Locations of hypochlorite oxidation in corn starches varying in amylose content

The general oxidation mechanism by hypochlorite on starch has been well studied, but the information on the distribution of the oxidation sites within starch granules is limited. This study investigated the locations where the oxidation occurred within corn starch granules varying in amylose content, including waxy corn starch (WC), common corn starch (CC), and 50% and 70% high-amylose corn starch (AMC). Oxidized corn starches were surface gelatinized by 13 M LiCl at room temperature to different extents (approximately 10%, 20%, 30%, and 40%). The surface-gelatinized remaining granules were separated and studied for structural characteristics including carboxyl content, amylose content, amylopectin chain-length distribution, thermal properties, and swelling properties. Oxidation occurred mostly at the amorphous lamellae. More carboxyl groups were found at the periphery than at the core of starch granules, which was more pronounced in oxidized 70% AMC. More amylose depolymerization from oxidation occurred at the periphery of CC. For WC and CC, amylopectin long chains (>DP 36) were more prone to depolymerization by oxidation. The gelatinization properties as measured by differential scanning calorimetry also supported the changes in amylopectin fine structure from oxidation. Oxidized starches swelled to a greater extent than their unmodified counterparts at all levels of surface removal. This study demonstrates that the locations of oxidation and physicochemical properties of oxidized starches are affected by the molecular arrangement within starch granules.     

Structural characteristics and physicochemical properties of oxidized corn starches varying in amylose content

The effects of amylose content on the extent of oxidation and the distribution of carboxyl groups in hypochlorite-oxidized corn starches were investigated. Corn starches including waxy corn starch (WC), common corn starch (CC), and 50% and 70% high-amylose corn starches (AMC) were oxidized with NaOCl at three concentrations (0.8%, 2%, and 5%). Carboxyl and carbonyl content of oxidized starches increased with increasing NaOCl concentration. High-AMC (70%) had slightly higher carboxyl and carbonyl contents at 0.8% NaOCl, whereas WC had significantly higher carboxyl and carbonyl contents at 2% and 5% NaOCl levels. Carbohydrate profiles by high-performance size-exclusion chromatography indicate that amylose was more susceptible to depolymerization than amylopectin. Degradation of amylopectin long chains (DP >24) was more pronounced in WC and CC than in AMCs. The crystalline lamellae of WC started to degrade at 2% NaOCl, but those of the other corn starches remained intact even at 5% NaOCl level according to X-ray crystallinity. By using anion-exchange chromatography for separation and size-exclusion chromatography for characterization, carboxyl groups were found to be more concentrated on amylopectin than on amylose, particularly in AMCs. Oxidation decreased gelatinization temperature and enthalpy with WC showing the most decrease and 70% AMC showing the least. The gelatinization enthalpy of 50% AMC decreased significantly faster than those of CC and 70% AMC after 0.8% oxidation. Retrogradation of amylopectin slightly increased after oxidation with increasing oxidation level. The peak viscosities of oxidized WC and CC were higher than those of their native counterparts at 0.8% NaOCl, but this increase was not observed in AMCs. The setback viscosities of 2% NaOCl-oxidized 50% and 70% AMCs were much higher than those of the unmodified counterparts. The extent of oxidation and physicochemical properties of oxidized starches varied greatly with the amylase:amylopectin ratio of corn starches. Amylose was suggested to play an important role in controlling the oxidation efficiency.     

Sweet wheat

The major components of storage starch are amylose and amylopectin, and in wheat, both an amylose-free mutant lacking granule-bound starch synthase I and a high-amylose mutant lacking starch synthase IIa have been produced recently. Here, we report the production of an amylose-free/ high-amylose double mutant. This double mutant has kernel and carbohydrate characteristics that are remarkably different than those of either single mutant, including a dramatically shrunken seed shape. Surprisingly, the double mutant has maltose and sucrose levels that are high enough to make it worthy of being called "sweet wheat".     

The influence of amylose and amylopectin characteristics on gelatinization and retrogradation properties of different starches

Physico-chemical properties of starch from wheat, rye, barley (waxy, high-amylose and normal-amylose), waxy maize, pea and potato (normal-amylose and high-amylopectin) were studied. Emphasis was given to the amylose (total, apparent and lipid-complexed) and amylopectin characteristics as well as to the gelatinization and retrogradation properties measured using differential scanning calorimetry. The total amylose content varied from ca. 1 % for waxy maize to 37% for high-amylose barley. The amylopectin characteristics were determined by high-performance size-exclusion chromatography after debranching with isoamylase. The weight-average degree of polymerization ( _w) was 26, 33 and 27 for the A-, B-, and C-type starches, respectively. In general, the potato starches exhibited the highest retrogradation enthalpies and the cereal starches the lowest, while the pea starch showed an intermediate retrogradation enthalpy. The data were analysed by principal component analysis (PCA). The _w showed positive correlation to the melting interval, the peak minimum, the offset temperatures of the retrogradation-related endotherm as well as to the gelatinization and retrogradation enthalpies. However, the high-amylose barley retrograded to a greater extent than the other cereal starches, despite low _w (24). The amylose content was negatively correlated to the onset and the peak minimum temperatures of gelatinization.     

Structural and physicochemical characterisation of rye starch

The gelatinisation, pasting and retrogradation properties of three rye starches isolated using a proteinase-based procedure were investigated and compared to those of wheat starch isolated in a comparable way. On an average, the rye starch granules were larger than those of wheat starch. The former had very comparable gelatinisation temperatures and enthalpies, but slightly lower gelatinisation temperatures than wheat starch. Under standardised conditions, they retrograded to a lesser extent than wheat starch. The lower gelatinisation temperatures and tendencies of the rye starches to retrograde originated probably from their higher levels of short amylopectin (AP) chains [degree of polymerisation (DP) 6–12] and their lower levels of longer chains (DP 13–24) than observed for wheat starch. The rapid visco analysis differences in peak and end viscosities between the rye starches as well as between rye and wheat starches were at least partly attributable to differences in the levels of AP short chains and in average amylose molecular weight. The AP average chain lengths and exterior chain lengths were slightly lower for rye starches, while the interior chain lengths were slightly higher than those for wheat starch.     

Production of very-high-amylose potato starch by inhibition of SBE A and B

High-amylose starch is in great demand by the starch industry for its unique functional properties. However, very few high-amylose crop varieties are commercially available. In this paper we describe the generation of very-high-amylose potato starch by genetic modification. We achieved this by simultaneously inhibiting two isoforms of starch branching enzyme to below 1% of the wild-type activities. Starch granule morphology and composition were noticeably altered. Normal, high-molecular-weight amylopectin was absent, whereas the amylose content was increased to levels comparable to the highest commercially available maize starches. In addition, the phosphorus content of the starch was increased more than fivefold. This unique starch, with its high amylose, low amylopectin, and high phosphorus levels, offers novel properties for food and industrial applications.     

Structural characterization of wheat starch granules differing in amylose content and functional characteristics

Small-angle X-ray scattering (SAXS) together with several complementary techniques, such as differential scanning calorimetry and X-ray diffraction, have been employed to investigate the structural features that give diverse functional properties to wheat starches (Triticum aestivum L.) within a narrow range of enriched amylose content (36–43%). For these starches, which come from a heterogeneous genetic background, SAXS analysis of duplicate samples enabled structural information to be obtained about their lamellar architecture where differences in lamellar spacing among samples were only several tenths of nanometer. The SAXS analysis of these wheat starches with increased amylose content has shown that amylose accumulates in both crystalline and amorphous parts of the lamella. Using waxy starch as a distinctive comparison with the other samples confirmed a general trend of increasing amylose content being linked with the accumulation of defects within crystalline lamellae. We conclude that amylose content directly influences the architecture of semi-crystalline lamellae, whereas thermodynamic and functional properties are brought about by the interplay of amylose content and amylopectin architecture.     

Sorption of Monoterpenoids and Sesquiterpenoids by Natural Polysaccharides

Sorption of terpenoids (essential oil components) from aqueous solutions by six types of native food starches was studied by capillary gas chromatography. Sorption of volatile substances did not depend on amylose content in starch and specific surface of its granules. The degree of sorption was maximum (86%) for corn starch containing 25–28% amylose and decreased in the following order: tapioca starch (77%) > potato starch (74%) > wheat starch (70%) > high-amylose corn starch (58%) > amylopectin corn starch (57%). Amylopectin corn starch differed from other starches in the mechanism of sorption and selectivity to compounds with various functional groups.     

Sorption of mono- and sesquiterpenes by natural polysaccharides

Sorption of terpenoids (essential oil components) from aqueous solutions by six types of native food starches was studied by capillary gas chromatography. Sorption of volatile substances did not depend on amylose content in starch and specific surface of its granules. The degree of sorption was maximum (86%) for corn starch containing 25-28% amylose and decreased in the following order: tapioca starch (77%) > potato starch (74%) > wheat starch (70%) > high-amylose corn starch (58%) > amylopectin corn starch (57%). Amylopectin corn starch differed from other starches in the mechanism of sorption and selectivity to compounds with various functional groups.     

Rate studies of the amylose–iodine reaction in unfractionated starch samples of various plant origin

The initial rate of the fast reaction among amylose, iodine, and iodide ions was studied in unfractionated corn, potato, rice, wheat, and arrowroot starches. It was found that the reaction followed the same rate equation as the one established in a previous study using pure amylose fractions containing no amylopectin. There were significant differences, however, among the rate constants of the various starches investigated. These variations were explained in terms of the different average molecular weights of the amylose fractions of these starches. Since whole potato starch indicated a rate constant well within the fange of those of pure amylose fraction (obtained from the same potato starch samples), it was concluded, that amylopectin did not interfere significantly with the rate of the complexation reaction.     

Structure function relationships of transgenic starches with engineered phosphate substitution and starch branching

Potato tuber starch was genetically engineered in the plant by the simultaneous antisense suppression of the starch branching enzyme (SBE) I and II isoforms. Starch prepared from 12 independent lines and three control lines were characterised with respect to structural and physical properties. The lengths of the amylopectin unit chains, the concentrations of amylose and monoesterified phosphate were significantly increased in the transgenically engineered starches. Size exclusion chromatography with refractive index detection (SEC-RI) indicated a minor decrease in apparent molecular size of the amylose and the less branched amylopectin fractions. Differential scanning calorimetry (DSC) revealed significantly higher peak temperatures for gelatinisation and retrogradation of the genetically engineered starches whereas the enthalpies of gelatinisation were lower. Aqueous gels prepared from the transgenic starches showed increased gel elasticity and viscosity. Principle component analysis (PCA) of the data set discriminated the control lines from the transgenic lines and revealed a high correlation between phosphate concentration and amylopectin unit chain length. The PCA also indicated that the rheological characteristics were primarily influenced by the amylose concentration. The phosphate and the amylopectin unit chain lengths had influenced primarily the pasting and rheological properties of the starch gels.     

Determination of the botanical origin of starch using direct potentiometry and PCA

A new approach for the determination of the botanical origin of starch is presented based on the formation of starch-triiodide complexes. The starch samples were extracted from wheat (Srpanjka), potato, maize, rye (Barun), barley (Conduct), rice, tapioca and a commercial modified starch. The amylose/amylopectin ratios of starches, among various other properties, differ between starches of different botanical origins. Triiodide ions bind characteristically to the amylose and amylopectin of the starch depending on the starch's origin. The new technique includes direct potentiometric measurements of the response of free triiodide ions in starch-triiodide solutions where the data is analysed by principal component analysis (PCA). PCA gave graphical results for statistical differentiation between starches of different botanical origins.     

Estimation and fractionation of the essentially unbranched (amylose) and branched (amylopectin) components of starches with concanavalin A

Conditions have been devised for the quantitative precipitation of the branched fraction in starches by concanavalin A and the enzymic estimation of the - -glucan in this and the soluble components. For some starches, such as those from cereal and high-amylose pea seeds, the percentage of branched fraction determined by this procedure was higher than that calculated by deducting from one hundred the apparent amylose content as measured by potentiometric iodine titration, suggesting a method for estimating the content of material having an atypical structure in the whole starch. The procedure has been adapted to provide a preparative method of separating amylose and amylopectin fractions. It efficiently separated these in starches that cannot be fully fractionated by complexing with 1-butanol, such as those from high-amylose pea seeds and tobacco leaves.     

Preparation of clear noodles with mixtures of tapioca and high-amylose starches

Ways to simulate the making of clear noodles from mung bran starch were investigated by studying the molecular structures of mung bean and tapioca starches. Scanning electron micrographs showed that tapioca starch granules were smaller than those of mung bean starch. X-ray diffraction patterns of mung bean and tapioca starch were A- and C_A-patterns, respectively. Iodine affinity studies indicated that mung bean starch contained 37% of apparent amylose and tapioca starch contained 24%. Gel permeation chromatograms showed that mung bean amylopectin had longer peak chain-length of long-branch chains (DP 40) than that of tapioca starch (DP 35) but shorter peak chain-length of short-branch chains (DP 16) than that of tapioca starch (DP 21). P-31 n.m.r. spectroscopy showed that both starches contained phosphate monoesters, but only mung bean starch contained phospholipids. Physical properties, including pasting viscosity, gel strength, and thermal properties (gelatinization), were determined. The results of the molecular structure study and physical properties were used to develop acceptable products using mixtures of cross-linked tapioca and high-amylose maize starches. Tapioca starch was cross-linked by sodium trimetaphosphate (STMP) with various reaction times, pH values, and temperatures. The correlation between those parameters and the pasting viscosity were studied using a visco/amylograph. Starches, cross-linked with 0.1% STMP, pH 11.0, 3.5 h reaction time at 25, 35, and 45°C (reaction temperature), were used for making noodles. High-amylose maize starch (70% amylose) was mixed at varying ratios (9, 13, 17, 28, 37, and 44%) with the cross-linked tapioca starches. Analysis of the noodles included: tensile strength, water absorption, and soluble loss. Noodle sensory properties were evaluated using trained panelists. Noodles made from a mixture of cross-linked tapioca starch and 17% of a high-amylose starch were comparable to the clear noodles made from mung bean starch.     

Effect of acid–alcohol treatment on the molecular structure and physicochemical properties of maize and potato starches

The molecular structure and physicochemical properties of acid–alcohol treated maize and potato starches (0.36% HCl in methanol at 25 °C for 1–15 days) were investigated. The yields of the modified starches were ranging from 91 to 100%. The average granule size of modified starches decreased slightly. The solubility of starches increased with the increase of treatment time, and the pasting properties confirmed the high solubility of modified starches. The gelatinization temperatures and range of gelatinization increased with the increase of treatment time except T_o (onset temperature) of maize starch. Molecular structures of modified starches suggested the degradation of starches occurred mostly within the first 5 days of treatment, and degradation rate of potato starch was higher than maize starch both in amylopectin and in amylose. Maize starch was found less susceptible to acid–alcohol degradation than potato starch.     

Waterlogging and simulated acid rain after anthesis deteriorate starch quality in wheat grain

The synthesis and accumulation of starch is greatly affected by environmental stress. Wheat grown in the downstream area of the Yangtze River is easily subjected to stress of waterlogging and acid rain. In order to probe the effect of waterlogging and acid rain on yield and starch characteristic, we used winter wheat cultivars of Yangmai 16 (more resistant) and Wennong 17 (relatively sensitive) to sole stress of acid rain or waterlogging and to their combinations during grain filling. The responses of grain yield, the physiochemical properties and morphology of starch granules in endosperm to the stresses were investigated. Compared with CT (control), grain yield in Wennong 17 were significantly decreased by both pH 4.0 acid rain and pH 2.5 acid rain, while in Yangmai 16 only by pH 2.5 acid rain. Waterlogging combined with acid rain significantly reduced grain weight and grain yield in both wheat cultivars. Acid rain, waterlogging and their combination depressed activities of ADP glucose pyrophosphorylase and soluble starch synthase (SSS) in grains of both cultivars. Acid rain and waterlogging damaged endosperm cell structure and caused abnormal starch granules. Starch granules at maturity became fragile and failed to keep in shape and some granules were even totally submerged in the protein matrix and other tissue under acid rain and waterlogging. Content of amylopectin and amylopectin/amylose ratio was also decreased, while content of amylose was increased under acid rain and waterlogging. As a result, swelling power and most viscosity parameters decreased, while the pasting temperature increased in both cultivars due to stresses. In sum, acid rain and waterlogging and their combination damaged cell structure and depressed synthesis of amylopectin, and led to the formation of abnormal fragile starch granules, and finally reduced grain weight and then yield, and deteriorated starch quality.     

Structural parameters of amylopectin clusters and semi-crystalline growth rings in wheat starches with different amylose content

Small-angle X-ray scattering (SAXS) and scanning electron microscopy (SEM) were used to investigate the internal structure of wheat starch granules with different amylose content. Different approaches were used for treatment (interpretation) of SAXS data to assess the values of structural parameters of amylopectin clusters and the size of crystalline and amorphous lamella in different wheat starches. The average values of the semi-crystalline growth rings thickness in starches have been determined and the relationship between structural characteristics and thermodynamic melting parameters is discussed.     

The size and shape of amylopectin: a study using analytical ultracentrifugation

Starch was isolated from a range of wheat cultivars grown under various conditions. The starches were known to produce pastes having contrasting rheological properties when heated. Solutions of the starch in dimethyl sulphoxide were investigated by analytical ultracentrifugation. Sedimentation coefficients and normalized weight-frequency distributions of limiting sedimentation-coefficients were determined. The sedimentation-coefficient data confirmed the weight-average molar mass of amylopectin in dimethyl sulphoxide to be ∼10⁷, irrespective of the source of the starch. The sedimentation-coefficient values were also combined with diffusion-coefficient data and evaluated according to hydrodynamic theory, this indicated that amylopectin has a flat-sheet or disc-like structure with semi-major and semi-minor axes of 45 and 1.2 nm, respectively. The distributions of sedimentation coefficients of the amylopectin samples were all similar, being unimodal, symmetrical, and having peak-width half-heights of ∼60 S. The amylopectin obtained after removal of amylose by chemical fractionation was shown to be representative of the total amylopectin in starch.     

Characterization of barley starches of waxy, normal, and high amylose varieties

Four varieties of barley starches, W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier, were isolated from barley seeds. Apparent and absolute amylose contents, molecular size distributions of amylose and amylopectin, amylopectin branch-chain-length distributions, and Naegeli dextrin structures of the starches were analyzed. W.B. Merlin amylopectin had the longest detectable chain length of DP 67, whereas glacier, high amylose glacier and high amylose hull-less glacier amylopectins had the longest detectable chain length of DP 82, 79, and 78, respectively. All the four starches displayed a substantially reduced proportion of chains at DP 18–21. Amylopectins of high amylose varieties did not show significantly larger proportions of long chains than that of normal and waxy barley starch. Onset gelatinization temperatures of all four barley starches ranged from 55.0 to 56.5°C. Absolute amylose contents of W.B. Merlin, glacier, high amylose glacier, and high amylose hull-less glacier were 9.1, 29.5, 44.7, and 43.4%, respectively; phospholipid contents were 0.36, 0.78, 0.79, and 0.97%, respectively.     

Determination of the maximum water solubility of eight native starches and the solubility of their acidic-methanol and -ethanol modified analogues

The maximum water solubilities of eight native starches from potato, shoti, tapioca, maize, waxy maize, amylomaize-7, wheat, and rice and their acid-methanol and acid-ethanol modified analogues have been determined. Maximum solubilities of 18.7 and 17.4 mg/mL were obtained for waxy maize and tapioca and 12.4 mg/mL for potato and maize starches by autoclaving 220 mg/10 mL at 121 degrees C; 8.7 mg/mL was obtained for shoti starch by stirring in 85:15 (v/v) Me(2)SO-H(2)O at 20 degrees C; and 7.0 and 5.2mg/mL for rice and amylomaize-7 starches by stirring in 1M NaOH at 20 degrees C. The acid-alcohol treated starches were 4-9 times more soluble than their native starches. The compositions of the solubilized starches had, in general, much higher ratios of amylose to amylopectin than the ratios in their native granules. A major exception to this was the acid-methanol treated potato, shoti, and rice starches that had much lower ratios of amylose to amylopectin than the ratios in their granules.