Ethanol production from hydrolysed agricultural wastes using mixed culture of <Emphasis Type="Italic">Zymomonas mobilis</Emphasis> and <Emphasis Type="Italic">Candida tropicalis</Emphasis>

Acid, alkaline and enzymatic hydrolysis of agricultural crop wastes were compared for yields of total reducing sugars with the hydrolysates being evaluated for ethanol production using a mixed culture of Zymomonas mobilis and Candida tropicalis. Acid hydrolysis of fruit and vegetable residues gave 49–84 g reducing sugars l⁻¹ and 29–32 g ethanol l⁻¹ was then obtained. Alkaline hydrolysis did not give significant amount of reducing sugars. Enzymatic hydrolysis of fruit and vegetable residues yielded 36–123 g reducing sugars l⁻¹ and 11–54 g ethanol l⁻¹.     

Optimization of culture conditions and scale-up to pilot and plant scales for coenzyme Q<Subscript>10</Subscript> production by <Emphasis Type="Italic">Agrobacterium tumefaciens</Emphasis>

This report describes the optimization of culture conditions for coenzyme Q₁₀ (CoQ₁₀) production by Agrobacterium tumefaciens KCCM 10413, an identified high-CoQ₁₀-producing strain (Kim et al., Korean patent. 10-0458818, 2002b). Among the conditions tested, the pH and the dissolved oxygen (DO) levels were the key factors affecting CoQ₁₀ production. When the pH and DO levels were controlled at 7.0 and 0–10%, respectively, a dry cell weight (DCW) of 48.4 g l⁻¹ and a CoQ₁₀ production of 320 mg l⁻¹ were obtained after 96 h of batch culture, corresponding to a specific CoQ₁₀ content of 6.61 mg g-DCW⁻¹. In a fed-batch culture of sucrose, the DCW, specific CoQ₁₀ content, and CoQ₁₀ production increased to 53.6 g l⁻¹, 8.54 mg g-DCW⁻¹, and 458 mg l⁻¹, respectively. CoQ₁₀ production was scaled up from a laboratory scale (5-l fermentor) to a pilot scale (300 l) and a plant scale (5,000 l) using the impeller tip velocity (V _tip) as a scale-up parameter. CoQ₁₀ production at the laboratory scale was similar to those at the pilot and plant scales. This is the first report of pilot- and plant-scale productions of CoQ₁₀ in A. tumefaciens.     

Continuous ethanol production from wheat straw hydrolysate by recombinant ethanologenic <Emphasis Type="BoldItalic">Escherichia coli</Emphasis> strain FBR5

Continuous production of ethanol from alkaline peroxide pretreated and enzymatically saccharified wheat straw hydrolysate by ethanologenic recombinant Escherichia coli strain FBR5 was investigated under various conditions at controlled pH 6.5 and 35°C. The strain FBR5 was chosen because of its ability to ferment both hexose and pentose sugars under semi-anaerobic conditions without using antibiotics. The average ethanol produced from the available sugars (21.9–47.8 g/L) ranged from 8.8 to 17.3 g/L (0.28–0.45 g/g available sugars, 0.31–0.48 g/g sugar consumed) with ethanol productivity of 0.27–0.78 g l⁻¹ h⁻¹ in a set of 14 continuous culture (CC) runs (16–105 days). During these CC runs, no loss of ethanol productivity was observed. This is the first report on the continuous production of ethanol by the recombinant bacterium from a lignocellulosic hydrolysate.     

Very high ethanol productivity in an innovative continuous two-stage bioreactor with cell recycle

The performance of an innovative two-stage continuous bioreactor with cell recycle—potentially capable of giving very high ethanol productivity—was investigated. The first stage was dedicated to cell growth, whereas the second stage was dedicated to ethanol production. A high cell density was obtained by an ultrafiltration module coupled to the outlet of the second reactor. A recycle loop from the second stage to the first one was tested to improve cell viability and activity. Cultivations of Saccharomyces cerevisiae in mineral medium on glucose were performed at 30°C and pH 4. At steady state, total biomass concentrations of 59 and 157 gDCW l⁻¹ and ethanol concentrations of 31 and 65 g l⁻¹ were obtained in the first and second stage, respectively. The residual glucose concentration was 73 g l⁻¹ in the first stage and close to zero in the second stage. The present study shows that a very high ethanol productivity (up to 41 g l⁻¹ h⁻¹) can indeed be obtained with complete conversion of the glucose and with a high ethanol titre (8.3°GL) in the two-stage system.     

Optimization of polyhydroxybutyrate production by <Emphasis Type="Italic">Bacillus</Emphasis> sp. CFR 256 with corn steep liquor as a nitrogen source

Polyhydroxyalkanotes (PHAs), the eco-friendly biopolymers produced by many bacteria, are gaining importance in curtailing the environmental pollution by replacing the non-biodegradable plastics derived from petroleum. The present study was carried out to economize the polyhydroxybutyrate (PHB) production by optimizing the fermentation medium using corn steep liquor (CSL), a by-product of starch processing industry, as a cheap nitrogen source, by Bacillus sp. CFR 256. Response surface methodology (RSM) was used to optimize the fermentation medium using the variables such as corn steep liquor (5–25 g l⁻¹), Na₂HPO₄ 2H₂O (2.2–6.2 g l⁻¹), KH₂PO₄ (0.5–2.5 g l⁻¹), sucrose (5–55 g l⁻¹) and inoculum concentration (1–25 ml l⁻¹). Central composite rotatable design (CCRD) experiments were carried out to study the complex interactions of the variables. The optimum conditions for maximum PHB production were (g l⁻¹): CSL-25, Na₂HPO₄ 2H₂O-2.2, KH₂PO₄ − 0.5, sucrose − 55 and inoculum − 10 (ml l⁻¹). After 72 h of fermentation, the amount of PHA produced was 8.20 g l⁻¹ (51.20% of dry cell biomass). It is the first report on optimization of fermentation medium using CSL as a nitrogen source, for PHB production by Bacillus sp.     

Optimization of nutrient components for enhanced phenazine-1-carboxylic acid production by <Emphasis Type="Italic">gacA</Emphasis>-inactivated <Emphasis Type="Italic">Pseudomonas</Emphasis> sp. M18G using response surface method

The nutritional requirements for phenazine-1-carboxylic acid (PCA) production using Pseudomonas sp. M18G, a gacA chromosomal-inactivated mutant of the strain M18, with a high PCA yield, were optimized statistically in shake flask experiments. Based on a single-factor experiment design, we implemented the two-level Plackett–Burman (PB) design with 11 variables to screen medium components that significantly influence PCA production. Soybean meal, glucose, soy peptone, and ethanol were identified as the most important significant factors (P < 0.05). Response surface methodology based on the Center Composite Design (CCD) was applied to determine these factors’ optimal levels and their mutual interactions between components for PCA production. The predicted results showed that 1.89 g l⁻¹ of PCA production was obtained after a 60-h fermentation period, with optimal concentrations of soybean meal powder (33.4 g l⁻¹), glucose (12.7 g l⁻¹), soy peptone (10.9 g l⁻¹), and ethanol (13.8 ml l⁻¹) in the flask fermentations. The validity of the model developed was verified, and the optimum medium led to a maximum PCA concentration of 2.0 g l⁻¹, a nearly threefold increase compared to that in the basal medium. Furthermore, the experiment was scaled up in the 10 l fermentor and 2 g l⁻¹ PCA productions were achieved in 48 h based on optimization mediums which further verified the practicability of this optimum strategy.     

High Frequency Plant Regeneration from Callus Culture of Pleione formosana Hayata

High frequency plant regeneration was induced from protocorm-derived callus cultured on half-strength of Murashige—Skoog medium with 2,4-dichlorophenoxyacetic acid (2,4-D, 0–5 mg l⁻¹) and 1-phenyl-3-(1,2,3-thiadiazol-5-yl, 0–1 mg l⁻¹) urea (TDZ) in the dark. Twelve totipotent callus lines were selected within 76 callus lines regenerated on half-strength of Murashige—Skoog (MS) medium with 0.5 mg l⁻¹ TDZ. The proliferation rate was 4–5-fold in fresh weight after 30 days of culture on half-strength MS medium containing 5 mg l⁻¹ 2,4-D and 0.5 mg l⁻¹ TDZ in the dark. The maximum number of shoot buds generated by 0.01 g callus explant was 134 after 4 months of culture. These calli were regenerated to plantlets via protocorm-like bodies (PLBs) after 75–150 days of culture. The shoots, with two true leaves, were transferred to hormone-free medium, rooting and eventually formed plantlets. Totipotent callus lines of Pleione formosana Hayata have been successfully established in this study.     

Improvement of the multiple-stress tolerance of an ethanologenic <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis> strain by freeze-thaw treatment

An effective, simple, and convenient method to improve yeast’s multiple-stress tolerance, and ethanol production was developed. After an ethanologenic Saccharomyces cerevisiae strain SC521 was treated by nine cycles of freeze-thaw, a mutant FT9-11 strain with higher multiple-stress tolerance was isolated, whose viabilities under acetic acid, ethanol, freeze-thaw, H₂O₂, and heat-shock stresses were, respectively, 23-, 26-, 10- and 7-fold more than the parent strain at an initial value 2 × 10⁷ c.f.u. per ml. Ethanol production of FT9-11 was similar (91.5 g ethanol l⁻¹) to SC521 at 30°C with 200 g glucose l⁻¹, and was better than the parent strain at 37°C (72.5 g ethanol l⁻¹), with 300 (111 g ethanol l⁻¹) or with 400 (85 g ethanol l⁻¹) g glucose l⁻¹.     

Rapid in vitro multiplication and ex vitro rooting of Malus zumi (Matsumura) Rehd

Micropropagation system of Malus zumi was optimized by studying the influence of plant growth regulators and culture conditions. The axillary buds were used for mutiplication of in vitro shoot culture on agar Murashige and Skoog (1962) (MS) medium with combination of 1 mg l⁻¹ BAP, 0.5 mg l⁻¹ NAA or 0.5 mg l⁻¹ IAA or 0.5 mg l⁻¹ IBA under 16 h photoperiod. The shoot growth in culture was not significantly affected within a broad range (5.0–7.0) of initial medium pH. The highest shoot (13) was obtained on medium containing 1.0 mg l⁻¹ BAP and 0.5 mg l⁻¹ IAA. Well-developed shoots, 35–50 mm in length, were successfully rooted ex vitro at 86.3% by a 2-h-treatment with aqueous solution containing MS salts and 100 mg l⁻¹ IBA prior to their planting in growing substrate composed of soil and vermiculite (1:1 v/v). The survival rate of transplantation reached 88.0% when transferred to field condition.     

Controlling the sucrose concentration increases Coenzyme Q10 production in fed-batch culture of <Emphasis Type="Italic">Agrobacterium tumefaciens</Emphasis>

The production yield of Coenzyme Q₁₀ (CoQ₁₀) from the sucrose consumed by Agrobacterium tumefaciens KCCM 10413 decreased, and high levels of exopolysaccharide (EPS) accumulated after switching from batch culture to fed-batch culture. Therefore, we examined the effect of sucrose concentration on the fermentation profile by A. tumefaciens. In the continuous fed-batch culture with the sucrose concentration maintained constantly at 10, 20, 30, and 40 g l⁻¹, the dry cell weight (DCW), specific CoQ₁₀ content, CoQ₁₀ production, and the production yield of CoQ₁₀ from the sucrose consumed increased, whereas EPS production decreased as maintained sucrose concentration decreased. The pH-stat fed-batch culture system was adapted for CoQ₁₀ production to minimize the concentration of the carbon source and osmotic stress from sucrose. Using the pH-stat fed-batch culture system, the DCW, specific CoQ₁₀ content, CoQ₁₀ production, and the product yield of CoQ₁₀ from the sucrose consumed increased by 22.6, 13.7, 39.3, and 39.3%, respectively, whereas EPS production decreased by 30.7% compared to those of fed-batch culture in the previous report (Ha SJ, Kim SY, Seo JH, Oh DK, Lee JK, Appl Microbiol Biotechnol, 74:974–980, 2007). The pH-stat fed-batch culture system was scaled up to a pilot scale (300 l), and the CoQ₁₀ production results obtained (626.5 mg l⁻¹ of CoQ₁₀ and 9.25 mg g DCW⁻¹ of specific CoQ₁₀ content) were similar to those obtained at the laboratory scale. Thus, an efficient and highly competitive process for microbial CoQ₁₀ production is available.     

Production of <Emphasis Type="SmallCaps">l</Emphasis>-phenylalanine from glycerol by a recombinant <Emphasis Type="Italic">Escherichia coli</Emphasis>

The production of l-phenylalanine is conventionally carried out by fermentations that use glucose or sucrose as the carbon source. This work reports on the use of glycerol as an inexpensive and abundant sole carbon source for producing l-phenylalanine using the genetically modified bacterium Escherichia coli BL21(DE3). Fermentations were carried out at 37°C, pH 7.4, using a defined medium in a stirred tank bioreactor at various intensities of impeller agitation speeds (300–500 rpm corresponding to 0.97–1.62 m s⁻¹ impeller tip speed) and aeration rates (2–8 L min⁻¹, or 1–4 vvm). This highly aerobic fermentation required a good supply of oxygen, but intense agitation (impeller tip speed ~1.62 m s⁻¹) reduced the biomass and l-phenylalanine productivity, possibly because of shear sensitivity of the recombinant bacterium. Production of l-phenylalanine was apparently strongly associated with growth. Under the best operating conditions (1.30 m s⁻¹ impeller tip speed, 4 vvm aeration rate), the yield of l-phenylalanine on glycerol was 0.58 g g⁻¹, or more than twice the best yield attainable on sucrose (0.25 g g⁻¹). In the best case, the peak concentration of l-phenylalanine was 5.6 g L⁻¹, or comparable to values attained in batch fermentations that use glucose or sucrose. The use of glycerol for the commercial production of l-phenylalanine with E. coli BL21(DE3) has the potential to substantially reduce the cost of production compared to sucrose- and glucose-based fermentations.     

Ethanol production from sweet sorghum juice in batch and fed-batch fermentations by <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Sweet sorghum juice supplemented with 0.5% ammonium sulphate was used as a substrate for ethanol production by Saccharomyces cerevisiae TISTR 5048. In batch fermentation, kinetic parameters for ethanol production depended on initial cell and sugar concentrations. The optimum initial cell and sugar concentrations in the batch fermentation were 1 × 10⁸ cells ml⁻¹ and 24 °Bx respectively. At these conditions, ethanol concentration produced (P), yield (Y _ps) and productivity (Q _p ) were 100 g l⁻¹, 0.42 g g⁻¹ and 1.67 g l⁻¹ h⁻¹ respectively. In fed-batch fermentation, the optimum substrate feeding strategy for ethanol production at the initial sugar concentration of 24 °Bx was one-time substrate feeding, where P, Y _ps and Q _p were 120 g l⁻¹, 0.48 g g⁻¹ and 1.11 g l⁻¹ h⁻¹ respectively. These findings suggest that fed-batch fermentation improves the efficiency of ethanol production in terms of ethanol concentration and product yield.     

Microbial production of 1,3-propanediol from glycerol by Klebsiella pneumoniae under micro-aerobic conditions up to a pilot scale

1,3-Propanediol (1,3-PD) can be produced from glycerol by Klebsiella pneumoniae under micro-aerobic conditions. Recently, this fed-batch fermentation process has been successfully scaled up to 1 m³. The final 1,3-PD concentration, molar yield and volumetric productivity of 72 g l⁻¹, 57% and 2.1 g l⁻¹ h⁻¹, respectively, are close to those of 75 g l⁻¹, 61%, and 2.2 g l⁻¹ h⁻¹ under anaerobic conditions. This process would be suitable for the production of 1,3-PD on a large scale.     

Production of butanol from starch-based waste packing peanuts and agricultural waste

We examined the fermentation of starch-based packing peanuts and agricultural wastes as a source of fermentable carbohydrates using Clostridium beijerinckii BA101. Using semidefined P2 medium containing packing peanuts and agricultural wastes, instead of glucose as a carbohydrate source, we measured characteristics of the fermentation including solvent production, productivity, and yield. With starch as substrate (control), the culture produced 24.7 g l⁻¹ acetone–butanol–ethanol (ABE), while with packing peanuts it produced 21.7 g l⁻¹ total ABE with a productivity of 0.20 g l⁻¹ h⁻¹ and a solvent (ABE) yield of 0.37. Cell growth in starch, packing peanuts, and agricultural wastes medium was different, possibly due to the different nature of these substrates. Using model agricultural waste, 20.3g l⁻¹ ABE was produced; when using actual waste, 14.8 g l⁻¹ ABE was produced. The use of inexpensive substrates will increase the economic viability of the conversion of biomass to butanol, and can provide new markets for these waste streams. Journal of Industrial Microbiology & Biotechnology (2002) 29, 117–123 doi: 10.1038/sj.jim.7000285 Received 14 November 2001/ Accepted in revised form 07 June 2002     

Microbial fed-batch production of 1,3-propanediol by Klebsiella pneumoniae under micro-aerobic conditions

The microbial production of 1,3-propanediol (1,3-PD) by Klebsiella pneumoniae under micro-aerobic conditions was investigated in this study. The experimental results of batch fermentation showed that the final concentration and yield of 1,3-PD on glycerol under micro-aerobic conditions approached values achieved under anaerobic conditions. However, less ethanol was produced under microaerobic than anaerobic conditions at the end of fermentation. The batch micro-aerobic fermentation time was markedly shorter than that of anaerobic fermentation. This led to an increment of productivity of 1,3-PD. For instance, the concentration, molar yield, and productivity of 1,3-PD of batch micro-aerobic fermentation by K. pneumoniae DSM 2026 were 17.65 g/l, 56.13%, and 2.94 g l^–1 h^–1, respectively, with a fermentation time of 6 h and an initial glycerol concentration of 40 g/l. Compared with DSM 2026, the microbial growth of K. pneumoniae AS 1.1736 was slow and the concentration of 1,3-PD was low under the same conditions. Furthermore, the microbial growth in fed-batch fermentation by K. pneumoniae DSM 2026 was faster under micro-aerobic than anaerobic conditions. The concentration, molar yield, and productivity of 1,3-PD in fed-batch fermentation under micro-aerobic conditions were 59.50 g/l, 51.75%, and 1.57 g l^–1 h^–1, respectively. The volumetric productivity of 1,3-PD under microaerobic conditions was almost twice that of anaerobic fed-batch fermentation, at 1.57 and 0.80 g l^–1 h^–1, respectively.     

Increased erythritol production in fed-batch cultures of Torula sp. by controlling glucose concentration

The effect of glucose concentration on erythritol production by Torula sp. was investigated. The maximum volumetric productivity of erythritol was obtained at an initial glucose concentration of 300 g l⁻¹ in batch culture. The volumetric productivity was maximal at a controlled glucose concentration of 225 g l⁻¹, reducing the lag time of the erythritol production. A fed-batch culture was established with an initial glucose concentration of 300 g l⁻¹ and with a controlled glucose concentration of 225 g l⁻¹ in medium containing phytic acid as a phosphate source. In this fed-batch culture, a final erythritol production of 192 g l⁻¹ was obtained from 400 g l⁻¹ glucose in 88 h. This corresponded to a volumetric productivity of 2.26 g l⁻¹ h⁻¹ and a 48% yield. Journal of Industrial Microbiology & Biotechnology (2001) 26, 248–252. Received 26 September 2000/ Accepted in revised form 16 January 2001     

Bioethanol production in batch mode by a native strain of <Emphasis Type="Italic">Zymomonas mobilis</Emphasis>

Two wild strains of Zymomonas mobilis were isolated (named as ML1 and ML2) from sugar cane molasses obtained from different farms of Santander, Colombia. Initially, selection of the best ethanol-producer strains was carried out using ethanol production parameters obtained with a commercial strain Z. mobilis DSM 3580. Three isolated strains were cultivated in a culture medium containing yeast extract, peptone, glucose and salts, at pH 6 and 32°C with stirring rate of 65 rpm during 62 h. The best results of ethanol production were obtained with the native strain ML1, reaching a maximum ethanol concentration of 79.78 g l⁻¹. ML1 and ML2 strains were identified as Z. mobilis, according to the morphology, biochemical tests and molecular characterization by PCR of specific DNA sequences from Z. mobilis. Subsequently, the effect of different nitrogen sources on production of ethanol was evaluated. The best results were obtained using urea at a 0.73 g/l. In this case, maximum concentration of ethanol was 83.81 g l⁻¹, with kinetic parameters of yield of ethanol on biomass (Y_P/X) = 69.01(g g⁻¹), maximum volumetric productivity of ethanol (Qp_max) = 2.28 (g l⁻¹ h⁻¹), specific productivity of ethanol (q_P) = 3.54 (h⁻¹) and specific growth rate (μ) = 0.12 h⁻¹. Finally, we studied the effect of different culture conditions (pH, temperature, stirring, C/N ratio) with a Placket-Burman′s experimental design. This optimization indicated that the most significant variables were temperature and stirring. In the best culture conditions a significant increase in all variables of response was achieved, reaching a maximum ethanol concentration of 93.55 g l⁻¹.     

Low salt medium for lactate and ethanol production by recombinant Escherichia coli B

Individual nutrient salts were experimentally varied to determine the minimum requirements for efficient l(+)-lactate production by recombinant strains of Escherichia coli B. Based on these results, AM1 medium was formulated with low levels of alkali metals (4.5 mM and total salts (4.2 g l⁻¹). This medium was equally effective for ethanol production from xylose and lactate production from glucose with average productivities of 18–19 mmol l⁻¹ h⁻¹ for both (initial 48 h of fermentation).     

Residual phosphate concentration under nitrogen-limiting conditions regulates curdlan production in Agrobacterium species

We investigated the influence of inorganic phosphate concentration on the production of curdlan by Agrobacterium species. A two-step culture method was employed where cells were first cultured, followed by curdlan production under nitrogen-limiting conditions. In the curdlan production step, cells did not grow but metabolized sugar into curdlan. Shake-flask experiments showed that the optimal phosphate concentration for curdlan production was in the range of 0.1–0.3 g l⁻¹. As the cell concentration increased from 0.42 to 1.68 g l⁻¹ in shake-flask cultures, curdlan production increased from 0.44 to 2.80 g l⁻¹. However, the optimal phosphate concentration range was not dependent upon cell concentration. The specific production rate was about 70 mg curdlan g-cell⁻¹ h⁻¹ irrespective of cell concentration. When the phosphate concentration was maintained at 0.5 g l⁻¹ under nitrogen-limiting conditions, as high as 65 g l⁻¹ of curdlan was obtained in 120 h. Journal of Industrial Microbiology & Biotechnology (2000) 25, 180–183. Received 25 October 1999/ Accepted in revised form 21 July 2000     

Development of a fed-batch process for the production of a dye-linked formaldehyde dehydrogenase in <Emphasis Type="Italic">Hyphomicrobium zavarzinii ZV 580</Emphasis>

The dye-linked formaldehyde dehydrogenase (dlFalDH) from Hyphomicrobium zavarzinii ZV 580 processes formaldehyde in a highly selective manner and without need for NAD(P). The enzyme thus has considerable potential for technical applications if the difficulties associated with its efficient production can be resolved. In this contribution, a fed-batch bioprocess is developed, which improves both the biomass production of H. zavarzinii ZV 580 (from 0.6 to 2 g l⁻¹ dry mass) and the specific dlFalDH production (from 0.1 to 0.3 units g⁻¹ biomass), resulting in an overall improvement of the productivity by more than an order of magnitude compared to the previously reported process (Klein et al., Biochem J 301:289–295, 1994). In particular, the process uses an automated feeding strategy controlled via the dissolved oxygen concentration. In addition, our results show that the growth of H. zavarzinii ZV 580 is rather sensitive toward increasing salt concentration in the culture medium. Growth is also inhibited by the presence of surfactant-based antifoam reagents. Adjustment of the pH via the addition of methylamine instead of NaOH, on the other hand, leads to an increase in biomass yield.