Microbial community developments and biomass characteristics in membrane bioreactors under different organic loadings

Microbial community developments and biomass characteristics (concentration, particle size, extracellular polymeric substances (EPS), and membrane fouling propensity) were compared when three MBRs were fed with the synthetic wastewater at different organic loadings. Results showed that the bacterial communities dynamically shifted in different ways and the EPS displayed dissimilar profiles under various organic loadings, which were associated with the ratios of food to microorganism and dissolved oxygen levels in the MBRs. The membrane fouling tendency of biomass in the low-loading MBR (0.57 g COD/L day) was insignificantly different from that in the medium-loading MBR (1.14 g COD/L day), which was apparently lower than that in the high-loading MBR (2.28 g COD/L day). The membrane fouling propensity of biomass was strongly correlated with their bound EPS contents, indicating cake layer fouling (i.e., deposition of microbial flocs) was predominant in membrane fouling at a high flux of 30 L/m² h.     

Linking microbial community structure to membrane biofouling associated with varying dissolved oxygen concentrations

In order to elucidate how dissolved oxygen (DO) concentration influenced the generation of extracellular polymeric substance (EPS) and soluble microbial products (SMP) in mixed liquor and biocake, 16S rDNA fingerprinting analyses were performed to investigate the variation of the microbial community in an aerobic membrane bioreactor (MBR). The function of microbial community structure was proved to be ultimately responsible for biofouling. Obvious microbial community succession from the subphylum of Betaproteobacteria to Deltaproteobacteria was observed in biocake. High concentration of EPS in biocake under the low DO concentration (0.5 mg L⁻¹) caused severe biofouling. The correlation coefficient of membrane fouling rate with EPS content in biocake (0.9941-0.9964) was much higher than that in mixed liquor (0.6689-0.8004).     

Effect of increasing the surface area of primary sludge on anaerobic digestion at low temperature

Two sets of reactors were operated at 15 °C and at sludge retention times (SRTs) of 65 days and 30 days, respectively. Each set was operated at six different mixing velocities. Shear forces provided by mixing affected particle size distribution and resulted in different sludge surface areas. The aim was to investigate the effect of increasing primary sludge surface area on anaerobic digestion at low temperature. The maximum surface areas at the applied mixing velocities were 5926 cm²/cm³of sludge and 4672 cm²/cm³ of sludge at SRTs of 65 days and 30 days, respectively. The corresponding calculated methanogenesis were 49% and 15% at SRTs of 65 days and 30 days, respectively. Maximum total solids (TS) reductions were 26% and 11% at 65 days and 30 days SRTs, respectively. Lipase activity increased with increasing SRT and sludge surface area. Results clearly showed that increasing sludge surface area improved sludge digestion at 15 °C.     

Fractionation of proteins and carbohydrates of extracellular polymeric substances in a membrane bioreactor system

The major operational problem associated with membrane bioreactors (MBR) is membrane fouling, for which extracellular polymeric substances (EPS) are primarily responsible. In this work both the soluble and bound EPS (i.e. SMP and EPS) produced in an MBR system operating under sludge retention times (SRT) of 10, 15, 20 and 33 days were fractionized by means of membranes having variable molecular weight cutoffs (300 kDa, 100 kDa, 10 kDa & 1 kDa). The results show that increasing the SRT leads to a reduction of SMP and EPS and that these reductions are more pronounced for the SRTs in the range 10–20 days. This reduction is more significant for carbohydrates than for proteins. The decrease of SMP and EPS with increasing SRT from 10 to 20 days led to a significant decrease of the level of fouling. The further increase of SRT to 33 days did not significantly impact on the level of fouling as the SMP and EPS concentrations did not change much.     

Influence of solids retention time on membrane fouling: characterization of extracellular polymeric substances and soluble microbial products

The objective of this study was to investigate the influence of solids retention time (SRT) on membrane fouling and the characteristics of biomacromolecules. Four identical laboratory-scale membrane bioreactors (MBRs) were operated with SRTs for 10, 20, 40 and 80 days. The results indicated that membrane fouling occurred faster and more readily under short SRTs. Fouling resistance was the primary source of filtration resistance. The modified fouling index (MFI) results suggested that the more ready fouling at short SRTs could be attributed to higher concentrations of soluble microbial products (SMP). Fourier transform infrared (FTIR) spectra indicated that the SRT had a weak influence on the functional groups of the total extracellular polymeric substances (TEPS) and SMP. However, the MBR under a short SRT had more low-molecular-weight (MW) compounds (<1 kDa) and fewer high-MW compounds (>100 kDa). Aromatic protein and tryptophan protein-like substances were the dominant groups in the TEPS and SMP, respectively.     

Horizontal transfer of antibiotic resistance genes in a membrane bioreactor

Growing attention has been paid to the dissemination of antibiotic resistance genes (ARGs) in wastewater microbial communities. The application of membrane bioreactors (MBRs) in wastewater treatment is becoming increasingly widespread. We hypothesized that the transfer of ARGs among bacteria could occur in MBRs, which combine a high density of bacterial cells, biofilms, and antibiotic resistance bacteria or ARGs. In this study, the transfer discipline and dissemination of the RP4 plasmid in MBRs were investigated by the counting plate method, the MIDI microorganism identification system, and quantitative polymerase chain reaction (qPCR) techniques. The results showed that the average transfer frequency of the RP4 plasmid from the donor strain to cultivable bacteria in activated sludge was 2.76 × 10⁻⁵ per recipient, which was greater than the transfer frequency in wastewater and bacterial sludge reported previously. In addition, many bacterial species in the activated sludge had received RP4 by horizontal transfer, while the genera of Shewanella spp., Photobacterium spp., Pseudomonas spp., Proteus spp., and Vibrio spp. were more likely to acquire this plasmid. Interestingly, the abundance of the RP4 plasmid in total DNA remained at high levels and relatively stable at 10⁴ copies/mg of biosolids, suggesting that ARGs were transferred from donor strains to activated sludge bacteria in our study. Thus, the presence of ARGs in sewage sludge poses a potential health threat.     

The influenced of PAC, zeolite, and Moringa oleifera as biofouling reducer (BFR) on hybrid membrane bioreactor of palm oil mill effluent (POME)

The main objective of this work was to determine the effectiveness of various biofouling reducers (BFRs) to operational condition in hybrid membrane bioreactor (MBR) of palm oil mill effluent (POME). A series of tests involving three bench scale (100 L) hybrid MBR were operated at sludge retention times (SRTs) of 30 days with biofouling reducer (BFR). Three different biofouling reducers (BFRs) were powdered actived carbon (PAC), zeolite (Ze), and Moringa oleifera (Mo) with doses of 4, 8 and 12 g L⁻¹ respectively were used. Short-term filtration trials and critical flux tests were conducted. Results showed that, all BFRs successfully removed soluble microbial products (SMP), for PAC, Ze, and Mo at 58%, 42%, and 48%, respectively. At their optimum dosages, PAC provided above 70% reductions and 85% in fouling rates during the short-term filtration and critical flux tests.     

The impact of different operating conditions on membrane fouling and EPS production

The main goal of this research was to investigate how different factors influence membrane fouling. The impact of the different concentrations of activated sludge and the amount of extracellular polymer substances (EPS) were monitored. Two pilot plants with submerged membrane modules (hollow fiber and flat sheet) were operated and the raw wastewater was used.Humic substances were identified as the major components of EPS in the activated sludge (more than 34%) in both pilot plants. As the basic constituent in permeate, humic substances were identified as the most dominant components in the effluent (61%) in both pilot plants. Conversely, proteins were mostly analyzed in permeate and supernatant below the detection limit. The total amount of EPS [mg g⁻¹ (VSS)] was similar for concentrations of activated sludge 6, 10 and 14 g L⁻¹. Carbohydrates were identified as the component of EPS which tends most to clog membranes.     

Correlation between fouling propensity of soluble extracellular polymeric substances and sludge metabolic activity altered by different starvation conditions

Soluble extracellular polymeric substances (EPSs) cause membrane fouling in membrane bioreactors (MBRs), correlated with MBR sludge characteristics. Effects of F/M ratios on the evolution of soluble EPSs, fouling propensity of supernatants, and sludge metabolic activity were measured in this study in a two-period sequencing batch reactor (SBR). The experimental results show that fouling propensity was directly correlated with soluble-EPS concentration and composition. Sludge that had entirely lost active cells by long-term starvation released 64.4 ± 0.9 mg/L of humic acids, which caused a rapid increase in membrane resistance (40.67 ± 2.24 × 10¹¹ m⁻¹) during fouling tests. During short-term starvation, induced by incubation at a normal to low F/M ratio of 0.05 d⁻¹, sludge can use previously secreted utilization-associated products (UAPs) to maintain endogenous respiration. Therefore, the strategies of accumulating sludge and prolonging sludge retention time in MBRs may create long-term starvation and promote membrane fouling.     

New insights into membrane fouling in a submerged anaerobic membrane bioreactor based on characterization of cake sludge and bulk sludge

A laboratory-scale submerged anaerobic membrane bioreactor (SAnMBR) treating thermomechanical pulping whitewater was operated for over 7 months to investigate and compare the characteristics of cake sludge and bulk sludge during stable state operation period. Serial analysis showed that cake sludge had a smaller particle size distribution (PSD), much higher specific filtration resistance (1.34 × 10¹⁴ m/kg), 1.5 times higher bound EPS and significantly different microbial community as compared with bulk sludge. Further analysis indicated that small flocs, bound EPS and inorganic materials play important role in cake formation process. The formed cake layer was found to have a heterogeneous structure. The results obtained in this study indicated that cake formation process started from attachment of small flocs and/or specific bacterial clusters which colonize the surface of the membrane and provide enhanced conditions that allow for cake formation to progress.     

Microbial population dynamics and proteomics in membrane bioreactors with enzymatic quorum quenching

Quorum sensing gives rise to biofilm formation on the membrane surface, which in turn causes a loss of water permeability in membrane bioreactors (MBRs) for wastewater treatment. Enzymatic quorum quenching was reported to successfully inhibit the formation of biofilm in MBRs through the decomposition of signal molecules, N-acyl homoserine lactones (AHLs). The aim of this study was to elucidate the mechanisms of quorum quenching in more detail in terms of microbial population dynamics and proteomics. Microbial communities in MBRs with and without a quorum quenching enzyme (acylase) were analyzed using pyrosequencing and compared with each other. In the quorum quenching MBR, the rate of transmembrane pressure (TMP) rise-up was delayed substantially, and the proportion of quorum sensing bacteria with AHL-like autoinducers (such as Enterobacter, Pseudomonas, and Acinetobacter) also decreased in the entire microbial community of mature biofilm in comparison to that in the control MBR. These factors were attributed to the lower production of extracellular polymeric substances (EPS), which are known to play a key role in the formation of biofilm. Proteomic analysis using the Enterobacter cancerogenus strain ATCC 35316 demonstrates the possible depression of protein expression related to microbial attachments to solid surfaces (outer membrane protein, flagellin) and the agglomeration of microorganisms (ATP synthase beta subunit) with the enzymatic quorum quenching. It has been argued that changes in the microbial population, EPS and proteins via enzymatic quorum quenching could inhibit the formation of biofilm, resulting in less biofouling in the quorum quenching MBR.     

Influence of membrane fouling reducers (MFRs) on filterability of disperse mixed liquor of jet loop bioreactors

The effects of membrane fouling reducers (MFRs) (the cationic polyelectrolyte (CPE) and FeCI₃) on membrane fouling were studied in a lab-scale jet loop submerged membrane bioreactor (JL-SMBR) system. The optimum dosages of MFRs (CPE dosage = 20 mg g⁻¹MLSS, FeCI₃ dosage = 14 mg g⁻¹MLSS) were continuously fed to JL-SMBR system. The soluble and bound EPS concentrations as well as MLSS concentration in the mixed liquor of JL-SMBR were not changed substantially by the addition of MFRs. However, significant differences were observed in particle size and relative hydrophobicity. Filtration tests were performed by using different membrane types (polycarbonate (PC) and nitrocellulose mixed ester (ME)) and various pore sizes (0.45-0.22-0.1 μm). The steady state fluxes (J_ss) of membranes increased at all membranes after MFRs addition to JL-SMBR. The filtration results showed that MFRs addition was an effective approach in terms of improvement in filtration performance for both membrane types.     

EPS and SMP dynamics at different heights of a submerged anaerobic membrane bioreactor (SAMBR)

Membrane bioreactors (MBR) technology for wastewater offers many advantages over conventional technologies such as high effluent quality, less footprint and others. The main disadvantage of membrane bioreactors (MBR) is related to membrane fouling, which is mainly caused by extracellular polymeric substance (EPS) and soluble microbial products (SMP). This research studied EPS and SMP dynamics at different heights of a submerged anaerobic membrane bioreactor (SAMBR). The SAMBR was operated under two organic loading rates (OLR) (0.79 and 1.56 kg/m³ d) and was fed with synthetic wastewater with glucose as the carbon source. The results showed percentages of chemical oxygen demand (COD) removal above 95% and the highest COD removal rates were observed at the bottom of the reactor (>83%) for both OLR. The EPS showed a stratification with highest quantities in the supernatant. For the SMP the highest concentration was in the bottom of SAMBR where utilization predominated associated products whereas in the SAMBR supernatant predominated biomass associated products. The OLR change led to a significant increase in SMP accumulation but not in EPS. These facts showed that EPS and SMP dynamic in the SAMBR seemed to be mainly influenced by biological activity, total suspended solids concentration and substrate composition.     

Optimization, purification, characterization and antioxidant activity of an extracellular polysaccharide produced by Paenibacillus polymyxa SQR-21

The optimization, purification and characterization of an extracellular polysaccharide (EPS) from a bacterium Paenibacillus polymyxa SQR-21 (SQR-21) were investigated. The results showed that SQR-21 produced one kind of EPS having molecular weight of 8.96 × 10⁵ Da. The EPS was comprised of mannose, galactose and glucose in a ratio of 1.23:1.14:1. The ratio of monosaccharides and glucuronic acid was 7.5:1. The preferable culture conditions for EPS production were pH 6.5, temperature 30 °C for 96 h with yeast extract and galactose as best N and C sources, respectively. The maximum EPS production (3.44 g L⁻¹) was achieved with galactose 48.5 g L⁻¹, Fe³⁺ 242 μM and Ca²⁺ 441 μM. In addition, the EPS showed good superoxide scavenging, flocculating and metal chelating activities while moderate inhibition of lipid peroxidation and reducing activities were determined. These results showed the great potential of EPS produced by SQR-21 to be used in industry in place of synthetic compounds.     

The correlation between biofilm biopolymer composition and membrane fouling in submerged membrane bioreactors

Biofouling, the combined effect of microorganism and biopolymer accumulation, significantly reduces the process efficiency of membrane bioreactors (MBRs). Here, four biofilm components, alpha-polysaccharides, beta-polysaccharides, proteins and microorganisms, were quantified in MBRs. The biomass of each component was positively correlated with the transmembrane pressure increase in MBRs. Proteins were the most abundant biopolymer in biofilms and showed the fastest rate of increase. The spatial distribution and co-localization analysis of the biofouling components indicated at least 60% of the extracellular polysaccharide (EPS) components were associated with the microbial cells when the transmembrane pressure (TMP) entered the jump phase, suggesting that the EPS components were either secreted by the biofilm cells or that the deposition of these components facilitated biofilm formation. It is suggested that biofilm formation and the accumulation of EPS are intrinsically coupled, resulting in biofouling and loss of system performance. Therefore, strategies that control biofilm formation on membranes may result in a significant improvement of MBR performance.     

Biomass characteristics and membrane aeration: toward a better understanding of membrane fouling in submerged membrane bioreactors (MBRs)

Fouling in submerged membrane bioreactors (MBRs) was studied under different operating conditions and with varying biomass characteristics. Fouling rates were determined using a flux-step method for seven biomass conditions with mixed liquor solids concentrations ranging from 4.3 to 13.5 g x l(-1), six permeate fluxes (5.5, 11.0, 16.5, 22.0, 27.5, and 33.0 l x m(-2) x h(-1)), and three membrane airflow velocities (0.07, 0.10, and 0.13 m x s(-1)). Statistical analysis was used to specify the degree of influence of each of the biomass characteristics (solids concentration, dewaterability, viscosity, particle size distribution, concentrations of protein and carbohydrate in the soluble microbial products, SMP, and extracellular polymer substances, EPS), the permeate flux and the membrane aeration velocity on the membrane fouling rate. Among all these variables, only the permeate flux, the solids concentration (correlated to the viscosity and the dewaterability), the carbohydrate concentration in the EPS, and the membrane aeration velocity were found to affect the fouling rate. The permeate flux had the greatest effect. A transitional permeate flux was observed between 16.5 and 33 l x m(-2) x h(-1), below which no significant fouling was observed regardless of the biomass characteristics, the permeate flux, and the membrane aeration velocity.     

Microbial transformation of biomacromolecules in a membrane bioreactor: implications for membrane fouling investigation

Background

The complex characteristics and unclear biological fate of biomacromolecules (BMM), including colloidal and soluble microbial products (SMP), extracellular polymeric substances (EPS) and membrane surface foulants (MSF), are crucial factors that limit our understanding of membrane fouling in membrane bioreactors (MBRs).

Findings

In this study, the microbial transformation of BMM was investigated in a lab-scale MBR by well-controlled bioassay tests. The results of experimental measurements and mathematical modeling show that SMP, EPS, and MSF had different biodegradation behaviors and kinetic models. Based on the multi-exponential G models, SMP were mainly composed of slowly biodegradable polysaccharides (PS), proteins (PN), and non-biodegradable humic substances (HS). In contrast, EPS contained a large number of readily biodegradable PN, slowly biodegradable PS and HS. MSF were dominated by slowly biodegradable PS, which had a degradation rate constant similar to that of SMP-PS, while degradation behaviors of MSF-PN and MSF-HS were much more similar to those of EPS-PN and EPS-HS, respectively. In addition, the large-molecular weight (MW) compounds (>100 kDa) in BMM were found to have a faster microbial transformation rate compared to the small-MW compounds (<5 kDa). The parallel factor (PARAFAC) modeling of three-dimensional fluorescence excitation-emission matrix (EEM) spectra showed that the tryptophan-like PN were one of the major fractions in the BMM and they were more readily biodegradable than the HS. Besides microbial mineralization, humification and hydrolysis could be viewed as two important biotransformation mechanisms of large-MW compounds during the biodegradation process.

Significance

The results of this work can aid in tracking the origin of membrane foulants from the perspective of the biotransformation behaviors of SMP, EPS, and MSF.     

Selective oxidation of sulfide catalysed by Cu complex of a triazamacrocyclic ligand with carbamoyl pendant arms

Copper(II) complex with a new ligand 1,4,7-tris(carbamoylethyl)-1,4,7-triazacyclononane (L) has been synthesized and characterized by elemental analysis, FT-IR, ES-MS, UV-Vis and cyclic voltammetry. Determined by X-ray analysis, the crystal structure shows the metal center is six-coordinated. The compound can catalyze the oxygenation of ethyl phenyl sulfide (EPS) utilizing H₂O₂ under ambient conditions. EPS was converted to the corresponding sulfoxide and sulfone step by step which was confirmed by ¹H NMR spectra. The existence of sulfoxide and sulfone was identified by GC-MS. The gradually disappearance of EPS’s ultraviolet absorption at 290 nm was significantly correlated with the rates of sulfide consumption. The initial reaction rate during the first 3 h is consistent with the first-order law in substrate concentration. The averaged pseudo-first-order rate constant is calculated to be (2.25 ± 0.42) × 10⁻³ min⁻¹ at 25 °C and (4.44 ± 0.17) × 10⁻³ min⁻¹ at 30 °C. The oxidation product is almost sulfoxide by choosing the molar concentrations of Cu complex (2% of substrate) and H₂O₂ (seven times as much as substrate).     

Simultaneous Congo red decolorization and electricity generation in air-cathode single-chamber microbial fuel cell with different microfiltration, ultrafiltration and proton exchange membranes

Different microfiltration membrane (MFM), proton exchange membrane (PEM) and ultrafiltration membranes (UFMs) with different molecular cutoff weights of 1 K (UFM-1K), 5 K (UFM-5K) and 10 K (UFM-10K) were incorporated into air-cathode single-chamber microbial fuel cells (MFCs) which were explored for simultaneous azo dye decolorization and electricity generation to investigate the effect of membrane on the performance of the MFC. Batch test results showed that the MFC with an UFM-1K produced the highest power density of 324 mW/m² coupled with an enhanced coulombic efficiency compared to MFM. The MFC with UMF-10K achieved the fastest decolorization rate (4.77 mg/L h), followed by MFM (3.61 mg/L h), UFM-5K (2.38 mg/L h), UFM-1K (2.02 mg/L h) and PEM (1.72 mg/L h). These results demonstrated the possibility of using various membranes in the system described here, and showed that UFM-1K was the best one based on the consideration of both cost and performance.     

The nitrite-oxidizing community in activated sludge from a municipal wastewater treatment plant determined by fatty acid methyl ester-stable isotope probing

Metabolically-active autotrophic nitrite oxidizers from activated sludge were labeled with ¹³C-bicarbonate under exposure to different temperatures and nitrite concentrations. The labeled samples were characterized by FAME-SIP (fatty acid methyl ester-stable isotope probing). The compound cis-11-palmitoleic acid, which is the major lipid of the most abundant nitrite oxidizer in activated sludge, Candidatus Nitrospira defluvii, showed ¹³C-incorporation in all samples exposed to 3 mM nitrite. Subsequently, the lipid cis-7-palmitoleic acid was labeled, and it indicated the activity of a nitrite oxidizer that was different from the known Nitrospira taxa in activated sludge. The highest incorporation of cis-7-palmitoleic acid label was found after incubation with a nitrite concentration of 0.3 mM at 17 and 22 °C. While activity of Nitrobacter populations could not be detected by the FAME-SIP approach, an unknown nitrite oxidizer with the major lipid cis-9 isomer of palmitoleic acid exhibited ¹³C-incorporation at 28 °C with 30 mM nitrite. These results indicated flexibility of nitrite-oxidizing guilds in a complex community responding to different conditions. Labeled lipids so far not described for activated sludge-associated nitrifiers indicated the presence of unknown nitrite oxidizers in this habitat. The FAME-SIP-based information can be used to define appropriate conditions for the enrichment of nitrite-oxidizing guilds from complex samples.