuel cell

Microbial fuel cells (MFCs) fed with wastewater are currently considered a feasible strategy for production of renewable electricity.     

Time-course correlation of biofilm properties and electrochemical performance in single-chamber microbial fuel cells

The relationship between anode microbial characteristics and electrochemical parameters in microbial fuel cells (MFCs) was analyzed by time-course sampling of parallel single-bottle MFCs operated under identical conditions. While voltage stabilized within 4 days, anode biofilms continued growing during the six-week operation. Viable cell density increased asymptotically, but membrane-compromised cells accumulated steadily from only 9% of total cells on day 3 to 52% at 6 weeks. Electrochemical performance followed the viable cell trend, with a positive correlation for power density and an inverse correlation for anode charge transfer resistance. The biofilm architecture shifted from rod-shaped, dispersed cells to more filamentous structures, with the continuous detection of Geobacter sulfurreducens-like 16S rRNA fragments throughout operation and the emergence of a community member related to a known phenazine-producing Pseudomonas species. A drop in cathode open circuit potential between weeks two and three suggested that uncontrolled biofilm growth on the cathode deleteriously affects system performance.     

双阳极室甲烷微生物燃料电池同步脱氮除硫性能及微生物群落分析

【背景】甲烷厌氧氧化(anaerobic oxidation of methane, AOM)包含反硝化型甲烷厌氧氧化和硫酸盐还原型甲烷厌氧氧化。目前,人们向水体中排放过量的含氮及含硫污染物,引起了严重的环境污染和生态破坏。【目的】利用甲烷厌氧氧化微生物燃料电池(microbial fuel cell, MFC)研究同步脱氮除硫耦合反应机理及反应过程中微生物的多样性信息。【方法】构建了3个微生物燃料电池(N-S-MFC、N-MFC、S-MFC),以甲烷作为唯一碳源,探究其同步脱氮除硫性能,并采用16S rRNA基因高通量测序技术对微生物群落结构进行分析。【结果】N-S-MFC中硝酸盐和硫酸盐的去除率分别为90.91%和18.46%。阳极室中微生物的相对丰度提高,与反硝化及硫酸盐还原菌相关的微生物大量富集,如门水平上拟杆菌门(Bacteroidota)、厚壁菌门(Firmicutes)和脱硫杆菌门(Desulfobacterota),同时属水平上Methylobacterium＿Methylorubrum、Methylocaldum、Methylomonas等常见的甲烷氧化菌增多。【结论...     

Analysis of microbial diversity in oligotrophic microbial fuel cells using 16S rDNA sequences

Molecular ecological techniques were applied to analyze the bacterial diversity of two oligotrophic microbial fuel cells (MFCs) enriched using river water or artificial wastewater (AWW) as fuel. Denaturing gradient gel electrophoresis (DGGE) of the PCR amplified 16S rDNA showed that different microbial communities were present in the two MFCs and these were different from the river sediment used to initiate the enrichment. Nearly complete 16S rDNA was amplified and sequenced. Over 80% of the clones were Proteobacteria. Betaproteobacteria were the dominant clones (46.2%) in MFCs fed with river water, and about 64.4% of the clones in MFCs fed with AWW were Alphaproteobacteria. Actinobacteria were found only in the MFC fed with AWW, and Deltaproteobacteria, Acidobacteria, Chloroflexi and Verrucomicrobia in the MFC fed with river water. Many clones were related to uncultured bacteria, some with homology less than 95%, indicating that many novel bacteria were enriched in the oligotrophic MFCs.     

Removal of selenite from wastewater using microbial fuel cells

Simultaneous electricity generation and selenium removal was evaluated in single-chamber microbial fuel cells (MFCs) with acetate and glucose as carbon sources. Power output was not affected by selenite up to 125 mg l⁻¹ with glucose as substrate. Coulombic efficiencies of MFCs with glucose increased from 25% to 38% at 150 mg Se l⁻¹. About 99% of 50 and 200 mg Se l⁻¹ selenite was removed in 48 and 72 h for MFCs fed with acetate and glucose, respectively, demonstrating the potential of using MFC technology for Se remediation.     

Electricity generation in single-chamber microbial fuel cells using a carbon source sampled from anaerobic reactors utilizing grass silage

Production of electricity from samples obtained during anaerobic digestion of grass silage was examined using single-chamber air-cathode mediator-less microbial fuel cells (MFCs). The samples were obtained from anaerobic reactors at start-up conditions after 3 and 10 days of operation under psychrophilic (15 °C) and mesophilic (37 °C) temperatures. Electricity was directly produced from all samples at a concentration of 1500 mg COD L⁻¹. Power density obtained from the samples, as a sole carbon source, ranged from 56 ± 3 W m⁻³ to 31 ± 1 W m⁻³ for the mesophilic and psychrophilic samples, respectively. Coulombic efficiencies ranged from 18 ± 1% to 12 ± 1% for the same samples. The relationship between the maximum voltage output and initial COD concentration appeared to follow saturation kinetics at the external resistance of 217 Ω. Chemical oxygen demand (COD) removal was over 90% and total phenolics removal was in the range of 30-75% for all samples tested, with a standard amount of 60 mg L⁻¹ total phenolics removed for every sample. Our results indicate that generating electricity from solution samples of anaerobic reactors utilizing grass silage is possible, opening the possibility for combination of anaerobic digestion with MFC technology for energy generation.     

Electricity generation and microbial community changes in microbial fuel cells packed with different anodic materials

Four materials, carbon felt cube (CFC), granular graphite (GG), granular activated carbon (GAC) and granular semicoke (GS) were tested as packed anodic materials to seek a potentially practical material for microbial fuel cells (MFCs). The microbial community and its correlation with the electricity generation performance of MFCs were explored. The maximum power density was found in GAC, followed by CFC, GG and GS. In GAC and CFC packed MFCs, Geobacter was the dominating genus, while Azospira was the most populous group in GG. Results further indicated that GAC was the most favorable for Geobacter adherence and growth, and the maximum power densities had positive correlation with the total biomass and the relative abundance of Geobacter, but without apparent correlation with the microbial diversity. Due to the low content of Geobacter in GS, power generated in this system may be attributed to other microorganisms such as Synergistes, Bacteroidetes and Castellaniella.     

Responses from freshwater sediment during electricity generation using microbial fuel cells

In a two-electrode system, freshwater sediment was used as a fuel to examine the relationship between current generation and organic matter consumption with different types of electrode. Sediment microbial fuel cells using porous electrodes showed a superior performance in terms of generating current when compared with the use of non-porous electrodes. The maximum current densities with thicker and thin porous electrodes were 45.4 and 37.6 mA m⁻², respectively, whereas the value with non-porous electrodes was 13.9 mA m⁻². The amount of organic matter removed correlated with the current produced. The redox potential in the anode area under closed-circuit conditions was +246.3 ± 67.7 mV, while that under open-circuit conditions only reached −143.0 ± 7.18 mV. This suggests that an application of this system in organic-rich sediment could provide environmental benefits such as decreasing organic matter and prohibiting methane emission in conjunction with electricity production via an anaerobic oxidation process.     

Anode microbial communities produced by changing from microbial fuel cell to microbial electrolysis cell operation using two different wastewaters

Conditions in microbial fuel cells (MFCs) differ from those in microbial electrolysis cells (MECs) due to the intrusion of oxygen through the cathode and the release of H₂ gas into solution. Based on 16S rRNA gene clone libraries, anode communities in reactors fed acetic acid decreased in species richness and diversity, and increased in numbers of Geobacter sulfurreducens, when reactors were shifted from MFCs to MECs. With a complex source of organic matter (potato wastewater), the proportion of Geobacteraceae remained constant when MFCs were converted into MECs, but the percentage of clones belonging to G. sulfurreducens decreased and the percentage of G. metallireducens clones increased. A dairy manure wastewater-fed MFC produced little power, and had more diverse microbial communities, but did not generate current in an MEC. These results show changes in Geobacter species in response to the MEC environment and that higher species diversity is not correlated with current.     

Factors affecting current production in microbial fuel cells using different industrial wastewaters

This study evaluated how different types of industrial wastewaters (bakery, brewery, paper and dairy) affect the performance of identical microbial fuel cells (MFCs); and the microbial composition and electrochemistry of MFC anodes. MFCs fed with paper wastewater produced the highest current density (125 ± 2 mA/m²) at least five times higher than dairy (25 ± 1 mA/m²), brewery and bakery wastewaters (10 ± 1 mA/m²). Such high current production was independent of substrate degradability. A comprehensive study was conducted to determine the factor driving current production when using the paper effluent. The microbial composition of anodic biofilms differed according to the type of wastewater used, and only MFC anodes fed with paper wastewater showed redox activity at −134 ± 5 mV vs NHE. Electrochemical analysis of this redox activity indicated that anodic bacteria produced a putative electron shuttling compound that increased the electron transfer rate through diffusion, and as a result the overall MFC performance.     

Iron phthalocyanine supported on amino-functionalized multi-walled carbon nanotube as an alternative cathodic oxygen catalyst in microbial fuel cells

Amino-functionalized multi-walled carbon nanotube (a-MWCNT)-supported iron phthalocyanine (FePc) (a-MWCNT/FePc) has been investigated as a catalyst for the oxygen reduction reaction (ORR) in an air-cathode single-chambered microbial fuel cell (MFC). Cyclic and linear sweep voltammogram are employed to investigate the electrocatalytic activity of the a-MWCNT/FePc for ORR. The maximum power density of 601 mW m⁻² is achieved from a MFC with the a-MWCNT/FePc cathode, which is the highest energy output compared to those MFCs with other materials supported FePc, such as carbon black, pristine MWCNT (p-MWCNT), carboxylic acid functionalized MWCNT (c-MWCNT), and even with a Pt/C cathode. Furthermore, cyclic voltammetry performed on the a-MWCNT/FePc electrode suggests that the a-MWCNT/FePc has an electrochemical activity for ORR via a four-electron pathway in a neutral pH solution. This work provides a potential alternative to Pt in MFCs for sustainable energy generation.     

Composition and distribution of internal resistance in three types of microbial fuel cells

High internal resistance is a key problem limiting the power output of the microbial fuel cell (MFC). Therefore, more knowledge about the internal resistance is essential to enhance the performance of the MFC. However, different methods are used to determine the internal resistance, which makes the comparison difficult. In this study, three different types of MFCs were constructed to study the composition and distribution of internal resistance. The internal resistance (R _i) is partitioned into anodic resistance (R _a), cathodic resistance (R _c), and ohmic resistance () according to their origin and the design of the MFCs. These three resistances were then evaluated by the “current interrupt” method and the “steady discharging” method based on the proposed equivalent circuits for MFCs. In MFC-A, MFC-B, and MFC-C, the R _i values were 3.17, 0.35, and 0.076 Ω m², the values were 2.65, 0.085, and 0.008 Ω m², the R _a values were 0.055, 0.115, and 0.034 Ω m², and the R _c values were 0.466, 0.15, and 0.033 Ω m², respectively. For MFC-B and MFC-C, the remarkable decrease in R _i compared with the two-chamber MFC was mainly ascribed to the decline in and R _c. In MFC-C, the membrane electrodes’ assembly lowered the ohmic resistance and facilitated the mass transport through the anode and cathode electrodes, resulting in the lowest R _i among the three types.     

Effects of sediment pretreatment on the performance of sediment microbial fuel cells

In the present study, the effects of different pretreatment methods for sediments on the performance of sediment microbial fuel cells (SMFCs) were evaluated. Autoclaved (30 and 60 min), and heated (150 °C, 3 h) sediments demonstrated high power density, compared with control and heated (60 °C, 3 h) sediments. An SMFC with heated (60 °C, 3 h) sediment was found to easily form a biocathode. The power density of an SMFC with heated (150 °C, 3 h) sediment was 214 mW m(-2) on day 24. Furthermore, autoclaved (30 and 60 min) and heated (3 h, 60 and 150 °C) sediments accelerated the production of dissolved organic matter (DOM). The DOM in heated (60 °C, 3 h) sediments had larger molecular sizes. The present study demonstrates that SMFCs can have high power density and high loss on ignition removal efficiencies when produced from sediments by suitable pretreatment methods.