Highly filled bionanocomposites from functionalized polysaccharide nanocrystals

Cellulose and starch nanocrystals obtained from the acid hydrolysis of ramie fibers and waxy maize starch granules, respectively, were subjected to isocyanate-mediated reaction to graft polycaprolactone (PCL) chains with various molecular weights on their surface. Grafted nanoparticles were characterized by X-ray diffraction analysis and contact angle measurements. We observed that the nanoparticles kept their initial morphological integrity and native crystallinity. Nanocomposite films were processed from both unmodified and PCL-grafted nanoparticles and PCL as matrix using a casting/evaporation technique. We showed that mechanical properties of resulting films were notably different. Compared to unmodified nanoparticles, the grafting of PCL chains on the surface results in lower modulus values but significantly higher strain at break. This unusual behavior clearly reflects the originality of the reinforcing phenomenon of polysaccharide nanocrystals resulting from the formation of a percolating network thanks to chain entanglements and cocrystallization.     

Grafting of oligosaccharides onto synthetic polymer colloids

A new method to form colloidally stable oligosaccharide-grafted synthetic polymer particles has been developed. The oligosaccharides, of weight-average degree of polymerization approximately 38, were obtained by enzymatic debranching of amylopectin. Through the use of a cerium(IV)-based redox initiation process, oligosaccharide chains are grafted onto a synthetic polymer colloid comprising electrostatically stabilized poly(methyl methacrylate) or polystyrene latex particles swollen with methyl methacrylate monomer. Ce(IV) creates a radical species on these oligosaccharides, which then propagates, initially with aqueous-phase monomer, then with the methyl methacrylate monomer inside the particles. Ultracentrifugation, NMR, and total starch analyses together prove that the grafting process has occurred, with at least 7.7 wt % starch grafted and a grafting efficiency of 33%. The surfactant used in latex preparation was removed by dialysis, resulting in particles colloidally stabilized with only linear starch as a steric stabilizer. The debranched starch that comprises these oligosaccharides is found to be a remarkably effective colloidal stabilizer, albeit at low electrolyte concentration, stabilizing particles with very sparse surface coverage.     

Hydrophobic grafted and cross-linked starch nanoparticles for drug delivery

The synthesis of modified hydrophobic starch nanoparticles using long chain fatty acids was accomplished. Grafting of fatty acid on the starch was done using potassium persulphate as catalyst and the formation of graft polymer was confirmed by FTIR spectra. The thermal properties of the native and grafted starch were investigated using simultaneous TG-DTA and DSC. The graft polymerization was found to be depending on the temperature and the duration of the reaction. The modified starch nanoparticles were cross-linked with sodium tripoly phosphate for better stabilization. Morphology of the grafted starch nanoparticles was studied by SEM and AFM. Drug-loading and the controlled release of the drug from the nanoparticles was studied using indomethacin as model drug.     

Polyelectrolyte brushes grafted from cellulose nanocrystals using Cu-mediated surface-initiated controlled radical polymerization

Herein we report the synthesis of cellulose nanocrystals (CNCs) grafted with poly(acrylic acid) (PAA) chains of different lengths using Cu-mediated surface initiated-controlled radical polymerization (SI-CRP). First, poly(tert-butylacrylate) (PtBA) brushes were synthesized; then, subsequent acid hydrolysis was used to furnish PAA brushes tethered onto the CNC surfaces. The CNCs were chemically modified to create initiator moieties on the CNC surfaces using chemical vapor deposition (CVD) and continued in solvent phase in DMF. A density of initiator groups of 4.6 bromine ester groups/nm(2) on the CNC surface was reached, suggesting a dense functionalization and a promising starting point for the controlled/living radical polymerization. The SI-CRP of tert-butylacrylate proceeded in a well-controlled manner with the aid of added sacrificial initiator, yielding polymer brushes with polydispersity values typically well below 1.12. We calculated the polymer brush grafting density to almost 0.3 chains/nm(2), corresponding to high grafting densities and dense polymer brush formation on the nanocrystals. Successful rapid acid hydrolysis to remove the tert-butyl groups yielded pH-responsive PAA-polyelectrolyte brushes bound to the CNC surface. Individually dispersed rod-like nanoparticles with brushes of PtBA or PAA were clearly visualized by AFM and TEM imaging.     

Synthesis and characterization of starch-modified polyurethane

Corn starch was reacted with urethane prepolymer in order to modifying starch and preparing new hydrophobic copolymers. These copolymers were prepared by two-step reactions. The polycaprolactone terminated hexamethylene diisocyanate (HDI) (as prepolymer) was prepared by introducing diisocyanate on both ends of PCL at a molar ratio of 1:2 (PCL:HDI). The grafting was performed by addition of polycaprolactone based prepolymer to starch solution of DMSO with different weight ratio of starch and prepolymer. The samples were characterized and examined by FTIR and ¹H NMR spectroscopy, DSC analysis, and scanning electron microscopy (SEM). By introducing NCO groups onto the PCL terminals, the FTIR spectrum shows a new sharp peak, representing the NCO groups and formation of prepolymer. By grafting this prepolymer onto starch a NH and urethane band were appeared. The effect of prepolymer percentage on hydrophobicity was measured through contact angle and it was found that increases with increasing amount of prepolymer. Glass transition temperature (T_g) is also affected with increasing amount of urethane linkages. Surface morphology of modified starch was studied by SEM. It was observed that the surfaces of modified starch are rougher and disordered than the surface of unmodified starch particles. This confirms the grafting and modification of starch. This modified starch can be used as filler in biodegradable starch based polymers.     

Tailoring of bioresorbable polymers for elaboration of sugar-functionalized nanoparticles

Maleic copolymers with different contents of galactose moieties and dodecyl chains were synthesized and used as both a stabilizer and a surface coating for the preparation of poly(epsilon-caprolactone) nanoparticles by the emulsification-diffusion technique. The size of the nanoparticles was controlled by varying the initial concentration of the modified maleic copolymers. As the concentration of the latter increased, the particle size decreased, indicating that the copolymers serve as a stabilizer. Moreover, surface modification of nanoparticles was confirmed by xi-potential measurements. Nanoparticles were also shown to be recognized by a galactose-specific lectin, demonstrating the presence of galactose units on the particle surface. This approach offers opportunities for the production of novel targeted drug delivery systems.     

Ion-exchange macroporous hydrophilic gel monolith with grafted polymer brushes

The grafting of functional polymers to the pore surface of macroporous monolithic polyacrylamide cryogels was found to be an efficient and convenient method for the preparation of macroporous polyacrylamide gels, so-called cryogels (pAAm cryogels), with both controlled extent of functional group incorporated and with tailored surface chemistries. Anion-exchange polymer chains of poly(2-(dimethylamino)ethyl methacrylate) (pDMAEMA) and poly([2-(methacryloyloxy)ethyl]-trimethylammonium chloride) (pMETA), and cation-exchange polymer chains of polyacrylate have been grafted onto pAAm cryogels using potassium diperiodatocuprate as initiator. It was possible to achieve the ion-exchange capacity up to 0.2-0.5 mmol/ml. The graft polymerization did not alter the macroporous structure of the pAAm cryogel, however the flow rate of solutes through the cryogel matrix decreased with increase in the density of polymer grafted. The sorption of low-molecular-weight (metal ion, dye) and high-molecular-weight (protein) substances on the grafted monolithic pAAm column has been studied. The results indicate that a 'tentacle'-type binding of protein to grafted polymer depended on the architecture of the grafted polymer layer and took place after a certain degree of grafting has been reached. The binding of proteins by tentacle-like polymer chains allowed for increasing the binding capacity for proteins on the grafted pAAm cryogels up to 6-12 mg/ml.     

Hydroxyapatite surface modified by L-lactic acid and its subsequent grafting polymerization of L-lactide

A new method of surface modification of hydroxyapatite nanoparticles (n-HA) by surface grafting reaction of l-lactic acid and ring-opening polymerization of l-lactide (LLA) was developed. Two modified HA nanoparticles were obtained: HA modified by l-lactic acid (l-HA) and HA grafting with poly(l-lactide) (PLLA; p-HA). The modified surface of n-HA was attested by Fourier transformation infrared, (31)P MAS NMR, and thermal gravimetric analysis. The results showed that l-lactic acid could be easily grafted onto the n-HA surface by forming a Ca carboxylate bond and initiated by the hydroxyl group of the grafted l-lactic acid and LLA could be graft-polymerized onto the n-HA surface in the presence of stannous octanoate. The highest grafting amounts of l-lactic acid and PLLA were about 33 and 22 wt %, respectively. The modified HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p-HA/PLLA composite containing 15 wt % of p-HA were 67 MPa and 2.1 GPa, respectively, while those of the n-HA/PLLA composites were 45 MPa and 1.7 GPa, respectively. The elongation at the break of the l-HA/PLLA composite containing 15 wt % l-HA could reach 44%, in comparison with 6.5% of the n-HA/PLLA composites containing 15 wt % n-HA.     

Facile, efficient approach to accomplish tunable chemistries and variable biodistributions for shell cross-linked nanoparticles

The in vivo behavior of shell cross-linked knedel-like (SCK) nanoparticles is shown to be tunable via a straightforward and versatile process that advances SCKs as attractive nanoscale carriers in the field of nanomedicine. Tuning of the pharmacokinetics was accomplished by grafting varied numbers of methoxy-terminated poly(ethylene glycol) (mPEG) chains to the amphiphilic block copolymer precursors, together with chelators for the radioactive tracer and therapeutic agent (64)Cu, followed by self-assembly into block copolymer micelles and chemical cross-linking throughout the shell regions. (64)Cu-radiolabeling was then performed to evaluate the SCKs in vivo by means of biodistribution experiments and positron emission tomography (PET). It was found that the blood retention of PEGylated SCKs could be tuned, depending on the mPEG grafting density and the nanoparticle surface properties. A semiquantitative model of the density of mPEG surface coverage as a function of in vivo behavior was applied to enhance the understanding of this system.     

Radical graft polymerization of styrene sulfonate on poly(ethylene terephthalate) films for ACL applications: "grafting from" and chemical characterization

The purpose of this study is to develop a reliable method of functionalizing poly(ethylene terephthalate) with bioactive polymers to produce a "biointegrable" artificial anterior cruciate ligament. Radical graft polymerization of the sodium salt of styrene sulfonate (NaSS) onto poly(ethylene terephthalate) (PET) films was performed using the "grafting from" technique. Prior to the grafting, the surfaces of poly(ethylene terephthalate) films were activated by ozonation to generate peroxide and hydroperoxide reactive species on the PET film surfaces. The radical polymerization of NaSS was initiated by thermal decomposition of the hydroperoxides. The grafted PET surfaces were characterized by a toluidin blue colorimetric method, X-ray photoelectron spectroscopy, contact angle measurements, and atomic force microscopy. The influence of ozonation time, monomer concentration, and temperature on NaSS grafting ratios was examined. A total of 30 min of ozonation followed by grafting from a 15% NaSS solution at 70 degrees C for 90 min or more resulted in attachment of poly(NaSS) chains to the PET film surfaces.     

Biodegradation of poly(epsilon-caprolactone)/starch blends and composites in composting and culture environments: the effect of compatibilization on the inherent biodegradability of the host polymer

The biodegradability of poly(epsilon-caprolactone) (PCL) was studied in blends and composites of modified and granular starch. Four types of PCL-starch compositions were prepared: (i) PCL-granular starch blends; (ii) hydrophobic coating of starch particles by n-butylisocyanate (C(4) starch) and octadecyltrichlorosilane (C(18) starch), followed by melt blending with PCL; (iii) PCL-starch blends compatibilized by PCL-g-dextran grafted copolymer (PGD); and (iv) PCL-grafted starch particles (PGS) as obtained by in situ ring-opening polymerization of caprolactone (CL) initiated directly from hydroxyl functions at the granular starch surface. Biodegradability of these materials was measured by monitoring the percentage of weight loss in composting and the rate of fungal colonization when samples were used as a sole carbon source for fungus (A. niger). Intrinsic viscosity [eta] of host PCL chains was measured after extraction of composted samples in boiled chloroform. SEM was used to study the surface morphology after compost incubation of the samples. The inherent biodegradability of host polymer was enhanced with surface compatibilization during composting for longer incubation. It was observed that the weight loss during composting increased with the decrease in interfacial tension between filler and polymer. In general, it was concluded that inherent biodegradability does not depend very significantly on the concentration of starch in the polyester matrix, but on the compatibilization efficiency. The effect of the PCL fraction in the graft copolymer, when used as compatibilizer, was also studied on the biodegradability of the host polymer.     

Production of starch foams by twin-screw extrusion: effect of maleated poly(butylene adipate-co-terephthalate) as a compatibilizer

Free-radical-initiated grafting of maleic anhydride (MA) onto poly(butylene adipate-co-terephthalate) (PBAT), a biodegradable aliphatic-aromatic copolyester, was performed by reactive extrusion. 2,5-Dimethyl-2,5-di(tert-butylperoxy)hexane was used as the free-radical initiator. The peroxide concentration was varied between 0.0 and 0.5 wt % at 3.0 wt % MA concentration; the MA concentration was varied between 1.0 and 5.0 wt % at 0.5 wt % peroxide concentration. The reaction temperature was maintained at 185 degrees C for all experiments. Under these conditions, between 0.194% and 0.691% MA was grafted onto the polyester backbone. Size-exclusion chromatography, melt flow index, intrinsic viscosity measurements, thermal gravimetric analysis, and differential scanning calorimetry were used to characterize the maleated copolyester. Increasing the initiator concentration at a constant MA concentration of 3% resulted in an increase in the grafting of MA while decreasing the molecular weight of the resulting polymer. Increasing the feed MA concentration also increased the grafting percentage. The maleation of the polyester proved to be very efficient in promoting strong interfacial adhesion with high amylose cornstarch in starch foams as prepared by melt blending. Thus, the use of maleated copolyester as a compatibilizer between starch and PBAT allowed the reduction of the density of resulting starch foams to approximately 21 kg/m3 and improved the resilience from 84% to as high as 95%. Also, the resulting starch foams exhibited improved hydrophobic properties in terms of lower weight gain and higher dimensional stability on moisture sorption.     

Impact of down-regulation of starch branching enzyme IIb in rice by artificial microRNA- and hairpin RNA-mediated RNA silencing

The inactivation of starch branching IIb (SBEIIb) in rice is traditionally associated with elevated apparent amylose content, increased peak gelatinization temperature, and a decreased proportion of short amylopectin branches. To elucidate further the structural and functional role of this enzyme, the phenotypic effects of down-regulating SBEIIb expression in rice endosperm were characterized by artificial microRNA (amiRNA) and hairpin RNA (hp-RNA) gene silencing. The results showed that RNA silencing of SBEIIb expression in rice grains did not affect the expression of other major isoforms of starch branching enzymes or starch synthases. Structural analyses of debranched starch showed that the doubling of apparent amylose content was not due to an increase in the relative proportion of amylose chains but instead was due to significantly elevated levels of long amylopectin and intermediate chains. Rices altered by the amiRNA technique produced a more extreme starch phenotype than those modified using the hp-RNA technique, with a greater increase in the proportion of long amylopectin and intermediate chains. The more pronounced starch structural modifications produced in the amiRNA lines led to more severe alterations in starch granule morphology and crystallinity as well as digestibility of freshly cooked grains. The potential role of attenuating SBEIIb expression in generating starch with elevated levels of resistant starch and lower glycaemic index is discussed.     

Modeling and experimental investigation of rheological properties of injectable poly(lactide ethylene oxide fumarate)/hydroxyapatite nanocomposites

Injectable multiphasic polymer/ceramic composites are attractive as bioresorbable scaffolds for bone regeneration because they can be cross-linked in situ and are osteoconductive. The injectability of the composite depends on the nanoparticle content and the energetic interactions at the polymer/particle interface. The objective of this research was to determine experimentally the rheological properties of the PLEOF/apatite composite as an injectable biomaterial and to compare the viscoelastic response with the predictions of a linear elastic dumbbell model. A degradable in situ cross-linkable terpolymer based on low molecular weight poly(L-lactide) and poly(ethylene oxide) linked by unsaturated fumarate groups is synthesized. The poly(L-lactide-co-ethylene oxide-co-fumarate) (PLEOF) terpolymer interacts with the surface of the apatite nanoparticles by polar interactions and hydrogen bonding. A kinetic model is developed that takes into account the adsorption/desorption of polymer chains to/from the nanoparticle surface. Rheological properties of the aqueous dispersion of PLEOF terpolymer reinforced with nanosized hydroxyapatite (HA) particles are investigated using mechanical rheometry. To this end, we performed a series of rheological experiments on un-cross-linked PLEOF reinforced with different volume fractions of HA nanoparticles. The results demonstrate that the observed nonlinear viscoelasticity at higher shear rates is controlled by the energetic interactions between the polymer chains and dispersed particle aggregates and by the rate of the adsorption/desorption of the chains to/from the surface of the nanoparticles.     

Biopolymer-protected CdSe nanoparticles

A synthetic procedure for the encapsulation of cadmium selenide (CdSe) nanoparticles in a sago starch matrix is introduced. The nanocomposite was investigated using structural, spectroscopic, and thermal methods. TEM micrographs of the nanocomposite showed spherical CdSe particles of 4-5 nm in size coated with a biopolymer layer. The absorption edges of both the aqueous solution and the thin film of the CdSe-starch nanocomposite were shifted toward lower wavelengths in comparison to the value of the bulk semiconductor. Infrared measurements revealed that the interaction of CdSe nanoparticles and starch chains takes place via OH groups. Although the onset of the temperature of decomposition of CdSe-starch nanocomposite is lower than that of the pure matrix, thermogravimetric analysis also showed that introduction of CdSe nanoparticles significantly reduced starch degradation rate leading to high residual mass at the end of the degradation process.     

Nanoreinforcement of poly(propylene fumarate)-based networks with surface modified alumoxane nanoparticles for bone tissue engineering

A novel composite material has been fabricated for bone tissue engineering scaffolds utilizing the biodegradable polymer poly(propylene fumarate)/poly(propylene fumarate)-diacrylate (PPF/PPF-DA) and surface-modified carboxylate alumoxane nanoparticles. Various surface-modified nanoparticles were added to the polymer including a surfactant alumoxane, an activated alumoxane, a mixed alumoxane containing both activated and surfactant groups, and a hybrid alumoxane containing both groups within the same substituent. These nanocomposites, as well as polymer resin and unmodified boehmite composites, underwent flexural and compressive mechanical testing and were examined using electron microscopy. Hybrid alumoxane nanoparticles dispersed in PPF/PPF-DA exhibited over a 3-fold increase in flexural modulus at 1 wt % loading compared to polymer resin alone. No significant loss of flexural or compressive strength was observed with increased loading of hybrid alumoxane nanoparticles. These dramatic improvements in flexural properties may be attributed to the fine dispersion of nanoparticles into the polymer and increased covalent interaction between polymer chains and surface modifications of nanoparticles.     

Synthesis of poly-(ε)-caprolactone grafted starch co-polymers by ring-opening polymerisation using silylated starch precursors

Poly-(ε)-caprolactone grafted corn starch co-polymers were synthesized using a hydrophobised silylated starch precursor. The silylation reaction was performed using hexamethyl disilazane (HMDS) as the reagent in DMSO at 70 °C. Silylated starch with a degree of substitution (DS) between 0.45 and 0.7 was obtained. ε-Caprolactone is grafted to silylated starch by a ring-opening polymerisation catalysed by Al(OiPr)₃ in THF at 50 °C. The grafting efficiency varies between 28% and 58%, the remainder being homopolymers of ε-caprolactone. The DS of the polycaprolactone graft is between 0.21 and 0.72. The poly-(ε)-caprolactone side chains consist of 40–55 monomer units and is a function of the reagent intakes. Experiments with native starch under similar conditions do not result in the desired poly-(ε)-caprolactone grafted corn starch co-polymers and unreacted starch was recovered after work-up. Removal of the silyl groups of the poly-(ε)-caprolactone grafted starch co-polymers is possible using a mild acid treatment with diluted hydrochloric acid in THF at room temperature.     

Synthesis and characterization of the biodegradable polycaprolactone-graft-chitosan amphiphilic copolymers

A novel synthetic approach to biodegradable amphiphilic copolymers based on poly (epsilon-caprolactone) (PCL) and chitosan was presented, and the prepared copolymers were used to prepare nanoparticles successfully. The PCL-graft-chitosan copolymers were synthesized by coupling the hydroxyl end-groups on preformed PCL chains and the amino groups present on 6-O-triphenylmethyl chitosan and by removing the protective 6-O-triphenylmethyl groups in acidic aqueous solution. The PCL content in the copolymers can be controlled in the range of 10-90 wt %. The graft copolymers were thoroughly characterized by 1H NMR, 13C NMR, FT-IR and DSC. The nanoparticles made from the graft copolymers were investigated by 1H NMR, DLS, AFM and SEM measurements. It was found that the copolymers could form spherical or elliptic nanoparticles in water. The amount of available primary amines on the surface of the prepared nanoparticles was evaluated by ninhydrin assay, and it can be controlled by the grafting degree of PCL.     

Antisense downregulation of the barley limit dextrinase inhibitor modulates starch granule size distribution, starch composition and amylopectin structure

The barley protein limit dextrinase inhibitor (LDI), structurally related to the alpha-amylase/trypsin inhibitor family, is an inhibitor of the starch debranching enzyme limit dextrinase (LD). In order to investigate the function of LDI, and the consequences for starch metabolism of reduced LDI activity, transgenic barley plants designed to downregulate LDI by antisense were generated. Homozygous antisense lines with reduced LDI protein level and activity were analysed and found to have enhanced free LD activity in both developing and germinating grains. In addition the antisense lines showed unpredicted pleiotropic effects on numerous enzyme activities, for example, alpha- and beta-amylases and starch synthases. Analysis of the starch showed much reduced numbers of the small B-type starch granules, as well as reduced amylose relative to amylopectin levels and reduced total starch. The chain length distribution of the amylopectin was modified with less of the longer chains (>25 units) and enhanced number of medium chains (10-15 units). These results suggest an important role for LDI and LD during starch synthesis as well as during starch breakdown.     

Isocyanate crosslinked reactive starch nanoparticles for thermo-responsive conducting applications

Hydrophobic nanoparticles and nanocomposite films of 1,4-hexamethylene diisocyanate (HMDI)-modified starch nanoparticles (SNPs) have been synthesized at ambient temperatures. The platelet-like starch nanocrystals become pseudospherical after modification with HMDI and the size increases or decreases depending on diisocyanate concentration compared to the ungrafted particles as revealed by transmission electron microscopy (TEM) results. The obtained nanocrystals were characterized by means of the FT-IR and X-ray diffraction (XRD) techniques. When compared with the hydrophobic performance of the unmodified starch nanocrystals, that of crosslinked starch nanocrystals significantly increased. X-ray diffraction reveals that the crystalline structure of modified starch nanocrystals was preserved. The resulting hydrophobic starch nanoparticles are versatile precursors to the development of nanocomposites. The polyether-polyurethane crosslinked with SNPs nanocomposite film exhibited thermo-responsive electrical conductivity.