Assembly of collagen fibril meshes using gold nanoparticles functionalized with tris(hydroxymethyl)phosphine-alanine as multivalent cross-linking agents

We report on the use of tris(hydroxymethyl)phosphine-alanine (THPAL) functionalized gold nanoparticles as a multivalent cross-linking agent to assemble collagen fibrils into a mesh-like structure. Atomic force microscopy (AFM) was used for characterization of the structure after adsorption onto an atomically flat mica substrate, revealing a mesh-like construct in which the collagen fibrils and the gold nanoparticles interact to form interconnected nodes measuring from 100 to 500 nm. As expected, the density of the collagen mesh can be increased with a higher initial concentration of gold nanoparticles. The maximum thickness of the meshes (～ 20 nm) obtained through cross-sectional height measurements confirms that the adsorbed structure consists of a single layer of collagen fibrils/gold nanoparticles assembled in two-dimensions. We propose that the capability of gold nanoparticles functionalized with the THPAL to bind to several collagen fibrils combined with the large persistence length of the fibrils, which was reported to be in the hundreds of nanometer range, are determinant factors for the preferential 2D growth of the mesh in solution.     

Atomic Force Microscopy of Biological Membranes

Atomic force microscopy (AFM) is an ideal method to study the surface topography of biological membranes. It allows membranes that are adsorbed to flat solid supports to be raster-scanned in physiological solutions with an atomically sharp tip. Therefore, AFM is capable of observing biological molecular machines at work. In addition, the tip can be tethered to the end of a single membrane protein, and forces acting on the tip upon its retraction indicate barriers that occur during the process of protein unfolding. Here we discuss the fundamental limitations of AFM determined by the properties of cantilevers, present aspects of sample preparation, and review results achieved on reconstituted and native biological membranes.     

Fabrication of a new substrate for atomic force microscopic observation of DNA molecules from an ultrasmooth sapphire plate.

A new stable substrate applicable to the observation of DNA molecules by atomic force microscopy (AFM) was fabricated from a ultrasmooth sapphire (alpha-Al2O3 single crystal) plate. The atomically ultrasmooth sapphire as obtained by high-temperature annealing has hydrophobic surfaces and could not be used for the AFM observation of DNA. However, sapphire treated with Na3PO4 aqueous solution exhibited a hydrophilic character while maintaining a smooth surface structure. The surface of the wet-treated sapphire was found by x-ray photoelectron spectroscopy and AFM to be approximately 0.3 nm. The hydrophilic surface character of the ultrasmooth sapphire plate made it easy for DNA molecules to adhere to the plate. Circular molecules of the plasmid DNA could be imaged by AFM on the hydrophilic ultrasmooth sapphire plate.     

Atomic force microscopy-based detection of binding and cleavage site of matrix metalloproteinase on individual type II collagen helices

Type II tropocollagen molecules were reacted with matrix metalloproteinase 8 (MMP-8) and the binding sites as well as the cleavage site of MMP-8 were detected on individual molecules using atomic force microscopy (AFM). Approximately 300-nm-long coiled-coil tropocollagen molecules were straightened and immobilized on an atomically flat surface for detection by AFM. The direct visualization of individual collagen molecules revealed heterogeneous characteristics of MMP-8:collagen complexes. We observed that there existed multiple MMP-8 nonspecific binding sites on the collagen molecules, but cleavage always took place at a unique site. When collagen molecules, straightened and immobilized on the surface, were reacted with MMP-8, a site of cleavage appeared as a gap in stretched molecules. This is the first report to visually show direct collagenase:collagen interactions using AFM. The described AFM-based analysis has potential as a protein analysis tool for understanding a complex mechanism of enzyme:substrate interactions.     

Preparation of Mica Supported Lipid Bilayers for High Resolution Optical Microscopy Imaging

Supported lipid bilayers (SLBs) are widely used as a model for studying membrane properties (phase separation, clustering, dynamics) and its interaction with other compounds, such as drugs or peptides. However SLB characteristics differ depending on the support used. Commonly used techniques for SLB imaging and measurements are single molecule fluorescence microscopy, FCS and atomic force microscopy (AFM). Because most optical imaging studies are carried out on a glass support, while AFM requires an extremely flat surface (generally mica), results from these techniques cannot be compared directly, since the charge and smoothness properties of these materials strongly influence diffusion. Unfortunately, the high level of manual dexterity required for the cutting and gluing thin slices of mica to the glass slide presents a hurdle to routine use of mica for SLB preparation. Although this would be the method of choice, such prepared mica surfaces often end up being uneven (wavy) and difficult to image, especially with small working distance, high numerical aperture lenses. Here we present a simple and reproducible method for preparing thin, flat mica surfaces for lipid vesicle deposition and SLB preparation. Additionally, our custom made chamber requires only very small volumes of vesicles for SLB formation. The overall procedure results in the efficient, simple and inexpensive production of high quality lipid bilayer surfaces that are directly comparable to those used in AFM studies.     

The investigation of Protein A and Salmonella antibody adsorption onto biosensor surfaces by atomic force microscopy

The investigation of Protein A and antibody adsorption on surfaces in a biological environment is an important and fundamental step for increasing biosensor sensitivity and specificity. The atomic force microscope (AFM) is a powerful tool that is frequently used to characterize surfaces coated with a variety of molecules. We used AFM in conjunction with scanning electron microscopy to characterize the attachment of protein A and its subsequent binding to the antibody and Salmonella bacteria using a gold quartz crystal. The rms roughness of the base gold surface was determined to be approximately 1.30 nm. The average step height change between the solid gold and protein A layer was approximately 3.0 +/- 1.0 nm, while the average step height of the protein A with attached antibody was approximately 6.0 +/- 1.0 nm. We found that the antibodies did not completely cover the protein A layer, instead the attachment follows an island model. Salt crystals and water trapped under the protein A layer were also observed. The uneven adsorption of antibodies onto the biosensor surface might have led to a decrease in the sensitivity of the biosensor. The presence of salt crystals and water under the protein A layer may deteriorate the sensor specificity. In this report, we have discussed the application and characterization of protein A bound to antibodies which can be used to detect bacterial and viral pathogens.     

AFM and impedance spectroscopy characterization of the immobilization of antibodies on indium-tin oxide electrode through self-assembled monolayer of epoxysilane and their capture of Escherichia coli O157:H7

The microscopic surface molecular structures and macroscopic electrochemical impedance properties of the epoxysilane monolayer and anti-Escherichia coli antibody layer on an indium-tin oxide (ITO) electrode surface were studied in this paper. Characterization of stepwise changes in microscopic features of the surfaces and electrochemical properties upon the formation of each layer were carried out using both atomic force microscopy (AFM) and electrochemical impedance spectroscopy in the presence of [Fe(CN)6](3-/4-) as a redox couple. AFM images of the self-assembled monolayer (SAM) evidenced the dense, complete, and homogeneous morphology of the epoxysilane monolayer on the ITO surface. The uniformity of the epoxysilane SAM allowed antibodies to attach to the epoxy surface groups of the silanes in a similarly uniform fashion. The effects of epoxysilane monolayer and the antibody layer on the electrochemical properties of the electrode were quantitatively analyzed in terms of double layer capacitance, electron transfer resistance, Warburg impedance and solution resistance using Randles model as the equivalent circuit. It was demonstrated that the epoxysilane monolayer and the antibody layer act as barriers for the electron transfer between the electrode surface and the redox species in the solution, resulting in most significant increases in the electron transfer resistance compared to all the electric elements. Immunoreaction with E. coli O157:H7 cells demonstrated specific recognition of the immobilized anti-E. coli antibodies as evidenced by AFM imaging and impedance spectroscopy. It was found that the binding of E. coli cells mainly affected the electron transfer resistance and Warburg impedance.     

Reactive thin polymer films as platforms for the immobilization of biomolecules

Spin-coated thin films of poly(N-hydroxysuccinimidyl methacrylate) (PNHSMA) on oxidized silicon and gold surfaces were investigated as reactive layers for obtaining platforms for biomolecule immobilization with high molecular loading. The surface reactivity of PNHSMA films in coupling reactions with various primary amines, including amine-terminated poly(ethylene glycol) (PEG-NH2) and fluoresceinamine, was determined by Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS), fluorescence microscopy, and ellipsometry measurements, respectively. The rate constants of PEG-NH2 attachment on the PNHSMA films were found to be significantly increased compared to the coupling on self-assembled monolayers (SAMs) of 11,11'-dithiobis(N-hydroxysuccinimidylundecanoate) (NHS-C10) on gold under the same conditions. More significantly, the PEG loading observed was about 3 times higher for the polymer thin films. These data indicate that the coupling reactions are not limited to the very surface of the polymer films, but proceed into the near-surface regions of the films. PNHSMA films were shown to be stable in contact with aqueous buffer; the swelling analysis, as performed by atomic force microscopy (AFM), indicated a film thickness independent swelling of approximately 2 nm. An increased loading was also observed by surface plasmon resonance for the covalent immobilization of amino-functionalized probe DNA. Hybridization of fluorescently labeled target DNA was successfully detected by fluorescence microscopy and surface plasmon resonance enhanced fluorescence spectroscopy (SPFS), thereby demonstrating that thin films of PNHSMA comprise an attractive and simple platform for the immobilization of biomolecules with high densities.     

Submicron patterning of DNA oligonucleotides on silicon

The covalent attachment of DNA oligonucleotides onto crystalline silicon (100) surfaces, in patterns with submicron features, in a straightforward, two-step process is presented. UV light exposure of a hydrogen-terminated silicon (100) surface coated with alkenes functionalized with N-hydroxysuccinimide ester groups resulted in the covalent attachment of the alkene as a monolayer on the surface. Submicron-scale patterning of surfaces was achieved by illumination with an interference pattern obtained by the transmission of 248 nm excimer laser light through a phase mask. The N-hydroxysuccinimide ester surface acted as a template for the subsequent covalent attachment of aminohexyl-modified DNA oligonucleotides. Oligonucleotide patterns, with feature sizes of 500 nm, were reliably produced over large areas. The patterned surfaces were characterized with atomic force microscopy, scanning electron microscopy, epifluorescence microscopy and ellipsometry. Complementary oligonucleotides were hybridized to the surface-attached oligonucleotides with a density of 7 × 10¹² DNA oligonucleotides per square centimetre. The method will offer much potential for the creation of nano- and micro-scale DNA biosensor devices in silicon.     

Effect of the covalently linked fatty acid 18-MEA on the nanotribology of hair's outermost surface

Highly ordered lipids adsorbed or grafted on surfaces are known to provide protection and lubrication custom engineered surfaces. We have used atomic force microscopy (AFM) to measure adhesion and frictional properties of the outermost surfaces of a variety of human hairs with the aim of both understanding the role of 18-methyleicosanoic acid (18-MEA), an unusual branched-chain fatty acid covalently bound to the cuticle surface, and investigating how treatments or the ethnic origin affect this layer. Results show that an unmodified silicon nitride AFM tip is able to detect changes at the hair surface that can be related to the absence or presence of this layer due to treatment conditions and in particular that this monolayer has a lubricant effect.     

Slow cellular dynamics in MDCK and R5 cells monitored by time-lapse atomic force microscopy.

We have examined dynamic events that occur on a time scale of minutes in an epithelial monolayer of Madine-Darby Canine Kidney (MDCK) cells and in ras-transformed MDCK cells by atomic force microscopy (AFM). Cells were imaged under physiological conditions, and time-lapse movies representing approximately 60 s real time per frame were assembled. In normal MDCK cells, two types of protrusions in the apical plasma membrane exhibit dynamic behavior. First, smooth bulges formed transiently over the time scale of minutes to tens of minutes. Second, spike-like protrusions appear initially as bulges, extend well above the apical surface and, finally, seem to detach. R5, an oncogenic transformant derived from MDCK cells, grows very flat on glass. During AFM imaging, these cells sometimes round up and detach from the substrate. In light microscopic observations of parallel preparations, cells rarely detach, suggesting that this is an active response of these cells to irritation by the AFM tip. R5 cells often extend processes that are supported by actin stress fibers. During imaging with the AFM, these processes withdraw at a rate of 1-5 microns/min, similar to that observed by light microscopy. During the withdrawal, movement of the stress fibers can be clearly seen. In the flat periphery of these cells, the transport of intracellular particles along cytoskeletal elements was seen. In addition, we have observed two types of wave-like movements through the cell, which appear to be an organized rearrangement of cytoplasm. One type of wave moves radially out from center of the cell while the other moves circularly along the cell periphery.     

Application of atomic force microscopy and grating coupler for the characterization of biosensor surfaces

Atomic force microscopy (AFM) and an optical grating coupler system were used to improve the understanding of the biosensing layer on a Ta(2)O(5)-light-guiding surface. Exemplary, we investigated the immobilization of the protein avidin, the subsequent binding of biotinylated oligonucleotides and hybridization of a complementary 12-mer. The AFM measurements revealed the height of approximately 1.6 nm for a single avidin molecule, while the thickness of the avidin layer on the biosensor surface seemed to be 2.8-3.0 nm. This result lead to the conclusion that the protein was not forming a simple monolayer. However, the thickness of the avidin layer could not be determined directly, but only after shifting of protein by the tip of the AFM leading to grooves of 1 micro m(2) and approximately 3 nm depth. As the height of oxide particles forming the waveguide surface was also in the range of 1.5 nm, the depth of these grooves could also be a result of the deposition of proteins on top of the oxide particles. This was consistent with the increased roughness of the surface after protein binding. Thus, investigations with the grating coupler were used to determine quantitatively the amount of immobilized avidin. On a biotinylated surface the amount of immobilized avidin lead to the assumption of a complete monolayer, whereas simple adsorption proved to be less efficient. A binding ratio of 1:1.3 for avidin and a biotinylated oligonucleotide was achieved. Up to 83% of the bound single strand were accessible for a subsequent hybridization reaction with a 12-mer. These results supported the model of avidin being deposited mainly on top of the oxide particles leading to the picture of a 'rough' complete protein monolayer, which was postulated from the AFM investigations.     

Surface engineering: optimization of antigen presentation in self-assembled monolayers.

The formation of self-assembled monolayers (SAMs) on gold surfaces containing an antigenic peptide (NANP)6 and HS(CH2)11OH, and the specific binding of a monoclonal antibody to these layers were investigated by surface plasmon resonance (SPR). Peptides were synthesized by solid-state phase synthesis and were linked either to cysteine or to an alkyl-thiol to allow covalent attachment to gold. The content of the peptide in the SAMs was systematically varied, and the binding properties of the monoclonal antibody were compared with those measured by microcalorimetry in solution. At a critical peptide concentration in the SAM an optimal antibody binding and complete surface coverage was attained. At lower peptide concentrations, the amount of adsorbed antibody decreased; at higher peptide concentrations, the binding constant decreased. These effects can be explained if the accessibility of the antigenic epitopes depends on the peptide density. Addition of free antigen induced the desorption of bound antibodies and allowed accurate measurements of the dissociation rate constant. Binding constants obtained from steady-state measurements and from measurements of the kinetic rate constants were compared.     

Patterning of photosensitive polyimide LB film and its application in the fabrication of biomolecular microphotodiode array

Ultra thin film of photosensitive polyimide having benzene and sulfonyloxyimide moieties in the main chain was prepared using a Langmuir-Blodgett (LB) technique, and then micro array pattern of the polyimide LB film on a gold substrate was obtained by deep UV lithographic technique. In order to array cytochrome c molecules along the micro-patterned gold substrate, the well-characterized monolayer of cytochrome c was immobilized with a mixed monolayer of 11-mercaptoundecanoic acid (11-MUDA) and decanethiol. The redox activity and electron transfer between cytochrome c molecular center and gold electrode interface for the self-assembled cytochrome c monolayer were investigated by cyclic voltammetry measurement. Biomolecular photodiode consisting of cytochrome c and green fluorescent protein (GFP) onto the patterned gold substrate was fabricated by self-assembly process. The integration and morphology of cytochrome c and GFP were studied from the measurements of atomic force microscopy (AFM) and fluorescence emission. Especially, current-voltage characteristics of the protein multilayers were investigated by scanning tunneling microscopy (STM) and its application in biomolecular photodiode was also examined.     

A protein A-based orientation-controlled immobilization strategy for antibodies using nanometer-sized gold particles and plasma-polymerized film

A novel protein A (PA)-based strategy for the orientation-controlled immobilization of antibodies using nanometer-sized gold (Nano-gold) particles and an amine-terminated plasma-polymerized film (PPF) has been proposed. A quartz crystal microbalance was fabricated, accordingly, coupling with haptoglobin (HP) antibody followed by HP immunoassay, as a model test system. The crystal was modified with plasma-polymerized n-butyl amine film to deposit Nano-gold particles and PA, on which HP antibodies were immobilized. The surface topology of the as-prepared crystal was characterized by use of scanning electron microscopy. In contrast to the traditional flat gold surface, the assembled Nano-gold particle monolayer could allow PA molecules bound with higher bioactivity and loading amount (density), achieving better antibody-binding capabilities. Results indicate that immunosensors prepared using the developed PPF-Nano-gold-PA binding procedure exhibit increased analytical performance compared with those produced using the direct PA binding procedure and the PPF-based glutaraldehyde cross-linking procedure. A HP serum concentration as low as 0.41 nM can be determined by this new system. Regenerated simply by rinsing in the acid buffer, the proposed sensor can achieve up to 11 assay cycles without significant loss of sensitivity.     

Tracking mechanics and volume of globular cells with atomic force microscopy using a constant-height clamp

To understand the role of physical forces at a cellular level, it is necessary to track mechanical properties during cellular processes. Here we present a protocol that uses flat atomic force microscopy (AFM) cantilevers clamped at constant height, and light microscopy to measure the resistance force, mechanical stress and volume of globular animal cells under compression. We describe the AFM and cantilever setup, live cell culture in the AFM, how to ensure stability of AFM measurements during medium perfusion, integration of optical microscopy to measure parameters such as volume and track intracellular dynamics, and interpretation of the physical parameters measured. Although we use this protocol on trypsinized interphase and mitotic HeLa cells, it can also be applied to other cells with a relatively globular shape, especially animal cells in a low-adhesive environment. After a short setup phase, the protocol can be used to investigate approximately one cell per hour.     

Thermodynamic studies on the adsorption of fibronectin adhesion-promoting peptide on nanothin films of poly(2-vinylpyridine) by SPR

This paper describes a methodology for preparing uniform, nanothin polymer films for the study of biomolecule adsorption by surface plasmon resonance spectroscopy (SPR). The methodology combines molecular self-assembly of alkanethiols on gold with surface-confined atom transfer radical polymerization (ATRP). Poly(2-vinylpyridine) was chosen to demonstrate the methodology, and growth kinetics were studied by ex situ ellipsometry. Atomic force microscopy (AFM) indicated that the polymer films were uniform with RMS roughness of approximately 0.5 nm. Subsequent SPR measurements were done to determine thermodynamic adsorption properties (deltaG, deltaH, and deltaS) between fibronectin adhesion-promoting peptide and the surface-confined poly(2-vinylpyridine) at 15, 20, and 25 degrees C. The flexibility in synthesis conditions and the opportunities for manipulating film thicknesses and graft densities that ATRP provides to grow polymer films from gold surfaces holds advantages over conventional spin-coating and grafting to approaches in the design of model polymer films for biomolecule adsorption studies. These advantages are described.     

Nanoscale Pulling of Type IV Pili Reveals Their Flexibility and Adhesion to Surfaces over Extended Lengths of the Pili

Type IV pili (T4P) are very thin protein filaments that extend from and retract into bacterial cells, allowing them to interact with and colonize a broad array of chemically diverse surfaces. The physical aspects that allow T4P to mediate adherence to many different surfaces remain unclear. Atomic force microscopy (AFM) nanoscale pulling experiments were used to measure the mechanical properties of T4P of a mutant strain of Pseudomonas aeruginosa PAO1 unable to retract its T4P. After adhering bacteria to the end of an AFM cantilever and approaching surfaces of mica, gold, or polystyrene, we observed adhesion of the T4P to all of the surfaces. Pulling of single and multiple T4P on retraction of the cantilever from the surfaces could be described using the worm-like chain (WLC) model. Distinct peaks in the measured distributions of the best-fit values of the persistence length L_p on two different surfaces provide strong evidence for close-packed bundling of very flexible T4P. In addition, we observed force plateaus indicating that adhesion of the T4P to both hydrophilic and hydrophobic surfaces occurs along extended lengths of the T4P. These data shed new light, to our knowledge, on T4P flexibility and support a low-affinity, high-avidity adhesion mechanism that mediates bacteria-surface interactions.     

Application of atomic force microscopy to the study of micromechanical properties of biological materials

Atomic force microscopy (AFM) has been used to study the micromechanical properties of biological systems. Its unique ability to function both as an imaging device and force sensor with nanometer resolution in both gaseous and liquid environments has meant that AFM has provided unique insights into the mechanical behaviour of tissues, cells and single molecules. As a surface scanning device, AFM can map properties such as adhesion and the Young's modulus of surfaces. As a force sensor and nanoindentor AFM can directly measure properties such as the Young's modulus of surfaces or the binding forces of cells. As a stress-strain gauge AFM can study the stretching of single molecules or fibres and as a nanomanipulator it can dissect biological particles such as viruses or DNA strands. The present paper reviews key research that has demonstrated the versatility of AFM and how it can be exploited to study the micromechanical behaviour of biological materials.     

Atomic force microscopy and force spectroscopy study of Langmuir-Blodgett films formed by heteroacid phospholipids of biological interest

Langmuir-Blodgett (LB) films of two heteroacid phospholipids of biological interest 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphoethanolamine (POPE) and 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC), as well as a mixed monolayer with chi(POPC)=0.4, were transferred onto mica in order to investigate by a combination of atomic force microscopy (AFM) and force spectroscopy (FS) their height, and particularly, their nanomechanical properties. AFM images of such monolayers extracted at 30 mN m(-1) revealed a smooth and defect-free topography except for the POPE monolayer. Since scratching such soft monolayers in contact mode was proved unsuccessful, their molecular height was measured by means of the width of the jump present in the respective force-extension curves. While for pure POPC a small jump occurs near zero force, for the mixed monolayer with chi(POPC)=0.4 the jump occurs at approximately 800 pN. Widths of approximately 2 nm could be established for POPC and chi(POPC)=0.4, but not for POPE monolayer at this extracting pressure. Such different mechanical stability allowed us to directly measure the threshold area/lipid range value needed to induce mechanical stability to the monolayers. AFM imaging and FS were next applied to get further structural and mechanical insight into the POPE phase transition (LC-LC') occurring at pressures >36.5 mN m(-1). This phase transition was intimately related to a sudden decrease in the area/molecule value, resulting in a jump in the force curve occurring at high force ( approximately 1.72 nN). FS reveals to be the unique experimental technique able to unveil structural and nanomechanical properties for such soft phospholipid monolayers. The biological implications of the nanomechanical properties of the systems under investigation are discussed considering that the annular phospholipids region of some transmembrane proteins is enriched in POPE.