Fed-batch fermentation for production of Kluyveromyces marxianusFII 510700 cultivated on a lactose-based medium

A strain of Kluyveromyces marxianus was grown in batch culture in lactose-based media at varying initial lactose concentrations (10–60 g L^–1) at 30°C, pH 5.0, dissolved oxygen concentrations greater than 20%. Increasing the concentration of mineral salts three-fold at 40 g L^–1 and 60 g L^–1 initial lactose concentration showed only a small increase in the yield of biomass, from 0.38 g g^–1 to 0.41 g g^–1, indicating that the initial batch cultures were not significantly nutrient- (mineral salts)-limited. A relatively high biomass concentration (105 g L^–1) was obtained in fed-batch culture following extended lactose feeding. An average specific growth rate (0.27 h^–1), biomass yield (0.38 g g^–1) and overall productivity (2.9 g L^–1 h^–1) were obtained for these fed-batch conditions. This fed-batch protocol provides a strategy for achieving relatively high concentrations and productivities of K. marxianus on other lactose-based substrate streams (e.g., whey) from the dairy industry.     

Biomass relationship to growth and phosphate uptake ofPseudomonas fluorescens,Escherichia coli andAcinetobacter radioresistens in mixed liquor medium

The ability ofPseudomonas fluorescens, Escherichia coli andAcinetobacter radioresistenns to remove phosphate during growth was related to the initial biomass as well as to growth stages and bacterial species. Phosphate was removed by these bacteria under favourable conditions as well as under unfavourable conditions of growth. Experiments showed a relationship between a high initial cell density and phosphate uptake. More phosphate was released than removed when low initial cell densities (10²–10⁵ cells ml^–1) were used. At a high initial biomass concentration (10⁸ cells ml^–1), phosphate was removed during the lag phase and during logarthmic growth byP. fluorescens. Escherichia coli. at high initial biomass concentrations (10⁷ cells ml^–1), accumulated most of the phosphate during the first hour of the lag phase and/or during logarithmic growth and in some cases removed a small quantily of phosphate during the stationary growth phase.Acinetobacter radioresistens, at high initial cell densities (10⁶, 10⁷ cells ml^–1) removed most of phosphate during the first hour of the lag phase and some phosphate during the stationary growth phase.Pseudomonas fluorescens removed phosphate more thanA. radioresistens andE. coli with specific average ranges from 3.00–28.50 mg L^–1 compared to average ranges of 4.92–17.14 mg L^–1 forA. radioresistens and to average ranges of 0.50–8.50 mg L^–1 forE. coli.     

Removal of heavy metals from industrial wastewater using microbial fuel cell

Removal efficiency of gold from a solution of pure tetrachloroaurate ions was investigated using microbial fuel cell (MFC) technology. The effects of type of catholyte solution and initial gold concentration on the removal efficiency were considered. Due to its presence at high levels in the gold wastewater, the effect of copper ions on the removal efficiency of the gold ions was also studied. The effects of pH and initial biomass concentration on the gold removal efficiency was also determined. The results showed that after 5 h contact time, 95% of gold removal efficiency from a wastewater containing 250 ppm of initial gold ions at ambient temperature using 80 g/L yeast concentration was achieved. After 48 h of the cell''s operation under the same condition, 98.86% of AuCl₄ ^– ions were successfully removed from the solution. At initial gold concentration in the waste solution of 250 ppm, pH 2, and initial yeast concentration of 80 g/L, 100% removal efficiency of the gold was achieved. On the other hand, the most suitable condition for copper removal was found at a pH of 5.2, where 53% removal efficiency from the waste solution was accomplished.     

Biosorption of inorganic and methyl mercury by a biosorbent from Aspergillus niger

A biosorbent prepared by alkaline extraction of Aspergillus niger biomass was evaluated for its potential to remove mercury species – inorganic (Hg²⁺) and methyl mercury (CH₃Hg⁺) – from aqueous solutions. Batch experiments were carried out to determine the pH and time profile of sorption for both species in the pH range 2–7. The Hg²⁺ exhibited more rapid sorption and higher capacity than the CH₃Hg⁺. Further, removal of both mercury species from spiked ground water samples was efficient and not influenced by other ions. Sorption studies with esterified biosorbent indicated loss of binding of both mercury species (>80%), which was regained when the ester groups were removed by alkaline hydrolysis, suggesting the involvement of carboxyl groups in binding. Further, no interconversion of sorbed species occurred on the biomass. The biosorbent was reusable up to six cycles without serious loss of binding capacity. Our results suggest that the biosorbent from Aspergillus niger can be used for removal of mercury and methyl mercury ions from polluted aqueous effluents.     

Assessment of the metal removal capability of two capsulated cyanobacteria, Cyanospira capsulata and Nostoc PCC7936

Two capsulated, exopolysaccharide-producing cyanobacteria, Cyanospira capsulata and Nostoc PCC7936, were tested with regard to their metal removal capability by using copper as model metal. The experiments, carried out with the sole cyanobacterial biomass suspended in distilled water and confined into small dialysis tubings, showed that C. capsulata biomass is characterized by the best efficiency in metal removal, with a q_max (maximum amount of copper removed per biomass unit) of 96 ± 2 mg Cu(II) removed per g of protein in comparison with the value of 79 ± 3 of Nostoc PCC7936 biomass. The experimental data obtained with both cyanobacterial biomass best fit the Langmuir sorption isotherm. The sorption of copper started from the first minutes of contact with the metal and attained the equilibrium state, when no more copper removal was evident, after 5 and 6 hours, for C. capsulata and Nostoc PCC7936, respectively. The best efficiency in Cu(II) removal was obtained at pH 6.1–6.2, while the presence of Mg²⁺ or Ca²⁺ reduced copper removal capability of both species to 60–70% of their q_max. The results showed that the biomass of C. capsulata and Nostoc PCC7936 possesses a high affinity and a high specific uptake for copper, comparable with the best performances shown by other microbial biomass, and suggest the possibility to use the capsulated trichomes of the two cyanobacteria for the bioremoval of heavy metals from polluted water bodies.     

Annual productivity of Spirulina (Arthrospira) and nutrient removal in a pig wastewater recycling process under tropical conditions

An evaluation was made of the annual productivity of Spirulina (Arthrospira) and its ability to remove nutrients in outdoor raceways treating anaerobic effluents from pig wastewater under tropical conditions. The study was based at a pilot plant at La Mancha beach, State of Veracruz, Mexico. Batch or semi-continuous cultures were established at different seasons during four consecutive years. The protein content of the harvested biomass and the N and P removal from the ponds were also evaluated. Anaerobic effluents from digested pig waste were added in a proportion of 2% (v/v) to untreated sea-water diluted 1:4 with fresh water supplemented with 2 g L^–1 sodium bicarbonate, at days 0, 3 and 5. A straight filament strain of Spirulina adapted to grow in this complex medium was utilized. A pH value 9.5 ± 0.2 was maintained. The productivity of batch cultures during summer 1998 was significantly more with a pond depth of 0.10 m than with a depth 0.065 m. The average productivity of semi-continuous cultures during summer 1999 was 14.4 g m^–2 d^–1 with a pond depth of 0.15 m and 15.1 g m^–2 d^–1 with a depth of 0.20 m. The average annual productivity for semi-continuous cultures operating with depths of 0.10 m for winter and 0.15 and 0.25 m for the rest of the year, was 11.8 g m^–2 d^–1. This is the highest value reported for a Spirulina cultivation system utilising sea-water. The average protein content of the semi-continuous cultures was 48.9% ash-free dry weight. NH₄-N removal was in the range 84–96% and P removal in the range of 72–87%, depending on the depth of the culture and the season.     

Production of docosahexaenoic acid byThraustochytrium roseum

Summary When threeThraustochytrium stains were cultivated in liquid media containing 2.5% starch and 0.2% yeast extract, initial pH 6.0, with shaking under fluorescent light for five days at 25°C, similar biomass yields were observed (9.7–10.3 g L^–1). Contents of docosahexaenoic acid (DHA) in biomass varied: 0.15, 3.55 and 6.40% w/w forT. striatum ATCC 24473,T. aureum ATCC 34304 andT. roseum ATCC 28210, respectively. In further studies,T. roseum produced a maximum titer of 0.85 g of DHA per liter of culture broth. The DHA content of total lipids ranged from 46–49% w/w.     

Utilisation of soil organic P by agroforestry and crop species in the field,western Kenya

A field experiment in western Kenya assessed whether the agroforestry species Tithonia diversifolia (Hemsley) A. Gray, Tephrosia vogelii Hook f., Crotalaria grahamiana Wight & Arn. and Sesbania sesban (L) Merill. had access to forms of soil P unavailable to maize, and the consequences of this for sustainable management of biomass transfer. The species were grown in rows at high planting density to ensure the soil under rows was thoroughly permeated by roots. Soil samples taken from beneath rows were compared to controls, which included a bulk soil monolith enclosed by iron sheets within the tithonia plot, continuous maize, and bare fallow plots. Three separate plant biomass samples and soil samples were taken at 6-month intervals, over a period of 18 months. The agroforestry species produced mainly leaf biomass in the first 6 months but stem growth dominated thereafter. Consequently, litterfall was greatest early in the experiment (0–6 months) and declined with continued growth. Soil pH increased by up to 1 unit (from pH 4.85) and available P increased by up to 38% (1 g P g^–1) in agroforestry plots where biomass was conserved on the field. In contrast, in plots where biomass was removed, P availability decreased by up to 15%. Coincident with the declines in litterfall, pH decreased by up to 0.26 pH units, plant available P decreased by between 0.27 and 0.72 g g^–1 and P_o concentration decreased by between 8 and 35 g g^–1 in the agroforestry plots. Declines in P_o were related to phosphatase activity (R²=0.65, P<0.05), which was greater under agroforestry species (0.40–0.50 nmol MUB s^–1 g^–1) than maize (0.28 nmol MUB s^–1 g^–1) or the bare fallow (0.25 nmol MUB s^–1 g^–1). Management of tithonia for biomass transfer, decreased available soil P by 0.70 g g^–1 and P_o by 22.82 g g^–1. In this study, tithonia acquired P_o that was unavailable to maize. However, it is apparent that continuous cutting and removal of biomass would lead to rapid depletion of P stored in organic forms.     

Removal of chromium(VI) and cadmium(II) from aqueous solution by a bacterial biofilm supported on granular activated carbon

A biofilm of Arthrobacter viscosus, supported on granular activated carbon, removed between 100% and 50% of Cr(VI) and between 100% and 20% of Cd(II) from solutions with initial concentrations between 4–11 mg_metal l^–1 and a flow residence time of 1.2 min. For experiments of lower initial concentrations, a steady-state removal of 50% was reached after 71 bed volumes of Cr solution passed through the biosorbent bed and a steady-state removal of 30% was reached after 47 bed volumes of Cd solution passed through a similar bed. Final uptakes of 8.5 mg_Cr g_carbon ^–1 and 4.2 mg_cd g_carbon ^–1 were determined for initial concentrations of 10 mg_Cr l^–1 and 11 mg_Cd l^–1, respectively. The influence on the overall process of two different surface treatments of the support was evaluated and compared with the behavior of a support not treated.     

Removal of Cr(VI) from ground water by Saccharomyces cerevisiae

Chromium can be removed from ground water by the unicellular yeast, Saccharomyces cerevisiae. Local ground water maintains chromium as CrO₄ ^2- because of bicarbonate buffering and pH and E _h conditions (8.2 and +343 mV, respectively). In laboratory studies, we used commercially available, nonpathogenic S. cerevisiae to remove hexavalent chromium [Cr(VI)] from ground water. The influence of parameters such as temperature, pH, and glucose concentration on Cr(VI) removal by yeast were also examined. S. cerevisiae removed Cr(VI) under aerobic and anaerobic conditions, with a slightly greater rate occurring under anaerobic conditions. Our kinetic studies reveal a reaction rate (V_max) of 0.227 mg h^-1 (g dry wt biomass)^-1 and a Michaelis constant (Km) of 145 mg/l in natural ground water using mature S. cerevisiae cultures. We found a rapid (within 2 minutes) initial removal of Cr(VI) with freshly hydrated cells [55–67 mg h^-1 (g dry wt biomass)^-1] followed by a much slower uptake [0.6–1.1 mg h^-1 (g dry wt biomass)^-1] that diminished with time. A materials-balance for a batch reactor over 24 hours resulted in an overall shift in redox potential from +321 to +90 mV, an increase in the bicarbonate concentration (150–3400 mg/l) and a decrease in the Cr(VI) concentration in the effluent (1.9-0 mg/l).     

Biosorption of di(2-ethylhexyl)phthalate by seaweed biomass

Samples of various Sargassum species were collected in the Hong Kong marine environment and used for studies on biosorption of di(2-ethylhexyl)phthalate (DEHP). Batch adsorption experiments were carried out to determine the removal capacity and removal efficiency of the biosorbents. The DEHP removal ability was similar among beached seaweed and three freshly collected Sargassum species. Different physico-chemical factors were evaluated in order to enhance the performance of the biosorbents. Under optimized conditions (25 mg biomass, initial pH 4, 25 °C, 40 mg L^–1 DEHP), the mean removal capacity of beached seaweed and Sargassum siliquastrum was 5.68 and 6.54 mg g^–1, respectively. Examination of the Langmuir and Freundlich adsorption isotherms showed that the biosorption phenomenon by these biosorbents could well be described by these models. Desorption of DEHP was also assessed with methanol, which showed the most satisfactory desorbing ability. Further study in multiple adsorption–desorption of DEHP by the biosorbents demonstrated the reusability of both beached seaweed and S. siliquastrum for biosorption of DEHP.     

Ecological problems of Lake Ladoga: causes and solutions

We studied the outcome of competition between a large (Brachionus calyciflorus) and a small (Anuraeopsis fissa) rotifer species at five algal (Scenedesmus acutus) concentrations (0.5 × 10⁶ to 40.5 × 10⁶ cells ml^–1) and with varying initial densities in mixed populations (100 to 0% of B. calcyciflorus or A. fissa), the combined initial biomass being 0.2 µg ml^–1 in all test jars. Experiments were conducted at 28 ± 1 °C.Regardless of food concentration, B. calcyciflorus showed a greater increase in biomass than A. fissa, peak densities (mean ± standard error) at the lowest food concentration in the controls being 1.34 ± 0.31 µg dry weight ml^–1 and 0.82 ± 0.08 dry weight ml^–1, respectively. At the lower food concentrations, A. fissa displaced B. calyciflorus and vice versa at the higher food concentrations. At the intermediate food concentrations of 4.5 × 10⁶ cells ml^–1, B. calyciflorus outcompeted A. fissa only if its initial population density was three times higher. The rates of population growth in controls varied from 0.792 ± 0.06 d^–1 to 1.492 ± 0.13 d^–1 for B. calyciflorus and 0.445 ± 0.04 to 0.885 ± 0.01 for A. fissa depending on food level. When both species were introduced together, low food levels favoured higher abundance of A. fissa than B. calyciflorus, suggesting, in nature, it is likely that small Anuraeopsis colonize oligotrophic water bodies more successfully than larger Brachionus. The results also suggest that the outcome of competition depends not only on the size of the competing species and food availability but also on their colonizing density.     

L-Sorbose production in a continuous fermenter with and without cell recycle

The kinetics of continuous l-sorbose fermentation using Acetobacter suboxydans with and without cell recycle (100%) were investigated at dilution rates (D) of 0.05, 0.10, 0.15 and 0.3 h^–1. The biomass and sorbose concentrations for continuous fermentation without recycle increased as the dilution rate was increased from 0.05 to 0.10 h^–1. A maximum biomass concentration of 8.44 g l^–1 and sorbose concentration of 176.90 g l^–1 were obtained at D=0.10 h^–1. The specific rate of sorbose production and volumetric sorbose productivity at this dilution rate were 2.09 g g^–1 h^–1 and 17.69 g l^–1 h^–1. However, on further increasing the dilution rate to 0.3 h^–1, both biomass and sorbose concentrations decreased to 2.93 and 73.20 g l^–1 respectively, mainly due to washout of the reactor contents. However, the specific rate of sorbose formation and volumetric sorbose productivity at this dilution rate increased to 7.49 g g^–1 h^–1 and 21.96 g l^–1 h^–1 respectively. Continuous fermentation with 100% cell recycle served to further enhance the concentration of biomass and sorbose to 28.27 and 184.32 g l^–1 respectively (in the reactor at a dilution rate of 0.05 h^–1). Even though, there was a decline in the biomass and sorbose concentrations to 6.8 and 83.40 g l^–1 at a dilution rate of 0.3 h^–1, the specific rates of sorbose formation and volumetric sorbose productivity increased to 3.67 g g^–1h^–1 and 25.02 g l^–1 h^–1.     

Filamentous algae in fish ponds of the Třeboň Biosphere Reserve-ecophysiological study

Filamentous algae in eutrophic carp ponds in South Bohemia (Central Europe) were studied from 1988 to 1990. High biomass (490 g DW m^-2) was attained by Cladophora fracta (O. F. Müll. ex Vahl) Kütz. after two months of growth. This marked growth depleted inorganic carbon in the water, but did not decrease the concentration of tissue nutrients. Laboratory measurements of final pH indicate that all the filamentous algae studied, except for Tribonema, are very efficient HCO₃ ^- users. An extremely high pH of 11.6 and oxygen concentration of 32 mg l^-1 were measured in the algal mats. High pH resulted in CaCO₃ precipitation, visible as white incrustations on algal filaments. The amount of precipitated CaCO₃ reached 134 kg ha^-1. After reaching peak biomass, 90% of the Cladophora decomposed over the next 95 days.The highest net photosynthetic rate in C. fracta was measured between pH range 8.5–10.0 and oxygen concentrations of 7–12 mg l^-1. Optimum temperature for photosynthesis was between 17–22°C.     

Life cycle and growth ofTrichostegia minor (Curtis) in temporary woodland pools (Trichoptera: Phryganeidae)

Larvae of the caddisTrichostegia minor (Curtis) were collected from four woodland pools in The Netherlands, three of which are temporary, from August 1986 till June 1987. Eggs and larvae of this species proved to be very well adapted to drought, freezing, strongly fluctuating pH and alkalinity levels and prolonged oxygen deficit. The life cycle ofT.minor in a small woodland marsh overgrown byCalla palustris took one year. Adult flight period started at the end of May. Oviposition took place independent of water. Hatching of the eggs started in September and was probably induced by immersion. During the larval stage from September until May, 5 instars could be distinguished by the size of the head capsule. Growth of instars I, II and III during autumn was moderate. Most larvae overwintered as instar III or IV. Possibly there was a larval diapause during winter. In spring rapid growth to instar V took place prior to pupation. Growth rate, expressed as the increase of mean individual dry weight was highest from March to April (2.05±0.75% DW.m^–2.d^–1). In extremely shallow water growth in spring was initially more rapid compared to growth in deeper water. During winter the growth rate decreased to 0.038±0.071% DW.m^–2.d^–1. Net annual production based on the changes of momentary biomass was 183.2±31.7 mg DW.m^–2.y^–1 or 177.2±31.3 mg AFDW.m^–2.y^–1. Production loss during the winter season was 75.1±10.8 mg DW.m^–2.y^–1 or 72.3±10.6 mg AFDW.m^–2.y^–1.     

Potential of Salix as phytoextractor for Cd on moderately contaminated soils

Biomass production and Cd uptake in Salix (willow) is generally high. The aim of this study was to quantify the amounts of Cd in different plant and soil compartments in commercial Salix stands grown on different soil types and to use these data for estimation of the long-term effects of Cd removal by Salix at stem harvest on the soil Cd content by calculating Cd balances. Ten commercial short rotation willow coppice stands, planted with clone 78183 of Salix viminalis (L.) were investigated in order to include three different soil types with respect to pH. Stands with high stem biomass production generally had lower Cd concentrations in the plant and grew on more alkaline soils with low Cd availability when compared to stands with low stem biomass production. The highest output of Cd by Salix is therefore not necessarily achieved by stands with the highest yields or the highest Cd concentrations, as both these parameters have to be considered. The net removal of Cd from the plough layer by the Salix crop under different conditions varied between 2.6 and 16.5 g Cd ha^–1 year^–1. The long-term effects of Salix cultivation on soil Cd content, i.e. after 6–7 cutting cycles (25 years), were calculated and we reached the conclusion that there is a high potential in Salix to remove significant amounts of Cd at stem harvest. Salix can therefore presumably be used to counteract Cd pollution of agricultural soils in Sweden provided that the Cd in furnace ashes is taken care of.     

Growth inhibition by ammonia and use of a pH-controlled feeding strategy for the effective cultivation of Mycobacterium chlorophenolicum

The inhibitory effect of ammonia on the growth of the polychlorinated xenobiotic-degrading bacterium Mycobacterium chlorophenolicum was examined. The strain is inhibited by both the ionized and nonionized forms of ammonia. At pH 6.9 50% reduction of the growth rate was observed at 6.8 g l^–1 total ammonium. For 23 experiments performed in shake-flask culture at different pH values and ammonium concentrations a growth model based on the extended Monod kinetic fits the data with a deviation of 5.3%. To overcome growth inhibition in bioreactors a pH-controlled feeding strategy was developed for effective cultivation of M. chlorophenolicum at an ammonium level below 0.3 g l^–1. The ammonium addition was controlled on-line by the stoichiometric interdependence of ammonium consumption and pH decline. With this on-line control strategy a biomass concentration as high as 26.2 g l^–1 can be achieved within less than 1 week of cultivation, compared to a biomass concentration of 15.5 g l^–1 in normal batch culture after 2 weeks of cultivation. The yield is also increased from 0.32 g to 0.43 g biomass (g glucose)^–1. The strategy developed provides an effective method for the production of biomass of M. chlorophenolicum serving as the inoculum in remediation technologies.     

Biosorption of reactive dyes by the mycelium pellets of a new isolate of Penicillium oxalicum

Three reactive dyes were rapidly adsorbed by the mycelium pellets of Penicillium oxalicum. Dye removal of Reactive Blue 19 was up to 60% in 10 min and 91% in 80 min. Dye adsorption isotherms fitted Langmuir model well and the maximum adsorption capacities at 20 °C were calculated to be 160 mg g^–1 for Reactive Blue 19, 122 mg g^–1 for Reactive Red 241 and 137 mg g^–1 for Reactive Yellow 145, respectively. The pellets exhibited a high dye adsorption capacity (80–180 mg g^–1) for all of the 3 dyes over a wide pH range (pH 2–10), and the maximum adsorption was obtained at pH 2. The adsorption capacity was mildly increased by increasing salinity.     

A novel thermotolerant methylotrophicBacillus sp. and its potential for use in single-cell protein production

A thermotolerant methylotrophicBacillus sp. (KISRI TM1A, NCIMB 40040), isolated from the Kuwaiti environment and belonging to the group II spore-forming, bacilli, could not be correlated with any knownBacillus sp. It may, therefore, be a new species. It grew at temperatures from 37° to 58°C from pH 6.5 to 9.0 and on methanol up to 40 g l^–1. It grew well in a chemostat. Its biomass yield coefficient was improved by about 30% by optimization of medium and growth conditions, reaching a maximum of 0.44g g^–1 at 45°C pH 6.8 to 7.0, dilution rate 0.25 h^–1 with methanol at 10 g l^–1. Average crude protein and amino acid content were 84% and 60%, respectively, and maximum productivity attained under laboratory conditions was 5.06 g l^–1h^–1. It was concluded that this strain has good potential for use in single-cell protein production.     

Phytase production by the yeast, Pichia anomala

Pichia anomala, isolated from dried flower buds of Woodfordia fruticosa, produced a high activity of an intracellular phytase, at 68 U per g dry biomass, when grown at 20 °C for 24 h in a medium containing glucose (40 g l^–1) and beef extract (10 g l^–1) supplemented with Fe²⁺ (0.15 mM). Partially purified phytase was optimally active at 60 °C and pH 4 with a half life of 7 days at 60 °C. It retained 85% of its activity at 80 °C for 15 min. The enzyme is suitable for supplementing animal feeds to improve the availability of phosphate from phytate.