Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

The luminescent properties and crystal structure of Sr(1.5‐x)‐(1.5y)Mg0.5SiO4:xEu2+,yCe3+ blue phosphor synthesized by co‐precipitation method

In order to improve the luminescent performance of silicate blue phosphors, Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ phosphors were synthesized using one‐step calcination of a precursor prepared by chemical co‐precipitation. The crystal structure and luminescent properties of the phosphors were analyzed using X‐ray diffraction and fluorescence spectrophotometry, respectively. Because the activated ions (Eu²⁺) can occupy two different types of sites (Sr₁ and Sr₂), the emission spectrum of Eu²⁺ excited at 350 nm contains two single bands (EM₁ and EM₂) in the wavelength range 400–550 nm, centered at 463 nm, and the emission intensity first increases and then decreases with increasing concentrations of Eu²⁺ ions. Co‐doping of Ce³⁺ ions can greatly enhance the emission intensity of Eu²⁺ by transferring its excitation energy to Eu²⁺. Because of concentration quenching, a higher substitution concentration of Ce³⁺ can lead to a decrease in the intensity. Meanwhile, the quantum efficiency of the phosphor is improved after doping with Ce³⁺, and a blue shift phenomenon is observed in the CIE chromaticity diagram. The results indicate that Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ can be used as a potential new blue phosphor for white light‐emitting diodes.     

Tunable white light emission from single‐phased Li2SrSiO4:Dy3+ phosphors by co‐doping with Eu3+

A series of single‐phase full‐color emitting Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors were synthesized by solid‐state reaction and characterized by X‐ray diffraction and photoluminescence analyses. The samples showed emission peaks at 488 nm (blue), 572 nm (yellow), 592 nm (orange) and 617 nm (red) under 393 nm excitation. The photoluminescence excitation spectra, comprising the Eu–O charge transfer band and 4f–4f transition bands of Dy³⁺ and Eu³⁺, range from 200 to 500 nm. The Commission Internationale de I'Eclairage chromaticity coordinates for Li₂Sr_0.98−xSiO₄:0.02Dy³⁺,xEu³⁺ phosphors were simulated. By manipulating Eu³⁺ and Dy³⁺ concentrations, the color points of Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ were tuned from the greenish‐white region to white light and eventually to reddish‐white region, demonstrating that a tunable white light can be obtained by Li₂Sr_1−x−ySiO₄:xDy³⁺,yEu³⁺ phosphors. Li₂Sr_0.98−xSiO₄:0.02Dy³⁺, xEu³⁺ can serve as a white‐light‐emitting phosphor for phosphor‐converted light‐emitting diode. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of Mg doping in Sr2SiO4:Eu2+ nanophosphors for blue and white emission at near‐UV excitation

Nanophosphors of (Sr_0.98‐xMg_xEu_0.02)₂SiO₄ (x = 0, 0.18, 0.38, 0.58 and 0.78) were prepared through low temperature solution combustion method and their luminescence properties were studied. The emission peak for Eu²⁺ ?doped Sr₂SiO₄ nanophosphor is observed at ~490 nm and ~553 nm corresponding to two Sr²⁺ sites Sr(I) and Sr(II) respectively for 395 nm excitation. However the addition of Mg²⁺ dopant in Sr₂SiO₄ leads to suppression of ~553 nm emission peak due to absence of energy levels of Sr (II) sites which results in a single broad emission at ~460 nm. It was shown that the emission peak blue shifted with increase in Mg concentration which may be attributed to change in crystal field environment around Sr(I) sites. Therefore, the (Mg_0.78Sr_0.20Eu_0.02)₂SiO₄ nanophosphor can be used for blue emission and the Sr₂SiO₄:Eu_0.04²⁺ for green–yellow emission at 395 nm excitations. The Commission International de L'Eclairage (CIE) chromaticity coordinates for mixed powders of (Mg_0.78Sr_0.20Eu_0.02)₂SiO₄ and Sr₂SiO₄:Eu_0.04²⁺ (in a 1:1 ratio) fall in the white region demonstrating the possible use of the mixture in white light generation using near‐UV excitation source.     

Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+,Dy3+ co‐doped Ba2MgSi2O7 phosphors

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu²⁺‐doped and Eu²⁺,Dy³⁺‐co‐doped Ba₂MgSi₂O₇ (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid‐state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscopy (TEM) and energy‐dispersive X‐ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba₂MgSi₂O₇:Eu²⁺ showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba₂MgSi₂O₇:Eu²⁺Dy³⁺ showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f⁶ 5d¹ to 4f⁷ transition of Eu²⁺. TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu²⁺ doping in Ba₂MgSi₂O₇ phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy³⁺ ions were co‐doped in Ba₂MgSi₂O₇:Eu²⁺ and maximum TL intensity was observed for 2 mol% of Dy³⁺. TL emission spectra of Ba_1.95MgSi₂O₇:0.05Eu²⁺ and Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co‐doping. The trap depths were calculated to be 0.54 eV for Ba_1.95MgSi₂O₇:0.05Eu²⁺ and 0.54 eV and 0.75 eV for Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors. It was observed that co‐doping with small amounts of Dy³⁺ enhanced the thermoluminescence properties of Ba₂MgSi₂O₇ phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The following parts of the abstract have been edited for consistency. '4f65d1' has been corrected to '4f⁶ 5d¹', '4f7' has been corrected to '4f⁷', 'Ba1.95' has been corrected to 'Ba_1.95' and 'Ba1.93' has been corrected to 'Ba_1.93' respectively.]     

Cation‐tunable blue phosphor Ca2PO4Cl:Eu2+: enhancive emission and site occupancy

A series of blue phosphors Ca_1.98–xM_xPO₄Cl:0.02Eu²⁺ (M = Mg and Sr) with different values of x were synthesized using a high‐temperature solid‐state reaction. X‐Ray diffraction and photoluminescence measurements were used to study the phase structure and luminescence properties. Ca₂PO₄Cl:0.02Eu²⁺ exhibits a tunable emission intensity and color due to the incorporation of Sr²⁺ or Mg²⁺. The incorporation of Sr²⁺ reduces the luminescence intensity and results in a slight red shift in the emission band. The incorporation of Mg²⁺ results in enhanced emission and a clear blue shift in the emission band along with a tunable chromatic coordination. Under excitation at λ = 334 nm, the emission intensity of the Mg²⁺‐doped Ca₂PO₄Cl:0.02Eu²⁺ is found to be 250% that of Ca₂PO₄Cl:0.02Eu²⁺. The luminescence behaviors of the as‐synthesized phosphors are discussed according to the host crystal structure and site occupancy of Eu²⁺. The results indicate that Mg²⁺‐doped Ca₂PO₄Cl:Eu²⁺ is more applicable as a near‐UV‐convertible blue phosphor for white light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Sol–gel synthesis and luminescence property of Sr4Al2O7:Re3+,R+ (Re = Eu and Dy; R = Li,Na and K) phosphors for white LEDs

Sr₄Al₂O₇:Eu³⁺ and Sr₄Al₂O₇:Dy³⁺ phosphors with alkali metal substitution were prepared using a sol–gel method. The effects of a charge compensator R on the structure and luminescence of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors were investigated in detail. Upon heating to 1400°C, the structure of the prepared samples was that of the standard phase of Sr₄Al₂O₇. Under ultraviolet excitation, all Sr₄Al₂O₇:Eu³⁺,R⁺ samples exhibited several narrow emission peaks ranging from 550 to 700 nm due to the 4f → 4f transition of Eu³⁺ ions. All Sr₄Al₂O₇:Dy³⁺,R⁺ phosphors showed two emission peaks at 492 and 582 nm, due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. The luminescence intensity of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors improved markedly upon the addition of charge compensators, promoting their application in white light‐emitting diodes with a near‐ultraviolet chip.     

Luminescent properties of novel red‐emitting M7Sn(PO4)6:Eu3+ (M = Sr,Ba) for light‐emitting diodes

Novel red‐emitting phosphors, Eu³⁺‐activated M₇Sn(PO₄)₆ (M = Sr, Ba), were synthesized at 1200°C by conventional solid‐state reaction method. The luminescent properties of M₇Sn(PO₄)₆:Eu³⁺ (M = Sr, Ba) phosphors were investigated, and the critical concentration of the activator (Eu³⁺) concentration were found to be 0.175 mol and 0.21 mol per formula unit for Sr_7‐xSn(PO₄)₆:xEu³⁺ and Ba_7‐xSn(PO₄)₆:xEu³⁺, respectively. These phosphors presented red luminescence under the excitation of 395 or 465 nm, perfectly matching with the emissions wavelength of near‐ultraviolet (UV) light‐emitting diodes (LEDs) and InGaN blue LED.     

Insights into the discrepant luminescence for BaSiO3:Eu2+ phosphors prepared by solid‐state reaction and precipitation reaction methods

Two synthesis routes, solid‐state reaction and precipitation reaction, were employed to prepare BaSiO₃:Eu²⁺ phosphors in this study. Discrepancies in the luminescence green emission at 505 nm for the solid‐state reaction method sample and in the yellow emission at 570 nm for the sample prepared by the precipitation reaction method, were observed respectively. A detail investigation about the discrepant luminescence of BaSiO₃:Eu²⁺ phosphors was performed by evaluation of X‐ray diffraction (XRD), photoluminescence (PL)/photoluminescence excitation (PLE), decay time and thermal quenching properties. The results showed that the yellow emission was generated from the BaSiO₃:Eu²⁺ phosphor, while the green emission was ascribed to a small amount of Ba₂SiO₄:Eu²⁺ compound that was present in the solid‐state reaction sample. This work clarifies the luminescence properties of Eu²⁺ ions in BaSiO₃ and Ba₂SiO₄ hosts.     

Thermoluminescence properties of Eu‐doped and Eu/Dy‐codoped Sr2Al2SiO7 phosphors

We report the thermoluminescence properties of Sr_1.96Al₂SiO₇:Eu_0.04 and Sr_1.92Al₂SiO₇:Eu_0.04Dy_0.04 phosphors. These phosphors were prepared by a high‐temperature solid‐state reaction method. The prepared phosphors were characterized by X‐ray diffraction. A 254 nm source was used for ultraviolet (UV) irradiation and a ⁶⁰Co source was used for γ‐irradiation. The effect of heating rate and UV‐exposure were examined. The thermoluminescence temperature shifts to higher values with increasing heating rate and thermoluminescence intensity increases with increasing UV exposure time. The trapping parameters such as activation energy (E), order of kinetics and frequency factor (s) were calculated by peak shape method. The effect of γ‐ and UV‐irradiation on thermoluminescence studies was also examined.     

Effect of replacement of Ca by Zn on the structure and optical property of CaTiO3:Eu3+ red phosphor prepared by sol‐gel method

Eu³⁺‐doped calcium titanate red phosphors, Ca_1‐xZn_xTiO₃:Eu³⁺, were prepared by the sol‐gel method. The structure of prepared Ca_1‐xZn_xTiO₃:Eu³⁺ phosphors were investigated by X‐ray diffraction and infrared spectra. Due to the ⁵D₀ → ⁷F_1–3 electron transitions of Eu³⁺ ions, photoluminescence spectra showed a red emission at about 619 nm under excitation of 397 nm and 465 nm, respectively. When zinc was added to the host, the luminescent intensity of Ca_1‐xZn_xTiO₃:Eu³⁺ was markedly improved several fold compared with that of CaTiO₃:Eu³⁺. Ca_0.9Zn_0.1TiO₃:Eu³⁺ also had higher luminescence intensity than the commercially available Y₂O₃:Eu³⁺ phosphors under UV light excitation. Copyright © 2014 John Wiley & Sons, Ltd.     

Enhancement of the luminescence properties of Sr3(PO4)2:Dy3+,Li+ white‐light‐emitting phosphors by charge compensator Li+ co‐doping

Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors were prepared using a simple high temperature solid method for luminescence enhancement. The structures of the as‐prepared samples agreed well with the standard phase of Sr₃(PO₄)₂, even when Dy³⁺ and Li⁺ were introduced. Under ultraviolet excitation at 350 nm, the Sr₃(PO₄)₂:Dy³⁺ sample exhibited two emission peaks at 483 nm and 580 nm, which were due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. A white light was fabricated using these two emissions from the Sr₃(PO₄)₂:Dy³⁺ phosphors. The luminescence properties of Sr₃(PO₄)₂:Dy³⁺,Li⁺ phosphors, including emission intensity and decay time, were improved remarkably with the addition of Li⁺ as the charge compensator, which would promote their application in near‐ultraviolet excited white‐light‐emitting diodes.     

Sr2ZnWO6:Eu3+,Bi3+,Li+: a potential white‐emitting phosphor for near‐ultraviolet white light‐emitting diodes

A series of Sr₂ZnWO₆ phosphors co‐doped with Eu³⁺, Bi³⁺ and Li⁺ were prepared using the Pechini method. The samples were tested using X‐ray diffraction and luminescence spectroscopy. The results show that the samples can be effectively excited by near‐ultraviolet (UV) and UV light. The introduction of Bi³⁺ and Li⁺ significantly enhances the fluorescence emission of Sr₂ZnWO₆:Eu³⁺ and changes the light emitted by the phosphors from bluish‐green to white. When excited at 371 nm, Sr_2–x–zZn_1–yWO₆:xEu³⁺,yBi³⁺,zLi⁺ (x = 0.05, y = 0.05, z = 0.05, 0.1 and 0.15) samples emit high‐performance white light. Intense red–orange emission is also observed when excited by UV light. The obtained phosphor is a potential white‐emitting phosphor that could meet the needs of excitation sources with near‐UV chips. In addition, this phosphor might have promising application as a red–orange emitting phosphor for white light‐emitting diodes based on UV light‐emitting diodes. Copyright © 2015 John Wiley & Sons, Ltd.     

Influence of Tl+ activator ions on the luminescence characteristics of KCl0.5Br0.5:Eu2+ powder phosphors

Photoluminescence (PL) of thallium co‐doped with KCl_0.5Br_0.5:Eu²⁺ powder phosphors display emission bands at 320 and 370 nm attributable to centres involving Tl⁺ ions in addition to characteristic Eu²⁺ emission around 420 nm. Additional PL excitation and emission bandS observed around 260 and 380 nm, respectively, were observed in the double‐doped KCl_0.5Br_0.5:Eu²⁺, Tl⁺ powder phosphors and are attributed to complex centres involving Tl⁺ and Eu²⁺ ions. The enhancement observed in the intensity of Eu²⁺ emission around 420 nm with the addition of TlBr in KCl_0.5Br_0.5:Eu²⁺ powder phosphors is attributed to the energy transfer from Tl⁺ → Eu²⁺ ions. Photostimulated luminescence (PSL) studies of γ‐irradiated KCl_0.5Br_0.5:Eu²⁺, Tl⁺ mixed phosphors are reported and a tentative PSL mechanism in the phosphors has been suggested. Copyright © 2009 John Wiley & Sons, Ltd.     

Photoluminescent properties of Eu3+‐Eu2+ activated MAl2SixO2x + 4 (M = Mg,Ca, Sr,Ba) phosphors prepared in air

In this paper, MAl₂Si_xO_2x+4:Eu²⁺/Eu³⁺ (Eu²⁺ + Eu³⁺ = 2%, molar ratio; M = Mg, Ca, Sr, Ba; x = 0, 0.5, 1, 1.5, 2) phosphors with different SiO₂ concentrations (the ratio of SiO₂ to MAl₂O₄ is n%, n = 0, 50, 100, 150, 200, respectively) were prepared by high‐temperature solid‐state reaction under atmospheric air conditions. Their structures and photoluminescent properties were systematically researched. The results indicate that Eu³⁺ ions have been reduced and Eu²⁺ ions are obtained in air through the self‐reduction mechanism. The alkaline earth metal ions and doping SiO₂ strongly affect the crystalline phase and photoluminescent properties of samples, including microstructures, relative intensity of Eu²⁺ to Eu³⁺, location of emission lines/bands. It is interesting and important that the emission color and intensities of europium‐doped various phosphors which consist of aluminosilicate matrices prepared under atmospheric air conditions could be modulated by changing the kinds of alkaline earth metal and the content of SiO₂.     

Luminescence behavior of Li2Sr1‐3x/2EuxSiO4 red phosphors for LED applications

Red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ 0≤x≤0.5) phosphors were synthesized at 900°C in air by a solid‐state reaction. The synthesized phosphors were characterized by X‐ray powder diffraction, photoluminescence (PL) excitation (PLE) and PL spectra. The results from the PLE spectra suggest that the strong 394 nm excitation peak associated with the ⁵L₆ state of Eu³⁺ ions is of significance for near ultraviolet pumped white light‐emitting diodes and solid‐state lighting. It is also noted that the position of the charge transfer state of Eu³⁺ ions shifts towards the higher energy side (blue shift) by increasing the content of Eu³⁺ ions. The predominant emissions of Eu³⁺ ions under 394 nm excitation are observed at 580, 593, 614, 656 and 708 nm, which are attributed to the ⁵D₀ → ⁷F_J (J = 0, 1, 2, 3 and 4), respectively. The PL results reveal that the optimal content of the red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ phosphors is x = 0.475. Simulation of the white light excited by 394 nm near ultraviolet light has also been carried out for its potential white light‐emitting diode applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Luminescent properties of MAl(SO4)2Br:Eu3+ (M = Sr or Mg) red phosphors for near‐UV light‐emitting diodes

Eu³⁺‐activated MAl(SO₄)₂Br phosphors (where M = Mg or Sr) are successfully prepared using a wet chemical reaction technique. The samples are characterized by X‐ray diffraction (XRD) and photoluminescence (PL) spectroscopies. The XRD pattern revealed that both the samples are microcrystalline in nature. PL of Eu³⁺‐doped SrAl(SO₄)₂Br and MgAl(SO₄)₂Br phosphors exhibited characteristic red emission coming from the ⁵D₀ → ⁷F₂ (616 nm) electron transition, when excited by 396 nm wavelength of light. The maximum intensity of luminescence was observed at a concentration of 1 mol% Eu³⁺. The intensity of the electric dipole transition at 616 nm is greater than that of the magnetic dipole transition at 594 nm. The results showed that MAl(SO₄)₂Br:Eu³⁺, (M = Mg, Sr) phosphors have potential application in near‐UV light‐emitting diodes as efficient red‐emitting phosphor. Copyright © 2014 John Wiley & Sons, Ltd.     

Hydrothermal growth of Zn2SnO4:Eu,Ca for red emission

Zinc stannate (Zn₂SnO₄) and Zn₂SnO₄ codoped with Eu³⁺ and Ca²⁺ (ZTO:Eu,Ca) were synthesized by hydrothermal method and characterized with X‐ray diffraction (XRD), energy‐dispersive X‐ray analysis (EDAX), Raman spectrometer, field emission scanning electron microscopy (FESEM), ultraviolet‐visible (UV‐vis) and photoluminescence (PL) spectrophotometers. PL analysis of Zn₂SnO₄ gives broad defect induced emission in the region 500–750 nm. The crystal structure of Zn₂SnO₄ was retained even with a nominal doping of Eu, Ca and its combination in the Zn₂SnO₄. The Eu³⁺ ions were found to occupy the non‐centrosymmetric sites of the Zn₂SnO₄ and gave emissions at 592, 615 and 702 nm. Zn₂SnO₄:Eu,Ca showed red emission at 615 nm attributed to the electronic transition from the excited state ⁵D₀ → ⁷F₂ of the 4f⁶ configuration of Eu³⁺. Nominal codoping of Eu³⁺ and Ca²⁺ ions promoted the quenching of orange emission from Eu³⁺ in Zn₂SnO₄:Eu,Ca.     

Optical properties of Eu2+/Eu3+ mixed valence phosphor Ca2SiO2F2:Eu2+/Eu3+

The Eu²⁺/Eu³⁺ mixed valence phosphor Ca₂SiO₂F₂:Eu²⁺/Eu³⁺ was prepared using a solid‐state reaction synthesis method in a CO atmosphere, and the optical properties were investigated. The spectroscopic properties revealed that Ca²⁺ ions were occupied by both Eu²⁺ and Eu³⁺ ions in Ca₂SiO₂F₂, and both ions were able to generate their characteristic emissions. A broad 5d → 4f Eu²⁺ band at ~470 nm and narrow 4f → 4f Eu³⁺ peaks upon excitation with n‐UV light were observed. The ratio between Eu²⁺ and Eu³⁺ emissions changed regularly, and the relative intensity of the red component from Eu³⁺ became systematically stronger with increasing overall Eu content. As a result, the emission color of these phosphors can be tunable from blue to pink under n‐UV light excitation.     

Photoluminescence in K3Ca2(SO4)3Cl‐doped Eu3+ phosphor

In this article we report Eu³⁺ luminescence in novel K₃Ca₂(SO₄)₃Cl phosphors prepared by wet chemical methods. The Eu³⁺ emission was observed at 594 nm and 615 nm, keeping the excitation wavelength constant at 396 nm nearer to light‐emitting diode excitation, Furthermore, phosphors were characterized by X‐ray diffraction for the confirmation of crystallinity. The variation of the photoluminescence intensity with impurity concentration has also been discussed. Thus, prominent emission in the red region makes prepared phosphors more applicable for white light‐emitting diodes. Copyright © 2013 John Wiley & Sons, Ltd.