Direct electrochemistry of glucose oxidase and electrochemical biosensing of glucose on quantum dots/carbon nanotubes electrodes

Because of their unique chemical, physical and electronic properties, Quantum dots (QDs) and carbon nanotubes (CNTs) are now extremely attractive and important nanomaterials in bioanalytical applications. In this work, CdTe QDs with the size of about 3 nm were prepared and a novel electrochemical biosensing platform of glucose based on CdTe/CNTs electrode was explored. This CdTe/CNTs electrode was prepared by first mixing CdTe QDs, CNTs, Nafion, and glucose oxidase (GOD) in appropriate amounts and then modifying this mixture on the glass carbon electrode (GC). Transmission electron microscopy (TEM) was used to observe the dispersion of CdTe QDs on carbon nanotubes and cyclic voltammetry (CV) was used to investigate the electrochemical behavior of the CdTe/CNTs electrode. A pair of well-defined quasi-reversible redox peaks of glucose oxidase were obtained at the CdTe/CNTs based enzyme electrode by direct electron transfer between the protein and the electrode. The immobilized glucose oxidase could retain bioactivity and catalyze the reduction of dissolved oxygen. Due to the synergy between the CdTe QDs and CNTs, this novel biosensing platform based on QDs/CNTs electrode responded even more sensitively than that based on GC electrode modified by CdTe QDs or CNTs alone. The inexpensive, reliable and sensitive sensing platform based on QDs/CNTs electrode provides wide potential applications in clinical, environmental, and food analysis.     

Glucose oxidase enzyme immobilized porous silica for improved performance of a glucose biosensor

High activity of glucose oxidase (GOD) enzyme (immobilized in porous silica particles) is desirable for a better glucose biosensor. In this work, effect of pore diameter of two porous hosts on enzyme immobilization, activity and glucose sensing was compared. The hosts were amine functionalized: (i) microporous silica (NH₂-MS) and (ii) mesoporous silica (NH₂-SBA-15). Based on whether the dimension of GOD is either larger or smaller than the pore diameter, GOD was immobilized on either external or internal surface of NH₂-MS and NH₂-SBA-15, with loadings of 512.5 and 634 mg/g, respectively. However, GOD in NH₂-SBA-15 gave a higher normalized absolute activity (NAA), which led to an amperometric sensor with a larger linear range of 0.4–13.0 mM glucose. In comparison, GOD in NH₂-MS had a lower NAA and a smaller linear range of 0.4–3.1 mM. In fact, the present GOD-NH₂-SBA-15 electrode based sensor was better than other MS and SBA-15 based electrodes reported in literature. Thus, achieving only a high GOD loading (as in NH₂-MS) does not necessarily give a good sensor performance. Instead, a host with a relatively larger pore than enzyme, together with optimized electrode composition ensures the sensor to be functional in both hyper- and hypoglycemic range.     

Development of a disposable glucose biosensor using electroless-plated Au/Ni/copper low electrical resistance electrodes

This paper presents a glucose biosensor, which was developed using a Au/Ni/copper electrode. Until now, research regarding the low electrical resistance and uniformity of this biosensor electrode has not been conducted. Glucose oxidase (GOD) immobilized on the electrode effectively plays the role of an electron shuttle, and allows glucose to be detected at 0.055 V with a dramatically reduced resistance to easily oxidizable constituents. The Au/Ni/copper electrode has a low electrical resistance, which is less than 0.01 Ω, and it may be possible to mass produce the biosensor electrode with a uniform electrical resistance. The low electrical resistance has the advantage in that the redox peak occurs at a low applied potential. Using a low operating potential (0.055 V), the GOD/Au/Ni/copper structure creates a good sensitivity to detect glucose, and efficiently excludes interferences from common coexisting substances. The GOD/Au/Ni/copper sensor exhibits a relatively short response time (about 3 s), and a sensitivity of 0.85 μA mM⁻¹ with a linear range of buffer to 33 mM of glucose. The sensor has excellent reproducibility with a correlation coefficient of 0.9989 (n = 100 times) and a total non-linearity error of 3.17%.     

Direct electrochemistry of glucose oxidase and biosensing for glucose based on boron-doped carbon nanotubes modified electrode

Due to their unique physicochemical properties, doped carbon nanotubes are now extremely attractive and important nanomaterials in bioanalytical applications. In this work, selecting glucose oxidase (GOD) as a model enzyme, we investigated the direct electrochemistry of GOD based on the B-doped carbon nanotubes/glassy carbon (BCNTs/GC) electrode with cyclic voltammetry. A pair of well-defined, quasi-reversible redox peaks of the immobilized GOD was observed at the BCNTs based enzyme electrode in 0.1M phosphate buffer solution (pH 6.98) by direct electron transfer between the protein and the electrode. As a new platform in glucose analysis, the new glucose biosensor based on the BCNTs/GC electrode has a sensitivity of 111.57 microA mM(-1)cm(-2), a linear range from 0.05 to 0.3mM and a detection limit of 0.01mM (S/N=3). Furthermore, the BCNTs modified electrode exhibits good stability and excellent anti-interferent ability to the commonly co-existed uric acid and ascorbic acid. These indicate that boron-doped carbon nanotubes are the good candidate material for the direct electrochemistry of the redox-active enzyme and the construction of the related enzyme biosensors.     

A novel non-enzymatic ECL sensor for glucose using palladium nanoparticles supported on functional carbon nanotubes

A novel non-enzymatic electrochemiluminescence (ECL) sensor based on palladium nanoparticles (PdNPs)–functional carbon nanotubes (FCNTs) was discovered for glucose detection. PdNPs were homogeneously modified on FCNTs using a facile spontaneous redox reaction method. Their morphologies were characterized by transmission electron microscopy (TEM). Based on ECL experimental results, the PdNPs–FCNTs–Nafion film modified electrode displayed high electrocatalytic activity towards the oxidation of glucose. The free radicals generated by the glucose oxidation reacted with the luminol anion (LH⁻), and enhanced the ECL signal. Under the optimized conditions, the linear response of ECL intensity to glucose concentration was valid in the range from 0.5 to 40 μmol L⁻¹ (r² = 0.9974) with a detection limit (S/N = 3) of 0.09 μmol L⁻¹. In addition, the modified electrode presented high resistance towards the poisoning of chloride ion, high selectivity and long-term stability. In order to verify the sensor reliability, it was applied to the determination of glucose in glucose injection samples. The results indicated that the proposed approach provided a highly sensitive, more facile method with good reproducibility for glucose determination, promising the development of a non-enzymatic ECL glucose sensor.     

One-step "green" preparation of graphene nanosheets and carbon nanospheres mixture by electrolyzing graphite rob and its application for glucose biosensing

The graphene nanosheets and carbon nanospheres mixture (GNS–CNS) was prepared by electrolyzing graphite rob in KNO₃ solution under constant current, which was characterized by TEM, AFM, SEM, FT-IR, XRD, XPS, TGA and UV–vis. The nano-mixture can keep stable in water for more than one month. Based on this kind of mixture material, a novel electrochemical biosensing platform for glucose determination was developed. Cyclic voltammetry of glucose oxidase (GOD) immobilized on GNS–CNS/GCE exhibited a pair of well-defined quasi-reversible redox peaks at −0.488 V (E_pa) and −0.509 V (E_pc) by direct electron transfer between the protein and the electrode. The charge-transfer coefficient (α) was 0.51, the electron transfer rate constant was 2.64 s⁻¹ and the surface coverage of HRP was 3.18 × 10⁻¹⁰ mol cm⁻². The immobilized GOD could retain its bioactivity and catalyze the reduction of dissolved oxygen. The glucose biosensor has a linear range from 0.4 to 20 mM with detection limit of 0.1 mM. Moreover, the biosensor exhibits acceptable reproducibility and storage stability. The fabricated biosensor was further used to determine glucose in human plasma sample with the recoveries from 96.83% to 105.52%. Therefore, GOD/GNS–CNS/GCE could be promisingly applied to determine blood sugar concentration in the practical clinical analysis.     

Disposable, enzymatically modified printed film carbon electrodes for use in the high-performance liquid chromatographic–electrochemical detection of glucose or hydrogen peroxide from immobilized enzyme reactors

Disposable screen-printed, film carbon electrodes (PFCE) were modified with cast-coated Osmium–polyvinylpyrridine-wired horse radish peroxidase gel polymer (Os-gel-HRP) to enable the detection of the reduction at 0 mV of hydrogen peroxide (H₂O₂) derived from a post-column immobilized enzyme reactor (IMER) containing acetylcholinesterase and choline oxidase. In another series of experiments PFCE were initially modified with cast-coated Os-gel-HRP and then treated with glucose oxidase in bovine serum albumin (BSA) and cross-linked with glutaraldehyde to form a bi-layer glucose–Os-gel-HRP PFCE. This bi-layer glucose–Os-gel-HRP PFCE generated a reduction current at 0 mV to H₂O₂ derived from the reaction of glucose oxidase and glucose in solution. These enzyme-modified PFCE were housed in a radial flow cell and coupled with cation-exchange liquid chromatographic methods to temporally separate substrates in solution for the determination of acetylcholine (ACh) and choline (Ch) in the first experimental series, or glucose in the second experimental series. These two disposable enzyme-modified PFCE exhibited linear current vs. substrate relations, were durable, being usable for approximately 40 determinations, and were sufficiently sensitive to be employed in biological sampling. Both assays utilized the same HPLC equipment. The limit of detection for ACh was 16 fmol/10 μl and that for glucose was 12 μmol/7.5 μl. ACh and Ch were measured from a microdialysate from the frontal cortex of a rat. Glucose in human urine was determined using the bi-layer glucose oxidase–Os-gel-HRP PFCE.     

Fabrication of bienzyme nanobiocomposite electrode using functionalized carbon nanotubes for biosensing applications

Mediated biosensors consisting of an oxidase and peroxidase (POx) have attracted increasing attention because of their wider applicability. This work presents a novel approach to fabricate nanobiocomposite bienzymatic biosensor based on functionalized multiwalled carbon nanotubes (MWNTs) with the aim of evaluating their ability as sensing elements in amperometric transducers. Electrochemical behavior of the bienzymatic nanobiocomposite biosensor is investigated by Faradaic impedance spectroscopy and cyclic voltammetry. The results indicate that glucose oxidase (GOD) and horseradish peroxidase (HRP) are strongly adsorbed on the surface of the thionin (TH) functionalized MWNTs and demonstrate a facile electron transfer between immobilized GOD/HRP and the electrode via the functionalized MWNTs in a Nafion film. The functionalized carbon nanotubes act as molecular wires to allow efficient electron transfer between the underlying electrode and the redox centres of enzymes through TH. Linear ranges for these electrodes are from 10 nM to 10 mM for glucose and 17 nM to 56 mM for hydrogen peroxide with the detection limit of 3 and 6 nM, respectively. A remarkable feature of the bienzyme electrode is the possibility to determine glucose and hydrogen peroxide at a very low applied potential where the noise level and interferences from other electroactive compounds are minimal. Performance of the biosensor is evaluated with respect to response time, detection limit, selectivity, temperature and pH as well as operating and storage stability.     

A mediator-free glucose biosensor based on glucose oxidase/chitosan/α-zirconium phosphate ternary biocomposite

A novel glucose oxidase/chitosan/α-zirconium phosphate (GOD/chitosan/α-ZrP) ternary biocomposite was prepared by co-intercalating glucose oxidase (GOD) and chitosan into the interlayers of α-zirconium phosphate (α-ZrP) via a delamination–reassembly procedure. The results of X-ray diffraction, infrared spectroscopy, circular dichroism, and ultraviolet spectrum characterizations indicated not only the layered and hybrid structure of the GOD/chitosan/α-ZrP ternary biocomposite but also the recovered activity of the intercalated GOD improved by the co-intercalated chitosan. By depositing the GOD/chitosan/α-ZrP biocomposite film onto a glassy carbon electrode, the direct electrochemistry of the intercalated GOD was achieved with a fast electron transfer rate constant, k_s, of 7.48 ± 3.52 s⁻¹. Moreover, this GOD/chitosan/α-ZrP biocomposite modified electrode exhibited a sensitive response to glucose in the linear range of 0.25–8.0 mM (R = 0.9994, n = 14), with a determination limit of 0.076 mM.     

Multifunctional carbon nanotubes for direct electrochemistry of glucose oxidase and glucose bioassay

Polydopamine (Pdop) has recently been shown to adsorb to a wide variety of surfaces and serves as an adhesion layer to immobilize biological molecules. In this work, the multifunctional carbon nanotube (CNT) composites were prepared though the oxidation of dopamine at room temperature and subsequent electroless silver deposition by mildly stirring. The stable immobilization and direct electron transfer of glucose oxidase were achieved on the composite film modified glassy carbon electrode. The resulting electrode gave a well-defined redox peaks with a formal potential of about −482 mV (vs. SCE) in pH 7.0 buffer. The electron transfer rate constant was estimated to be 3.6 s⁻¹, due to the combined contribution of Pdop, CNTs and Ag nanoparticles with the help of Nafion. Furthermore, the method for detecting of glucose was proposed based on the decrease of oxygen caused by the enzyme-catalyzed reaction between glucose oxidase (GOD) and glucose. The linear response to glucose ranging from 50.0 μM to 1.1 mM (R² = 0.9958), with a calculated detection limit of 17.0 μM at a signal-to-noise ratio of 3. The low calculated apparent Michaelis–Menten constant was 5.46 mM, implying the high enzymatic activity and affinity of immobilized GOD for glucose. It can reasonably be expected that this observation might hold true for other noble metal nanostructure-electroactive protein systems, providing a promising platform for the development of biosensors and biofuel cells.     

Amperometric glucose biosensor based on adsorption of glucose oxidase at platinum nanoparticle-modified carbon nanotube electrode

A new amperometric biosensor, based on adsorption of glucose oxidase (GOD) at the platinum nanoparticle-modified carbon nanotube (CNT) electrode, is presented in this article. CNTs were grown directly on the graphite substrate. The resulting GOD/Pt/CNT electrode was covered by a thin layer of Nafion to avoid the loss of GOD in determination and to improve the anti-interferent ability. The morphologies and electrochemical performance of the CNT, Pt/CNT, and Nafion/GOD/Pt/CNT electrodes have been investigated by scanning electron microscopy, cyclic voltammetry, and amperometric methods. The excellent electrocatalytic activity and special three-dimensional structure of the enzyme electrode result in good characteristics such as a large determination range (0.1-13.5mM), a short response time (within 5s), a large current density (1.176 mA cm(-2)), and high sensitivity (91mA M(-1)cm(-2)) and stability (73.5% remains after 22 days). In addition, effects of pH value, applied potential, electrode construction, and electroactive interferents on the amperometric response of the sensor were investigated and discussed. The reproducibility and applicability to whole blood analysis of the enzyme electrode were also evaluated.     

High-performance bioanode based on the composite of CNTs-immobilized mediator and silk film-immobilized glucose oxidase for glucose/O2 biofuel cells

A high-performance bioanode based on the composite of carbon nanotubes (CNTs)-immobilized mediator and silk film (SF)-immobilized glucose oxidase (GOD) was developed for glucose/O(2) biofuel cell (BFC). Ferrocenecarboxaldehyde (Fc) was used as the mediator and covalently immobilized on the ethylenediamine (EDA)-functionalized CNTs (CNTs-EDA). GOD was cross-linked on the SF with glutaraldehyde (GA) as the cross-linking agent. The resulting electrode (CNTs-Fc/SF-GOD/glassy carbon (GC) electrode) exhibited good catalytic activity towards glucose oxidation and excellent stability. For the assembled glucose/O(2) BFC with the CNTs-Fc/SF-GOD/GC electrode as the bioanode and a commercial E-TEK Pt/C modified GC electrode as the cathode, the open circuit potential is 0.48 V and the maximum power density of 50.70 μW cm(-2) can be achieved at 0.15 V.     

Nonenzymatic glucose sensor based on ultrasonic-electrodeposition of bimetallic PtM (M = Ru, Pd and Au) nanoparticles on carbon nanotubes–ionic liquid composite film

We report here for the first time on the fabrication of highly dispersed PtM (M = Ru, Pd and Au) nanoparticles on composite film of multi-walled carbon nanotubes (MWNTs)–ionic liquid (IL, i.e., trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide) by using ultrasonic-electrodeposition method. The PtM nanoparticles are characterized by scanning electron microscopy, X-ray photoelectron spectroscopy and X-ray diffraction, and we find that they are well-dispersed and exhibit alloy properties. Electrochemical experiments show that the PtRu(1:1, i.e., ratio of c(H₂PtCl₆)/c(RuCl₃))–MWNT–IL nanocomposite modified glassy carbon electrode (PtRu(1:1)–MWNT–IL/GCE) has smaller electron transfer resistance and larger active surface area than PtRu(1:1)/GCE, PtRu(1:1)–MWNT/GCE, PtPd(1:1)–MWNT–IL/GCE and PtAu(1:1)–MWNT–IL/GCE. The PtRu(1:1)–MWNT–IL/GCE also presents stronger electrocatalytic activity toward the glucose oxidation than other electrodes. At −0.1 V, the electrode responds linearly to glucose up to 15 mM in neutral media, with a detection limit of 0.05 mM (S/N = 3) and detection sensitivity of 10.7 μA cm⁻² mM⁻¹. Meanwhile, the interference of ascorbic acid, uric acid, acetamidophenol and fructose is effectively avoided. The as-made sensor was applied to the determination of glucose in serum and urine samples. The results agreed closely with the results obtained by a hospital. This novel nonenzyme sensor thus has potential application in glucose detection.     

A biosensor based on the self-entrapment of glucose oxidase within biomimetic silica nanoparticles induced by a fusion enzyme

We constructed a fusion protein (GOx-R5) consisting of R5 (a polypeptide component of silaffin) and glucose oxidase (GOx) that was expressed in Pichia pastoris. Silaffin proteins are responsible for the formation of a silica-based cell matrix of diatoms, and synthetic variants of the R5 protein can perform silicification in vitro[1]. GOx secreted by P. pastoris was self-immobilized (biosilicification) in a pH 5 citric buffer using 0.1 M tetramethoxysilane as a silica source. This self-entrapment property of GOx-R5 was used to immobilize GOx on a graphite rod electrode. An electric cell designed as a biosensor was prepared to monitor the glucose concentrations. The electric cell consisted of an Ag/AgCl reference electrode, a platinum counter electrode, and a working electrode modified with poly(neutral red) (PNR)/GOx/Nafion. Glucose oxidase was immobilized by fused protein on poly(neutral red) and covered by Nafion to protect diffusion to the solution. The morphology of the resulting composite PNR/GOx/Nafion material was analyzed by scanning electron microscopy (SEM). This amperometric transducer was characterized electrochemically using cyclic voltammetry and amperometry in the presence of glucose. An image produced by scanning electron microscopy supported the formation of a PNR/GOx complex and the current was increased to 1.58 μA cm⁻¹ by adding 1 mM glucose at an applied potential of −0.5 V. The current was detected by way of PNR-reduced hydrogen peroxide, a product of the glucose oxidation by GOx. The detection limit was 0.67 mM (S/N = 3). The biosensor containing the graphite rod/PNR/GOx/Nafion detected glucose at various concentrations in mixed samples, which contained interfering molecules. In this study, we report the first expression of R5 fused to glucose oxidase in eukaryotic cells and demonstrate an application of self-entrapped GOx to a glucose biosensor.     

Amperometric sensor based on ferrocene-modified multiwalled carbon nanotube nanocomposites as electron mediator for the determination of glucose

A kind of nanocomposite with good dispersion in water was prepared through covalent adsorption of ferrocenecarboxaldehyde on multiwalled carbon nanotubes (MWNTs) for electrical communication between glucose oxidase (GOD) and electrode. The ferrocene-modified multiwalled carbon nanotube nanocomposites (MWNTs-Fc) could be conveniently cast on electrode surfaces. With the aid of chitosan, GOD was then immobilized on the nanostructure film to form a reagentless amperometric sensor for glucose determination. FTIR spectra and cyclic voltammetry were used to characterize the nanocomposites. The presence of both ferrocene as mediator of electron transfer and MWNTs as conductor enhanced greatly the enzymatic response to the oxidation of glucose. The novel biosensor exhibited a fast response toward glucose with a detection limit of 3.0 × 10⁻⁶ mol/L and the linear range extended up to 3.8 × 10⁻³ mol/L.     

Role of the support surface on the loading and the activity of Pseudomonas fluorescens lipase used for biodiesel synthesis

The present work investigates the influence of the support surface on the loading and the enzymatic activity of the immobilized Pseudomonas fluorescens lipase. Different porous materials, polypropylene (Accurel), polymethacrylate (Sepabeads EC-EP), silica (SBA-15 and surface modified SBA-15), and an organosilicate (MSE), were used as supports. The immobilized biocatalysts were compared towards sunflower oil ethanolysis for the sustainable production of biodiesel. Since the supports have very different structural (ordered hexagonal and disordered) and textural features (surface area, pore size, and total pore volume), in order to consider only the effect of the support surface, experiments were performed at low surface coverage. The different functional groups occurring on the support surface allowed either physical (Accurel, MSE, and SBA-15) or chemical adsorption (Sepabeads EC-EP and SBA-15–R-CHO). The surface-modified SBA-15 (SBA-15–R-CHO) allowed the highest loading. The lipase immobilized on the MSE was the most active biocatalyst. However, in terms of catalytic efficiency (activity/loading) the lipase immobilized on the SBA-15, the support that allowed the lowest loading, was the most efficient.     

A novel glucose biosensor based on the immobilization of glucose oxidase onto gold nanoparticles-modified Pb nanowires

A novel glucose biosensor was developed, based on the immobilization of glucose oxidase (GOD) with cross-linking in the matrix of bovine serum albumin (BSA) on a Pt electrode, which was modified with gold nanoparticles decorated Pb nanowires (GNPs-Pb NWs). Pb nanowires (Pb NWs) were synthesized by an l-cysteine-assisted self-assembly route, and then gold nanoparticles (GNPs) were attached onto the nanowire surface through –SH–Au specific interaction. The morphological characterization of GNPs-Pb NWs was examined by transmission electron microscopy (TEM). Cyclic voltammetry and chronoamperometry were used to study and to optimize the electrochemical performance of the resulting biosensor. The synergistic effect of Pb NWs and GNPs made the biosensor exhibit excellent electrocatalytic activity and good response performance to glucose. The effects of pH and applied potential on the amperometric response of the biosensor have been systemically studied. In pH 7.0, the biosensor showed the sensitivity of 135.5 μA mM⁻¹ cm⁻², the detection limit of 2 μM (S/N = 3), and the response time <5 s with a linear range of 5–2200 μM. Furthermore, the biosensor exhibits good reproducibility, long-term stability and relative good anti-interference.     

Amperometric glucose biosensor based on multilayer films via layer-by-layer self-assembly of multi-wall carbon nanotubes, gold nanoparticles and glucose oxidase on the Pt electrode

A novel amperometric glucose biosensor based on the nine layers of multilayer films composed of multi-wall carbon nanotubes (MWCNTs), gold nanoparticles (GNp) and glucose oxidase (GOD) was developed for the specific detection of glucose. MWCNTs were chemically modified with the H₂SO₄–HNO₃ pretreatment to introduce carboxyl groups which were used to interact with the amino groups of poly(allylamine) (PAA) and cysteamine via 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide/N-hydroxysuccinimide cross-linking reaction, respectively. A cleaned Pt electrode was immersed in PAA, MWCNTs, cysteamine and GNp, respectively, followed by the adsorption of GOD, assembling the one layer of multilayer films on the surface of Pt electrode (GOD/GNp/MWCNTs/Pt electrode). Repeating the above process could assemble different layers of multilayer films on the Pt electrode. PBS washing was applied at the end of each assembly deposition for dissociating the weak adsorption. Film assembling and characterization were studied by transmission electron microscopy and quartz crystal microbalance, and properties of the resulting glucose biosensors were measured by electrochemical measurements. The marked electrocatalytic activity of Pt electrode based on multilayer films toward H₂O₂ produced during GOD enzymatic reactions with glucose permitted effective low-potential amperometric measurement of glucose. Taking the sensitivity and selectivity into consideration, the applied potential of 0.35 V versus Ag/AgCl was chosen for the oxidation detection of H₂O₂ in this work. Among the resulting glucose biosensors, the biosensor based on nine layers of multilayer films was best. It showed a wide linear range of 0.1–10 mM glucose, with a remarkable sensitivity of 2.527 μA/mM, a detection limit of 6.7 μM estimated at a signal-to-noise ratio of 3 and fast response time (within 7 s). Moreover, it exhibited good reproducibility, long-term stability and the negligible interferences of ascorbic acid, uric acid and acetaminophen. The study can provide a feasible approach on developing new kinds of oxidase-based amperometric biosensors, and can be used as an illustration for constructing various hybrid structures.     

Fabrication of polymeric ionic liquid/graphene nanocomposite for glucose oxidase immobilization and direct electrochemistry

A novel polymeric ionic liquid functionalized graphene, poly(1-vinyl-3-butylimidazolium bromide)-graphene (denoted as poly(ViBuIm(+)Br(-))-G), was synthesized. FTIR, UV-vis spectra and TEM were used to characterize the formation of as synthesized nanocomposites. Due to the modification of the polymeric ionic liquid, poly(ViBuIm(+)Br(-))-G can not only be dispersed well in aqueous solutions to form a homogeneous colloidal suspension of individual nanosheets, but also exhibit a strong positive charge. Based on self-assembly, the negatively charged glucose oxidase (GOD) was immobilized onto the poly(ViBuIm(+)Br(-))-G to form a GOD/poly(ViBuIm(+)Br(-))-G/glassy carbon (GC) electrode under mild conditions. With the advantage of both poly(ViBuIm(+)Br(-)) and graphene, poly(ViBuIm(+)Br(-))-G can provide a favorable and conductive microenvironment for the immobilized GOD and thus promote their direct electron transfer at the GC electrode. Furthermore, the GOD/poly(ViBuIm(+)Br(-))-G/GC electrode displayed an excellent sensitivity, together with a wide linear range and excellent stability for the detection of glucose. Accordingly, these unique properties of such novel nanocomposite generate a promising platform for the construction of mediator-free enzymatic biosensors.     

Glucose biosensor based on nano-SiO2 and “unprotected” Pt nanoclusters

The “unprotected” Pt nanoclusters (average size 2 nm) mixed with the nanoscale SiO₂ particles (average size 13 nm) were used as a glucose oxidase immobilization carrier to fabricate the amperometric glucose biosensor. The bioactivity of glucose oxidase (GOx) immobilized on the composite was maintained and the as-prepared biosensor demonstrated high sensitivity (3.85 μA mM⁻¹) and good stability in glucose solution. The Pt–SiO₂ biosensor showed a detection limit of 1.5 μM with a linear range from 0.27 to 4.08 mM. In addition, the biosensor can be operated under wide pH range (pH 4.9–7.5) without great changes in its sensitivity. Cyclic voltammetry measurements showed a mixed controlled electrode reaction.