DNA microarrays on nanoscale-controlled surface

We have developed new surface to ensure a proper spacing between immobilized biomolecules. While DNA microarray on this surface provided each probe DNA with ample space for hybridization with incoming target DNAs, the microarray showed enhanced discrimination efficiency for various types of single nucleotide polymorphism. The high discrimination efficiency holds for all tested cases (100:<1 for internal mismatched cases; 100:<28 for terminal mismatched ones). In addition, by investigating influence of hybridization temperature and washing condition on the fluorescence intensity and the discrimination efficiency with and without controlled mesospacing, it was observed that the nanoscale-controlled surface showed good discrimination efficiency in a wide range of temperature (37–50°C), and hybridization behavior on the surface was in agreement with the solution one. Intriguingly, it was found that washing process after the hybridization was critical for the high discrimination efficiency. For the particular case, washing process was so efficient that only 30 s washing was sufficient to reach the optimal discrimination ratio.     

Shielding effect of monovalent and divalent cations on solid-phase DNA hybridization: surface plasmon resonance biosensor study

Solid-phase hybridization, i.e. the process of recognition between DNA probes immobilized on a solid surface and complementary targets in a solution is a central process in DNA microarray and biosensor technologies. In this work, we investigate the simultaneous effect of monovalent and divalent cations on the hybridization of fully complementary or partly mismatched DNA targets to DNA probes immobilized on the surface of a surface plasmon resonance sensor. Our results demonstrate that the hybridization process is substantially influenced by the cation shielding effect and that this effect differs substantially for solid-phase hybridization, due to the high surface density of negatively charged probes, and hybridization in a solution. In our study divalent magnesium is found to be much more efficient in duplex stabilization than monovalent sodium (15 mM Mg²⁺ in buffer led to significantly higher hybridization than even 1 M Na⁺). This trend is opposite to that established for oligonucleotides in a solution. It is also shown that solid-phase duplex destabilization substantially increases with the length of the involved oligonucleotides. Moreover, it is demonstrated that the use of a buffer with the appropriate cation composition can improve the discrimination of complementary and point mismatched DNA targets.     

Hybridization biosensor using 2-nitroacridone as electrochemical indicator for detection of short DNA species of Chronic Myelogenous Leukemia

A new acridone derivative 2-nitroacridone (NAD) was synthesized in this paper, and it was found that NAD had excellent electrochemical activity on the glassy carbon electrode (GCE) with a couple reversible redox peaks at 0.051 V and 0.103 V, respectively. Voltammetry was used to investigate the electrochemical behavior of NAD and the interaction between NAD and salmon sperm DNA. In pH 4.0 phosphate buffer solution, the binding ratio between NAD and salmon sperm DNA was calculated to be 2:1 and the binding constant was 3.19 × 10⁵ L/mol. A Chronic Myelogenous Leukemia (CML, Type b₃a₂) DNA biosensor was developed by immobilizing covalently single-stranded CML DNA fragments to a modified GCE. The surface hybridization of the immobilized single-stranded CML DNA fragment with its complementary DNA fragment was evidenced by electrochemical methods using NAD as a novel electrochemical indicator, with a detection limit of 6.7 × 10⁻⁹ M and a linear response range of 1.8 × 10⁻⁸ M to 9.1 × 10⁻⁸ M for CML DNA. Selective determination of complementary ssDNA was achieved using differential pulse voltammetry (DPV).     

Real-time detection of Escherichia coli O157:H7 sequences using a circulating-flow system of quartz crystal microbalance

A DNA piezoelectric biosensing method for real-time detection of Escherichia coli O157:H7 in a circulating-flow system was developed in this study. Specific probes [a 30-mer oligonucleotide with or without additional 12 deoxythymidine 5′-monophosphate (12-dT)] for the detection of E. coli O157:H7 gene eaeA, synthetic oligonucleotide targets (30 and 104 mer) and PCR-amplified DNA fragments from the E. coli O157:H7 eaeA gene (104 bp), were used to evaluate the efficiency of the probe immobilization and hybridization with target DNA in the circulating-flow quartz crystal microbalance (QCM) device. It was found that thiol modification on the 5′-end of the probes was essential for probe immobilization on the gold surface of the QCM device. The addition of 12-dT to the probes as a spacer, significantly enhanced (P < 0.05) the hybridization efficiency (H%). The results indicate that the spacer enhanced the H% by 1.4- and 2-fold when the probes were hybridized with 30- and 104-mer targets, respectively. The spacer reduced steric interference of the support on the hybridization behavior of immobilized oligonucleotides, especially when the probes hybridized with relatively long oligonucleotide targets. The QCM system was also applied in the detection of PCR-amplified DNA from real samples of E. coli O157:H7. The resultant H% of the PCR-amplified double-strand DNA was comparable to that of the synthetic target T-104AS, a single-strand DNA. The piezoelectric biosensing system has potential for further applications. This approach lays the groundwork for incorporating the method into an integrated system for rapid PCR-based DNA analysis.     

Detection of guanine-adenine mismatches by surface plasmon resonance sensor carrying naphthyridine-azaquinolone hybrid on the surface

We have discovered a new molecule naphthyridine–azaquinolone hybrid (Npt–Azq) that strongly stabilized the guanine-adenine (G-A) mismatch in duplex DNA. In the presence of Npt–Azq, the melting temperature (T_m) of 5′-d(CTA ACG GAA TG)-3′/3′-d(GAT TGA CTT AC)-5′ containing a single G-A mismatch increased by 15.4°C, whereas fully matched duplex increased its T_m only by 2.2°C. Npt–Azq was immobilized on the sensor surface for the surface plasmon resonance (SPR) assay to examine SPR detection of duplexes containing a G-A mismatch. Distinct SPR signals were observed when 27mer DNA containing a G-A mismatch was analyzed by the Npt–Azq immobilized sensor surfaces, whereas the signal of the fully matched duplex was ~6-fold weaker in intensity. The SPR signals for the G-A mismatch were proportional to the concentration of DNA in a range up to 1 µM, confirming that the SPR signal is in fact due to the binding of the G-A mismatch to Npt–Azq immobilized on the surface. Examination of all 16 G-A mismatches regarding the flanking sequence revealed that the sensor surface reported here is applicable to eight flanking sequences, covering 50% of all possible G-A mismatches.     

Sequencing by hybridization with the generic 6-mer oligonucleotide microarray: an advanced scheme for data processing

DNA sequencing by hybridization was carried out with a microarray of all 4(6) = 4,096 hexadeoxyribonucleotides (the generic microchip). The oligonucleotides immobilized in 100 x 100 x 20-microm polyacrylamide gel pads of the generic microchip were hybridized with fluorescently labeled ssDNA, providing perfect and mismatched duplexes. Melting curves were measured in parallel for all microchip duplexes with a fluorescence microscope equipped with CCD camera. This allowed us to discriminate the perfect duplexes formed by the oligonucleotides, which are complementary to the target DNA. The DNA sequence was reconstructed by overlapping the complementary oligonucleotide probes. We developed a data processing scheme to heighten the discrimination of perfect duplexes from mismatched ones. The procedure was united with a reconstruction of the DNA sequence. The scheme includes the proper definition of a discriminant signal, preprocessing, and the variational principle for the sequence indicator function. The effectiveness of the procedure was confirmed by sequencing, proofreading, and nucleotide polymorphism (mutation) analysis of 13 DNA fragments from 31 to 70 nucleotides long.     

Discrimination between perfect and mismatched duplexes with oligonucleotide gel microchips: role of thermodynamic and kinetic effects during hybridization

The efficiency of discrimination between perfect and mismatched duplexes during hybridization on microchips depends on the concentrations of target DNA in solution and immobilized probes, buffer composition, and temperature of hybridization and is determined by both thermodynamic relationships and hybridization kinetics. In this work, optimal conditions of discrimination were studied using hybridization of fluorescently labeled target DNA with custom-made gel-based oligonucleotide microchips. The higher the concentration of immobilized probes and the higher the association constant, the higher the concentration of the formed duplexes and the stronger the corresponding fluorescence signal, but, simultaneously, the longer the time needed to reach equilibrium. Since mismatched duplexes hybridize faster than their perfect counterparts, perfect-to-mismatch signal ratio is lower in transient regime, and short hybridization times may hamper the detection of mutations. The saturation time can be shortened by decreasing the probe concentration or augmenting the gel porosity. This improves the detection of mutations in transient regime. It is shown that the decrease in the initial concentration of oligonucleotide probes by an order of magnitude causes only 1.5-2.5-fold decrease of fluorescence signals after hybridization of perfect duplexes for 3-12 h. At the same time, these conditions improve the discrimination between perfect and mismatched duplexes more than two-fold. A similar improvement may be obtained using an optimized dissociation procedure.     

DNA biosensor based on hybridization refractory mutation system approach for single mismatch detection

We report on a simple approach to enhance solid-phase hybridization-based single base mismatch discrimination at high ionic strength based on the deliberate insertion of a natural DNA base mismatch in the surface-tethered probe. A large drop in hybridization signal of single base mismatched alleles using the designed probe as compared with the conventional probe, from 80% to less than 25% of the signal obtained with the fully complementary, non-mutation-containing sequence, when using colorimetric detection was further improved to 20% when using electrochemical detection, attributable to a difference of spacing of immobilized probes. Finally, the designed probe was used for the electrochemical detection of the DQA1*05:05 allele amplified from real human blood samples.     

Electrochemical DNA biosensor based on silver nanoparticles/poly(3-(3-pyridyl) acrylic acid)/carbon nanotubes modified electrode

In this work, we present an electrochemical DNA sensor based on silver nanoparticles/poly(trans-3-(3-pyridyl) acrylic acid) (PPAA)/multiwalled carbon nanotubes with carboxyl groups (MWCNTs-COOH) modified glassy carbon electrode (GCE). The polymer film was electropolymerized onto MWCNTs-COOH modified electrode by cyclic voltammetry (CV), and then silver nanoparticles were electrodeposited on the surface of PPAA/MWCNTs-COOH composite film. Thiol group end single-stranded DNA (HS-ssDNA) probe was easily covalently linked onto the surface of silver nanoparticles through a 5′ thiol linker. The DNA hybridization events were monitored based on the signal of the intercalated adriamycin by differential pulse voltammetry (DPV). Based on the response of adriamycin, only the complementary oligonucleotides gave an obvious current signal compared with the three-base mismatched and noncomplementary oligonucleotides. Under the optimal conditions, the increase of reduction peak current of adriamycin was linear with the logarithm of the concentration of the complementary oligonucleotides from 9.0 × 10⁻¹² to 9.0 × 10⁻⁹ M with a detection limit of 3.2 × 10⁻¹² M. In addition, this DNA sensor exhibited an excellent reproducibility and stability during DNA hybridization assay.     

An ultrasensitive supersandwich electrochemical DNA biosensor based on gold nanoparticles decorated reduced graphene oxide

In this article, a supersandwich-type electrochemical biosensor for sequence-specific DNA detection is described. In design, single-strand DNA labeled with methylene blue (MB) was used as signal probe, and auxiliary probe was designed to hybridize with two different regions of signal probe. The biosensor construction contained three steps: (i) capture DNA labeled with thiol was immobilized on the surface of gold nanoparticles decorated reduced graphene oxide (Au NPs/rGO); (ii) the sandwich structure formation contained “capture–target–signal probe”; and (iii) auxiliary probe was introduced to produce long concatamers containing signal molecule MB. Differential pulse voltammetry (DPV) was used to monitor the DNA hybridization event using peak current changes of MB in phosphate-buffered saline (PBS) containing 1.0 M NaClO₄. Under optimal conditions, the peak currents of MB were linear with the logarithm of the concentration of target DNA in the range of 0.1 μM to 0.1 fM with a detection limit of 35 aM (signal/noise = 3). In addition, this biosensor exhibited good selectivity even for single-base mismatched target DNA detection.     

Point mutation detection with the sandwich method employing hydrogel nanospheres by the surface plasmon resonance imaging technique

We propose a surface modification procedure to construct DNA arrays for use in surface plasmon resonance (SPR) imaging studies for the highly sensitive detection of a K-ras point mutation, enhanced with hydrogel nanospheres. A homobifunctional alkane dithiol was adsorbed on Au film to obtain the thiol surface, and ethyleneglycol diglycidylether (EGDE) was reacted to insert the ethyleneglycol moiety, which can suppress nonspecific adsorption during SPR analysis. Then streptavidin (SA) was immobilized on EGDE using tosyl chloride activation. Biotinylated DNA ligands were bound to the SA surface via biotin-SA interaction to fabricate DNA arrays. In SPR analysis, the DNA analyte was exposed on the DNA array and hybridized with the immobilized DNA probes. Subsequently, the hydrogel nanospheres conjugated with DNA probes were bound to the DNA analytes in a sandwich configuration. The DNA-carrying nanospheres led to SPR signal enhancement and enabled us to discriminate a K-ras point mutation in the SPR difference image. The application of DNA-carrying hydrogel nanospheres for SPR imaging assays was a promising technique for high throughput and precise detection of point mutations.     

Analysis of Perfect and Mismatched DNA Duplexes with a Generic Hexanucleotide Microchip

Thermodynamic analysis was performed for the duplexes formed by fluorescently labeled oligonucleotide targets on a generic hexanucleotide microchip. All 4096 different hexanucleotide chains were immobilized as probes in individual gel pads of the microchip. To strengthen the hybridization, each hexamer was extended at both ends by one nucleotide from the equimolar mixture of all four nucleotides to serve as nonselective linkers. It has been shown that the melting curves for oligonucleotide duplexes formed on the microchip and in a solution are quite similar. The influence of ionic surrounding has been studied in terms of the hybridization efficiency and discrimination between the mismatched and perfect duplexes. Different approaches have been tested to compensate the dependence of duplex stability on the GC content. It has been demonstrated that the use of chaotropic agents, addition of nonlabeled GC-rich competitor oligonucleotides, as well as creation of a temperature gradient along the microchip reproducing the distribution of melting temperatures, efficiently level out the AT/GC differences. The use of tetramethylammonium chloride for the same purpose was accompanied by weakening to some extent the discrimination between the mismatched duplexes and the perfect ones.     

Liquid phase SPR imaging experiments for biosensors applications

Surface plasmon resonance (SPR) has recently gained attention as a label-free method for the detection of biological molecules binding onto functionalised surfaces. It is one of the most sensitive detection method for monitor variations in the thickness and refractive index in ultra-thin films. Here, the adsorption processes of oligonucleotides onto gold substrates have been investigated in aqueous buffer solution using SPR imaging measurements. The hybridization of a thiol-modified, single stranded oligonucleotide anchored to a gold surface via thiol group, with its complementary sequence has been observed and characterised monitoring the hybridization process by SPR equipment. In situ investigation of smallest changes in SPR imaging measurements dynamically performed in liquid phase in the presence of DNA complementary probes was performed. Infrared spectroscopy and scanning electron microscopy characterisation of the functionalised gold surfaces of the biosensor were compared with the images obtained by SPR experimental apparatus.     

G‐rich sequence‐functionalized polystyrene microsphere‐based instantaneous derivatization for the chemiluminescent amplified detection of DNA

Herein, we develop a novel chemiluminescence (CL) approach with high sensitivity and excellent selectivity, by taking advantage of magnetic beads as preconcentration carriers and polystyrene microspheres as an amplification platform. Briefly, a ‘sandwich‐type’ detection strategy is employed in our design, which involves capture probe DNA immobilized on the surface of carboxyl‐terminated magnetic beads and multiple biotinylated reporter DNA self‐assembled on the surface of streptavidin‐modified polystyrene microspheres. The reporter DNA includes a guanine nucleobase‐rich (G‐rich) sequence domain for the generation of light and an additional tethered nucleic acid domain complementary with the target DNA. The CL signal is obtained via a novel instantaneous derivatization reaction between a specific CL reagent and the guanine nucleo­bases rich in the target and reporter DNA. As a result, we demonstrate that this DNA assay is reproducible, stable, easy to use, and can sensitively detect femtomolar target DNA related to anthrax lethal factors with excellent differentiation ability for single‐base mismatched sequences. Overall, this new CL protocol couples the high sensitivity of CL analysis with effective magnetic separation for discriminating against unwanted constituents such as mismatched sequences, and hence, offers great promise for DNA hybridization analysis. Copyright © 2009 John Wiley & Sons, Ltd.     

Single base mismatch detection by microsecond voltage pulses

A single square voltage pulse applied to metal electrodes underneath a silicon dioxide film upon which DNA probes are immobilized allows the discrimination of DNA targets with a single base mismatch during hybridization. Pulse duration, magnitude and slew rate of the voltage pulse are all key factors controlling the rates of electric field assisted hybridization. Although pulses with 1 V, lasting less than 1 ms and with a rise/fall times of 4.5 ns led to maximum hybridization of fully complementary strands, lack of stringency did not allow the discrimination of single base mismatches. However, by choosing pulse conditions that are slightly off the optimum, the selectivity for discriminating single base mismatches could be improved up to a factor approximately 5 when the mismatch was in the middle of the strand and up to approximately 1.5 when the mismatch was on the 5'-end and. These results demonstrate that hybridization with the appropriate electric field pulse provides a new, site-specific, approach to the discrimination of single nucleotide polymorphisms in the sub-millisecond time scale, for addressable DNA microarrays.     

Stabilization of the immobilized linkers and DNA probes for DNA microarray fabrication by end-capping of the remaining unreacted silanol on the glass

High stability of the oligonucleotides immobilized on the glass is essential for the reliable DNA microarray analysis. In the present study, effect of end-capping of the unreacted silanol, remaining after the surface amine-functionalization, was explored: (1) Cy3-NHS (N-hydorxysuccinincimide) dye was spotted on the surface and change in the fluorescent intensity was measured. (2) DNA probes were immobilized by the reactivity of oxanine linked at the 5’-end, the complementary oligonucleotides with Cy5-fluorescence at the 5’-end was hybridized, and the time-dependence of the fluorescence intensity was observed. Both the systems showed improved stability of the immobilized molecules, indicative of the stabilization by end-capping.     

Detection of Single-Base Substitutions in Amplified Fragments via Ligation of a Tandem of Short Oligonucleotides in Solution and on a Solid Carrier

Ligation of a tandem of short oligonucleotides was proposed for detecting single-base substitutions in amplified DNA fragments. An octamer–tetramer–octamer tandem was ligated on a 20-mer template with T4 DNA ligase. As shown with radiolabeled oligonucleotides, the efficiency and selectivity of ligation did not change with an octamer linked to a water-soluble carrier based on polyethylene glycol (MPEG), while ligation was somewhat lower with the octamer immobilized on methacrylate beads (DMEG). In both cases, polymer attachment improved the discrimination of 20-mer templates with single-base substitutions in the binding site for the tetramer or for the immobilized octamer. Tandems with a radiolabeled or biotinylated component were also efficiently ligated on amplified DNA fragments. The data obtained with DNA fragments of HIV-1 strains bru and rf demonstrate the possibility of reliable detection of single-base substitutions via ligation of a tandem and colorimetric detection of the immobilized ligation product with the streptavidin–alkaline phosphatase technique.     

[Cu(phen)2] acts as electrochemical indicator and anchor to immobilize probe DNA in electrochemical DNA biosensor

We demonstrate a novel protocol for sensitive in situ label-free electrochemical detection of DNA hybridization based on copper complex ([Cu(phen)₂]²⁺, where phen = 1,10-phenanthroline) and graphene (GR) modified glassy carbon electrode. Here, [Cu(phen)₂]²⁺ acted advantageously as both the electrochemical indicator and the anchor for probe DNA immobilization via intercalative interactions between the partial double helix structure of probe DNA and the vertical aromatic groups of phen. GR provided large density of docking site for probe DNA immobilization and increased the electrical conductivity ability of the electrode. The modification procedure was monitored by electrochemical impedance spectroscopy (EIS). Square-wave voltammetry (SWV) was used to explore the hybridization events. Under the optimal conditions, the designed electrochemical DNA biosensor could effectively distinguish different mismatch degrees of complementary DNA from one-base mismatch to noncomplementary, indicating that the biosensor had high selectivity. It also exhibited a reasonable linear relationship. The oxidation peak currents of [Cu(phen)₂]²⁺ were linear with the logarithm of the concentrations of complementary target DNA ranging from 1 × 10⁻¹² to 1 × 10⁻⁶ M with a detection limit of 1.99 × 10⁻¹³ M (signal/noise = 3). Moreover, the stability of the electrochemical DNA biosensor was also studied.     

Comparison of surface plasmon resonance and capacitive immunosensors for cancer antigen 125 detection in human serum samples

This paper presents a comparison between surface plasmon resonance (SPR) and capacitive immunosensors for a flow injection label-free detection of cancer antigen 125 (CA 125) in human serum. Anti-CA 125 was immobilized on gold surface through a self-assembled monolayer. Parameters affecting the responses of each system were optimized. Under optimal conditions, SPR provided a detection limit of 0.1 U ml⁻¹ while 0.05 U ml⁻¹ was obtained for the capacitive system. Linearity for SPR was between 0.1 and 40 U ml⁻¹ and 0.05–40 U ml⁻¹ for capacitive system. These immunosensors were applied to analyze CA 125 concentrations in human serum samples and compared with conventional enzyme linked fluorescent assay (ELFA). Both systems showed good agreement with ELFA (P < 0.05). Moreover, these immunosensors were very stable and provided good reproducible responses after regeneration, up to 32 times for SPR and 48 times for capacitive system with relative standard deviation lower than 4%. The SPR immunosensor provided advantages in term of fast response and real-time monitoring while capacitive immunosensor offered a sensitive and cost-effective method for CA 125 detection.     

Highly sensitive measurements of PNA-DNA hybridization using oxide-etched silicon nanowire biosensors

The highly sensitive and sequence-specific detection of single-stranded oligonucleotides using nonoxidized silicon nanowires (SiNWs) is demonstrated. To maximize device sensitivity, the surface of the SiNWs was functionalized with a densely packed organic monolayer via hydrosilylation, subsequently immobilized with peptide nucleic acid (PNA) capable of recognizing the label-free complementary target DNA. Because of the selective functionalization of the SiNWs, binding competition between the nanowire and the underlying oxide is avoided. Transmission electron microscopy was conducted to clearly differentiate the SiNW surface before and after removal of SiO₂. Fluorescence microscopy was used to further realize the selectivity of the oxide-etched chemistry on the SiNWs and sequence specificity of PNA-DNA hybridization. The concentration-dependent resistance change measurements upon hybridization of PNA-DNA show that detection limit down to 10 fM can be obtained. The SiNW devices also reveal the capability of an obvious discrimination against mismatched sequences. Among several efforts being made to improve detection sensitivity, this work addresses one significant issue regarding surface functionalization which enables highly sensitive biomolecular sensing with SiNWs.