A highly selective and sensitive turn‐on fluorescent probe for the detection of Al3+ and its bioimaging

A novel fluorescent sensor, 1‐((2‐hydroxynaphthalen‐1‐yl)methylene)urea (ocn) has been designed and applied as a highly selective and sensitive fluorescent probe for recognition of Al³⁺ in Tris–HCl (pH = 7.20) solution. The probe ocn exhibits an excellent selectivity to Al³⁺ over other examined metal ions, anions and amino acids with a prominent fluorescence ‘turn‐on’ at 438 nm. ocn binds to Al³⁺ with a 2:1 binding stoichiometry and the detection limit was 0.3 μM. Furthermore, its capability of biological application was evaluated and the results showed that the sensor could be used to detect Al³⁺ in living cells.     

Tetrasubstituted cyclopentenone‐based fluorescent chemosensors for the selective detection of Fe3+ and Cu2+ ions

Fluorescent chemosensors based on 4‐hydroxy cyclopentenones were synthesized by the base catalyzed reaction of 1,5‐diphenyl‐pentane‐1,3,5‐trione with benzil and thenil. The molecule obtained by the benzil reaction was found to be useful for the selective detection of Fe³⁺ by fluorescence turn‐off, while the molecule synthesized by the thenil reaction was useful for selective detection of Cu²⁺ by fluorescent turn‐on. Details of the synthesis, complexation mode, nature of binding, reversibility, and pH studies of the two sensors are discussed. The studies revealed that the sensors were suitable for determining Fe³⁺ and Cu²⁺ content in real water samples.     

Two new rhodamine‐based fluorescent chemosensors for Fe3+ in aqueous solution

Two new rhodamine‐based fluorescent probes were synthesized and characterized by NMR, high resolution mass spectrometer (HR‐MS) and IR. The probes displayed a high selectivity for Fe³⁺ among environmentally and biologically relevant metal ions in aqueous solution (CH₃OH–H₂O = 3 : 2, v/v). The significant changes in the fluorescence color could be used for naked‐eye detection. Job's plot, IR and ¹H NMR indicated the formation of 1: 1 complexes between sensor 1 and Fe³⁺. The reversibility establishes the potential of both probes as chemosensors for Fe³⁺ detection. The probe showed highly selectivity in aqueous solution and could be used over the pH range between 5 and 9. A simple paper test‐strip system for the rapid monitoring of Fe³⁺ was developed, indicating its convenient use in environmental samples. Copyright © 2014 John Wiley & Sons, Ltd.     

Three colorimetric and off–on fluorescent chemosensors for Fe3+ in aqueous media

Three Rhodamine B derivatives were synthesized and characterized by ESI‐MS, NMR, HR‐MS and IR. The probes exhibit high selectivity and sensitivity towards Fe³⁺ over other metal ions in CH₃CN–water. Upon the addition of Fe³⁺, the spirocyclic ring of the probe was opened and a significant enhancement of visible color and fluorescence within the range of 540–700 nm was observed. The colorimetric and fluorescent response to Fe³⁺ can be conveniently detected even by the naked eye, which provides a facile method for the visual detection of Fe³⁺. Job's plot, fluorescence titration and MS indicated the formation of 1:2 complexes between the probes and Fe³⁺. The reversibility of the reaction establishes the potential of these probes as chemosensors for Fe³⁺ detection. Copyright © 2013 John Wiley & Sons, Ltd.     

A novel colorimetric fluorescence sensor for Fe3+ based on quinoline Schiff base

A novel fluorescent sensor bearing a quinoline and an anisidine moiety has been developed for highly selective detection of Fe³⁺, which shows photo‐induced electron transfer (PET) behavior induced by Fe³⁺. Binding of Fe³⁺ to the sensor induced the electron of C = N group transfer from quinoline to iron, the result exhibits fluorescent enhancement. With the features of easy synthesis, simple structural skeleton and excellent sensing ability, the newly synthesized chemosensor also applied as a highly selective fluorescent probe in complex samples containing various competitive metal ions. The probe could fulfill various needs in biological and environmental fields.     

A new Schiff base as a turn‐off fluorescent sensor for Cu2+ and its photophysical properties

A new Schiff base receptor 1 was synthesized and its photophysical properties were investigated by absorption, emission and excitation techniques. Furthermore, its chromogenic and fluorogenic sensing abilities towards various metal ions were examined. Receptor 1 selectively detects Cu²⁺ ion through fluorescence quenching and detection was not inhibited in the presence of other metal ions. From fluorescence titration, the limit of detection of receptor 1 as a fluorescent ‘turn‐off’ sensor for the analysis of Cu²⁺ was estimated to be 0.35 μM.     

Green synthesis of fluorescent carbon dots using chloroplast dispersions as precursors and application for Fe3+ ion sensing

Water‐soluble carbon dots (CDs) were synthesized using a one‐step hydrothermal treatment of chloroplast dispersions extracted from fresh leaves as a green carbon source. The CD solution showed an emission peak centred at 445 nm when excited at 300 nm. The synthesized CDs were uniform and monodispersed with an average size of 5.6 nm. When adding ferric(III) ions (Fe³⁺) to the solution of the original CDs, the fluorescence intensity decreased significantly. Based on the linear relationship between fluorescence intensity and concentration of Fe³⁺ ions, an effective method for rapid, sensitive and selective Fe³⁺ sensing in aqueous solution could be established. Under optimum conditions, the extent of the fluorescence quenching of prepared CDs strongly depended on the Fe³⁺ ions over a wide concentration range 1.0–100.0 μM with a detection limit (3σ/k) of 0.3 μM. Furthermore, the quantitative determination of Fe³⁺ ions in environmental water samples was realized.     

A ‘turn‐on’ fluorescent chemosensor for quantification of serum albumin in aqueous solution at neutral pH

A fluorescent chemosensor 1 (4‐diethylamino‐2′‐hydroxychalcone) for detecting serum albumin with long‐wavelength emission, good selectivity and facile synthesis was reported. Upon the addition of bovine serum albumin (BSA) to an aqueous solution of 1 at neutral pH, a ‘turn‐on’ fluorescence response was observed at 596 nm based on a hydrophobic binding mode between 1 and BSA. A linear range of 0.10–1.00 mg/mL and a detection limit of 9.1 µg/mL for BSA were obtained, respectively. Moreover, 1 was successfully applied to detect BSA in real bovine serum samples with satisfied recovery and accuracy, which suggested that 1 could serve as a valid and effective fluorescent chemosensor for quantification of BSA. Copyright © 2015 John Wiley & Sons, Ltd.     

A turn‐on indole‐based sensor for hydrogen sulfate ion

A simple indole‐based receptor 1 was prepared by a simple Schiff‐base reaction of 1H‐indole‐3‐carbaldehyde with ethane 1,2‐diamine and its fluoroionophoric properties toward anions were investigated. Indole‐based receptor 1 acts as a selective turn‐on fluorescent sensor for HSO₄^? in methanol among a series of tested anions. Fluorescence spectroscopy, ultraviolet and nuclear magnetic resonance imaging support that the HSO₄^– indeed interacted with imine nitrogen and the proton of nitrogen in indole ring. Copyright © 2013 John Wiley & Sons, Ltd.     

‘Turn‐on’ fluorescent chemosensors based on naphthaldehyde‐2‐pyridinehydrazone compounds for the detection of zinc ion in water at neutral pH

A series of naphthaldehyde‐2‐pyridinehydrazone derivatives were discovered to display interesting ‘turn‐on’ fluorescence response to Zn²⁺ in 99% water/DMSO (v/v) at pH 7.0. Mechanism study indicated that different substituent groups in the naphthaldehyde moiety exhibited significant influence on the detection of Zn²⁺. The electron rich group resulted in longer fluorescence wavelengths but smaller fluorescence enhancement for Zn²⁺. Among these compounds, 1 showed the highest fluorescence enhancement of 19‐fold with the lowest detection limit of 0.17 μmol/L toward Zn²⁺. The corresponding linear range was at least from 0.6 to 6.0 μmol/L. Significantly, 1 showed an excellent selectivity toward Zn²⁺ over other metal ions including Cd²⁺.     

Enzyme‐triggered fluorescence turn‐off/turn‐on of carbon dots for monitoring β‐glucosidase and its inhibitor in living cells

Energy transfer engineering based on fluorescent probes for directly sensing enzyme activities are in great demand as enzyme‐mediated transformations, which are central to all biological processes. Here, a fluorescence carbon dot (CD)‐based assay exhibiting selective responses to the quantitation of β‐glucosidase and the effect of its inhibitor was developed. The most common substrate, para‐nitrophenyl‐β‐d ‐glucopyranoside (pNPG) was hydrolyzed by β‐glucosidase to release p‐nitrophenol (pNP), which can efficiently quench fluorescence of CDs via an inner filter effect and electron transfer. However, in the presence of inhibitors of β‐glucosidase, the fluorescence intensity gradually recovered as the concentration of inhibitors increased. Therefore, the enzyme‐triggered fluorescence turn‐off/turn‐on of specific CDs successfully achieved sensitive detection of β‐glucosidase and monitored the effect of its inhibitors. This new strategy was applied to detect β‐glucosidase and monitor β‐glucosidase inhibitor in hepatoma cells using cell imaging. All results suggest that the new method is sensitive and promising for use in cancer diagnosis and treatment.     

脱色希瓦氏菌S12的铁还原性能研究

从印染废水中分离得到了一株具有染料脱色功能的希瓦氏菌脱色新种。该菌能在厌氧条件下利用Fe^3＋作为末端电子受体获得能量,支持细胞生长。在pH8．0．温度30℃。柠檬酸铁800mg／L,乳酸钠2g／L,酵母抽提物0．5g／L的条件下,培养8h的过程中,菌体细胞量的增长完全与Fe^3＋的还原发展趋向一致。同时考察了碳氮源、乳酸钠、酵母抽提物、pH值和温度等方面对该菌株的生长和铁还原特性的影响。结果表明,菌体生长以LB为最好,以葡萄糖和乳酸钠为碳源时对铁还原有利。在酵母抽提物浓度4g／L范围内,菌体生长量和铁还原率随着酵母抽提物浓度的提高而提高。当乳酸钠为6g／L时,S12菌体生长量和铁还原率达到最佳。柠檬酸铁浓度为800mg／L时菌体生长量和铁还原率最高。在起始pH6-8的范围内,菌株S12的生长随着pH升高而升高,这也是菌株S12进行铁还原的最佳pH范围。菌株S12在温度范围20℃-40℃内均可生长和进行铁还原,而以30℃时最佳。     

Rational Construction of Self‐Standing Sulfur‐Doped Fe2O3 Anodes with Promoted Energy Storage Capability for Wearable Aqueous Rechargeable NiCo‐Fe Batteries

Aqueous rechargeable Ni‐Fe batteries featuring an ultra‐flat discharge plateau, low cost, and outstanding safety characteristics show promising prospects for application in wearable energy storage. In particular, fiber‐shaped Ni‐Fe batteries will enable textile‐based energy supply for wearable electronics. However, the development of fiber‐shaped Ni‐Fe batteries is currently challenged by the performance of fibrous Fe‐based anode materials. In this context, this study describes the fabrication of sulfur‐doped Fe₂O₃ nanowire arrays (S‐Fe₂O₃ NWAs) grown on carbon nanotube fibers (CNTFs) as an innovative anode material (S‐Fe₂O₃ NWAs/CNTF). Encouragingly, first‐principle calculations reveal that S‐doping in Fe₂O₃ can dramatically reduce the band gap from 2.34 to 1.18 eV and thus enhance electronic conductivity. The novel developed S‐Fe₂O₃ NWAs/CNTF electrode is further demonstrated to deliver a very high capacity of 0.81 mAh cm^?2 at 4 mA cm^?2. This value is almost sixfold higher than that of the pristine Fe₂O₃ NWAs/CNTF electrode. When a cathode containing zinc‐nickel‐cobalt oxide (ZNCO)@Ni(OH)₂ NWAs heterostructures is used, 0.46 mAh cm^?2 capacity and 67.32 mWh cm^?3 energy density are obtained for quasi‐solid‐state fiber‐shaped NiCo‐Fe batteries, which outperform most state‐of‐the‐art fiber‐shaped aqueous rechargeable batteries. These findings offer an innovative and feasible route to design high‐performance Fe‐based anodes and may inspire new development for the next‐generation wearable Ni‐Fe batteries.     

Formation of fluorescent carbon nanodots from kitchen wastes and their application for detection of Fe3+

This work reports a scalable synthesis of water‐dispersible fluorescent carbon nanodots based on the simple hydrothermal method (180 °C for 6 h) of kitchen wastes (grape peel for example). We discuss the feasibility of synthesis from kitchen wastes both experimentally and theoretically, and the as‐prepared nanodots have high selectivity for Fe³⁺ ions based on fluorescence quenching which is due to the complexes between nanodots and metal ions. Copyright © 2014 John Wiley & Sons, Ltd.     

Heterocyclic fluorescent Schiff base chemosensors for the detection of Fe(III) and Cu(II) ions

Two new Schiff bases were synthesized from 1-(2,4-dihydroxyphenyl)ethanone and pyridine derivatives. Both compounds were characterized using infrared, UV–Vis., ¹H NMR, ¹³C NMR and mass spectral studies. Density functional theory (DFT) calculations were performed for both the Schiff bases with 6-31G(d, p) as the basis set. Vibrational frequencies calculated using the theoretical method were in good agreement with the experimental values. Both the Schiff bases were highly fluorescent in nature. The cation-recognizing profile of the compounds was investigated in aqueous methanol medium. The Schiff base 4-(1-(pyridin-4-ylimino)ethyl)benzene-1,3-diol (PYEB) was found to interact with Fe(III) and Cu(II) ions, whereas the Schiff base 4,4′-((pyridine-2,3-diylbis(azanylylidene))bis(ethan-1-yl-1-ylidene))bis(benzene-1,3-diol) (PDEB) was found to detect Cu(II) ions. The mechanism of recognition was established as combined excited state intramolecular proton transfer (ESIPT)–chelation-enhanced fluorescence (CHEF) effect and chelation-enhanced quenching (CHEQ) process for the detection of Fe(III) and Cu(II) ions, respectively. The stability constant of the metal complexes formed during the sensing process was determined. The limit of detection for Fe(III) and Cu(II) ions with respect to Schiff base PYEB was found to be 1.64 × 10⁻⁶ and 2.16 × 10⁻⁷ M, respectively. With respect to Schiff base PDEB, the limit of detection for Cu(II) ion was found to be 4.54 × 10⁻⁴ M. The Cu(II) ion sensing property of the Schiff base PDEB was applied in bioimaging studies for the detection of HeLa cells.     

Self‐Assembled BiFeO3‐ε‐Fe2O3 Vertical Heteroepitaxy for Visible Light Photoelectrochemistry

Self‐assembled vertical heterostructure with a high interface‐to‐volume ratio offers tremendous opportunities to realize intriguing properties and advanced modulation of functionalities. Here, a heterostructure composed of two visible‐light photocatalysts, BiFeO₃ (BFO) and ε‐Fe₂O₃ (ε‐FO), is designed to investigate its photoelectrochemical performance. The structural characterization of the BFO‐FO heterostructures confirms the phase separation with BFO nanopillars embedded in the ε‐FO matrix. The investigation of band structure of the heterojunction suggests the assistance of photoexcited carrier separation, leading to an enhanced photoelectrochemical performance. The insights into the charge separation are further revealed by means of ultrafast dynamics and electrochemical impedance spectroscopies. This work shows a delicate design of the self‐assembled vertical heteroepitaxy by taking advantage of the intimate contact between two phases that can lead to a tunable charge interaction, providing a new configuration for the optimization of photoelectrochemical cell.     

Phenothiazine–rhodamine‐based colorimetric and fluorogenic ‘turn‐on' sensor for Zn2+ and bioimaging studies in live cells

A phenothiazine–rhodamine (PTRH) fluorescent dyad was synthesized and its ability to selectively sense Zn²⁺ ions in solution and in in vitro cell lines was tested using various techniques. When compared with other competing metal ions, the PTRH probe showed the high selectivity for Zn²⁺ ions that was supported by electronic and emission spectral analyses. The emission band at 528 nm for the PTRH probe indicated the ring closed form of PTRH, as for Zn²⁺ ion binding to PTRH, the λ_em get shift to 608 nm was accompanied by a pale yellow to pink colour (under visible light) and green to pinkish red fluorescence emission (under UV light) due to ring opening of the spirolactam moiety in the PTRH ligand. Spectral overlap of the donor emission band and the absorption band of the ring opened form of the acceptor moiety contributed towards the fluorescence resonance energy transfer ON mechanism for Zn²⁺ ion detection. The PTRH sensor had the lowest detection limit for Zn²⁺, found to be 2.89 × 10^?8 M. The sensor also demonstrated good sensing application with minimum toxicity for in vitro analyses using HeLa cells.     

A simply synthesized biphenyl substituted piperidin‐4‐one for the fluorescence chemosensing of Cd2+

Ion‐induced change in fluorescence is a straight‐forward method for detection of toxic metal ions showing immediate response. Cadmium ions are toxic to the environment. We report in this paper a piperidine‐4‐one‐based fluorescent chemosensor of Cd²⁺ ions, designed and synthesized by a simple method. The compound is characterized using infra‐red (IR) and ¹H–NMR spectral techniques. The chemosensor showed Cd²⁺ ion selectivity and sensitivity in aqueous solution. The stoichiometry and the binding constants were determined using fluorescence spectroscopy. Piperidine‐4‐one shows a 1:1 stoichiometric binding to Cd²⁺. The limit of detection of Cd²⁺ was reported.     

The NADH-dependent Fe3+-chelate reductases of tomato roots

The NADH-dependent Fe³⁺-chelate reductase (NFCHR) of tomato (Lycopersicon esculentum L.) roots, a strategy I species, was investigated. The Fe³⁺-citrate reductase (FeCitR) assay was strongly inhibited by p-hydroxymercuribenzoic acid (PHMB); moreover, the inhibitor was found to be more specific to the FeCitR assay than to the Fe³⁺-EDTA reductase assay, which was catalyzed by at least another reductase of 46 kDa. After high-speed centrifugation of tomato root membranes, high FeCitR activities were detected in pellets and lower activities in supernatants. After two-phase partitioning of microsomes, FeCitR activity (91 nmol · min⁻¹ · mg⁻¹) was less active in the upper phase (plasma membrane) than in the lower phase (277 nmol · min⁻¹ · mg⁻¹). However, only the activity of the plasma-membrane-associated NFCHR (FeCitR) was significantly enhanced (2.6-fold) in iron-deficient tomato plants, whereas that of NFCHR in non-plasma-membrane rich fractions was unaffected by this treatment. The NFCHR obtained from lysophosphatidylcholine-solubilized plasma membrane was present as a 200-kDa protein complex following fast protein liquid chromatography on Superdex 200, or as a 28-kDa form following Blue Sepharose CL-6B chromatography. Both preparations were more active following iron starvation. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis showed that the 28-kDa protein purified from solubilized tomato microsomes or supernatant fractions by a final Mono Q step consisted of a single band of 32 kDa. Tomato root NFCHR resembled the NFCHR of maize (a strategy II plant, P Bagnaresi and P Pupillo, 1995, J Exp Bot 46: 1497–1503) in several properties: relative molecular mass, hydrophilicity, chromatographic behaviour, sensitivity to mercurials, specificity for electron donors and acceptors (e.g. cytochrome c), and a ferricyanide reductase-to-FeCitR ratio of 2.5. Preincubation with NADH partially protected NFCHR from PHMB-induced inactivation. Our data show that strategy I and II plants seem to share similar NFCHR proteins, which appear to belong to the cytochrome b ₅ reductase flavoprotein group. Received: 6 November 1996 / Accepted: 21 January 1997