Development of an optical sensor for chlortetracycline detection based on the fluorescence quenching of l‐tryptophan

A simple and selective spectrofluorimetric method for the detection of chlortetracycline (CTC) was studied. In pH 7.4 buffer medium l ‐tryptophan (l ‐Trp), applied as the fluorescence probe, interacted with CTC resulting in fluorescence quenching of the probe. CTC was detected with maximum excitation and emission wavelengths at λ_ex/λ_em = 275/350 nm. Notably, quenching of fluorescence intensities was positively proportional to the CTC concentration over the range of 0.65–30 μmol L^?1 and the limit of detection was 0.2 μmol L^?1. Effect of temperature shown in Stern?Volmer plots, absorption spectra and fluorescence lifetime determination, indicated that fluorescence quenching of l ‐Trp by CTC was mainly by static quenching. The proposed study used practical samples analysis satisfactorily.     

Silver nanoclusters stabilized with denatured fish sperm DNA and the application on trace mercury ions detection

In this study, fluorescent silver nanoclusters (Ag NCs) were synthesized using denatured fish sperm DNA as the template. In contrast to other methods, this method did not use artificial DNA as the template. After their reaction with denatured fish sperm DNA, Ag⁺ ions were reduced by NaBH₄ to form Ag NCs. The Ag NCs showed a strong fluorescence emission at 650 nm when excited at 585 nm. The fluorescence intensity increased fourfold at pH 3.78, controlled with Britton–Robinson buffer solution. The fluorescence of the Ag NCs was quenched in the presence of trace mercury ions (Hg²⁺) in a weakly acidic medium and nitrogen atmosphere. The extent of the fluorescence quenching of Ag NCs strongly depends on the Hg²⁺ ion concentration over a linear range from 2.0 nmol L^?1 to 3.0 μmol L^?1. The detection limit (3σ/k) for Hg²⁺ was 0.7 nmol L^?1. Thus, a sensitive and rapid method was developed for the detection of Hg²⁺ ions.     

Characterization of a highly Al3+‐selective fluorescence probe based on naphthalimide‐Schiff base and its application to practical water samples

A new fluorescent Al³⁺‐probe, N‐allyl‐4‐[3,3′‐((2‐aminoethyl)azanediyl)‐bis(N´‐(2‐hydroxybenzylidene)propanehy‐drazide)]‐1,8‐naphthalimide ( L ), was designed and synthesized based on 1,8‐naphthalimide. The probe L contains 1,8‐naphthalimide moiety as the fluorophore and a Schiff base as the recognition group. The structure of L was determined by single crystal X‐ray. L emission at 526 nm increased on addition of Al³⁺ under excitation wavelength at 350 nm. L exhibited high selectivity and sensitivity fluorescence emission towards to Al³⁺ in ethanol/Tris–HCl buffer solution (1:1, v/v, pH = 7.2) as compared with other tested metal ions. A good linearity with a correlation coefficient (R²) of 0.99 was observed in the concentration range 2–10 μM. The binding constant and the detection limit of L for Al³⁺ were calculated to 2.6 × 10⁴ M^?1 and 0.34 μM, respectively. The results of experiments that including Job plot, ultraviolet–visible (UV–Vis) light titration, fluorescence titration, ESI‐MS and ¹H NMR titration, indicated a 1:1 stoichiometric complex between L and Al³⁺. L was highly effective in monitoring Al³⁺ in real‐life Yellow River and tap water samples.     

β‐Cyclodextrin protected Cu nanoclusters as a novel fluorescence sensor for graphene oxide in environmental water samples

This paper proposed a simple and sensitive approach for detecting graphene oxide (GO) in a wide pH range in environmental water samples using fluorescent β‐CD protected Cu NCs based on the hydrogen‐bond interactions between GO and 6‐SH‐β‐CD. The influences of dilution ratio and pH were investigated. We found that the fluorescence quenching efficiency of Cu NCs by GO remained almost the same under pH from 4 to 10, which benefitted the monitoring of GO under different pH conditions in real samples. The fluorescence quenching mechanism was also discussed. The fluorescence of β‐CD protected Cu NCs could be quenched in the presence of GO with a lowest detection concentration of 0.1 mg·L^?1. Good linear correlations were obtained over the concentration range from 0 to 30 mg·L^?1 at different pH values (pH = 4, pH = 7 and pH = 12). In addition, this method was successfully applied to the determination of GO in real samples which presents more opportunities for application in environmental and material sciences.     

A highly selective fluorescent chemosensor for Cu2+: synthesis and properties of a rhodamine B‐containing diarylethene

A diarylethene bearing a triazole‐linked rhodamine B unit was synthesized. Its fluorescent emission was significantly enhanced in the presence of protons or Cu²⁺ due to transformation from the pirocyclic form to open‐ring form. The fluorescence was quenched sequentially upon irradiation with 297 nm light based on the intramolecular fluorescence resonance energy transfer mechanism. In an acetonitrile: water binary solvent (1: 1 v /v), the compound showed significant fluorescent enhancement for Cu²⁺ compared with a wide range of tested metal ions with a fast response and a limit of detection of 2.86 × 10^?8 mol L^?1. Using Cu²⁺ and UV light as the chemical inputs, and fluorescence intensity at 597 nm as the output, a logic gate was developed at the molecular level. Moreover, the compound can be used with a high accuracy to detect Cu²⁺ in a natural water sample.     

A novel spectrofluorimetric method for determination of imatinib in pure,pharmaceutical preparation,human plasma,and human urine

The following paper represents a simple, highly sensitive, responsive validated and developed spectrofluorimetric method for estimation of imatinib (IMB) in its pure, commercial preparation, human urine and human blood plasma. The calibration curve was in the range 4–900 ng ml^?1 for pure form and urine and 8–900 ng ml^?1 for plasma in a medium contains carboxymethyl cellulose (CMC) and acetate buffer (pH 5) with excitation wavelength (λ_ex) 230 nm and emission wavelength (λ_em) 307 nm. The limit of detection (LOD) was 0.37 ng ml^?1 for the pure form, 0.64 ng ml^?1 for human urine, and 0.70 ng ml^?1 for human plasma, while the limit of quantitation (LOQ) was 1.2 for pure form, 1.91 for urine and 2.1 for plasma. The suggested method was successfully applied for evaluation of IMB in tablets within 99% mean percentage recovery. The excipients that are usually used as additives in pharmaceutical dosage form did not interfere with the suggested method. The method was efficiently used for estimation of IMB in human urine and human plasma. The effect of some cations that might be present in urine and plasma was also studied. The method was also focused on human volunteers and in vitro drug release.     

Intermolecular interaction of fosinopril with bovine serum albumin (BSA): The multi‐spectroscopic and computational investigation

The intermolecular interaction of fosinopril, an angiotensin converting enzyme inhibitor with bovine serum albumin (BSA), has been investigated in physiological buffer (pH 7.4) by multi‐spectroscopic methods and molecular docking technique. The results obtained from fluorescence and UV absorption spectroscopy revealed that the fluorescence quenching mechanism of BSA induced by fosinopril was mediated by the combined dynamic and static quenching, and the static quenching was dominant in this system. The binding constant, K_b, value was found to lie between 2.69 × 10³ and 9.55 × 10³ M^?1 at experimental temperatures (293, 298, 303, and 308 K), implying the low or intermediate binding affinity between fosinopril and BSA. Competitive binding experiments with site markers (phenylbutazone and diazepam) suggested that fosinopril preferentially bound to the site I in sub‐domain IIA on BSA, as evidenced by molecular docking analysis. The negative sign for enthalpy change (ΔH⁰) and entropy change (ΔS⁰) indicated that van der Waals force and hydrogen bonds played important roles in the fosinopril‐BSA interaction, and 8‐anilino‐1‐naphthalenesulfonate binding assay experiments offered evidence of the involvements of hydrophobic interactions. Moreover, spectroscopic results (synchronous fluorescence, 3‐dimensional fluorescence, and Fourier transform infrared spectroscopy) indicated a slight conformational change in BSA upon fosinopril interaction.     

Localization of polyphosphates in Saccharomyces fragilis, as revealed by 4′,6-diamidino-2-phenylindole fluorescence

The fluorescent dye 4′,6-diamidino-2-phenylindole has its emission maximum at 456 nm. Fluorescence intensity at this wavelength is significantly increased by various negatively-charged polyelectrolytes. Among several polyelectrolytes tested, polyphosphates appeared to be unique in the sense that they shifted the emission maximum from 456 to 526 nm. Addition of Saccharomyces fragilis cells to a diamidinophenylindole solution caused an immediate shift of the emission maximum to 526 nm, followed by a gradual increase of fluorescence at 456 nm. The 526 nm, but not the 456 nm fluorescence was instantly quenched by non-penetrating cations, like UO²⁺₂. These results suggest a momentary interaction of diamidinophenylindole with polyphosphate, localized outside the plasma membrane, followed by a slow penetration of the dye into the cells, yielding increased fluorescence at 456 nm by interaction of the dye with e.g., nucleic acids. This was confirmed by fluorescence microscopy. After addition of diamidinophenylindole the yeast cells exhibited an immediate green-yellow fluorescence of the membrane, that was suppressed by UO²⁺₂. After longer incubation times the cytoplasm and nucleus developed a blue fluorescence.     

Effects of the interaction between Na2Wo4‐6‐benzylaminopurine anionic chelate and rhodamine 6G on the resonance Rayleigh scattering and fluorescence spectra and their analytical applications

In pH 4.99‐6.06 Britton‐Robinson (BR) buffer medium, 6‐benzylaminopurine (6‐BA) reacted with Na₂WO₄ to form 1:1 anionic chelate (6‐BA·WO₄)^2‐, which further reacted with rhodamine 6G to form ternary ion complexes at room temperature. This resulted in a significant enhancement of resonance Rayleigh scattering (RRS) with a maximum RRS wavelength of 316 nm. Meanwhile, the fluorescence of the solution was quenched and excitation (λ_ex) and emission (λ_em) wavelengths of the fluorescence were 290 and 559 nm, respectively. Intensities of RRS enhancing (ΔI_RRS) and fluorescence quenching (ΔI_F) were directly proportional to concentrations of 6‐BA. As a result, RRS and fluorescence quenching for determination of trace amounts of 6‐BA were developed. Under optimal conditions, linear ranges and detection limits of the two methods were 0.05‐15.00 µg/mL and 8.2 ng/mL (RRS), 0.50‐15.00 µg/mL and 17.0 ng/mL, respectively. It was found that the RRS method was superior to fluorescence quenching. The influence of these methods were investigated and results showed that RRS had good selectivity. RRS was applied to determine 6‐BA in vegetable samples with satisfactory results. Furthermore, the reaction mechanisms of the ternary ion‐association system are discussed. In addition, the polarization experiment revealed that the resonance light scattering (RLS) peak of Na₂WO₄‐6‐BA‐R6G consisted mainly of depolarized resonance fluorescence and resonance scattering. It was speculated that light emission fluorescence energy (E_L) transformed into resonance light scattering energy (E_RLS), which was a key reason for enhancement of RRS. Copyright © 2012 John Wiley & Sons, Ltd.     

Enhancing the luminescence of Eu3+/Eu2+ ion‐doped hydroxyapatite by fluoridation and thermal annealing

This paper reports a novel way for the synthesis of a europium (Eu)‐doped fluor‐hydroxyapatite (FHA) nanostructure to control the luminescence of hydroxyapatite nanophosphor, particularly, by applying optimum fluorine concentrations, annealed temperatures and pH value. The Eu‐doped FHA was made using the co‐precipitation method followed by thermal annealing in air and reducing in a H₂ atmosphere to control the visible light emission center of the nanophosphors. The intensities of the OH^? group decreased with the increasing fluorine concentrations. For the specimens annealed in air, the light emission center of the nanophosphor was 615 nm, which was emission from the Eu³⁺ ion. However, when they were annealed in reduced gas (Ar + 5% H₂), a 448 nm light emission center from the Eu²⁺ ion of FHA was observed. The presence of fluorine in Eu‐doped FHA resulted in a significant enhancement of nanophosphor luminescence, which has potential application in light emission and nanomedicine.     

Core–shell structured CdTe/CdS@SiO2@CdTe@SiO2 composite fluorescent spheres: Synthesis and application for Cd2+ detection

Core–shell structured quantum dot (QD)–silica fluorescent nanoparticles have attracted a great deal of attention due to the excellent optical properties of QDs and the stability of silica. In this study, core–shell structured CdTe/CdS@SiO₂@CdTe@SiO₂ fluorescent nanospheres were synthesized based on the Stöber method using multistep silica encapsulation. The second silica layer on the CdTe QDs maintained the optical stability of nanospheres and decreased adverse influences on the probe during subsequent processing. Red‐emissive CdTe/CdS QDs (630 nm) were used as a built‐in reference signal and green‐emissive CdTe QDs (550 nm) were used as a responding probe. The fluorescence of CdTe QDs was greatly quenched by added S^2?, owing to a S^2?‐induced change in the CdTe QDs surface state in the shell. Upon addition of Cd²⁺ to the S^2?‐quenched CdTe/CdS@SiO₂@CdTe@SiO₂ system, the responding signal at 550 nm was dramatically restored, whereas the emission at 630 nm remained almost unchanged; this response could be used as a ratiometric ‘off–on’ fluorescent probe for the detection of Cd²⁺. The sensing mechanism was suggested to be: the newly formed CdS‐like cluster with a higher band gap facilitated exciton/hole recombination and effectively enhanced the fluorescence of the CdTe QDs. The proposed probe shows a highly sensitive and selective response to Cd²⁺ and has potential application in the detection of Cd²⁺ in environmental or biological samples.     

A porphyrin‐based fluorescence method for zinc determination in commercial propolis extracts without sample pretreatment

The quantification of zinc in over‐the–counter drugs as commercial propolis extracts by molecular fluorescence technique using meso ‐tetrakis(4‐carboxyphenyl)porphyrin (H₂TCPP⁴) was developed for the first time. The calibration curve is linear from 6.60 to 100 nmol L^?1 of Zn²⁺. The detection and quantification limits were 6.22 nmol L^?1 and 19.0 nmol L^?1, respectively. The reproducibility and repeatability calculated as the percentage variation of slopes of seven calibration curves were 6.75% and 4.61%, respectively. Commercial propolis extract samples from four Brazilian states were analyzed and the results (0.329–0.797 mg/100 mL) obtained with this method are in good agreement with that obtained with the Atomic Absorption Spectroscopy (AAS) technique. The method is simple, fast, of low cost and allows the analysis of the samples without pretreatment. Moreover the major advantage is that Zn‐porphyrin complex presents fluorescent characteristic promoting the selectivity and sensitivity of the method.     

High‐performance liquid chromatography study of gatifloxacin and sparfloxacin using erythrosine as post‐column resonance Rayleigh scattering reagent and mechanism study

Herein, a highly selective high‐performance liquid chromatography (HPLC) coupled with resonance Rayleigh scattering (RRS) method was developed to detect gatifloxacin (GFLX) and sparfloxacin (SPLX). GFLX and SPLX were first separated by HPLC, then, in pH 4.4 Britton–Robinson (BR) buffer medium, protonic quaternary ammonia cation of GFLX and SPLX reacted with erythrosine (ERY) to form 1:1 ion‐association complexes, which resulted in a significant enhancement of RRS signal. The experimental conditions of HPLC and post‐column RRS have been investigated, including detection wavelength, flow rate, pH, reacting tube length and reaction temperature. Reaction mechanism were studied in detail by calculating the distribution fraction. The maximum RRS signals for GFLX and SPLX were recorded at λ_ex = λ_em = 330 nm. The detection limits were 3.8 ng ml^?1 for GFLX and 17.5 ng ml^?1 for SPLX at a signal‐to‐noise ratio of 3. The developed method was successfully applied to the determination of GFLX and SPLX in water samples. Recoveries from spiked water samples were 97.56–98.85%.     

Pharmacokinetic evaluation of daclatasvir and ledipasvir in healthy volunteers using a validated highly sensitive spectrofluorimetric method

A simple, highly sensitive and selective spectrofluorimetric method has been developed and fully validated for the determination of daclatasvir (DAC) and ledipasvir (LED) in tablets and human plasma. The method is based on measurement of the native fluorescence in methanol at λ_em 384 nm after excitation at λ_ex 318 nm for DAC and in acetonitrile at λ_em 402 nm after excitation at λ_ex 340 nm for LED. The fluorescence intensity (FI) concentration plot was rectilinear over the ranges 1.2–12, 0.1–18 ng ml^?1 and 9–90, 1–100 ng ml^?1 with a good correlation of r = 0.9994 to r = 0.9997 in standard solution and human plasma for DAC and LED, respectively. The extraction of analytes from plasma was performed using methanol and acetonitrile as a precipitating agent with lower limit of quantification (LLOQ) of 0.1 and 1.0 ng ml^?1 for DAC and LED; respectively. The proposed method was validated according to the US Food and Drug Administration (FDA) guidelines and successfully applied for estimating the pharmacokinetic parameters of DAC and LED following oral administrations of their tablets.     

Amiloride sensitivity of proton-conductive pathways in gastric and intestinal apical membrane vesicles

Summary Passive proton permeability of gastrointestinal apical membrane vesicles was determined. The nature of the pathways for proton permeation was investigated using amiloride. The rate of proton permeation (k _H ⁺ was determined by addition of vesicles (pH _i = 6.5) to a pH 8.0 solution containing acridine orange. The rate of recovery of acridine orange fluorescence after quenching by the acidic vesicles ranged from 4 × 10^–3 (gastric parietal cell stimulation-associated vesicles; SAV) and 5 × 10^–3 (duodenal brush-border membrane vesicles; dBBMV) to 11 × 10+^–3 sec^–1 (ileal BBMV; iBBMV). Amiloride, 0.03 and 0.1 mm, significantly reduced the rate of proton permeation in dBBMV and iBBMV, but not gastric SAV. The decreases in k _H ⁺ were proportionately greater in iBBMV as compared with dBBMV. The presence of Na⁺/H⁺ exchange was demonstrated in both dBBMV and iBBMV by proton-driven (pH _i < pH _o ) ²²Na⁺ uptake. Evidence was also sought for the conductive nature of pathways for proton permeation. Intravesicular acidification, again determined by quenching of acridine orange fluorescence, was observed during imposition of K⁺-diffusion potential ([K⁺] _i [K⁺ _o ). In dBBMV and iBBMV, intravesicular acidification was enhanced in the presence of the K⁺-ionophore valinomycin, indicating that the native K⁺ permeability is rate limiting. In the presence of valinomycin, the K⁺-diffusion potential drove BBMV intravesicular acidification to levels close to the electrochemical potential. In gastric SAV, acidification was not limited by the K⁺ permeability. Valinomycin was without effect, but the K⁺/H⁺ ionophore nigericin enhanced acidification in gastric SAV, illustrating the low proton permeability of these membranes. Amiloride, 0.03–1 mm, resulted in concentration-dependent reductions of K⁺-diffusion potential-driven acidification in dBBMV and iBBMV but not in gastric SAV. These data demonstrate that proton permeation in the three membrane types is rheogenic. The sensitivity of the proton-conductive pathways in intestinal BBMV to high concentrations of amiloride correlated with the presence of the Na⁺/H⁺ antiport and indicates that this transmembrane protein may represent a pathway for proton permeation.We thank Ruth Briggs for assistance with the Na/H exchange experiments. This work was supported by a grant from the Medical Research Council (G8418056CA).     

Akaline,saline and mixed saline–alkaline stresses induce physiological and morpho‐anatomical changes in Lotus tenuis shoots

Saline, alkaline and mixed saline–alkaline conditions frequently co‐occur in soil. In this work, we compared these plant stress sources on the legume Lotus tenuis, regarding their effects on shoot growth and leaf and stem anatomy. In addition, we aimed to gain insight on the plant physiological status of stressed plants. We performed pot experiments with four treatments: control without salt (pH = 5.8; EC = 1.2 dS·m^?1) and three stress conditions, saline (100 mm NaCl, pH = 5.8; EC = 11.0 dS·m^?1), alkaline (10 mm NaHCO₃, pH = 8.0, EC = 1.9 dS·m^?1) and mixed salt–alkaline (10 mm NaHCO₃ + 100 mm NaCl, pH = 8.0, EC = 11.0 dS·m^?1). Neutral and alkaline salts produced a similar level of growth inhibition on L. tenuis shoots, whereas their mixture exacerbated their detrimental effects. Our results showed that none of the analysed morpho‐anatomical parameters categorically differentiated one stress from the other. However, NaCl‐ and NaHCO₃‐derived stress could be discriminated to different extents and/or directions of changes in some of the anatomical traits. For example, alkalinity led to increased stomatal opening, unlike NaCl‐treated plants, where a reduction in stomatal aperture was observed. Similarly, plants from the mixed saline–alkaline treatment characteristically lacked palisade mesophyll in their leaves. The stem cross‐section and vessel areas, as well as the number of vascular bundles in the sectioned stem were reduced in all treatments. A rise in the number of vessel elements in the xylem was recorded in NaCl‐treated plants, but not in those treated exclusively with NaHCO_3.     

Photosynthetic control, “energy-dependent” quenching of chlorophyll fluorescence and photophosphorylation under influence of tertiary amines

The effects of the tertiary amines tetracaine, brucine and dibucaine on photophosphorylation and control of photosynthetic electron transport in isolated chloroplasts of Spinacia oleracea were investigated. Tertiary amines inhibited photophosphorylation while the related electron transport decreased to the rates, observed under non-phosphorylating conditions. Light induced quenching of 9-aminoacridine fluorescence and uptake of ¹⁴C-labelled methylamine in the thylakoid lumen declined in parallel with photophosphorylation, indicating a decline of the transthylakoid proton gradient. In the presence of ionophoric uncouplers such as nigericin, no effect of tertiary amines on electron transport was seen in a range of concentration where photophosphorylation was inhibited. Under the influence of the tertiary amines tested, pH-dependent feed-back control of photosystem II, as indicated by energy-dependent quenching of chlorophyll fluorescence, was unaffected or even increased in a range of concentration where 9-aminoacridine fluorescence quenching and photophosphorylation were inhibited. The data are discussed with respect to a possible involvement of localized proton flow pathways in energy coupling and feed-back control of electron transport.Abbreviations 9-AA 9-aminoacridine - J _e flux of photosynthetic electron transport - PC photosynthetic control - pH₁ H⁺ concentration in the thylakoid lumen - pmf proton motive force - _P potential quantum yield of photochemistry of photosystem II (with open reaction centers) - Q _A primary quinone-type electron acceptor of photosystem II - q _Q photochemical quenching of chlorophyll fluorescence - q _E energy-dependent quenching of chlorophyll fluorescence - q _AA light-induced quenching of 9-amino-acridine fluorescence     

Correlation of the photosystem I and II reaction center chlorophyll-protein complexes, CP-a1 and CP-aII with photosystem activity and low temperature fluorescence emission properties in mutants of Scenedesmus

Abstract Comparative studies on the low temperature fluorescence emission of whole cells, purified chlorophyll-protein (CP) complexes and on patterns noted in sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE) for chlorophyll-protein complexes and chloroplast membrane polypeptides of Scenedesmus obliquus with several distinct mutant classes has allowed further correlation between the fluorescence emission bands seen at 77K and the known chlorophyll-protein complexes. In mutants deficient in photosystem II (PS-II; total loss of the reducing side) the fluorescence emission spectra showed only two peaks, i.e., 686 and 718 nm, but in the wild type, in mutants lacking the oxidizing side of PS-II and in phenotypes missing the CP-a₁ complex (and P-700 activity) all three emission bands at 686, 696 and 718 nm were present. In a mutant lacking the light-harvesting CP-a/b complex the emission peak at 686 nm was strongly reduced and the longer wavelength emissions predominated. Gel electrophoresis studies showed that the PS-II (reducing side) mutants lacked the polypeptides of apparent molecular weight 54 and 51 kilodaltons and the chlorophyll-protein complex, CP-a_II, of apparent molecular weight 32 kilodaltons. Contrarily, the loss of the oxidizing side of PS-II did not result in any alteration of these components. Genetic deletion of CP-a₁ did not alter significantly the long wavelength emission even though the isolated CP-a₁ shows the low temperature-dependent long wavelength emission comparable to that seen in the whole cell. It was deduced that remaining PS-I antennae chlorophylls must account for the emission seen at 718 nm. The absence of the CP-a/b complex and the strong simultaneous decrease of the 686 nm emission strengthens the concept that this complex is the primary emitter of fluorescence at room temperature. Its absence facilitated the detection of the CP-a_II complex in SDS-PAGE and enhanced the in vivo fluorescence by the two photosystems. Parallel experiments with two mutants which green and develop, one to the wild-type and the other to the CP-a/b deficient phenotype, provided additional evidence for the source of the low temperature emission bands.     

Differential action of Hg2+ and Cd2+ on the phycobilisomes and chlorophyll a fluorescence,and photosystem II dependent electron transport in the cyanobacterium Anabaena flos-aquae

The effect of equimolar concentrations of Hg²⁺ and Cd²⁺ on the whole cell absorption spectra, absorption spectra of the extracted phycocyanin (PC) and fluorescence emission spectra of phycobilisomes (PBS) was investigated in the cells of Anabaena flos-aquae. The PC component of the PBS was found to be extremely sensitive to the Hg²⁺ rather than the Cd²⁺ ions. Further, the results showed that Hg²⁺ and Cd²⁺ induced decrease in the rate of Hill activity (H₂O - DCPIP) was partially restored by the electron donor NH₂OH, not by the diphenyl carbazide. Similarly, chlorophyll a fluorescence emission in the presence of metals showed that addition of NH₂OH could effectively reverse the metal induced alterations in the fluorescence emission intensity. These results, together, suggested that Hg²⁺ and Cd²⁺ caused damage to the photosystems (PS) II reaction center. However, a relatively higher stimulation of the chlorophyll a emission at 695 nm with a red shift of 4.0 nm in the presence of Hg²⁺, and Cd²⁺ induced preferential decrease in the emission intensity at 676 nm as compared with the peak at 695 nm were indicative of the differential action of Hg²⁺ and Cd²⁺ on the PS II.