A statistical analysis of the effect of substrate utilization and shear stress on the kinetics of biofilm detachment

One of the least understood processes affecting biofilm accumulation is detachment. Detachment is the removal of cells and cell products from an established biofilm and subsequent entrainment in the bulk liquid. The goal of this research was to determine the effects of shear stress and substrate loading rate on the rate of biofilm detachment.Monopopulation Pseudomonas aeruginosa and undefined mixed population biofilms were grown on glucose in a RotoTorque biofilm reactor. Three levels of shear stress and substrate loading rate were used to determine their effects on the rate of detachment. Suspended cell concentrations were monitored to determine detachment rates, while other variables were measured to determine their influence on the detachment rate. Results indicate that detachment rate is directly related to biofilm growth rate and that factors which limit growth rate will also limit detachment rate. No significant influence of shear on detachment rate was observed.A new kinetic expression that incorporates substrate utilization rate, yield, and biofilm thickness was compared to published detachment expressions and gives a better correlation of data obtained both in this research and from previous research projects, for both mono- and mixed-population biofilms. (c) John Wiley & Sons, Inc.     

Biofilm material properties as related to shear-induced deformation and detachment phenomena

Biofilms of various Pseudomonas aeruginosa strains were grown in glass flow cells under laminar and turbulent flows. By relating the physical deformation of biofilms to variations in fluid shear, we found that the biofilms were viscoelastic fluids which behaved like elastic solids over periods of a few seconds but like linear viscous fluids over longer times. These data can be explained using concepts of associated polymeric systems, suggesting that the extracellular polymeric slime matrix determines the cohesive strength. Biofilms grown under high shear tended to form filamentous streamers while those grown under low shear formed an isotropic pattern of mound-shaped microcolonies. In some cases, sustained creep and necking in response to elevated shear resulted in a time-dependent fracture failure of the “tail” of the streamer from the attached upstream “head.” In addition to structural differences, our data suggest that biofilms grown under higher shear were more strongly attached and were cohesively stronger than those grown under lower shears. Received 06 February 2002/ Accepted in revised form 13 June 2002     

A general description of detachment for multidimensional modelling of biofilms

A general method for describing biomass detachment in multidimensional biofilm modelling is introduced. Biomass losses from processes acting on the entire surface of the biofilm, such as erosion, are modelled using a continuous detachment speed function F(det). Discrete detachment events, i.e. sloughing, are implicitly derived from simulations. The method is flexible to allow F(det) to take several forms, including expressions dependent on any state variables such as the local biofilm density. This methodology for biomass detachment was integrated with multidimensional (2D and 3D) particle-based multispecies biofilm models by using a novel application of the level set method. Application of the method is illustrated by trends in the dynamics of biofilms structure and activity derived from simulations performed on a simple model considering uniform biomass (case study I) and a model discriminating biomass composition in heterotrophic active mass, extracellular polymeric substances (EPS) and inert mass (case study II). Results from case study I demonstrate the effect of applied detachment forces as a fundamental factor influencing steady-state biofilm activity and structure. Trends from experimental observations reported in literature were correctly described. For example, simulation results indicated that biomass sloughing is reduced when erosion forces are increased. Case study II illustrates the application of the detachment methodology to systems with non-uniform biomass composition. Simulations carried out at different bulk concentrations of substrate show changes in biofilm structure (in terms of shape, density and spatial distribution of biomass components) and activity (in terms of oxygen and substrate consumption) as a consequence of either oxygen-limited or substrate-limited growth.     

Cell‐mediated deposition of porous silica on bacterial biofilms

Living hybrid materials that respond dynamically to their surrounding environment have important applications in bioreactors. Silica based sol–gels represent appealing matrix materials as they form a mesoporous biocompatible glass lattice that allows for nutrient diffusion while firmly encapsulating living cells. Despite progress in sol–gel cellular encapsulation technologies, current techniques typically form bulk materials and are unable to generate regular silica membranes over complex geometries for large‐scale applications. We have developed a novel biomimetic encapsulation technique whereby endogenous extracellular matrix molecules facilitate formation of a cell surface specific biomineral layer. In this study, monoculture Pseudomonas aeruginosa and Nitrosomonas europaea biofilms are exposed to silica precursors under different acid conditions. Scanning electron microscopy (SEM) imaging and electron dispersive X‐ray (EDX) elemental analysis revealed the presence of a thin silica layer covering the biofilm surface. Cell survival was confirmed 30 min, 30 days, and 90 days after encapsulation using confocal imaging with a membrane integrity assay and physiological flux measurements of oxygen, glucose, and NH. No statistical difference in viability, oxygen flux, or substrate flux was observed after encapsulation in silica glass. Shear induced biofilm detachment was assessed using a particle counter. Encapsulation significantly reduced detachment rate of the biofilms for over 30 days. The results of this study indicate that the thin regular silica membrane permits the diffusion of nutrients and cellular products, supporting continued cellular viability after biomineralization. This technique offers a means of controllably encapsulating biofilms over large surfaces and complex geometries. The generic deposition mechanism employed to form the silica matrix can be translated to a wide range of biological material and represents a platform encapsulation technology. Biotechnol. Bioeng. 2011;108: 2249–2260. © 2011 Wiley Periodicals, Inc.     

Effects of ship‐induced waves on littoral benthic invertebrates

1. Ship‐induced waves can affect the physical characteristics of lake and river shorelines, and laboratory studies have shown effects on littoral invertebrates. Here, we explored whether these effects could be observed under field conditions along a natural lake shore affected by wave sequences (trains) produced by boats. 2. Individuals of five invertebrate species (Bithynia tentaculata, Calopteryx splendens, Dikerogammarus villosus, Gammarus roeselii, Laccophilus hyalinus) were exposed to waves with increasing shear stress in five habitats differing in structural complexity. 3. Detachment of invertebrates increased with increasing shear stress and was best modelled using sigmoid response curves. Habitat structural complexity mitigated the effects of shear stress, and detachment rate was influenced more by habitat type than by species. A threshold (90% of the individual invertebrates unaffected) stress level of 0.64 N m^?2 was found for a structurally complex reed habitat, compared to 0.37 N m^?2 for a simple sand habitat. 4. Shear stress associated with wave trains created by recreational boating at a distance of 35 m from the shore and at a speed of 11 km h^?1 resulted in 45% detachment of littoral invertebrates. Decreasing the boat‐to‐shore distance to 20 m increased wave shear stress by 30% and invertebrate detachments up to 75%. 5. Disturbance of littoral habitats and invertebrate assemblages are widespread in inland waters used for recreational and/or commercial navigation. Our findings show that the integrity of littoral zones of navigable surface waters could be much improved by implementing management measures such as physically protecting complex habitats with dense reed belts and tree roots, and reducing boat speeds and increasing their minimum shoreline distance.     

Analysis of the mechanical stability and surface detachment of mature Streptococcus mutans biofilms by applying a range of external shear forces

Well-established biofilms formed by Streptococcus mutans via exopolysaccharide matrix synthesis are firmly attached to tooth surfaces. Enhanced understanding of the physical properties of mature biofilms may lead to improved approaches to detaching or disassembling these highly organized and adhesive structures. Here, the mechanical stability of S. mutans biofilms was investigated by determining their ability to withstand measured applications of shear stress using a custom-built device. The data show that the initial biofilm bulk (~ 50% biomass) was removed after exposure to 0.184 and 0.449 N m^?2 for 67 and 115 h old biofilms. However, removal of the remaining biofilm close to the surface was significantly reduced (vs initial bulk removal) even when shear forces were increased 10-fold. Treatment of biofilms with exopolysaccharide-digesting dextranase substantially compromised their mechanical stability and rigidity, resulting in bulk removal at a shear stress as low as 0.027 N m^?2 and > a two-fold reduction in the storage modulus (G′). The data reveal how incremental increases in shear stress cause distinctive patterns of biofilm detachment, while demonstrating that the exopolysaccharide matrix modulates the resistance of biofilms to mechanical clearance.     

Shear‐induced diffusion of red blood cells measured with dynamic light scattering‐optical coherence tomography

Quantitative measurements of intravascular microscopic dynamics, such as absolute blood flow velocity, shear stress and the diffusion coefficient of red blood cells (RBCs), are fundamental in understanding the blood flow behavior within the microcirculation, and for understanding why diffuse correlation spectroscopy (DCS) measurements of blood flow are dominantly sensitive to the diffusive motion of RBCs. Dynamic light scattering‐optical coherence tomography (DLS‐OCT) takes the advantages of using DLS to measure particle flow and diffusion within an OCT resolution‐constrained three‐dimensional volume, enabling the simultaneous measurements of absolute RBC velocity and diffusion coefficient with high spatial resolution. In this work, we applied DLS‐OCT to measure both RBC velocity and the shear‐induced diffusion coefficient within penetrating venules of the somatosensory cortex of anesthetized mice. Blood flow laminar profile measurements indicate a blunted laminar flow profile and the degree of blunting decreases with increasing vessel diameter. The measured shear‐induced diffusion coefficient was proportional to the flow shear rate with a magnitude of ~0.1 to 0.5 × 10^?6 mm². These results provide important experimental support for the recent theoretical explanation for why DCS is dominantly sensitive to RBC diffusive motion.      

3D finite element model of biofilm detachment using real biofilm structures from CLSM data

In this work, a three‐dimensional model of fluid–structure interactions (FSI) in biofilm systems is developed in order to simulate biofilm detachment as a result of mechanical processes. Therein, fluid flow past the biofilm surface results in a mechanical load on the structure which in turn causes internal stresses in the biofilm matrix. When the strength of the matrix is exceeded parts of the structure are detached. The model is used to investigate the influence of several parameters related to the mechanical strength of the biofilm matrix, Young's modulus, Reynolds number, and biofilm structure on biofilm detachment. Variations in biofilm strength and flow conditions significantly influence the simulation outcome. With respect to structural properties the model is widely independent from a change of Young's modulus. A further result of this work indicates that the change of biofilm structure due to growth or other processes will significantly change the stress distribution in the biofilm and thereby the detachment rate. An increase of the mechanical load by increasing fluid flow results in a flat surface of the remaining biofilm structure. It is concluded that the change of structure during biofilm development is the key determinant in terms of the detachment behavior. Biotechnol. Bioeng. 2009;103: 177–186. © 2008 Wiley Periodicals, Inc.     

Comparative susceptibility of planktonic and 3‐day‐old Salmonella Typhimurium biofilms to disinfectants

Aims: To compare the susceptibility of a 3‐day‐old biofilm and planktonic Salmonella to disinfectants at different exposure times. We hypothesize that Salmonella biofilms are more resilient to disinfectants compared to planktonic Salmonella. Methods and Results: The susceptibility of planktonic cells to disinfectants was tested by a modified version of the Council of Europe suspension test EN 1276. Salmonella biofilms were formed using the Calgary Biofilm Device. Results show that 3‐day‐old Salmonella biofilms are less susceptible to the disinfectants benzalkonium chloride, chlorhexidine gluconate, citric acid, quaternary ammonium compounds, sodium hypochlorite (SH) and ethanol, compared to planktonic Salmonella. Surprisingly, the results also demonstrate that low concentrations of SH were more effective against a 3‐day‐old biofilm compared to high concentrations of SH. Conclusions: While all the disinfectants evaluated were able to reduce biofilm‐associated cells at concentrations and contact times sufficient to eliminate planktonic cells, there were still sufficient viable cells remaining in the biofilm to cause further contamination and potential infection. Significance and Impact of the Study: Protocols for the use of chemical disinfectants need to include biofilm susceptibility testing. There is a requirement for an effective and standardized tool for determining the susceptibility of biofilms to disinfectants.     

A thin‐walled polydimethylsiloxane bioreactor for high‐density hepatocyte sandwich culture

In vitro drug testing requires long‐term maintenance of hepatocyte liver specific functions. Hepatocytes cultured at a higher seeding density in a sandwich configuration exhibit an increased level of liver specific functions when compared to low density cultures due to the better cell to cell contacts that promote long term maintenance of polarity and liver specific functions. However, culturing hepatocytes at high seeding densities in a standard 24‐well plate poses problems in terms of the mass transport of nutrients and oxygen to the cells. In view of this drawback, we have developed a polydimethylsiloxane (PDMS) bioreactor that was able to maintain the long‐term liver specific functions of a hepatocyte sandwich culture at a high seeding density. The bioreactor was fabricated with PDMS, an oxygen permeable material, which allowed direct oxygenation and perfusion to take place simultaneously. The mass transport of oxygen and the level of shear stress acting on the cells were analyzed by computational fluid dynamics (CFD). The combination of both direct oxygenation and perfusion has a synergistic effect on the liver specific function of a high density hepatocyte sandwich culture over a period of 9 days. Biotechnol. Bioeng. 2013; 110: 1663–1673. © 2012 Wiley Periodicals, Inc.     

Enhanced germicidal effects of pulsed UV‐LED irradiation on biofilms

Aims: The major objective of the study was to evaluate the enhanced germicidal effects of low‐frequency pulsed ultraviolet A (UVA)‐light‐emitting diode (LED) on biofilms. Methods and Results: The germicidal effects of UVA‐LED irradiation (365 nm, 0·28 mW cm^?2, in pulsed or continuous mode) on Candida albicans or Escherichia coli biofilms were evaluated by determining colony‐forming units. The morphological change of microbial cells in biofilms was observed using scanning electron microscopy. After 5‐min irradiation, over 90% of viable micro‐organisms in biofilms had been killed, and pulsed irradiation (1–1000 Hz) had significantly greater germicidal ability than continuous irradiation. Pulsed irradiation (100 Hz, 60 min) almost completely killed micro‐organisms in biofilm (>99·9%), and 20‐min irradiation greatly damaged both microbial species. Interestingly, few hyphae were found in irradiated Candida biofilms. Moreover, mannitol treatment, a scavenger of hydroxyl radicals (OH^?), significantly protected viable micro‐organisms in biofilms from UVA‐LED irradiation. Conclusions: The study demonstrated that pulsed UVA‐LED irradiation has a strong germicidal effect (maximum at 100 Hz, over 5‐min irradiation) and causes the disappearance of hyphal forms of Candida. Significance and Impact of the Study: This study can assist in developing a low‐frequency pulsed UVA‐LED system to be applied to pathogenic biofilms for disinfection.     

Determination of biomass detachment rate coefficients in anaerobic fluidized-bed-GAC reactors

In this study a simple analytical technique that determines the active biomass in a sample capable of degrading specific substrates anaerobically was developed and used to measure first-order detachment rate coefficients of acetate and phenol utilizing organisms. Different detachment rate coefficients were measured for the two microbial populations. A general relationship between the detachment rate coefficients and biomass accumulation was developed. The detachment rate coefficient was found to increase sharply after a certain biomass accumulation until it reaches a maximum, after which it decreases continuously with increasing biomass until it levels off at a constant value independent of biomass. Detachment rate coefficients measured in different reactors, operating at different conditions with respect to loading, biological SRT, and attachment media particle size, were in close agreement with each other after being normalized to the shear stress and daily methane production rate per unit biofilm area.     

Inactivation of Pseudomonas aeruginosa biofilms formed under high shear stress on various hydrophilic and hydrophobic surfaces by a continuous flow of ozonated water

Abstract

The inactivation of Pseudomonas aeruginosa biofilms grown on glass under high shear stress and exposed to a range of dissolved ozone concentrations (2, 5 and 7?ppm) at 10 and 20?min was investigated. The regression equation, log reduction (biofilm)?=?0.64?+?0.59×(C – 2)?+?0.33×(T – 10), described the dependence of biofilm inactivation on the dissolved ozone concentration (C, ppm) and contact time (T, min). The predicted D-values were 11.1, 5.7 and 2.2?min at 2, 5 and 7?ppm, respectively. Inactivation of biofilms grown on various surfaces was tested at a single dissolved ozone concentration of 5?ppm and a single exposure time of 20?min. Biofilms grown on plastic materials showed inactivation results similar to that of biofilms on glass, while biofilms grown on ceramics were statistically significantly more difficult to inactivate, suggesting the importance of utilizing non-porous materials in industrial and clinical settings.     

Increased curvature of hollow fiber membranes could up‐regulate differential functions of renal tubular cell layers

Tissue engineering devices as in vitro cell culture systems in scaffolds has encountered the bottleneck due to their much lower cell functions than real tissues/organs in vivo. Such situation has been improved in some extent by mimicking the cell microenvironments in vivo from either chemical or physical ways. However, microenvironmental curvature, commonly seen in real tissues/organs, has never been manipulated to regulate the cell performance in vitro. In this regard, this paper fabricated polysulfone membranes with or without polyethylene glycol modification to investigate the impact of curvature on two renal tubular cells. Regardless the varying membrane curvatures among hollow fiber membranes of different diameters and flat membrane of zero curvature, both renal cells could well attach at 4 h of seeding and form similar confluent layers at 6 days on each membrane. Nevertheless, the renal cells on hollow fibers, though showing confluent morphology as those on flat membranes, expressed higher renal functions and, moreover, the renal functions significantly increased with the membrane curvature among hollow fibers. Such upregulation on functions was unassociated with mass transport barrier of hollow fibers, because the cultures on lengthwise cut hollow fibers without mass transfer barrier showed same curvature effect on renal functions as whole hollow fibers. It could be proposed that the curvature of hollow fiber membrane approaching to the large curvature in kidney tubules increased the mechanical stress in the renal cells and thus might up‐regulate the renal cell functions. In conclusion, the increase of substrate curvature could up‐regulate the cell functions without altering the confluent cell morphology and this finding will facilitate the design of functional tissue engineering devices. Biotechnol. Bioeng. 2013; 110: 2173–2183. © 2013 Wiley Periodicals, Inc.     

Synthesis of Injectable Shear‐Thinning Biomaterials of Various Compositions of Gelatin and Synthetic Silicate Nanoplatelet

Injectable shear‐thinning biomaterials (iSTBs) have great potential for in situ tissue regeneration through minimally invasive therapeutics. Previously, an iSTB was developed by combining gelatin with synthetic silicate nanoplatelets (SNPs) for potential application to hemostasis and endovascular embolization. Hence, iSTBs are synthesized by varying compositions of gelatin and SNPs to navigate their material, mechanical, rheological, and bioactive properties. All compositions (each component percentage; 1.5–4.5%/total solid ranges; 3–9%) tested are injectable through both 5 Fr general catheter and 2.4 Fr microcatheter by manual pressure. In the results, an increase in gelatin contents causes decrease in swellability, increase in freeze‐dried hydrogel scaffold porosity, increase in degradability and injection force during iSTB fabrication. Meanwhile, the amount of SNPs in composite hydrogels is mainly required to decrease degradability and increase shear thinning properties of iSTB. Finally, in vitro and in vivo biocompatibility tests show that the 1.5–4.5% range gelatin–SNP iSTBs are not toxic to the cells and animals. All results demonstrate that the iSTB can be modulated with specific properties for unmet clinical needs. Understanding of mechanical and biological consequences of the changing gelatin–SNP ratios through this study will shed light on the biomedical applications of iSTB on specific diseases.