Study on the removal of pesticide in agricultural run off by granular activated carbon

In this batch study, the adsorption of malathion by using granular activated carbon with different parameters due to the particle size, dosage of carbons, as well as the initial concentration of malathion was investigated. Batch tests were carried out to determine the potential and the effectiveness of granular activated carbon (GAC) in removal of pesticide in agricultural run off. The granular activated carbon; coconut shell and palm shells were used and analyzed as the adsorbent material. The Langmuir and Freundlich adsorption isotherms models were applied to describe the characteristics of adsorption behavior. Equilibrium data fitted well with the Langmuir model and Freundlich model with maximum adsorption capacity of 909.1 mg/g. The results indicate that the GAC could be used to effectively adsorb pesticide (malathion) from agricultural runoff.     

Removal of hexavalent chromium using distillery sludge

Batch mode experiments were conducted to study the removal of hexavalent chromium from aqueous and industrial effluent using distillery sludge. Effects of pH, contact time, initial concentration and adsorbent dosage on the adsorption of Cr(VI) were studied. The data obeyed Langmuir and Freundlich adsorption isotherms. The Langmuir adsorption capacity was found to be 5.7 mg/g. Freundlich constants K(f) and n were 2.05 [mg/g(L/mg)(n)] and 3.9, respectively. Desorption studies indicated the removal of 82% of the hexavalent chromium. The efficiency of adsorbent towards the removal of chromium was also tested using chromium-plating wastewater.     

Adsorption of Methylene Blue Dye on Pure and Carbonized Water Weeds

The influence of process variables in batch adsorption has been used to assess the removal of methylene blue dye from aqueous solution using pure and carbonized biomasses of water hyacinth and water spinach. Dried leaves of the water weeds were carbonized at temperature up to 750°C. The optimum removal of dye was achieved at pH 10, 30°C, and 55 min at a dye concentration of 10 mg/L. In an attempt to describe the adsorption process, the equilibrium isotherm for each adsorbent was determined using Langmuir and Freundlich adsorption isotherm models. Maximum adsorption capacities based on the Langmuir model for pure and carbonized water hyacinth were (mg/g) 7.05 and 2.07, respectively, whereas those of pure and carbonized water spinach were 1.25 and 5.32, respectively. It was observed that the equilibrium data were well fit by both the Freundlich and Langmuir isotherms as R ² > .97. This study demonstrates that the two waterweeds are effective, environmentally friendly, and inexpensive biomaterials for the removal of color from industrial effluents.     

Removal of emulsified food and mineral oils from wastewater using surfactant modified barley straw

Barley straw, an agricultural waste, was chemically modified and evaluated for the removal of emulsified oils from aqueous solution. The chemical modification was performed using NaOH and a cationic surfactant, hexadecylpyridinium chloride monohydrate (CPC). The surface textural and chemical properties of the surfactant modified barley straw (BMBS) were characterized by N₂ adsorption, FT-IR, SEM and water soluble mineral content. The adsorption tests were carried out in batch adsorption system for removal of standard mineral oil (SMO) and canola oil (CO) from water. For both emulsified oils in wastewater, adsorption was found to be strongly related with solution pH. The isotherm study indicated that emulsified oil adsorption on BMBS could be fitted well with the Langmuir model other than Freundlich model. The maximum adsorption capacity for CO and SMO at 25 °C determined from the Langmuir isotherm is 613.3 and 584.2 mg g⁻¹, respectively. Desorption tests in water solution show that oil is strongly bonded with adsorbent and desorption is only about 1–2% in 24 h.     

POTENTIAL USE OF LEAF BIOMASS,ARAUCARIA HETEROPHYLLA FOR REMOVAL OF Pb+2

The present investigation attempt to analyze the biosorption behavior of novel biosorbent, Araucaria heterophylla (green plant) biomass, for removal of Pb⁺² from solution as the function of initial metal ion concentration, pH, temperature, sorbent dosage and biomass particle size. The maximum biosorption was found to be 95.12% at pH 5 and biosorption capacity (q_e) of Cd⁺² is 9.643 mg/g. The Langmuir and Freundlich equilibrium adsorption isotherms were studied and observed that Freundlich model is best fit than the Langmuir model with correlation coefficient of 0.9927. Kinetic studies indicated that the biosorption process of Cd⁺² followed well pseudo second order model with R² 0.999. The process is exothermic and, spontaneous. The chemical functional groups –OH, CH₂ stretching vibrations, C?O of alcohol, C?O of amide, P?O stretching vibrations, –CH, were involved in the process. The XRD pattern of the A. heterophylla was found to be mostly amorphous in nature. The SEM studies showed Pb⁺² biosorption on selective grains of the biosorbent. It was concluded that A. heterophylla leaf powder can be used as an effective, low cost, and environmentally friendly biosorbent for the removal of Pb⁺² from aqueous solution.     

Adsorptive removal of Pb(II) by activated carbon prepared from Spartina alterniflora: Equilibrium,kinetics and thermodynamics

Low-cost activated carbon was prepared from Spartina alterniflora by phosphoric acid activation for the removal of Pb(II) from dilute aqueous solution. The effect of experimental parameters such as pH, initial concentration, contact time and temperature on the adsorption was studied. The obtained data were fitted with the Langmuir and Freundlich equations to describe the equilibrium isotherms. The kinetic data were fitted with the Lagergren-first-order, pseudo-second-order and Elovich models. It was found that pH played a major role in the adsorption process. The maximum adsorption capacity for Pb(II) on S. alterniflora activated carbon (SAAC) calculated from Langmuir isotherm was more than 99 mg g⁻¹. The optimum pH range for the removal of Pb(II) was 4.8–5.6. The Freundlich isotherm model was found to best describe the experimental data. The kinetic rates were best fitted to the pseudo-second-order model. Thermodynamic study showed the adsorption was a spontaneous exothermic process.     

Scavenging Rhodamine B dye using moringa oleifera seed pod

Moringa oliferia seed pod was modified using orthophosphoric acid (H₃PO₄) and used as adsorbent for sequestering Rhodamine B (Rh-B) dye from aqueous solution. The acid-modified adsorbent (MOSPAC) was characterized using Scanning Electron microscopy (SEM), Fourier Transform Infra Red (FTIR), Energy Dispersive X-ray (EDX), pH point of zero charge (pH_pzc) and Boehm Titration (BT) techniques, respectively. Operational parameters such as contact time, initial dye concentration, adsorbent dosage, pH and solution temperature were studied in batch process. Optimum dye adsorption was observed at pH 3.01. Equilibrium adsorption data was tested data using four different isotherm models: Langmuir, Freundlich, Temkin and Dubinin-Radushkevich. Langmuir isotherm model fitted most with maximum monolayer adsorption capacity of 1250 mg g^–1. Pseudo-second-order kinetic model provided the best correlation for the experimental data. Thermodynamic study showed that the process is endothermic, spontaneous and feasible. MOSPAC is an effective adsorbent for the removal of RhB dye from aqueous solutions.     

Microwave assisted thermal treatment of defective coffee beans press cake for the production of adsorbents

Defective coffee press cake, a residue from coffee oil biodiesel production, was evaluated as an adsorbent for removal of basic dyes (methylene blue – MB) from aqueous solutions. The adsorbent was prepared by microwave treatment, providing a significant reduction in processing time coupled to an increase in adsorption capacity in comparison to conventional carbonization in a muffle furnace. Batch adsorption tests were performed at 25 °C and the effects of particle size, contact time, adsorbent dosage and initial solution pH were investigated. Adsorption kinetics was better described by a second-order model. The experimental adsorption equilibrium data were fitted to Langmuir, Freundlich and Tempkin adsorption models, with Langmuir providing the best fit. The results presented in this study show that microwave activation presents great potential as an alternative method in the production of adsorbents.     

Ni (II) adsorption onto Chrysanthemum indicum: Influencing factors,isotherms, kinetics,and thermodynamics

The study explores the adsorption potential of Chrysanthemum indicum biomass for nickel ion removal from aqueous solution. C. indicum flowers in raw (CIF-I) and biochar (CIF-II) forms were used as adsorbents in this study. Batch experiments were conducted to ascertain the optimum conditions of solution pH, adsorbent dosage, contact time, and temperature for varying initial Ni(II) ion concentrations. Surface area, surface morphology, and functionality of the adsorbents were characterized by Brunauer, Emmett, and Teller (BET) surface analysis, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and Fourier transform infrared spectroscopy (FTIR). Adsorption kinetics were modeled using pseudo-first order, pseudo-second order, Elovich, intraparticle diffusion, Bangham's, and Boyd's plot. The equilibrium data were modeled using Langmuir, Freundlich, Temkin, and Dubinin–Radushkevich (D-R) isotherm models. Experimental data provided the best fit to pseudo-second-order kinetic model and Langmuir isotherm model for the adsorption of Ni(II) ion on both CIF-I and CIF-II with maximum adsorption capacities of 23.97 and 44.02 mg g^?1, respectively. Thermodynamic analysis of the data proved the process to be spontaneous and endothermic in nature. Desorption studies were conducted to evaluate the possibility of reusing the adsorbents. Findings of the present study provide substantial evidence for the use of C. indicum flower as an eco-friendly and potential adsorbent for the removal of Ni(II) ions from aqueous solution.     

Biosorption of hexavalent chromium from aqueous solution by a tropical basidiomycete BDT-14 (DSM 15396)

Summary A tropical white-rot basidiomycete, BDT-14 (DSM 15396) was investigated for its chromium (VI) biosorption potential from an aqueous solution. Pre-treatment of fungal biomass with acid resulted in 100% metal adsorption compared to only 26.64% adsorption without any pre-treatment. Chromium adsorption was a rapid process at early exposure resulting in 60% chromium removal within the first 2 h of exposure. An increase in biomass showed an increase in the total metal ions adsorption but a decrease in specific uptake of metal ions. The concentrations of chromium had a pronounced effect on the rate of adsorption. The adsorption efficiency was 100% when the initial Cr (VI) concentration was 100 mg l⁻¹ with 1,000 mg biomass. Only 47.5% adsorption was observed with 500 mg l⁻¹ Cr (VI) concentration. The adsorption data fit well with the Langmuir and Freundlich isotherm models. Comprehensive characterization of parameters indicates BDT−14 biomass as a promising material for Cr (VI) adsorption.     

Preparation and Characterization of Chemically Modified Silk Cotton Hull Activated Carbon and Its Effects on Cd(II) Removal from Aqueous Solutions

The novel biosorbent silk cotton hull, an agrowaste material, has been successfully utilized for the removal of cadmium(II) from aqueous solutions. The adsorption of cadmium onto three kinds of activated biosorbent has been studied: modified by concentrated sulfuric acid alone (AC), a mixture of concentrated sulfuric acid and hydrogen peroxide (AC1), and a mixture of concentrated sulfuric acid and ammonium persulfate (AC2). The adsorption studies were carried out to optimize the process parameters such as pH, adsorbent dosage, contact time, and initial metal ion concentration. Maximum metal removal was observed at pH 7.0 with a contact time of 90 min at stirring speed of 200 rpm with an adsorbent dosage of 4.0 g L^?1. The sorption isotherms were studied using the Langmuir, Freundlich, and Tempkin isotherm models. The maximum adsorption capacities were 100.00, 142.86, and 142.87 mg g^?1 for AC, AC1, and AC2, respectively. Accordingly, the surface modification of the activated carbons AC1 and AC2 enhanced cadmium removal greatly. The experiments demonstrated that the removal of metal ions followed the pseudo-second-order kinetic model. The sorption mechanism is discussed in terms of the activated surface properties. A relationship between the oxygen content and sorption was found in this novel material. Desorption experiments were carried out using hydrochloric acid with a view to generate the spent adsorbent and to recover the adsorbed metal ions.     

Fluoroquinolone resistance contributing mechanisms and genotypes of ciprofloxacin- unsusceptible Pseudomonas aeruginosa strains in Iran: emergence of isolates carrying qnr/aac(6)-Ib genes

International Microbiology - Fluoroquinolones (FQs) including ciprofloxacin (CIP) are key antibiotics for the treatment of Pseudomonas aeruginosa infections, but resistance to FQs is developing as...     

Chemical modification of chitosan by tetraethylenepentamine and adsorption study for anionic dye removal

To utilize the contribution of introduced amino groups to the adsorption of an anionic dye (eosin Y), a batch adsorption system was applied to study the adsorption of eosin Y from aqueous solution by tetraethylenepentamine (TEPA) modified chitosan (TEPA–CS). Experiments were carried out as a function of particle size, initial pH, agitation rate, adsorbent dosage, agitation period, temperature and initial concentration of eosin Y. The Langmuir and Freundlich models were used to fit the adsorption isotherms. From the values of correlation coefficients (R²), it was observed that the experimental data fit very well to the Langmuir model, giving a maximum sorption capacity of 292.4 mg/g at 298 K. Kinetic studies showed that the kinetic data were well described by the pseudo-second-order kinetic model. The thermodynamic study revealed negative value of enthalpy change (ΔH°) and free energy change (ΔG°), indicating spontaneous and endothermic nature of the adsorption of eosin Y on to TEPA–CS.     

Biosorption of Lead from Industrial Wastewater Using Chrysophyllum albidum Seed Shell

The shell of the seed of Chrysophyllum albidum carbon was used to adsorb lead (Pb) from aqueous solution, the sorption process with respect to its equilibria and kinetics as well as the effects of pH, contact time, adsorbent mass, adsorbate concentration, and particle size on adsorption were also studied. The most effective pH range was found to be between 4.5 and 5 for the sorption of the metal ion. The first-order rate equation by Lagergren was tested on the kinetic data and the adsorption process followed first-order rate kinetics. Isotherm data were analyzed for possible agreement with the Langmuir and Freundlich adsorption isotherms; the Freundlich and Langmuir models for dynamics of metal ion uptake proposed in this work fitted the experimental data reasonably well. However, equilibrium sorption data were better represented by Langmuir model than Freundlich. The adsorption capacity calculated from Langmuir isotherm was 72.1 mg Pb (II) g^{- 1} at initial pH of 5.0 at 30°C for the particle size of 1.00 to 1.25 mm with the use of 2.0 g/100 ml adsorbent mass. The structural features of the adsorbent were characterized by Fourier transform infrared (FTIR) spectrometry; the presence of hydroxyl, carbonyl, amide, and phosphate groups confirms the potential mechanism adsorption of the adsorbent. This readily available adsorbent is efficient in the uptake of Pb (II) ion in aqueous solution, thus, it could be an excellent alternative for the removal of heavy metals and organic matter from water and wastewater.     

Equilibrium and a two-stage batch adsorber design for reactive or disperse dye removal to minimize adsorbent amount

The adsorption of a reactive dye (Reactive Yellow K-4G) and a disperse dye (Disperse yellow brown S-2RFL) onto polyepicholorohydrin-dimethylamine (EPIDMA) cationic polymer modified bentonite (EPIDMA-bentonite) in batch adsorber was studied, respectively. Two equilibrium models, the Langmuir and Freundlich models were selected to follow the adsorption process. It was shown that the equilibrium experimental data for reactive dye adsorption could be well described by the Freundlich model, but for disperse dye the Langmuir model could be better. Based on the well correlated adsorption isotherm, an adsorption process design model was developed for the design of a two-stage batch adsorber to predict the minimum amount of adsorbent to achieve a specified percentage of dye removal at a given volume of wastewater effluents. The adsorption process design analysis indicated that compared with the single-stage batch adsorption, the two-stage process could significantly save adsorbent to meet the higher demands of dye removal efficiency.     

Designing chitosan based magnetic beads with conocarpus waste-derived biochar for efficient sulfathiazole removal from contaminated water

The development of a simple method to synthesize highly efficient and stable magnetic microsphere beads for sulfathiazole (STZ) removal from contaminated aqueous media was demonstrated in this study. Conocarpus (Conocarpus erectus L.) tree waste (CW) derived biochar (BC) was modified to fabricate chitosan-BC (CBC) and magnetic CBC (CBC-Fe) microsphere beads. Proximate, chemical, and structural properties of the produced adsorbents were investigated. Kinetics, equilibrium, and pH adsorption batch trials were conducted to evaluate the effectiveness of the synthesized adsorbents for STZ removal. All adsorbents exhibited the highest STZ adsorption at pH 5.0. STZ adsorption kinetics data was best emulated using pseudo-second order and Elovich models. The equilibrium adsorption data was best emulated using Langmuir, Freundlich, Redlich–Peterson, and Temkin models. CBC-Fe demonstrated the highest Elovich, pseudo-second order, and power function rate constants, as well as the highest apparent diffusion rate constant. Additionally, Langmuir isotherm predicted maximum adsorption capacity was the highest for CBC-Fe (98.67 mg g⁻¹), followed by CBC (56.54 mg g⁻¹) and BC (48.63 mg g⁻¹). CBC-Fe and CBC removed 74.5%–108.8% and 16.2%–25.6% more STZ, respectively, than that of pristine BC. π-π electron-donor–acceptor interactions and Lewis acid-base reactions were the main mechanisms for STZ removal; however, intraparticle diffusion and H-bonding further contributed in the adsorption process. The higher efficiency of CBC-Fe for STZ adsorption could be due to its magnetic properties as well as stronger and conducting microsphere beads, which degraded the STZ molecules through generation of HO^• radicals.     

Biosorption of di(2-ethylhexyl)phthalate by seaweed biomass

Samples of various Sargassum species were collected in the Hong Kong marine environment and used for studies on biosorption of di(2-ethylhexyl)phthalate (DEHP). Batch adsorption experiments were carried out to determine the removal capacity and removal efficiency of the biosorbents. The DEHP removal ability was similar among beached seaweed and three freshly collected Sargassum species. Different physico-chemical factors were evaluated in order to enhance the performance of the biosorbents. Under optimized conditions (25 mg biomass, initial pH 4, 25 °C, 40 mg L^–1 DEHP), the mean removal capacity of beached seaweed and Sargassum siliquastrum was 5.68 and 6.54 mg g^–1, respectively. Examination of the Langmuir and Freundlich adsorption isotherms showed that the biosorption phenomenon by these biosorbents could well be described by these models. Desorption of DEHP was also assessed with methanol, which showed the most satisfactory desorbing ability. Further study in multiple adsorption–desorption of DEHP by the biosorbents demonstrated the reusability of both beached seaweed and S. siliquastrum for biosorption of DEHP.     

Biosorption of trivalent and hexavalent chromium from aqueous systems using shelled Moringa oleifera seeds

Abstract

The present study explores the sorption properties of shelled Moringa oleifera seeds (SMOS) for removal of two environmentally important oxidation states of chromium (trivalent and hexavalent) from an aqueous system on the laboratory scale. Sorption studies reveal the optimum conditions for the removal of 81.02%; Cr (III) and 88.15% Cr (VI) as follows: biomass dosage (4.0 g), metal concentration [25mg/L for Cr (III); 50mg/L for Cr (VI)], contact time (40 minutes) at pH 6.5 and 2.5 respectively. The adsorption data were found to fit well both the Freundlich and Langmuir isotherms. Characterization of the seed powder by FTIR showed the clear presence of amino acid moieties having both positively charged amino and negatively charged carboxylic groups and confirmed that biosorption involves amino acid-chromium interactions. SEM studies of native and exhausted [Cr(III) and Cr(VI)] treated SMOS revealed large spherical clusters having a pore area of 8.66 µm² in the case of native SMOS while dense agglomerated etched dendrite type morphology have a pore area of 0.80 µm² in Cr (III) and 0.78 µm² in Cr (VI) treated SMOS The spent biosorbent was regenerated and found to be effectively reusable for four cycles.     

Manganese adsorption by sediment in Wadi Tafna,Algeria

The removal of manganese from aqueous solution by sediment in Wadi Tafna, north-western Algeria, was investigated under batch conditions in 2003. Kinetic data equilibrium removal isotherms were measured at 20 °C. The influence of different experimental parameters, such as contact time, manganese concentration and sediment mass on the removal kinetics of manganese was studied. The content of carbonate in sediment increased the adsorption rate, indicating the active phase towards manganese cations. The process followed pseudo-second-order kinetics. Manganese uptake by sediment was quantitatively evaluated using sorption isotherms. In order to describe the adsorption isotherm mathematically, the experimental data of the removal equilibrium were analysed with Langmuir and Freundlich models revealing that the equilibrium data were perfectly represented using both isotherms.