Continuous acetone-butanol-ethanol fermentation using SO2-ethanol-water spent liquor from spruce

SO₂–ethanol–water (SEW) spent liquor from spruce chips was successfully used for batch and continuous production of acetone, butanol and ethanol (ABE). Initially, batch experiments were performed using spent liquor to check the suitability for production of ABE. Maximum concentration of total ABE was found to be 8.79 g/l using 4-fold diluted SEW liquor supplemented with 35 g/l of glucose. The effect of dilution rate on solvent production, productivity and yield was studied in column reactor consisting of immobilized Clostridium acetobutylicum DSM 792 on wood pulp. Total solvent concentration of 12 g/l was obtained at a dilution rate of 0.21 h⁻¹. The maximum solvent productivity (4.86 g/l h) with yield of 0.27 g/g was obtained at dilution rate of 0.64 h⁻¹. Further, to increase the solvent yield, the unutilized sugars were subjected to batch fermentation.     

Metabolic engineering of Clostridium acetobutylicum for the enhanced production of isopropanol‐butanol‐ethanol fuel mixture

Butanol is considered as a superior biofuel, which is conventionally produced by clostridial acetone‐butanol‐ethanol (ABE) fermentation. Among ABE, only butanol and ethanol can be used as fuel alternatives. Coproduction of acetone thus causes lower yield of fuel alcohols. Thus, this study aimed at developing an improved Clostridium acetobutylicum strain possessing enhanced fuel alcohol production capability. For this, we previously developed a hyper ABE producing BKM19 strain was further engineered to convert acetone into isopropanol. The BKM19 strain was transformed with the plasmid pIPA100 containing the sadh (primary/secondary alcohol dehydrogenase) and hydG (putative electron transfer protein) genes from the Clostridium beijerinckii NRRL B593 cloned under the control of the thiolase promoter. The resulting BKM19 (pIPA100) strain produced 27.9 g/l isopropanol‐butanol‐ethanol (IBE) as a fuel alcohols with negligible amount of acetone (0.4 g/l) from 97.8 g/l glucose in lab‐scale (2 l) batch fermentation. Thus, this metabolically engineered strain was able to produce 99% of total solvent produced as fuel alcohols. The scalability and stability of BKM19 (pIPA100) were evaluated at 200 l pilot‐scale fermentation, which showed that the fuel alcohol yield could be improved to 0.37 g/g as compared to 0.29 g/g obtained at lab‐scale fermentation, while attaining a similar titer. To the best of our knowledge, this is the highest titer of IBE achieved and the first report on the large scale fermentation of C. acetobutylicum for IBE production. © 2013 American Institute of Chemical Engineers Biotechnol. Prog., 29:1083–1088, 2013     

Continuous propionic acid production from cheese whey usingin situ spin filter

The potential use of spin filter device to retainPropionibacterium acidipropionici in the bioreactor under continuous mode of fermentation and improve propionic acid productivity, was examined. The yield of propionic acid based on lactose concentration was 51% in batch and 54% in continuous (dilution rate=0.05 h⁻¹) operation. The yield in continuous fermentation with cell retention using spin filter of 10 micron size (dilution rate=0.05 h⁻¹) was even higher at 70% (w/w). The volumetric productivity under batch and continuous mode of operation were 0.312 g L⁻¹ h⁻¹ and 0.718 g L⁻¹ h⁻¹ respectively. Continuous fermentation with cell retention demonstrated even higher volumetric productivities at 0.98 g L⁻¹ h⁻¹ with out clogging problems It could be used for utilization of cheese whey to produce propionic acid at higher yield and productivities.     

High solid fed‐batch butanol fermentation with simultaneous product recovery: Part II—process integration

In these studies, liquid hot water (LHW) pretreated and enzymatically hydrolyzed Sweet Sorghum Bagasse (SSB) hydrolyzates were fermented in a fed‐batch reactor. As reported in the preceding paper, the culture was not able to ferment the hydrolyzate I in a batch process due to presence of high level of toxic chemicals, in particular acetic acid released from SSB during the hydrolytic process. To be able to ferment the hydrolyzate I obtained from 250 g L^?1 SSB hydrolysis, a fed‐batch reactor with in situ butanol recovery was devised. The process was started with the hydrolyzate II and when good cell growth and vigorous fermentation were observed, the hydrolyzate I was slowly fed to the reactor. In this manner the culture was able to ferment all the sugars present in both the hydrolyzates to acetone butanol ethanol (ABE). In a control batch reactor in which ABE was produced from glucose, ABE productivity and yield of 0.42 g L^?1 h^?1 and 0.36 were obtained, respectively. In the fed‐batch reactor fed with SSB hydrolyzates, these productivity and yield values were 0.44 g L^?1 h^?1 and 0.45, respectively. ABE yield in the integrated system was high due to utilization of acetic acid to convert to ABE. In summary we were able to utilize both the hydrolyzates obtained from LHW pretreated and enzymatically hydrolyzed SSB (250 g L^?1) and convert them to ABE. Complete fermentation was possible due to simultaneous recovery of ABE by vacuum. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:967–972, 2018     

Genome analysis of a hyper acetone‐butanol‐ethanol (ABE) producing Clostridium acetobutylicum BKM19

Previously the development of a hyper acetone‐butanol‐ethanol (ABE) producing Clostridium acetobutylicum BKM19 strain capable of producing 30.5% more total solvent by random mutagenesis of its parental strain PJC4BK, which is a buk mutant C. acetobutylicum ATCC 824 strain is reported. Here, BKM19 and PJC4BK strains are re‐sequenced by a high‐throughput sequencing technique to understand the mutations responsible for enhanced solvent production. In comparison with the C. acetobutylicum PJC4BK, 13 single nucleotide variants (SNVs), one deletion and one back mutation SNV are identified in the C. acetobutylicum BKM19 genome. Except for one SNV found in the megaplasmid, all mutations are found in the chromosome of BKM19. Among them, a mutation in the thlA gene encoding thiolase is further studied with respect to enzyme activity and butanol production. The mutant thiolase (thlA^V5A) is showed a 32% higher activity than that of the wild‐type thiolase (thlA^WT). In batch fermentation, butanol production is increased by 26% and 23% when the thlA^V5A gene is overexpressed in the wild‐type C. acetobutylicum ATCC 824 and in its derivative, the thlA‐knockdown TKW‐A strain, respectively. Based on structural analysis, the mutation in thiolase does not have a direct effect on the regulatory determinant region (RDR). However, the mutation at the 5^th residue seems to influence the stability of the RDR, and thus, increases the enzymatic activity and enhances solvent production in the BKM19 strain.     

Continuous solvent production by Clostridium beijerinckii BA101 immobilized by adsorption onto brick

The performance of a continuous bioreactor containing Clostridium beijerinckii BA101 adsorbed onto clay brick was examined for the fermentation of acetone, butanol, and ethanol (ABE). Dilution rates from 0.3 to 2.5 h^–1 were investigated with the highest solvent productivity of 15.8 g l^–1 h^–1 being obtained at 2.0 h^–1. The solvent yield at this dilution rate was found to be 0.38 g g^–1 and total solvent concentration was 7.9 g l^–1. The solvent yield was maximum at 0.45 at a dilution rate of 0.3 h^–1. The maximum solvent productivity obtained was found to be 2.5 times greater than most other immobilized continuous and cell recycle systems previously reported for ABE fermentation. A higher dilution rate (above 2.0 h^–1) resulted in acid production rather than solvent production. This reactor was found to be stable for over 550 h. Scanning electron micrographs (SEM) demonstrated that a large amount of C. beijerinckii cells were adsorbed onto the brick support.     

Cellulosic Butanol (ABE) Biofuel Production from Sweet Sorghum Bagasse (SSB): Impact of Hot Water Pretreatment and Solid Loadings on Fermentation Employing <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis> P260

A novel butanol fermentation process was developed in which sweet sorghum bagasse (SSB) was pretreated using liquid hot water (LHW) pretreatment technique followed by enzymatic hydrolysis and butanol (acetone butanol ethanol (ABE)) fermentation. A pretreatment temperature of 200 °C resulted in the generation of a hydrolyzate that inhibited butanol fermentation. When SSB pretreatment temperature was decreased to 190 °C (0-min holding time), the hydrolyzate was successfully fermented without inhibition and an ABE productivity of 0.51 g L^?1 h^?1 was achieved which is comparable to the 0.49 g L^?1 h^?1 observed in the control fermentation where glucose was used as a feedstock. These results are based on the use of 86 g L^?1 SSB solid loadings in the pretreatment reactors. We were also able to increase SSB solid loadings from 120 to 200 g L^?1 in the pretreatment step (190 °C) followed by hydrolysis and butanol fermentation. As pretreatment solid loadings increased, ABE yield remained in the range of 0.38–0.46. In these studies, a maximum ABE concentration of 16.88 g L^?1 was achieved. Using the LHW pretreatment technique, 88.40–96.00 % of polymeric sugars (cellulose + hemicellulose) were released in the SSB hydrolyzate. The LHW pretreatment technique does not require chemical additions and is environmentally friendly, and the hydrolyzate can be used successfully for butanol fermentation.     

Production of butanol and isopropanol with an immobilized <Emphasis Type="Italic">Clostridium</Emphasis>

Clostridium beijerinckii optinoii is a Clostridium species that produces butanol, isopropanol and small amounts of ethanol. This study compared the performances of batch and continuous immobilized cell fermentations, investigating how media flow rates and nutritional modification affected solvent yields and productivity. In 96-h batch cultures, with 80 % of the 30 g L^?1 glucose consumed in synthetic media, solvent concentration was 9.45 g L^?1 with 66.0 % as butanol. In a continuous fermentation using immobilized C. beijerinckii optinoii cells, also with 80 % of 30 g L^?1 glucose utilization, solvent productivity increased to 1.03 g L^?1 h^?1. Solvent concentration reached 12.14 g L^?1 with 63.0 % as butanol. Adjusting the dilution rate from 0.085 to 0.050 h^?1 to allow extended residence time in column was required when glucose concentration in fresh media was increased from 30 to 50 g L^?1. When acetate was used to improve the buffer capacity in media, the solvent concentration reached 12.70 on 50 g L^?1 glucose. This continuous fermentation using immobilized cells showed technical feasibility for solvent production.     

Acetone butanol ethanol (ABE) production from concentrated substrate: reduction in substrate inhibition by fed-batch technique and product inhibition by gas stripping

Acetone butanol ethanol (ABE) was produced in an integrated fed-batch fermentation-gas stripping product-recovery system using Clostridium beijerinckii BA101, with H₂ and CO₂ as the carrier gases. This technique was applied in order to eliminate the substrate and product inhibition that normally restricts ABE production and sugar utilization to less than 20 g l^–1 and 60 g l^–1, respectively. In the integrated fed-batch fermentation and product recovery system, solvent productivities were improved to 400% of the control batch fermentation productivities. In a control batch reactor, the culture used 45.4 g glucose l^–1 and produced 17.6 g total solvents l^–1 (yield 0.39 g g^–1, productivity 0.29 g l^–1 h^–1). Using the integrated fermentation-gas stripping product-recovery system with CO₂ and H₂ as carrier gases, we carried out fed-batch fermentation experiments and measured various characteristics of the fermentation, including ABE production, selectivity, yield and productivity. The fed-batch reactor was operated for 201 h. At the end of the fermentation, an unusually high concentration of total acids (8.5 g l^–1) was observed. A total of 500 g glucose was used to produce 232.8 g solvents (77.7 g acetone, 151.7 g butanol, 3.4 g ethanol) in 1 l culture broth. The average solvent yield and productivity were 0.47 g g^–1 and 1.16 g l^–1 h^–1, respectively.     

Improving performance of a gas stripping-based recovery system to remove butanol from Clostridium beijerinckii fermentation

The effect of factors such as gas recycle rate, bubble size, presence of acetone, and ethanol in the solution/broth were investigated in order to remove butanol from model solution or fermentation broth (also called acetone butanol ethanol or ABE or solvents). Butanol (8 g L^–1, model solution, Fig. 2) stripping rate was found to be proportional to the gas recycle rate. In the bubble size range attempted (<0.5 and 0.5–5.0 mm), the bubble size did not have any effect on butanol removal rate (Fig. 3, model solution). In Clostridium beijerinckii fermentation, ABE productivity was reduced from 0.47 g L^–1 h^–1 to 0.25 g L^–1 h^–1 when smaller (<0.5 mm) bubble size was used to remove ABE (Fig. 4, results reported as butanol/ABE concentration). The productivity was reduced as a result of addition of an excessive amount of antifoam used to inhibit the production of foam caused by the smaller bubbles. This suggested that the fermentation was negatively affected by antifoam.Mention of trade names of commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

Butanol production from wheat straw hydrolysate using <Emphasis Type="Italic">Clostridium beijerinckii</Emphasis>

In these studies, butanol (acetone butanol ethanol or ABE) was produced from wheat straw hydrolysate (WSH) in batch cultures using Clostridium beijerinckii P260. In control fermentation 48.9 g L⁻¹ glucose (initial sugar 62.0 g L⁻¹) was used to produce 20.1 g L⁻¹ ABE with a productivity and yield of 0.28 g L⁻¹ h⁻¹ and 0.41, respectively. In a similar experiment where WSH (60.2 g L⁻¹ total sugars obtained from hydrolysis of 86 g L⁻¹ wheat straw) was used, the culture produced 25.0 g L⁻¹ ABE with a productivity and yield of 0.60 g L⁻¹ h⁻¹ and 0.42, respectively. These results are superior to the control experiment and productivity was improved by 214%. When WSH was supplemented with 35 g L⁻¹ glucose, a reactor productivity was improved to 0.63 g L⁻¹ h⁻¹ with a yield of 0.42. In this case, ABE concentration in the broth was 28.2 g L⁻¹. When WSH was supplemented with 60 g L⁻¹ glucose, the resultant medium containing 128.3 g L⁻¹ sugars was successfully fermented (due to product removal) to produce 47.6 g L⁻¹ ABE, and the culture utilized all the sugars (glucose, xylose, arabinose, galactose, and mannose). These results demonstrate that C. beijerinckii P260 has excellent capacity to convert biomass derived sugars to solvents and can produce over 28 g L⁻¹ (in one case 41.7 g L⁻¹ from glucose) ABE from WSH. Medium containing 250 g L⁻¹ glucose resulted in no growth and no ABE production. Mixtures containing WSH + 140 g L⁻¹ glucose (total sugar approximately 200 g L⁻¹) showed poor growth and poor ABE production. Mention of trade names or commercial products in this article is solely for the purpose of providing scientific information and does not imply recommendation or endorsement by the United States Department of Agriculture.     

Effect of cell recycle on continuous butanol-acetone fermentation with Clostridium acetobutylicum under phosphate limitation

Summary An overflow filtration unit for cell recycle with Clostridium acetobutylicum was developed. A cellulose-triacetate ultrafiltration membrane with a cut-off volume of 20 000 MW was found to work best. C. acetobutylicum was grown in continuous culture under phosphate limitation (0.74 mM) at a pH value of 4.4 with cell recycle, the cell dry weight in the culture vessel reached 13.1 g/l at a dilution rate of D=0.10 h^-1 and 37°C. 377 mM of glucose were fermented to 190 mM butanol, 116.2 mM acetone and 25.8 mM ethanol. Total acids were 47.6 mM. The butanol productivity was 1.41 g/l/h. At a dilution rate of 0.40 h^-1 the butanol productivity was increased to 4.1 g/l/h but glucose consumption was decreased to 285 mM and butanol, acetone and ethanol production to 138.2, 97.5, 16.5 mM, respectively.     

Performance of batch, fed-batch, and continuous A-B-E fermentation with pH-control

Batch, fed-batch, and continuous A-B-E fermentations were conducted and compared with pH controlled at 4.5, the optimal range for solvent production. While the batch mode provides the highest solvent yield, the continuous mode was preferred in terms of butanol yield and productivity. The highest butanol yield and productivity found in the continuous fermentation at dilution rate of 0.1 h⁻¹ were 0.21 g-butanol/g-glucose and 0.81 g/L/h, respectively. In the continuous and fed-batch fermentation, the time needed for passing acidogenesis to solventogenesis was an intrinsic hindrance to higher butanol productivity. Therefore, a low dilution rate is suggested for the continuous A-B-E fermentation, while the fed-batch mode is not suggested for solvent production. While 3:6:1 ratio of acetone, butanol, and ethanol is commonly observed from A-B-E batch fermentation by Clostridium acetobutylicum when the pH is uncontrolled, up to 94% of the produced solvent was butanol in the chemostat with pH controlled at 4.5.     

Butanol production by Clostridium acetobutylicum in a continuous packed bed reactor

In this study, we report on a butanol production process by immobilized Clostridium acetobutylicum in a continuous packed bed reactor (PBR) using Tygon^® rings as a carrier. The medium was a solution of lactose (15–30 g/L) and yeast extract (3 g/L) to emulate the cheese whey, an abundant lactose-rich wastewater. The reactor was operated under controlled conditions with respect to the pH and to the dilution rate. The pH and the dilution rate ranged between 4 and 5, the dilution rate between 0.54 and 2.4 h^?1 (2.5 times the maximum specific growth rate assessed for suspended cells). The optimal performance of the reactor was recorded at a dilution rate of 0.97 h^?1: the butanol productivity was 4.4 g/Lh and the selectivity of solvent in butanol was 88%_w.     

Butanol production from sweet sorghum bagasse with high solids content: Part I—comparison of liquid hot water pretreatment with dilute sulfuric acid

In these studies, we pretreated sweet sorghum bagasse (SSB) using liquid hot water (LHW) or dilute H₂SO₄ (2 g L^?1) at 190°C for zero min (as soon as temperature reached 190°C, cooling was started) to reduce generation of sugar degradation fermentation inhibiting products such as furfural and hydroxymethyl furfural (HMF). The solids loading were 250–300 g L^?1. This was followed by enzymatic hydrolysis. After hydrolysis, 89.0 g L^?1 sugars, 7.60 g L^?1 acetic acid, 0.33 g L^?1 furfural, and 0.07 g L^?1 HMF were released. This pretreatment and hydrolysis resulted in the release of 57.9% sugars. This was followed by second hydrolysis of the fibrous biomass which resulted in the release of 43.64 g L^?1 additional sugars, 2.40 g L^?1 acetic acid, zero g L^?1 furfural, and zero g L^?1 HMF. In both the hydrolyzates, 86.3% sugars present in SSB were released. Fermentation of the hydrolyzate I resulted in poor acetone‐butanol‐ethanol (ABE) fermentation. However, fermentation of the hydrolyzate II was successful and produced 13.43 g L^?1 ABE of which butanol was the main product. Use of 2 g L^?1 H₂SO₄ as a pretreatment medium followed by enzymatic hydrolysis resulted in the release of 100.6–93.8% (w/w) sugars from 250 to 300 g L^?1 SSB, respectively. LHW or dilute H₂SO₄ were used to economize production of cellulosic sugars from SSB. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:960–966, 2018     

Improvements of metabolites tolerance in <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> by micronutrient zinc supplementation

Micronutrient zinc is of great importance for acetone-butanol-ethanol (ABE) fermentation by Clostridium acetobutylicum. The effect of zinc supplementation on toxic metabolites (formic, acetic, butyric acid and butanol) tolerance during ABE fermentation was investigated under various stress-shock conditions without pH control. Great improvements on cell growth, glucose utilization and butanol production were achieved. In the presence of 0.45 g/L formic acid, zinc contributed to 11.28 g/L butanol produced from 55.24 g/L glucose compared to only 5.27 g/L butanol from 29.49 g/L glucose in the control without zinc supplementation. More importantly, relatively higher levels of 7.5 g/L acetic acid, 5.5 g/L butyric acid and 18 g/L butanol could be tolerated by C. acetobutylicum with zinc supplementation while no fermentation was observed under the same stress-shock condition respectively, suggesting that the acids and butanol tolerance in C. acetobutylicum could be significantly facilitated by pleiotropic regulation of micronutrient zinc. Thus, this paper provides an efficient bioprocess engineering strategy for improving stress tolerance in Clostridium species.     

Engineering Clostridium acetobutylicum for production of kerosene and diesel blendstock precursors

Processes for the biotechnological production of kerosene and diesel blendstocks are often economically unattractive due to low yields and product titers. Recently, Clostridium acetobutylicum fermentation products acetone, butanol, and ethanol (ABE) were shown to serve as precursors for catalytic upgrading to higher chain-length molecules that can be used as fuel substitutes. To produce suitable kerosene and diesel blendstocks, the butanol:acetone ratio of fermentation products needs to be increased to 2–2.5:1, while ethanol production is minimized. Here we show that the overexpression of selected proteins changes the ratio of ABE products relative to the wild type ATCC 824 strain. Overexpression of the native alcohol/aldehyde dehydrogenase (AAD) has been reported to primarily increase ethanol formation in C. acetobutylicum. We found that overexpression of the AAD^D485G variant increased ethanol titers by 294%. Catalytic upgrading of the 824(aad^D485G) ABE products resulted in a blend with nearly 50 wt%≤C₉ products, which are unsuitable for diesel. To selectively increase butanol production, C. beijerinckii aldehyde dehydrogenase and C. ljungdhalii butanol dehydrogenase were co-expressed (strain designate 824(Cb ald-Cl bdh)), which increased butanol titers by 27% to 16.9 g L⁻¹ while acetone and ethanol titers remained essentially unaffected. The solvent ratio from 824(Cb ald-Cl bdh) resulted in more than 80 wt% of catalysis products having a carbon chain length≥C₁₁ which amounts to 9.8 g L⁻¹ of products suitable as kerosene or diesel blendstock based on fermentation volume. To further increase solvent production, we investigated expression of both native and heterologous chaperones in C. acetobutylicum. Expression of a heat shock protein (HSP33) from Bacillus psychrosaccharolyticus increased the total solvent titer by 22%. Co-expression of HSP33 and aldehyde/butanol dehydrogenases further increased ABE formation as well as acetone and butanol yields. HSP33 was identified as the first heterologous chaperone that significantly increases solvent titers above wild type C. acetobutylicum levels, which can be combined with metabolic engineering to further increase solvent production.     

Continuous bio-catalytic conversion of sugar mixture to acetone–butanol–ethanol by immobilized <Emphasis Type="Italic">Clostridium acetobutylicum</Emphasis> DSM 792

Continuous production of acetone, n-butanol, and ethanol (ABE) was carried out using immobilized cells of Clostridium acetobutylicum DSM 792 using glucose and sugar mixture as a substrate. Among various lignocellulosic materials screened as a support matrix, coconut fibers and wood pulp fibers were found to be promising in batch experiments. With a motive of promoting wood-based bio-refinery concept, wood pulp was used as a cell holding material. Glucose and sugar mixture (glucose, mannose, galactose, arabinose, and xylose) comparable to lignocellulose hydrolysate was used as a substrate for continuous production of ABE. We report the best solvent productivity among wild-type strains using column reactor. The maximum total solvent concentration of 14.32 g L⁻¹ was obtained at a dilution rate of 0.22 h⁻¹ with glucose as a substrate compared to 12.64 g L⁻¹ at 0.5 h⁻¹ dilution rate with sugar mixture. The maximum solvent productivity (13.66 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.9 h⁻¹ with glucose as a substrate whereas solvent productivity (12.14 g L⁻¹ h⁻¹) was obtained at a dilution rate of 1.5 h⁻¹ with sugar mixture. The immobilized column reactor with wood pulp can become an efficient technology to be integrated with existing pulp mills to convert them into wood-based bio-refineries.     

Controlled-ph batch butanol-acetone fermentation by low acid producing Clostridium acetobutylicum B18

Summary C. acetobutylicum B18 produced a large amount of butanol over a wide range of pH (4.5–6.0). At pH 6.0 fermentation and cell growth were most active at pH 6.0, and the highest values of glucose consumption rate (4.37 g/L-h), butanol productivity (1.0 g/L-h), butyric acid recycle rate (0.31 g/L-h), and cell growth rate (0.2 h^-1) were obtained. There existed a critical pH between 6.0 and 6.5 above which cells switched to organic acid producing mode. Clostridial stage appeared essential for solvent production by strain B18 but sporulation was not necessary for solvent formation.