Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+,Dy3+ co‐doped Ba2MgSi2O7 phosphors

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu²⁺‐doped and Eu²⁺,Dy³⁺‐co‐doped Ba₂MgSi₂O₇ (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid‐state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscopy (TEM) and energy‐dispersive X‐ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba₂MgSi₂O₇:Eu²⁺ showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba₂MgSi₂O₇:Eu²⁺Dy³⁺ showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f⁶ 5d¹ to 4f⁷ transition of Eu²⁺. TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu²⁺ doping in Ba₂MgSi₂O₇ phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy³⁺ ions were co‐doped in Ba₂MgSi₂O₇:Eu²⁺ and maximum TL intensity was observed for 2 mol% of Dy³⁺. TL emission spectra of Ba_1.95MgSi₂O₇:0.05Eu²⁺ and Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co‐doping. The trap depths were calculated to be 0.54 eV for Ba_1.95MgSi₂O₇:0.05Eu²⁺ and 0.54 eV and 0.75 eV for Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors. It was observed that co‐doping with small amounts of Dy³⁺ enhanced the thermoluminescence properties of Ba₂MgSi₂O₇ phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The following parts of the abstract have been edited for consistency. '4f65d1' has been corrected to '4f⁶ 5d¹', '4f7' has been corrected to '4f⁷', 'Ba1.95' has been corrected to 'Ba_1.95' and 'Ba1.93' has been corrected to 'Ba_1.93' respectively.]     

Luminescence in Ba2Sr2Al2O7:RE (RE = Tb3+,Eu3+ and Dy3+) novel aluminate phosphors

The luminescence of novel rare earth ( Tb ^{3 +} , Eu ^{3 +} and Dy ^{3 +} )‐activated Ba ₂ Sr ₂ Al ₂ O ₇ phosphors for solid‐state lighting is presented. The aluminate phosphors were synthesized using a one‐step combustion method. X‐Ray diffraction, scanning electron microscopy and photoluminescence characterizations were performed to understand the mechanism of excitation and the corresponding emission in the as‐prepared phosphor, as characterized the phase purity and microstructure. Improvements in the luminescence properties of the phosphors with rare earth concentration were observed. The phosphor hue could be tuned from blue, green and red by proper selection of rare earth ions in typical concentrations. Effective absorption in the near‐ultraviolet region was observed, which makes the phosphor a potential candidate for ultraviolet light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

Intense green‐, red‐emitting Tb3+, Tb3+/Bi3+‐doped and Sm3+, Sm3+/La3+‐doped Ca2Al2SiO7 phosphors

This paper focuses on an optical study of a Tb³⁺/Bi³⁺‐doped and Sm³⁺/La³⁺‐ doped Ca₂Al₂SiO₇ phosphor synthesized using combustion methods. Here, Ca₂Al₂SiO₇:Sm³⁺ showed a red emission band under visible light excitation but, when it co‐doped with La³⁺ ions, the emission intensity was further enhanced. Ca₂Al₂SiO₇:Tb³⁺ shows the characteristic green emission band under near‐ultraviolet light excitation wavelengths, co‐doping with Bi³⁺ ions produced enhanced photoluminescence intensity with better colour tunable properties. The phosphor exhibited better phase purity and crystallinity, confirmed by X‐ray diffraction. Binding energies of Ca(2p), Al(2p), Si(2p), O(1s) were studied using X‐ray photoelectron spectroscopy. The reported phosphor may be a promising visible light excited red phosphor for light‐emitting diodes and energy conversion devices.     

Synthesis and luminescence characterization of Y2BaZnO5:RE (RE = Eu3+, Tb3+, Pr3+ and Sm3+) phosphors

Modified synthesis and luminescence of Y₂BaZnO₅ phosphors activated with the rare earths (RE) Eu³⁺, Tb³⁺, Pr³⁺ and Sm³⁺ are reported. RE₂BaZnO₅ phosphors have attracted attention because of their interesting magnetic and optical properties; and are usually prepared using a two‐step solid‐state reaction. In the first step, carbonates or similar precursors are thoroughly mixed and heated at 900°C to decompose them to oxides. To eliminate the unwanted phases like BaRE₂O₄, the resulting powders are reheated at 1100°C for a long time. We prepared Y₂BaZnO₅ phosphors activated with various activators by replacing the first step with combustion synthesis. The photoluminescence results are presented. The photoluminescence results for Eu³⁺, Tb³⁺ and Pr³⁺ are in good agreement with the literature. However, photoluminescence emission from Sm³⁺ has not been documented previously. The excitation spectrum of Eu³⁺ is dominated by a charge transfer band around 261 nm, and an additional band around 238 nm is always present, irrespective of the type of activator. The presence of this band for all these different types of activators was interpreted as host absorption.     

Structural and luminescence properties of Y2‐xGeMoO8:REx (RE = Eu,Tb) phosphors

Y_2‐xGeMoO₈:RE_x (RE = Eu, Tb) phosphors were synthesized using a facile sol–gel method. The morphology and structure of the phosphors were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X‐ray diffraction (XRD); while their luminescent properties were investigated by photoluminescence (PL) spectrometry. Our results reveal that all of these Y_2‐xGeMoO₈:RE_x (RE = Eu, Tb) phosphors adopted the tetragonal phase, belonging to Scheelite (CaWO₄) structure. The obtained YGeMoO₈:Eu phosphors exhibit a strong emission in the red light range which can be assigned to the ⁵D₀ → ⁷F₂ transition of Eu³⁺ when it is excited at 459 nm. Under 392 and 489 nm excitation, the YGeMoO₈:Tb phosphors present predominant green emission (⁵D₄ → ⁷F₅) at 540 nm. The highest emission of the phosphors can be achieved by adjusting the doping concentration to be 0.25 for Eu³⁺ and 0.15 for Tb³⁺, respectively. The promising luminescence properties of these materials indicate that they can be potentially applied to white‐light‐emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.     

Luminescent properties and energy transfer in the green phosphors LaBSiO5:Tb3+,Ce3+

LaBSiO₅ phosphors doped with Ce³⁺ and Tb³⁺ were synthesized using the conventional solid‐state method at 1100 °C. The phase purity and luminescent properties of these phosphors are investigated. LaBSiO₅:Tb³⁺ phosphors show intense green emission, and LaBSiO₅ phosphors doped with Ce³⁺ show blue–violet emission under UV light excitation. LaBSiO₅ phosphors co‐doped with Ce³⁺ and Tb³⁺ exhibit blue–violet and green emission under excitation by UV light. The blue–violet emission is due to the 5d–4f transition of Ce³⁺ and the green emission is ascribed to the ⁵D₄ → ⁷ F₅ transition of Tb³⁺. The spectral overlap between the excitation band of Tb³⁺ and the emission band of Ce³⁺ supports the occurrence of energy transfer from Ce³⁺ to Tb³⁺, and the energy transfer process was investigated. Copyright © 2014 John Wiley & Sons, Ltd.     

Photoluminescence properties and energy transfer in Ce3+/Dy3+ co‐doped Sr3MgSi2O8 phosphors for potential application in ultraviolet white light‐emitting diodes

Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors were prepared by a solid‐state reaction technique and the photoluminescence properties were investigated. The emission spectra show not only a band due to Ce³⁺ ions (403 nm) but also as a band due to Dy³⁺ ions (480, 575 nm) (UV light excitation). The photoluminescence properties reveal that effective energy transfer occurs in Ce³⁺/Dy³⁺ co‐doped Sr₃MgSi₂O₈ phosphors, and the co‐doping of Ce³⁺ could enhance the emission intensity of Dy³⁺ to a certain extent by transferring its energy to Dy³⁺. The Ce³⁺/Dy³⁺ energy transfer was investigated by emission/excitation spectra, and photoluminescence decay behaviors. In Sr_2.94MgSi₂O₈:0.01Ce³⁺, 0.05Dy³⁺ phosphors, the fluorescence lifetime of Dy³⁺ (from 3.35 to 27.59 ns) is increased whereas that of Ce³⁺ is greatly decreased (from 43.59 to 13.55 ns), and this provides indirect evidence of the Ce³⁺ to Dy³⁺ energy transfer. The varied emitted color of Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ phosphors from blue to white were achieved by altering the concentration ratio of Ce³⁺ and Dy³⁺. These results indicate Sr₃MgSi₂O₈:Ce³⁺, Dy³⁺ may be as a candidate phosphor for white light‐emitting diodes. Copyright © 2012 John Wiley & Sons, Ltd.     

Improving green emission of Tb3+ ions in BaO‐B2O3‐P2O5 glasses by means of Al3+ ions

BaO‐B₂O₃‐P₂O₅ glasses doped with a fixed concentration of Tb³⁺ ions and varying concentrations of Al₂O₃ were synthesized, and the influence of the Al³⁺ ion concentration on the luminescence efficiency of the green emission of Tb³⁺ ions was investigated. The optical absorption, excitation, luminescence spectra and fluorescence decay curves of these glasses were recorded at ambient temperature. The emission spectra of terbium ions when excited at 393 nm exhibited two main groups of bands, corresponding to ⁵D₃ → ⁷F_j (blue region) and ⁵D₄ → 7F_j (green region). From these spectra, the radiative parameters, viz., spontaneous emission probability A, total emission probability A_T, radiative lifetime τ and fluorescent branching ratio β, of different transitions originating from the ⁵D₄ level of Tb³⁺ ions were evaluated based on the Judd‐Ofelt theory. A clear increase in the quantum efficiency and luminescence of the green emission of Tb³⁺ ions corresponding to ⁵D₄ → ⁷F₅ transition is observed with increases in the concentration of Al₂O₃ up to 3.0 mol%. The improvement in emission is attributed to the de‐clustering of terbium ions by Al³⁺ ions and also to the possible admixing of wave functions of opposite parities. Copyright © 2016 John Wiley & Sons, Ltd.     

Photoluminescence,cathodoluminescence and thermal stability of Sm3+‐activated Sr3La(VO4)3 red‐emitting phosphors

A series of Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors were synthesized by a facile sol‐gel method. X‐ray diffraction patterns and photoluminescence (PL)/cathodoluminescence (CL) spectra as well as PL decay curves were employed to characterize the obtained samples. Upon 402 nm light excitation, the characteristic emissions of Sm³⁺ ions corresponding to ⁴G_5/2→⁶H_J transitions were observed in all the as‐prepared products. The PL emission intensity was increased with increase in Sm³⁺ ion concentration, while concentration quenching occurred when the doping concentration was over 4 mol%. The non‐radiative energy transfer mechanism for concentration quenching of Sm³⁺ ions was dominated by dipole–dipole interaction and the critical distance was around 21.59 Å. Furthermore, temperature‐dependent PL emission spectra revealed that the obtained phosphors possessed good thermal stability with an activation energy of 0.19 eV. In addition, the CL spectra of the samples were almost the same as the PL spectra, and the CL emission intensity showed a tendency to increase with increase in accelerating voltage and filament current. These results suggest that the Sm³⁺‐activated Sr₃La(VO₄)₃ phosphors with good color coordinates, high color purity and superior thermal stability may be a potential candidate for applications in white light‐emitting diodes and field‐emission displays as red‐emitting phosphors.     

Structural characterization and optical properties of Ca2MgSi2O7:Eu2+,Dy3+ phosphor by solid‐state reaction method

Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was prepared by the solid‐state reaction method under a weak reducing atmosphere. The obtained phosphor was characterized using X‐ray diffraction (XRD), transmission electron microscopy (TEM), field emission scanning electron microscopy (FESEM), energy dispersive X‐ray spectroscopy (EDX) and Fourier transform infrared (FT‐IR) techniques. The phase structure of the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor was akermanite type, which is a member of the melilite group. The surface morphology of the sintered phosphor was not uniform and phosphors aggregated tightly. EDX and FT‐IR spectra confirm the elements present in the Ca₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphor. Under UV excitation, a broadband emission spectrum was found. The emission spectra observed in the green region centered at 535 nm, which is due to the 4f–5d transition. The mechanoluminescence (ML) intensity of the prepared phosphor increased linearly with increases in the mechanical load. The ML spectra were similar to the photoluminescence (PL), which indicates that ML is emitted from the same emitting center of Eu²⁺ ions as PL. Copyright © 2014 John Wiley & Sons, Ltd.     

Luminescence and energy‐transfer properties of color‐tunable Ca2Mg0.25Al1.5Si1.25O7:Ce3+/Eu2+/Tb3+ phosphors for ultraviolet light‐emitting diodes

A series of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺/Eu²⁺/Tb³⁺ phosphors was been prepared via a conventional high temperature solid‐state reaction and their luminescence properties were studied. The emission spectra of Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺ and Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Tb³⁺ phosphors show not only a band due to Ce³⁺ ions (409 nm) but also as a band due to Eu²⁺ (520 nm) and Tb³⁺ (542 nm) ions. More importantly, the effective energy transfer from Ce³⁺ to Eu²⁺ and Tb³⁺ ions was confirmed and investigated by emission/excitation spectra and luminescent decay behaviors. Furthermore, the energy level scheme and energy transfer mechanism were investigated and were demonstrated to be of resonant type via dipole–dipole (Ce³⁺ to Eu²⁺) and dipole–quadrupole (Ce³⁺ to Tb³⁺) reactions, respectively. Under excitation at 350 nm, the emitting color could be changed from blue to green by adjusting the relative doping concentration of Ce³⁺ and Eu²⁺ ions as well as Ce³⁺ and Tb³⁺ ions. The above results indicate that Ca₂Mg_0.25Al_1.5Si_1.25O₇:Ce³⁺,Eu²⁺/Tb³⁺ are promising single‐phase blue‐to‐green phosphors for application in phosphor conversion white‐light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Eu3+–Eu2+‐doped xAl2O3–ySiO2 and xAl2O3–zMgO composites phosphors

In this paper, the Eu³⁺–Eu²⁺ (4%, molar ratio)‐doped xAl₂O₃–ySiO₂ (x = 0–2.5, y = 1–5) and xAl₂O₃–zMgO (x = 0–1.5, z = 0–3) composites phosphors with different Al₂O₃ to SiO₂ (A/S) and Al₂O₃ to MgO (A/M) ratios were prepared using a high‐temperature solid‐state reaction under air atmosphere. The effects of the A/S and A/M on luminescence properties, crystal structure, electron spin resonance, and Commission Internationale de l’Eclairage chromaticity coordinates of the samples were systematically analyzed. These results indicated that the different A/S and A/M ratios in the matrix effectively affected the crystal phase, degrees of self‐reduction of Eu³⁺, and led the relative emission intensity of Eu²⁺/Eu³⁺ to change and adjust.     

Persistent luminescence of CaMgSi2O6:Eu2+,Dy3+ and CaMgSi2O6:Eu2+,Ce3+ phosphors prepared using the solid‐state reaction method

CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were synthesized using the solid‐state reaction method. X‐Ray diffraction (XRD) and photoluminescence (PL) analyses were used to characterize the phosphors. The XRD results revealed that the synthesized CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors were crystalline and are assigned to the monoclinic structure with a space group C2/c. The calculated crystal sizes of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors with a main (221) diffraction peak were 44.87 and 53.51 nm, respectively. Energy‐dispersive X‐ray spectroscopy (EDX) confirmed the proper preparation of the sample. The PL emission spectra of CaMgSi₂O₆:Eu²⁺,Dy³⁺ and CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphors have a broad band peak at 444.5 and 466 nm, respectively, which is due to electronic transition from 4f⁶5d¹ to 4f⁷. The afterglow results indicate that the CaMgSi₂O₆:Eu²⁺,Dy³⁺ phosphor has better persistence luminescence than the CaMgSi₂O₆:Eu²⁺,Ce³⁺ phosphor. Copyright © 2015 John Wiley & Sons, Ltd.     

Combustion synthesis and luminescence properties of SrAl2O4:Eu2+, Dy3+, Tb3+ phosphor.

Eu(2+), Dy(3+) and Tb(3+) co-doped strontium aluminate phosphor with high brightness and long afterglow was synthesized by a combustion method, using urea as a reducer. The properties of SrAl(2)O(4):Eu(2+),Dy(3+),Tb(3+) phosphor with a series of initiating combustion temperatures, urea concentrations and boric acid molar fractions were investigated. The sample at initiating combustion temperature of 600 degrees C exhibited an intense emission peak at 513 nm, in which the phosphor existed as a single-phase monoclinic structure. The experimental results showed that the optimum ratio of urea is 2.0 times higher than theoretical quantities and that the suitable molar fraction of H(3)BO(3) is 0.08. The average particle size of the phosphor was 50-80 nm and its luminescence properties were studied systematically. Compared with SrAl(2)O(4):Eu(2+),Dy(3+) phosphor, the initial luminescence brightness improved from 2.50 candela (cd)/m(2) to 3.55 cd/m(2) and the long afterglow time was prolonged from 1290 s to 2743 s.     

Luminescence properties of a novel red phosphor 6LaPO4–3La3PO7–2La7P3O18:Eu3+

Eu³⁺‐doped 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈ red luminescent phosphors were synthesized by co‐deposition and high‐temperature solid‐state methods and its polyphase state was confirmed by X‐ray diffraction analysis. Transmission electron microscopy showed the grain morphology as a mixture of rods and spheres. Luminescence properties of the phosphor were investigated and its red emission parameters were evaluated as a function of Eu³⁺ concentration (3.00–6.00 mol%). Excitation spectra of 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈:Eu³⁺ showed strong absorption bands at 280, 395, and 466 nm, while the luminescence spectra exhibited prominent red emission peak centred at 615 nm (⁵D₀→⁷F₂) in the red region. CIE chromaticity coordinates of the 6LaPO₄–3La₃PO₇–2La₇P₃O₁₈:5%Eu³⁺ phosphor were (0.668, 0.313) in the red region, and defined its potential application as a red phosphor.     

Enhancement of the luminescence properties of Sr3(PO4)2:Dy3+,Li+ white‐light‐emitting phosphors by charge compensator Li+ co‐doping

Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors were prepared using a simple high temperature solid method for luminescence enhancement. The structures of the as‐prepared samples agreed well with the standard phase of Sr₃(PO₄)₂, even when Dy³⁺ and Li⁺ were introduced. Under ultraviolet excitation at 350 nm, the Sr₃(PO₄)₂:Dy³⁺ sample exhibited two emission peaks at 483 nm and 580 nm, which were due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. A white light was fabricated using these two emissions from the Sr₃(PO₄)₂:Dy³⁺ phosphors. The luminescence properties of Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors, including emission intensity and decay time, were improved remarkably with the addition of Li⁺ as the charge compensator, which would promote their application in near‐ultraviolet excited white‐light‐emitting diodes.     

Combustion synthesis of blue‐emitting submicron CaAl4O7:Eu2+, Dy3+ persistence phosphor

Long persistence phosphor CaAl₄O₇: Eu²⁺, Dy³⁺ were prepared by a combustion method. The phosphors were characterized by means of X‐ray diffraction (XRD), scanning electron microscopy (SEM), decay time measurement techniques and photoluminescence spectra (PL). The CaAl₄O₇: Eu²⁺, Dy³⁺ phosphor showed a broad blue emission, peaking at 445 nm when excited at 341 nm. Such a blue emission can be attributed to the intrinsic 4f → 5d transitions of Eu²⁺ in the host lattices. The lifetime decay curve of the Dy³⁺ co‐doped CaAl₄O₇: Eu²⁺ phosphor contains a fast decay component and another slow decay one. Surface morphology also has been studied by SEM. The calculated CIE colour chromaticity coordinates was (0.227, 043). We have also discussed a possible long‐persistent mechanism of CaAl₄O₇:Eu²⁺, Dy³⁺ phosphor. All the results indicate that this phosphor has promising potential for practical applications in the field of long‐lasting phosphors for the purposes of sign boards and defence. Copyright © 2011 John Wiley & Sons, Ltd.     

Effect of Dy3+ or Eu2+ co‐activator on a BaCa(SO4)2:Ce3+ mixed alkaline earth sulfate phosphor

The individual emission and energy transfer between Ce³⁺ and Eu²⁺ or Dy³⁺ in BaCa(SO₄)₂ mixed alkaline earth sulfate phosphor prepared using a co‐precipitation method is described. The phosphor was characterized by X‐ray diffraction (XRD) and photoluminescence (PL) studies and doped by Ce;Eu and Dy rare earths. All phosphors showed excellent blue–orange emission on excitation with UV light. PL measurements reveal that the emission intensity of Eu²⁺ or Dy³⁺ dopants is greater than when they are co‐doped with Ce³⁺. An efficient Ce³⁺ → Eu²⁺ [²T_2g(4f⁶5d) → ⁸S_7/2(4f₇)] and Ce³⁺ → Dy³⁺ (⁴ F_9/2 → ⁶H_15/2 and ⁴ F_9/2 → ⁶H_13/2) energy transfer takes place in the BaCa(SO₄)₂ host. A strong blue emission peak was observed at 462 nm for Eu²⁺ ions and an orange emission peak at 574 nm for Dy³⁺ ions. Hence, this phosphor may be used as a lamp phosphor. Copyright © 2015 John Wiley & Sons, Ltd.     

Systematic study of photoluminescence,lyoluminescence and mechanoluminescence in Ce3+‐ and Eu3+‐activated Li3PO4 phosphors

Li₃PO₄ phosphor was prepared using a modified solid‐state diffusion technique. In this work, photoluminescence, lyoluminescence and mechanoluminescence studies were carried out in a Li₃PO₄ microcrystalline powder doped with different rare earths. In photoluminescence studies, characteristic emission of Ce and Eu was observed. The lyoluminescence glow curves of Li₃PO₄ microcrystals show that lyoluminescence intensity initially increases with time and then decreases exponentially. The decay time consists of two components for all masses. The dependence of decay time, especially the longer component, on mass has been investigated. Experiments on γ‐irradiated crystals have proved that the light emission originates from the recombination of released F‐centres with trapped holes (V₂‐centres) at the sulfuric acid–solid interface. Incorporation of bivalent alkali in solid lithium phosphate leads to an enhancement of lyoluminescence. A possible explanation for the experimental results has been attempted. The phosphor has a mechanoluminescence single glow peak. Mechanoluminescence intensity under various loading conditions was investigated. It is observed that mechanoluminescence intensity increases with increasing impurity concentration and increasing piston impact velocity. The results may be considered as only being of academic interest in solid‐state materials. Copyright © 2013 John Wiley & Sons, Ltd.     

Demystification of luminescence properties and the near imperceptible thermal quenching of Sm3+-doped tungstate phosphors

Ultra-high thermally stable Ca₂MgWO₆:xSm³⁺ (x = 0.5, 0.75, 1, 1.25, and 1.5 mol%) double perovskite phosphors were synthesized through solid-state reaction method. Product formation was confirmed by comparing the X-ray diffraction (XRD) patterns of the phosphors with the standard reference file. The structural, morphological, thermal, and optical properties of the prepared phosphor were examined in detail using XRD, Fourier transform infrared spectra, scanning electron microscopy, diffused reflectance spectra, thermogravimetric analysis (TGA), photoluminescence emission, and temperature-dependent PLE (TDPL). It was seen that the phosphor exhibited emission in the reddish region for the near-ultraviolet excitation with moderate Colour Rendering Index values and high colour purity. The optimized phosphor (x = 1.25 mol%) was found to possess a direct optical band gap of 3.31 eV. TGA studies showed the astonishing thermal stability of the optimized phosphor. Additionally, near-zero thermal quenching was seen in TDPL due to elevated phonon-assisted radiative transition. Furthermore, the anti-Stokes and Stokes emission peaks were found to be sensitive toward the temperature change and followed a Boltzmann-type distribution. All these marked properties will make the prepared phosphors a suitable candidate for multifield applications and a fascinating material for further development.