Field trials of a TiO2 pellet‐based photocatalytic reactor for off‐gas treatment at a soil vapor extraction well

A field trial of a pilot‐scale TiO₂ photocatalytic reactor for treatment of off‐gases from a soil vapor extraction (SVE) well at a chlorinated solvent spill site at the Savannah River Site near Aiken, SC, is described. Trichloroethylene (TCE), perchloroethylene (PCE), 1,1‐dichloroethylene (1,1 ‐DCE), and 1,1,1 ‐trichloroethane (1,1,1 ‐TCA) were treated at flow rates up to 6 1/min and space times of 5.1 x 10⁷ to 1.2 x 10⁹ g/mol. The TiO₂ used was in the form of porous pellets with a surface area of 150 m²/g. Operation of the reactor with the undiluted waste stream (5000 ppmv) at 80, 100, and 110°C yielded many undesirable byproducts, such as phosgene, chloroform, carbon tetrachloride, and penta‐ and hexachloroethane, even though the conversion of PCE and TCE approached 100%. After diluting the waste stream with ambient air to below 1000 ppmv and maintaining space times around 5 x 10⁸ g/mol, a conversion >99.5% was achieved with the production of only small amounts (<10 ppmv) of hexachloroethane. The reactor was Operated continuously for 8 d, with no noticeable deterioration in catalyst activity. In a subsequent laboratory study to determine the mass balance, CO₂ determined in the reactor effluent accounted for 80% of the influent carbon.     

Surface Engineering of TiO2 ETL for Highly Efficient and Hysteresis‐Less Planar Perovskite Solar Cell (21.4%) with Enhanced Open‐Circuit Voltage and Stability

Interfacial studies and band alignment engineering on the electron transport layer (ETL) play a key role for fabrication of high‐performance perovskite solar cells (PSCs). Here, an amorphous layer of SnO₂ (a‐SnO₂) between the TiO₂ ETL and the perovskite absorber is inserted and the charge transport properties of the device are studied. The double‐layer structure of TiO₂ compact layer (c‐TiO₂) and a‐SnO₂ ETL leads to modification of interface energetics, resulting in improved charge collection and decreased carrier recombination in PSCs. The optimized device based on a‐SnO₂/c‐TiO₂ ETL shows a maximum power conversion efficiency (PCE) of 21.4% as compared to 19.33% for c‐TiO₂ based device. Moreover, the modified device demonstrates a maximum open‐circuit voltage (V_oc) of 1.223 V with 387 mV loss in potential, which is among the highest reported value for PSCs with negligible hysteresis. The stability results show that the device on c‐TiO₂/a‐SnO₂ retains about 91% of its initial PCE value after 500 h light illumination, which is higher than pure c‐TiO₂ (67%) based devices. Interestingly, using a‐SnO₂/c‐TiO₂ ETL the PCE loss was only 10% of initial value under continuous UV light illumination after 30 h, which is higher than that of c‐TiO₂ based device (28% PCE loss).     

Bacteriochlorophyll c monomers,dimers, and higher aggregates in dichloromethane,chloroform, and carbon tetrachloride

Bacteriochlorophyll c in vivo is a mixture of at least 5 homologs, all of which form aggregates in CH₂Cl₂, CHCl₃ and CCl₄. Three homologs exist mainly in the 2-R-(1-hydroxyethyl) configuration, whereas the other two homologs, 4-isobutyl-5-ethyl and 4-isobutyl-5-methyl farnesyl bacteriochlorophyll c, exist mainly in the 2-S-(1-hydroxyethyl) configuration (Smith KM, Craig GW, Kehres LA and Pfennig N (1983) J. Chromatograph. 281: 209–223). In CCl₄ the S-homologs form an aggregate of 2–3 molecules whose absorption (747 nm maximum) and circular dichroism spectra resemble those of the chlorosome. In CH₂Cl₂, CHCl₃ and CCl₄ the 4-n-propyl homolog (R-configuration) forms dimers absorbing at ca. 680 nm and higher aggregates absorbing at 705–710 nm. In CCl₄ the dimerization constant is approx. 10 µM^–1 (1000 times that for chlorophyll a). The difference between the types of aggregates formed by the 4-n-propyl and 4-isobutyl homologs is attributed to the difference between the R- and S-configurations of the 2-(1-hydroxyethyl) groups in each chlorophyll.Abbreviations BChl bacteriochlorophyll - CD circular dichroism - Chl chlorophyll - DNS data not shown - EEF 4-ethyl-5-ethyl farnesyl - iBM/EF 4-isobutyl-5-methyl/ethyl farnesyl - MEF 4-methyl-5-ethyl farnesyl - PEP 4-n-propyl-5-ethyl farnesyl     

Anaerobic degradation of tetrachloromethane by Acetobacterium woodii: separation of dechlorinative activities in cell extracts and roles for vitamin B12 and other factors

The transformations of ¹⁴CCl₄ by whole cells of Acetobacterium woodii suspended in phosphate buffer containing reducing agents, and by the cobalt corrinoid aquocobalamin in the same solution, were compared. Each catalyst transformed ¹⁴CCl₄ not only to reduced products (CHCl₃ and CH₂Cl₂) but also to CO and CO₂ as well as non-volatile products. The mass balance for radioactive carbon was complete in each case. Thus, the reactions of the pure cobalt corrinoid resemble the reactions in vivo. The proton in CHCl₃, formed from CCl₄ by A. woodii, was derived from water. Extracts of A. woodii were fractionated into large and small molecules, and each of the two fractions was separated chromatographically. Fractions of proteins demonstrated poor correlation between content of the corrinoid vitamin B₁₂ and rates of transformation of CCl₄. The correlation was somewhat improved if the fractions were autoclaved, but dechlorination in the absence of vitamin B₁₂ was observed. Separation of the small molecules yielded only one fraction containing vitamin B₁₂, and this fraction catalyzed dechlorination, whereas several other fractions were able to dechlorinate CCl₄ in the absence of vitamin B₁₂. We presume there to be unrecognized dechlorinative factors in anaerobic bacteria.Abbreviations GC gas chromatograph(y) - GC-MS (or-TCD or-FID) GC coupled to a mass spectrometer (or a thermal conductivity detector or a flame ionization detector) - HPLC high pressure liquid chromatograph(y) - FPLC high pressure protein chromatograph(y)     

Respiratory-cardiovascular physiology and chloroethane gill flux in the channel catfish, Ictalurus punctatus

A fish respirometer-metabolism chamber was used to obtain in vivo respiratory-cardiovascular and chloroethane gill flux data on transected channel catfish (Ictalurus punctatus). Methods used for spinal transection, attachment of an oral membrane (respiratory mast), placement and attachment of blood cannulas and urine catheters are described. Respiratory physiology, cardiac output and chemical extraction efficiencies for 1,1,2,2-tetrachloroethane (TCE), pentachloroethane (PCE), and hexachloroethane (HCE) were determined on 419–990 g catfish. The overall mean values (± s.d.) for ventilation volume (Q_v), effective respiratory volume (Q_w), oxygen consumption (Vo₂ and percentage utilization of oxygen (U) were 17-3 ±4–71 h^?1 kg^?1, 9·8±l·71 h^?1 kg^?1, 71·6±12·5mg h^?1 kg^?1, and 49± 10%, respectively, while cardiac output calculated via the Fick Method was 2·4±0·61 h^?1 kg^?1. Additional measurements were made on ventilation rate (V_r), total plasma protein, haematocrit (Hct), and urine volume; while both arterial and venous blood were analysed for pH, oxygen partial pressure (P02), carbon dioxide partial pressure (Pco₂), total oxygen (To₂), total carbon dioxide (Tco₂) and total ammonia (TAMM). Physiological measurements taken at 24 h were not significantly different from those taken at 48 h and indicated no deterioration of the in vivo preparation. All of these values agreed well with literature values on UTitransected channel catfish, except for Hct which was lower for cannulated animals used in this study. Overall, these data provide strong support for the use of transected channel catfish for in vivo collection of physiological and chemical gill flux data. The mean initial chemical extraction efficiencies for TCE, PCE and HCE were 41, 61 and 73%, respectively. Chemical clearances (Cl_X) for these same three chemicals were 5·9, 9·3 and 10·8 1 h^?1 kg^?1, respectively. The approximate 1: 1 relationship between effective respiratory volume (Q_w) and chemical clearance (Cl_x) indicated that branchial uptake of PCE and HCE was water flow-limited. Chemical gill flux observed for channel catfish and chloroethanes was similar to that observed for rainbow trout in previous studies and provided further support for the flow-limited model of chemical flux across fish gills.     

Isopropanol enhancement of carbon tetrachloride metabolism in vivo

We examined the effects of isopropanol (ISOP) pretreatment on the metabolism of ¹⁴CCl₄ to ¹⁴CO₂ and CHCl₃ exhaled in the breath, to ¹⁴C metabolite excreted in 24 hr urine and feces from 0 to 24 hr, and to ¹⁴C metabolite bound to liver at 24 hr. Fasted male rats were given 0.1 or 2.0 mmoles ¹⁴CCl₄/kg. ISOP pretreatment, which markedly enhanced the hepatotoxicity of CCl₄, selectively enhanced the rate and total extent of ¹⁴CO₂ and CHCl₃ metabolite exhalation. The pathways of CCl₄ metabolism leading to CO₂ and CHCl₃ metabolite formation may be more relevant to the hepatotoxicity of CCl₄ than the pathways leading to urinarym fecal or covalently bound metabolites.     

Evaluation of different culture conditions ofClostridium bifermentans DPH-1 for cost effective PCE degradation

Clostridium bifermentans strain DPH-1 has already been found to dechlorinate perchloroethylene (PCE) tocis-dichloroethylene (cis-DCE)via trichloroethylene (TCE). In this study, our investigation on different culture conditions of this DPH-1 strain was extended to find a more efficient and cost effective growth medium composition for this DPH-1 strain in bioremediation practices. Temperature dependency of strain DPH-1 showed that the growth starting time and PCE degradation at 15°C was very slow compared to that of 30°C, but complete PCE degradation occurred in both cases. For the proper utilization of strain DPH-1 in more cost effective bioremediation practices, a simpler composition of an effective media was studied. One component of the culture medium, yeast extract, had been substituted by molasses, which served as a good source of electron donor. The DPH-1 strain in the medium containing molasses, in the presence of K₂HPO₄ and KH₂PO₄, showed identical bacterial multiplication (0.135 mg protein mL⁻¹h⁻¹) and PCE degradation rates (0.38 μM/h) to those of the yeast extract containing medium.     

Protective effects of ascorbic acid on hepatotoxicity and oxidative stress caused by carbon tetrachloride in the liver of Wistar rats

This study was planned to investigate the protective effect of l (+)‐ascorbic acid (Vit C) on CCl₄‐induced hepatotoxicity and oxidative stress in the liver of Wistar rats (Rattus Norvegicus, strain Wistar). Twenty‐four adult male Wistar rats were fed with standard rat chow diet for 10 days and randomly were divided into four groups of six each as follows: (1) control, (2) CCl₄, (3) “CCl₄ + Vit C”, (4) Vit C groups. CCl₄ was applied to rats belonging to CCl₄ and “CCl₄ + Vit C” groups subcutaneously at 1 mg kg^?1 dose CCl₄ for 3 days. Vit C applied to “CCl₄ + Vit C” and “Vit C” group rats intraperitoneally at 300 mg kg^?1 dose for 3 days. All rats were sacrificed and livers were quickly removed on the fourth day of the experiment. MDA, total glutathione (T.GSH) levels and superoxide dismutase (SOD), catalase (CAT), glutathione peroxidase (GSH‐PX) activities were measured in the liver of all groups of rats and also serum alanine amino transferase (ALT) and aspartate amino transferase (AST) activities were detected to determine liver functions in all groups of rats. Histopathological changes were evaluated by light and transmission electron microscopes. In “CCl₄ + Vit C” group, MDA level was significantly decreased (p < 0.05) and SOD, CAT, GSH‐PX activities were significantly increased (p < 0.005, 0.01, 0.05) respectively, T.GSH level was significantly increased (p < 0.005) and serum ALT and AST activities were significantly decreased (p < 0.01, 0.05), respectively, when compared with CCl₄ group. These results show that Vit C has a highly protective effect on hepatotoxicity and oxidative stress caused by CCl₄. Copyright © 2009 John Wiley & Sons, Ltd.     

Accurate Determination of the Minimum HOMO Offset for Efficient Charge Generation using Organic Semiconducting Alloys

Current research indicates that exciton dissociation into free charge carriers can be achieved in material combinations with the highest occupied molecular orbital (HOMO) offset lowered to 0 eV in non‐fullerene organic solar cells. However, the quantitative relationship between the HOMO offset and exciton dissociation has not been established because of the difficulty in achieving continuously tunable HOMO offsets. Here, the binary blends of PTQ10:ZITI‐S and PTQ10:ZITI‐N are combined to form the positive and negative HOMO offsets of 0.20 and ?0.07 eV, respectively. While the PTQ10:ZITI‐S binary blend delivers a decent power conversion efficiency (PCE) of 10.69% with a short‐circuit current (J_sc) of 16.94 mA cm^?2, the PTQ10:ZITI‐N with the negative offset shows a much lower PCE of 7.06% mainly because of the low J_sc of 12.03 mA cm^?2. Because the tunable HOMO levels can be realized in organic semiconducting alloys based on ZITI‐N and ZITI‐S acceptors, the transformation of the HOMO energy offset from negative to positive values is achieved in the PTQ10:ZITIN:ZITI‐S ternary blends, delivering much‐improved PCEs up to 13.26% with a significant, 74% enhancement of J_sc to 20.93 mA cm^?2. With detailed investigations, the study reveals that the minimum HOMO offset of ≈40 meV is required to achieve the most‐efficient exciton dissociation and photovoltaic performance.     

The conformational properties of α,β‐dehydroamino acids with a C‐terminal ester group

α,β‐Dehydroamino acid esters occur in nature. To investigate their conformational properties, a systematic theoretical analysis was performed on the model molecules Ac‐ΔXaa‐OMe [ΔXaa = ΔAla, (E)‐ΔAbu, (Z)‐ΔAbu, ΔVal] at the B3LYP/6‐311+ + G(d,p) level in the gas phase as well as in chloroform and water solutions with the self‐consistent reaction field‐polarisable continuum model method. The Fourier transform IR spectra in CCl₄ and CHCl₃ have been analysed as well as the analogous solid state conformations drawn from The Cambridge Structural Database. The ΔAla residue has a considerable tendency to adopt planar conformations C5 (?, ψ ≈ ? 180°, 180°) and β2 (?, ψ ≈ ? 180°, 0°), regardless of the environment. The ΔVal residue prefers the conformation β2 (?, ψ ≈ ? 120°, 0°) in a low polar environment, but the conformations α (?, ψ ≈ ? 55°, 35°) and β (?, ψ ≈ ? 55°, 145°) when the polarity increases. The ΔAbu residues reveal intermediate properties, but their conformational dispositions depend on configuration of the side chain of residue: (E)‐ΔAbu is similar to ΔAla, whereas (Z)‐ΔAbu to ΔVal. Results indicate that the low‐energy conformation β2 is the characteristic feature of dehydroamino acid esters. The studied molecules constitute conformational patterns for dehydroamino acid esters with various side chain substituents in either or both Z and E positions. Copyright © 2011 European Peptide Society and John Wiley & Sons, Ltd.     

Anticholinesterase activity of some major intermediates in carbacylamidophosphate synthesis: Preparation,spectral characterization and inhibitory potency determination

Carbacylamidophosphates with the general formula RC(O)NHP(O)R₁R₂ constitute organophosphorus compounds that are used as insecticides, pesticides and ureas inhibitors. In this work, we studied the inhibition potency of CCl₃C(O)NHP(O)Cl₂1, CHCl₂C(O)NHP(O)Cl₂2, CH₂ClC(O)NHP(O)Cl₂3 and CF₃C(O)NHP(O)Cl₂4, which are the major intermediates for carbacylamidophosphates synthesis towards human erythrocyte acetylcholinesterase (hAChe) activity using Ellman's modified kinetic method. Unexpectedly, it was observed that they were not only hydrolytically unstable but also inhibited hAChE in a similar manner to that produced by organophosphorus insecticides. Enzymatic data, bimolecular inhibition rate constants (k_i) and IC₅₀ values for inhibition of hAChE demonstrated that they are irreversible inhibitors and the inhibition potency of compound 2 (IC₅₀ = 88 μM) was the greatest in comparison with compounds 1, 3 and 4. Also the electropositivity of the phosphorus atom and the hydrophobicity of the compounds demonstrated that these two factors play an additional effect and different role in the inhibitory activity of these compounds. Hydrolytic stability of the compounds was determined by ³¹P NMR monitoring of the loss of the parent molecules with D₂O as a function of time. This study considers antiacetylcholinesterase activity according to the structural and the electronic aspects of compounds 1–4, according to IR, ¹H, ¹³C and ³¹P NMR spectral data.     

Induction of hydroxyl radical production in Trametes versicolor to degrade recalcitrant chlorinated hydrocarbons

Extracellular hydroxyl radical (OH) production via quinone redox cycling in Trametes versicolor, grown in a chemically defined medium, was investigated to degrade trichloroethylene (TCE), perchloroethylene (PCE), 1,2,4- and 1,3,5-trichlorobenzene (TCB). The activity of the enzymes catalyzing the quinone redox cycle, quinone reductase and laccase, as well as the rate of OH production, estimated as the formation of thiobarbituric acid reactive substances (TBARS) from 2-deoxyribose, increased rapidly during the first 2–3 days and then remained at relatively constant levels. Under quinone redox cycling conditions, TCE degradation was concomitant to TBARS production and chloride release, reaching a plateau after 6 h of incubation. Similar results were obtained in PCE, 1,2,4- and 1,3,5-TCB time course degradation experiments. The mole balance of chloride release and 1,2,4-TCB and TCE degraded suggests that these chemicals were almost completely dechlorinated. Experiments using [¹³C]-TCE confirmed unequivocal transformation of TCE to ¹³CO₂. These results are of particular interest because PCE and 1,3,5-TCB degradation in aerobic conditions has been rarely reported to date in bacterial or fungal systems.     

Functionalization of fullerene via the Bingel reaction with α-chlorocarbanions: an ONIOM approach

Two-layer ONIOM method at the ONIOM(B3LYP/6-31G(d):PM6) level of theory was applied to study the cycloaddition reaction of α-chlorocarbanions (CR₂Cl^─, where R is H, Cl, CH₃ CN, and NO₂) and fullerene. The results show that the reaction pathways depend on the electron withdrawing functional groups or the electron donating functional groups contained in the α-chlorocarbanions. The energy profile analysis reveals that functionalization of fullerene by CCl₃ ^─, C(CH₃)₂Cl^─, and CH₂Cl^─ is more favorable than by C(CN)₂Cl^─ and C(NO₂)₂Cl^─ in terms of the thermodynamic point of view.     

Improving Film Formation and Photovoltage of Highly Efficient Inverted‐Type Perovskite Solar Cells through the Incorporation of New Polymeric Hole Selective Layers

Two chemically tailored new conjugated copolymers, HSL1 and HSL2, were developed and applied as hole selective layers to improve the anode interface of fullerene/perovskite planar heterojunction solar cells. The introduction of polar functional groups on the polymer side chains increases the surface energy of the hole selective layers (HSLs), which promote better wetting with the perovskite films and lead to better films with full coverage and high crystallinity. The deep highest occupied molecular orbital levels of the HSLs align well with the valence band of the perovskite semiconductors, resulted in increase photovoltage. The high lying lowest unoccupied molecule orbital level provides sufficient electron blocking ability to prevent electrons from reaching the anode and reduces the interfacial trap‐assisted recombination at the poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate)/perovskite interface, resulting in a longer charge‐recombination lifetime and shorter charge‐extraction time. In the presence of the HSLs, high‐performance CH₃NH₃PbI _x Cl_{3? x} perovskite solar cells with a power conversion efficiency (PCE) of 16.6% (V _oc: 1.07 V) and CH₃NH₃Pb(I_0.3Br_0.7) _x Cl_{3? x} cells with a PCE of 10.3% (V _oc: 1.34 V) can be realized.     

Effects of copper on expression of methane monooxygenases,trichloroethylene degradation,and community structure in methanotrophic consortia

Copper plays a key role in regulating the expression of enzymes that promote biodegradation of contaminants in methanotrophic consortia (MC). Here, we utilized MC isolated from landfill cover to investigate cometabolic degradation of trichloroethylene (TCE) at nine different copper (Cu²⁺) concentrations. The results demonstrated that an increase in Cu²⁺ concentration from 0 to 15 μM altered the specific first‐order rate constant k_1,TCE, the expression levels of methane monooxygenase (pmoA and mmoX) genes, and the specific activity of soluble methane monooxygenase (sMMO). High efficiency TCE degradation (95%) and the expression levels of methane monooxygenase (MMO) were detected at a Cu²⁺ concentration of 0.03 μM. Notably, sMMO‐specific activity ranged from 74.41 nmol/(mg_cell h) in 15 μM Cu²⁺ to 654.99 nmol/(mg_cell h) in 0.03 μM Cu²⁺, which contrasts with cultures of pure methanotrophs in which sMMO activity is depressed at high Cu²⁺ concentrations, indicating a special regulatory role for Cu²⁺ in MC. The results of MiSeq pyrosequencing indicated that higher Cu²⁺ concentrations stimulated the growth of methanotrophic microorganisms in MC. These findings have important implications for the elucidation of copper‐mediated regulatory mechanisms in MC.     

Highly stable and Efficient Perovskite Solar Cells Based on FAMA‐Perovskite‐Cu:NiO Composites with 20.7% Efficiency and 80.5% Fill Factor

To solve critical issues related to device stability and performance of perovskite solar cells (PSCs), FA_0.026MA_0.974PbI_3?yCl_y‐Cu:NiO (formamidinium methylammonium (FAMA)‐perovskite‐Cu:NiO) and Al₂O₃/Cu:NiO composites are developed and utilized for fabrication of highly stable and efficient PSCs through fully‐ambient‐air processes. The FAMA‐perovskite‐Cu:NiO composite crystals prepared without using any antisolvents not only improve the perovskite film quality with large‐size crystals and less grain boundaries but also tailor optical and electronic properties and suppress charge recombination with reduction of trap density. A champion device based on the composites as light absorber and Al₂O₃/Cu:NiO interfacial layer between electron transport layer and active layer yields power conversion efficiency (PCE) of 20.67% with V_OC of 1.047 V, J_SC of 24.51 mA cm^?2, and fill factor of 80.54%. More importantly, such composite‐based PSCs without encapsulation show significant enhancement in long‐term air‐stability, thermal‐ and photostability with retaining 97% of PCE over 240 d under ambient conditions (25–30 °C, 45–55% humidity).     

A Novel Anion Doping for Stable CsPbI2Br Perovskite Solar Cells with an Efficiency of 15.56% and an Open Circuit Voltage of 1.30 V

The Cs‐based inorganic perovskite solar cells (PSCs), such as CsPbI₂Br, have made a striking breakthrough with power conversion efficiency (PCE) over 16% and potential to be used as top cells for tandem devices. Herein, I^? is partially replaced with the acetate anion (Ac^?) in the CsPbI₂Br framework, producing multiple benefits. The Ac^? doping can change the morphology, electronic properties, and band structure of the host CsPbI₂Br film. The obtained CsPbI_2?x Br(Ac)_x perovskite films present lower trap densities, longer carrier lifetimes, and fast charge transportation compared to the host CsPbI₂Br films. Interestingly, the CsPbI_2?x Br(Ac)_x PSCs exhibit a maximum PCE of 15.56% and an ultrahigh open circuit voltage (V_oc) of 1.30 V without sacrificing photocurrent. Notably, such a remarkable V_oc is among the highest values of the previously reported CsPbI₂Br PSCs, while the PCE far exceeds all of them. In addition, the obtained CsPbI_2?x Br(Ac)_x PSCs exhibit high reproducibility and good stability. The stable CsPbI_2?x Br(Ac)_x PSCs with high V_oc and PCE are desirable for tandem solar cell applications.     

SrTiO3/Al2O3‐Graphene Electron Transport Layer for Highly Stable and Efficient Composites‐Based Perovskite Solar Cells with 20.6% Efficiency

For practical use of perovskite solar cells (PSCs) the instability issues of devices, attributed to degradation of perovskite molecules by moisture, ions migration, and thermal‐ and light‐instability, have to be solved. Herein, highly efficient and stable PSCs based on perovskite/Ag‐reduced graphene oxide (Ag‐rGO) and mesoporous Al₂O₃/graphene (mp‐AG) composites are reported. The mp‐AG composite is conductive with one‐order of magnitude higher mobility than mp‐TiO₂ and used for electron transport layer (ETL). Compared to the mp‐TiO₂ ETL based cells, the champion device based on perovskite/Ag‐rGO and SrTiO₃/mp‐AG composites shows overall a best performance (i.e., V_OC = 1.057 V, J_SC = 25.75 mA cm^?2, fill factor (FF) = 75.63%, and power conversion efficiency (PCE) = 20.58%). More importantly, the champion device without encapsulation exhibits not only remarkable thermal‐ and photostability but also long‐term stability, retaining 97–99% of the initial values of photovoltaic parameters and sustaining ≈93% of initial PCE over 300 d under ambient conditions.     

Complete degradation of tetrachloroethene by combining anaerobic dechlorinating and aerobic methanotrophic enrichment cultures

 Degradation of tetrachloroethene (perchloroethylene, PCE) was investigated by combining the metabolic abilities of anaerobic bacteria, capable of reductive dechlorination of PCE, with those of aerobic methanotrophic bacteria, capable of co-metabolic degradation of the less-chlorinated ethenes formed by reductive dechlorination of PCE. Anaerobic communities reductively dechlorinating PCE, trichloroethene (TCE) and dichloroethenes were enriched from various sources. The maximum rates of dechlorination observed for various chloroethenes in these batch enrichments were: PCE to TCE (341 μmol l^-1 day^-1), TCE to cis-dichloroethene (159 μmol l^-1 day^-1), cis-dichloroethene to chloroethene (99 μmol l^-1 day^-1) and trans-dichloroethene to chloroethene (22 μmol l^-1 day^-1). A mixture of these enrichments was inoculated into an anoxic fixed-bed upflow column. In this column PCE was converted mainly into cis-1, 2-dichloroethene, small amounts of TCE and chloroethene, and chloride. Enrichments of aerobic methanotrophic bacteria were grown in an oxic fixed-bed downflow column. Less-chlorinated ethenes, formed in the anoxic column, were further metabolized in this oxic methanotrophic column. On the basis of analysis of chloride production and the disappearance of chlorinated ethenes it was demonstrated that complete degradation of PCE was possible by combining these two columns. Operation of the two-column system under various process conditions indicated that the sensitivity of the methanotrophic bacteria to chlorinated intermediates represented the bottle-neck in the sequential anoxic/oxic degradation process of PCE. Received: 24 October 1994 / Received revision: 20 January 1995 / Accepted: 23 January 1995     

Biochemical and molecular characterization of a tetrachloroethene dechlorinating Desulfitobacterium sp. strain Y51: a review

A strict anaerobic bacterium, Desulfitobacterium sp. strain Y51, is capable of very efficiently dechlorinating tetrachloroethene (PCE) via trichloroethene (TCE) to cis-1,2-dichloroethene (cis-DCE) at concentrations as high as 960 μM and as low as 0.06 μM. Dechlorination was highly susceptible to air oxidation and to potential alternative electron acceptors, such as nitrite, nitrate or sulfite. The PCE reductive dehalogenase (encoded by the pceA gene and abbreviated as PceA dehalogenase) of strain Y51 was purified and characterized. The purified enzyme catalyzed the reductive dechlorination of PCE to cis-DCE at a specific activity of 113.6 nmol min⁻¹  mg protein⁻¹ . The apparent K _m values for PCE and TCE were 105.7 and 535.3 μM, respectively. In addition to PCE and TCE, the enzyme exhibited dechlorination activity for various chlorinated ethanes such as hexachloroethane, pentachloroethane, 1,1,1,2-tetrachloroethane and 1,1,2,2-tetrachloroethane. An 8.4-kb DNA fragment cloned from the Y51 genome revealed eight open reading frames, including the pceAB genes. Immunoblot analysis revealed that PceA dehalogenase is localized in the periplasm of Y51 cells. Production of PceA dehalogenase was induced upon addition of TCE. Significant growth inhibition of strain Y51 was observed in the presence of cis-DCE, More interestingly, the pce gene cluster was deleted with high frequency when the cells were grown with cis-DCE.