Determination of excitatory amino acids in biological fluids by capillary electrophoresis with optical fiber light-emitting diode induced fluorescence detection

The capillary electrophoresis (CE) system with optical fiber light-emitting diode (optical fiber LED) induced fluorescence detector was developed for the analysis of the excitatory amino acids (EAAs) tagged with naphthalene-2,3-dicarboxaldehyde (NDA). The separation of EAAs was carried out in an uncoated fused-silica capillary (50 cm x 75 microm i.d.) with a buffer of 10 mM borate at pH 9.3 and an applied voltage of 20 kV. High sensitivity was obtained by the use of optical fiber LED induced fluorescence detector with a violet LED as the excitation light source. The limits of detection (S/N = 3) for glutamic acid (Glu) and aspartic acid (Asp) were 2.1 x 10(-8) and 2.3 x 10(-8) M, respectively. The detection approach was successfully applied to the analysis of Glu and Asp in biological fluids including human serum, rabbit serum and human cerebrospinal fluid (CSF) with satisfactory results.     

Determination of lactate dehydrogenase in human erythrocytes by capillary electrophoresis with electrochemical detection

Capillary electrophoresis (CE) was employed to analyze lactate dehydrogenase (LDH) in human erythrocytes using an amperometric detector with a carbon fiber micro-disk bundle electrode. LDH activity was measured by determining the amount of NADH generated by LDH through a enzyme-catalyzed reaction between NAD(+) and lithium lactate. The factors influencing the enzyme-catalyzed reaction, separation and detection were examined and optimized. The following conditions were suitable for the determination of LDH: running buffer, 5.0 x 10(-2)mol/l Tris-HCl (pH 7.5); separation voltage, 20.0 kV; detection potential, 1.00 V (versus saturated calomel electrode (SCE)). The conditions of enzyme-catalyzed reaction were: reaction buffer, 5.0 x 10(-2)mol/l Tris-HCl (pH 9.3); substrates, 5.0 x 10(-2)mol/l lithium lactate and 5.0 x 10(-3)mol/l NAD(+); reaction time, 10 min. The concentration limit of detection (LOD) of the method was 0.017 U/ml at a signal-to-noise (S/N) ratio of 3, which corresponded to 1.10 x 10(-10)mol/l, and the mass LOD was 2 x 10(-20)mol. The linear dynamic range was 0.039-4.65 U/ml for the injection voltage of 5.0 kV and injection time of 10s. The relative standard deviation (R.S.D.) was 0.85% for the migration time and 1.8% for the electrophoretic peak area. The method was applied to determine LDH in human erythrocytes. The recovery of the method was between 98 and 101%.     

Determination of ascorbic acid in individual rat hepatocyte by capillary electrophoresis with electrochemical detection

A method for the direct determination of ascorbic acid (AA) in individual rat hepatocyte based on capillary electrophoresis (CE) coupled with electrochemical detection (ECD) using a new kind of homemade carbon fiber micro-disk bundle electrode has been described. Individual rat hepatocytes were injected into a fused-silica capillary with an inner diameter of 25 microm, and lysed by 0.1% sodium dodecylsulfate (SDS) as cell lysis solution. The following conditions were suitable for the determination of AA: running buffer, 1.83 x 10(-2) mol/l Na2HPO4-1.70 x 10(-3) mol/l NaH2PO4 (pH 7.8); separation voltage, 20.0 kV; detection potential, 0.80 V (vs. saturated calomel electrode (SCE)). The concentration limit of detection (LOD) of the method was 1.7 x 10(-6) mol/l at a signal-to-noise (S/N) ratio of 3, and the mass LOD was 3.0 fmol. The linear dynamic range was from 5.0 x 10(-6) to 5.0 x 10(-4) mol/l with a correlation coefficient of 0.9962 for the injection voltage of 5.0 kV and injection time of 10s. The relative standard deviation (R.S.D.) was 0.85% for the migration time and 1.8% for the peak current. This method was successfully applied to AA determination in rat hepatocyte. The recovery was between 91% and 97%, and the amount of AA in single rat hepatocyte ranged from 28 to 63 fmol.     

Capillary electrophoresis of phosphorylated amino acids with fluorescence detection

A rapid and sensitive capillary electrophoresis (CE) method coupled with fluorescence detection was developed for identification of protein phosphorylation by determination of phosphoamino acids. Naphthalene-2,3-dicarboxaldehyde (NDA), a fluorescence derivatization reagent, was used to label protein hydrolysate. The optimal derivatization reaction was performed with 3.5mM NDA, 40 mM NaCN and 20mM borate buffer (pH 10.0) for 15 min. The baseline separation of three phosphorylated amino acids could be obtained in less than 180 s with good repeatability by using 30 mM borate (pH 9.2) containing 2.0mM beta-cyclodextrin (beta-CD) as the running buffer. The detection limits for phosphothreonine, phosphotyrosine and phosphoserine were 7.0 x 10(-9)M, 5.6 x 10(-9)M and 7.2 x 10(-9)M, respectively (S/N=3). Also, the interference from other protein amino acids with large molar excess over that of phosphoamino acids was studied. With beta-casein as the analysis protein, this method was successfully validated.     

Determination of agmatine in biological samples by capillary electrophoresis with chemiluminescence detection

A fast and simple method based on capillary electrophoresis (CE) with chemiluminescence (CL) detection has been developed for the determination of agmatine, a recently identified neurotransmitter/modulator. The CE run time was approximately 2 min for each sample injected. CL detection employed a lab-built reaction flow cell and a photon counter. The CL reagents used were luminol and NaBrO. The optimized conditions for the CL detection were 5 x 10(-4)M luminol added to the CE running buffer and 5.0 x 10(-4)M NaBrO in 100 mM NaCO3-NaOH buffer solution at pH 12.5 introduced post column. Detection limit for agmatine was 4.3 x 10(-6)M (S/N=3). The precision (R.S.D.) on peak height (at 1 x 10(-5)M agmatine) and migration time were 3.7 and 2.5%, respectively. The present CE-CL method was evaluated with the determination of agmatine in tissue samples taken from rat brain, and rat and monkey stomachs. Samples were directly injected into the CE-CL system after the removal of proteins. A higher level of agmatine was detected in the stomach samples. Agmatine concentrations in the tissue samples taken from rat and monkey stomachs were similar at approximately 1950 ng/g wet tissue.     

Simple luminescence detectors using a light-emitting diode or a Xe lamp, optical fiber and charge-coupled device, or photomultiplier for determining proteins in capillary electrophoresis: a critical comparison

The performance of two homemade fluorescence-induced capillary electrophoresis detectors, one based on light-emitting diode (LED) as the excitation source and a charge-coupled device (CCD) photodetector and the other based on a commercial luminescence spectrometer (Xe lamp) as the excitation source and a photomultiplier tube as a detector, were compared for the determination of fluorescent proteins R-phycoerythrin and B-phycoerythrin. Both devices use commercially available, reasonably priced optical components that can be used by nonexperts. After fine optimization of several optical and separation parameters in both devices, a zone capillary electrophoresis methodology was achieved with 50mM borate buffer (pH 8.4) and 10mM phytic acid for the determination of two phycobiliproteins. Detection limits of 0.50 and 0.64microg/ml for R-phycoerythrin and B-phycoerythrin, respectively, were achieved by using the LED-induced fluorescence capillary electrophoresis (LED-IF-CE) system, and corresponding detection limits of 2.73 and 2.16microg/ml were achieved by using the Xe lamp-IF-CE system. Analytical performance and other parameters, such as cost and potential to miniaturization, are compared for both devices.     

Determination of midecamycin by capillary zone electrophoresis with electrochemical detection

Capillary zone electrophoresis was employed for the determination of midecamycin using an end-column amperometric detection with a carbon fiber micro-disk bundle electrode at a constant potential of +1.15 V vs. saturated calomel electrode. The optimum conditions of separation and detection are 1.00x10(-3) mol l(-1) Na(2)HPO(4)-3.49x10(-4) mol l(-1) NaOH (pH 11.4) for the buffer solution, 20 kV for the separation voltage, 5 kV and 5 s for the injection voltage and the injection time, respectively. The limit of detection is 5.0x10(-7) mol l(-1) or 0.41 fmol (S/N=3). The linear range of the calibration curve is 1.00x10(-6)-1.00x10(-3) mol l(-1). The relative standard deviation is 1.4% for the migration time and 4.9% for the electrophoretic peak current. The method could be applied to the determination of midecamycin in human urine. In this case, a separation voltage of 14 kV was used.     

Methanol plug assisted sweeping-micellar electrokinetic chromatography for the determination of dopamine in urine by violet light emitting diode-induced fluorescence detection

The use and limitations of a methanol plug assisted sweeping-micellar electrokinetic chromatography (sweeping-MEKC) method is described. Using naphthalene-2,3-dicarboxaldehyde (NDA)-labeled dopamine as a model compound, this new method was also used in the determination of dopamine in actual urine samples. An inexpensive violet light emitting diode (LED) was used for the light source, because this is suitable for fluorescence excitation. The number of theoretical plates of the analyte was determined to be approximately 1 x 10(5) and approximately 2 x 10(5) by means of MEKC and sweeping-MEKC and this was improved to approximately 1 x 10(6) when the methanol plug assisted mode was applied. In addition, the detection limit of NDA-labeled dopamine was determined to be 9.1 x 10(-7) and 1.2 x 10(-8)M by means of MEKC and sweeping-MEKC and this was improved to 4.7 x 10(-9)M when the methanol plug assisted sweeping-MEKC mode was applied.     

Rapid,fluorimetric-liquid chromatographic determination of malondialdehyde in biological samples

Capillary zone electrophoresis was employed for the determination of lactate using end-column amperometric detection at a carbon fiber bundle microdisk electrode. The optimum conditions of separation and detection are 3.6 x 10(-3) mol/l Na(2)HPO(4)-1.4 x 10(-3) mol/l NaH(2)PO (pH 7.2) for the buffer solution, 18 kV for the separation voltage and 1.60 V versus the saturated calomel electrode for the detection potential. The limit of detection is 7.6 x 10(-7) mol/l or 1.7 fmol (S/N=3) and the linear range is 1.7 x 10(-6)-8.2 x 10(-4) mol/l for the injection voltage of 6 kV and injection time of 5 s. The RSD is 1.8% for the migration time and 3.3% for the electrophoretic peak current. The method was applied to the determination of lactate in human saliva. The recovery of the method is between 95 and 109%.     

Amperometric detection of perphenazine at a carbon fiber micro-disk bundle electrode by capillary zone electrophoresis

A simple method for determination of perphenazine by capillary zone electrophoresis with amperometric detection is described. The optimum conditions of separation and detection are 1.50 x 10(-3) mol/l Na(2)B(4)O(7)-1.0 x 10(-3) mol/l NaOH (pH 9.9) for the buffer solution, 18 kV for the separation voltage, 5 kV and 5 s for the injection voltage and the injection time, and 0.80 V versus saturated calomel electrode for the detection potential, respectively. The limit of detection is 5.0 x 10(-8) mol/l or 44 amol (S/N=3). The linear range of the calibration curve is 1.00 x 10(-7) to 1.00 x 10(-4) mol/l. The relative standard deviation is 1.5% for the migration time and 2.9% for the electrophoretic current at peak maximum. The method is applied to the determination of perphenazine in human urine.     

The sensitive determination of nucleic acids using a fluorescence-quenching method.

Experiments indicated that nucleic acids can quench the fluorescence of the Eu3+ -2-thenoyltrifluoroacetone (TTA)-1,10-phenanthroline (Phen) system. Based on this, a sensitive method for the determination of nucleic acids was proposed. The experiments indicated that under the optimum conditions, the quenched fluorescence intensity was in proportion to the concentration of nucleic acids in the range 1.0 x 10(-11)-1.0 x 10(-6) g/mL for yeast RNA (yRNA), 5.0 x 10(-11)-5.0 x 10(-7) g/mL for fish sperm (fsDNA) and 1.0 x 10(-10)-1.5 x 10(-6) g/mL for calf thymus DNA (ctDNA). Their detection limits were 3.0 x 10(-12), 4.0 x 10(-12) and 5.0 x 10(-11) g/mL, respectively. Therefore, the proposed method is one of the most sensitive methods available. The interaction between nucleic acids and Eu3+ -TTA-Phen is also discussed.     

Fluorescence enhancement effect of the morin-Al3+ -sodium dodecyl benzene sulphonate-protein system and the determination of proteins.

The fluorescence intensity of the morin-Al(3+) complex was greatly enhanced by proteins in the presence of sodium dodecyl benzene sulphonate (SDBS). Based on this, a new fluorimetric method for the determination of protein was developed. Under optimum conditions, the enhanced intensity of fluorescence was in proportion to the concentration of proteins in the range 1.0 x 10(-8)-1.3 x 10(-5) g/mL for bovine serum albumin (BSA), 4.0 x 10(-8)-1.2 x 10(-5) g/mL for egg albumin (EA) and 5.0 x 10(-8)-1.2 x 10(-5) g/mL for human serum albumin (HSA). Their detection limits (S:N = 3) were 5.0 x 10(-9), 1.8 x 10(-8) and 1.6 x 10(-8) g/mL, respectively. The interaction mechanism was also studied.     

Determination of difenidol hydrochloride by capillary electrophoresis with electrochemiluminescence detection

A novel and sensitive method for the determination of difenidol hydrochloride has been established using capillary electrophoresis coupled with end-column electrogenerated chemiluminescence (ECL) detection, based on the ECL reaction of tris(2,2'-bypyridine)ruthenium(II) (Ru(bpy)(3)(2+)) with the tertiary amino groups of the difenidol analyte. Parameters that affect separation and detection were optimized. Calibration curve was linear over the range from 1 x 10(-6)M to 6 x 10(-5)M with a detection limit of 1 x 10(-7)M (S/N=3). Separation of difenidol hydrochloride from clomifene citrate and lidocaine was achieved using the proposed method. This method was successfully utilized to the assay of the active ingredients of the "difenidol hydrochloride" tablets and to the investigation on the interaction of difenidol hydrochloride with hemoglobin. The number of binding sites and the binding constant were estimated as (11.2 and 2.5) x 10(3)M(-1), respectively.     

Fluorimetric detection of octopamine in high-performance liquid chromatography and its application to the assay of dopamine β-monooxygenase in human serum

A high-performance liquid chromatographic procedure is described for the determination of octopamine. The method, which is based on the separation on a microparticulate bonded strong cation-exchange resin and measurement of the native fluorescence, has been applied to give a sensitive assay of dopamine β-monooxygenase (EC 1.14.17.1) activity in human serum with tyramine as the substrate. The procedure, which has been designed for use with an-automatic sampler, has a detection limit of about 50 pmoles of octopamine, and the analysis time is approximately 10 min per sample.     

Spectrofluorimetric determination of dopamine using 1,5-bis(4,6-dicholro-1,3,5-triazinylamino) naphthalene.

A new fluorescent reagent, 1,5-bis(4,6-dichloro-1,3,5-triazinylamino)naphthalene, containing two active chlorines, was synthesized by a one-step reaction. Under the optimum conditions for the determination of dopamine, the enhanced fluorescence intensity is proportional to the dopamine concentration. The fluorescence intensity was measured at lambda(ex/em) = 400/460 nm, with and without dopamine. The linear range and detection limit for the determination of dopamine were 1.0 x 10(-7) mol/L-5.0 x 10(-5) mol/L and 4.0 x 10(-8) mol/L. This method is simple, practical, can afford good precision and accuracy and can be successfully applied to assess dopamine in injections and human serum samples.     

Simple determination of trace amounts of anionic surfactants in river water by spectrophotometry combined with solid-phase extraction

A simple and sensitive spectrophotometric method combined with solid-phase extraction (SPE) for the simultaneous determination of sodium linear-dodecylbenzenesulfonate (DBS) and sodium dodecyl sulfate (SDS) is described. The C2 (ethyl group bonded silicagel) cartridge could be repeatedly used more than 500 times for SPE, and it enabled the anionic surfactants to be concentrated by 50-fold. The calibration graph for DBS was linear in the range from 1.6 x 10(-8) M to 5.0 x 10(-7) M and for SDS from 2.0 x 10(-9) M to 3.0 x 10(-7) M. The relative standard deviation (n=5) for 5.0 x 10(-7) M DBS was 3.1% and for 2.5 x 10(-7) M SDS was 1.7%. The proposed method was applied to the simultaneous determination of DBS and SDS in river-water samples.     

Separation and detection of individual Aβ aggregates by capillary electrophoresis with laser-induced fluorescence detection

The separation and detection of individual amyloid beta (Aβ) aggregates by capillary electrophoresis with laser-induced fluorescence detection (CE-LIF) was demonstrated. Samples were prepared with either Aβ (1-40) or Aβ (1-42) peptides and were characterized by CE with ultraviolet (UV) absorbance detection and transmission electron microscopy (TEM). Using thioflavin T (ThT) in the electrophoresis buffer, electrophoresis of aggregate-containing samples (5.0-s injection) produced up to several hundred narrow (< 20 ms FWHM [full width at half maximum]) fluorescence peaks. Injection of Aβ (1-40) monomer samples resulted in no additional peaks compared with controls. The CE-LIF results were validated by bulk ThT fluorescence measurements for the same samples. The potential of laser-induced fluorescence anisotropy (LIFA) with CE to characterize individual Aβ aggregates also was investigated.     

A fluorimetric method for the determination of nucleic acids using Ce(IV) and sodium triphosphate.

A novel and stable fluorimetric method was established for the determination of nucleic acids. The proposed method is based on the reduction by nucleic acids of Ce(IV) to fluorescent Ce(III). The fluorescence intensity can be greatly increased by sodium triphosphate. The enhanced fluorescence intensity is proportional to the concentration of nucleic acids in the range 4.2 x 10(-8)-4.2 x 10(-6) g/mL for fish sperm DNA and 5.0 x 10(-8)-6.5 x 10(-6) g/mL for yeast RNA, and the detection limits (S/N = 3) are 13.5 ng/mL and 45 ng/mL, respectively. The reaction mechanism of the hydrolytic scission of nucleic acids by Ce(IV) is discussed.     

Capillary electrophoretic immunoassay for alpha-fetoprotein with chemiluminescence detection

A capillary electrophoretic immunoassay with chemiluminescence detection (CEIA-CL) using a non-competitive format for analyzing tumor marker alpha-fetoprotein (AFP) has been developed. In this method, antigen (Ag) AFP reacts with an excess amount of horseradish peroxidase (HRP)-labeled antibody (Ab*). The free Ab* and the bound Ab*-Ag complex produced in the solution are separated by CE in a separation capillary. Then they catalyze the reaction of enzyme substrate luminol and H(2)O(2) in a reaction capillary following the separation capillary. Parameters affecting the CE separation and CL detection were investigated. Under the optimal conditions, the free Ab* and the Ab*-Ag complex were well separated within 4 min, the linear range and the detection limit (S/N=3) for AFP were 5-500 ng/ml and 0.85 ng/ml (1.2 x 10(-11)M), respectively. The proposed method has been applied satisfactorily in the analysis of human sera samples.     

Determination of puerarin by capillary electrophoresis with chemiluminescence detection

A new analytical method for puerarin using capillary electrophoretic (CE) separation and chemiluminescence (CL) detection has been developed. The detection was based on the enhanced CL intensity of the reaction between luminol and potassium ferricyanide by puerarin in alkaline solution. A laboratory-built CE–CL apparatus was deployed for the puerarin detection. Under the optimal conditions, a linear range from 5.0 × 10^?8 to 2.5 × 10^?6 M and a detection limit of 1.0 × 10^?8 M (S/N = 3) for puerarin were achieved. The determination of puerarin was achieved in less than 5 min, and the proposed method was applied to the determination of puerarin in pharmaceutical, human urine and human plasma samples.