Microwave‐assisted sintering synthesis of greenish‐yellow emitting Sr2SiO4:Eu2+ phosphors

Europium ion (Eu²⁺) doped Sr₂SiO₄ phosphors with greenish‐yellow emission were synthesized using microwave‐assisted sintering. The phase structure and photoluminescence (PL) properties of the obtained phosphor samples were investigated. The PL excitation spectra of the Sr₂SiO₄:Eu²⁺ phosphors exhibited a broad band in the range of 260 nm to 485 nm with a maximum at 361 nm attributed to the 5f‐4d allowed transition of the Eu²⁺ ions. Under an excitation at 361 nm, the Sr₂SiO₄:Eu²⁺ phosphor exhibited a greenish‐yellow emission peak at 541 nm with an International‐Commission‐on‐Illumination (CIE) chromaticity of (0.3064, 0.4772). The results suggest that the microwave‐assisted sintering method is promising for the synthesis of phosphors owing to the decreased sintering time without the use of additional reductive agents.     

Novel red colour emitting Ca0.995Mg2(SO4)3:0.5Eu2+ phosphor under ultraviolet,blue, and green excitation for plant growth LEDs

In the recent few years, Eu²⁺- and Mn⁴⁺-activated phosphors are widely used as potential colour converters for indoor plant cultivation lighting application due to their marvellous luminescence characteristics as well as low cost. In this investigation, we synthesized novel red colour-emitting Ca_(2−x)Mg₂(SO₄)₃:xmol% Eu²⁺ (x = 0–1.0 mol%) phosphors via a solid-state reaction method in a reducing atmosphere. The photoluminescence (PL) excitation spectra of synthesized phosphors exhibited a broad excitation band with three excitation bands peaking at 349 nm, 494 nm, and 554 nm. Under these excitations, emission spectra exhibited a broad band in the red colour region at ~634 nm. The PL emission intensity was measured for different concentrations of Eu²⁺. The maximum Eu²⁺ doping concentration in the Ca₂Mg₂(SO₄)₃ host was observed for 0.5 mol%. According to Dexter theory, it was determined that dipole–dipole interaction was responsible for the concentration quenching. The luminous red colour emission of the sample was confirmed using Commission international de l'eclairage colour coordinates. The results of PL excitation and emission spectra of the prepared phosphors were well matched with excitation and emission wavelengths of phytochrome P_R. Therefore, from the entire investigation and obtained results it was concluded that the synthesized Ca_0.995Mg₂(SO₄)₃:0.5mol%Eu²⁺ phosphor has huge potential for plant cultivation application.     

The luminescent properties and crystal structure of Sr(1.5‐x)‐(1.5y)Mg0.5SiO4:xEu2+,yCe3+ blue phosphor synthesized by co‐precipitation method

In order to improve the luminescent performance of silicate blue phosphors, Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ phosphors were synthesized using one‐step calcination of a precursor prepared by chemical co‐precipitation. The crystal structure and luminescent properties of the phosphors were analyzed using X‐ray diffraction and fluorescence spectrophotometry, respectively. Because the activated ions (Eu²⁺) can occupy two different types of sites (Sr₁ and Sr₂), the emission spectrum of Eu²⁺ excited at 350 nm contains two single bands (EM₁ and EM₂) in the wavelength range 400–550 nm, centered at 463 nm, and the emission intensity first increases and then decreases with increasing concentrations of Eu²⁺ ions. Co‐doping of Ce³⁺ ions can greatly enhance the emission intensity of Eu²⁺ by transferring its excitation energy to Eu²⁺. Because of concentration quenching, a higher substitution concentration of Ce³⁺ can lead to a decrease in the intensity. Meanwhile, the quantum efficiency of the phosphor is improved after doping with Ce³⁺, and a blue shift phenomenon is observed in the CIE chromaticity diagram. The results indicate that Sr_{(1.5‐x)‐(1.5y)}Mg_0.5SiO₄:xEu²⁺,yCe³⁺ can be used as a potential new blue phosphor for white light‐emitting diodes.     

Luminescence characteristics and X-ray-induced defects in BaFBr:Eu2+ storage phosphor

Three different approaches used to synthesize a sensitive BaFBr:Eu²⁺ X-ray storage photostimulated luminescence (PSL) phosphor at 850°C for 1 h in a reducing atmosphere are reported. The effects of F/Br and Eu concentration on photoluminescence (PL) and PSL sensitivities synthesized by the three approaches were compared. In the first recipe, BaFBr:Eu²⁺ prepared using a BaF₂, BaBr₂ and EuF₃ mixture using solid-state diffusion (Recipe I), even in a reducing atmosphere, yielded a low PL and PSL intensity due to oxygen contamination that acted as competing hole traps. When BaFBr:Eu²⁺ was prepared using ammonium bromide and ammonium fluoride by two different recipes (Recipes II and III), oxygen contamination was eliminated, resulting in enhanced PSL efficiency. The proposed PSL process in BaFBr:Eu²⁺ was consistent with the experimental results. Increased F/Br molar ratios would incorporate fluorine ion interstitials that act as hole traps accompanied by bromine ion vacancies that act as electron traps. Although two types of F centres, F(Br⁻) and F(F⁻) are possible, F(Br⁻) centres formed during X-irradiation are only vital for the PSL process. Structural, morphology, and thermoluminescence (TL) properties of the samples were also examined using XRD, field emission scanning electron microscope (FESEM), energy-dispersive X-ray spectroscopy (EDAX), and TL studies.     

Photoluminescence and thermoluminescence properties of Eu2+ doped and Eu2+,Dy3+ co‐doped Ba2MgSi2O7 phosphors

In this work, we report the preparation, characterization, comparison and luminescence mechanisms of Eu²⁺‐doped and Eu²⁺,Dy³⁺‐co‐doped Ba₂MgSi₂O₇ (BMSO) phosphors. Prepared phosphors were synthesized via a high temperature solid‐state reaction method. All prepared phosphors appeared white. The phase structure, particle size, and elemental analysis were analyzed using X‐ray diffraction (XRD), transmission electron microscopy (TEM) and energy‐dispersive X‐ray (EDX) analysis. The luminescence properties of the phosphors were investigated by thermoluminescence (TL) and photoluminescence (PL). The PL excitation and emission spectra of Ba₂MgSi₂O₇:Eu²⁺ showed the peak to be around 381 nm and 490 nm respectively. The PL excitation spectrum of Ba₂MgSi₂O₇:Eu²⁺Dy³⁺ showed the peak to be around 341 nm and 388 nm, and the emission spectrum had a broad band around 488 nm. These emissions originated from the 4f⁶ 5d¹ to 4f⁷ transition of Eu²⁺. TL analysis revealed that the maximum TL intensity was found at 5 mol% of Eu²⁺ doping in Ba₂MgSi₂O₇ phosphors after 15 min of ultraviolet (UV) light exposure. TL intensity was increased when Dy³⁺ ions were co‐doped in Ba₂MgSi₂O₇:Eu²⁺ and maximum TL intensity was observed for 2 mol% of Dy³⁺. TL emission spectra of Ba_1.95MgSi₂O₇:0.05Eu²⁺ and Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors were found at 500 nm. TL intensity increased with UV exposure time up to 15 min, then decreased for the higher UV radiation dose for both Eu doping and Eu,Dy co‐doping. The trap depths were calculated to be 0.54 eV for Ba_1.95MgSi₂O₇:0.05Eu²⁺ and 0.54 eV and 0.75 eV for Ba_1.93MgSi₂O₇:0.05Eu²⁺,0.02Dy³⁺ phosphors. It was observed that co‐doping with small amounts of Dy³⁺ enhanced the thermoluminescence properties of Ba₂MgSi₂O₇ phosphor. Copyright © 2016 John Wiley & Sons, Ltd. [Correction added on 5 April 2016, after first online publication: The following parts of the abstract have been edited for consistency. '4f65d1' has been corrected to '4f⁶ 5d¹', '4f7' has been corrected to '4f⁷', 'Ba1.95' has been corrected to 'Ba_1.95' and 'Ba1.93' has been corrected to 'Ba_1.93' respectively.]     

Photoluminescence properties of Ca2Al2O5:RE3+ (RE = Eu,Dy and Tb) phosphors for solid state lighting

Ca₂Al₂O₅:Eu³⁺, Ca₂Al₂O₅:Dy³⁺ and Ca₂Al₂O₅:Tb³⁺ phosphors were synthesized using a combustion synthesis method. The prepared phosphors were characterized by X‐ray powder diffraction for phase purity, by scanning electron microscopy for morphology, and by photoluminescence for emission and excitation measurements. The Ca₂Al₂O₅:Eu³⁺ phosphors could be efficiently excited at 396 nm and showed red emission at 594 nm and 616 nm due to ⁵D₀ → ⁷F₁ and ⁵D₀ → ⁷F₂ transitions. Dy³⁺‐doped phosphors showed blue emission at 482 nm and yellow emission at 573 nm. Ca₂Al₂O₅:Tb³⁺ phosphors showed emission at 545 nm when excited at 352 nm. Concentration quenching occurred in both Eu³⁺ and Dy³⁺phosphors at 0.5 mol%. Photoluminescence results suggested that the aluminate‐based phosphor could be a potential candidate for application in environmentally friendly based lighting technologies.     

Synthesis of AlN: Eu2+ green phosphors by a simple direct nitridation method

Eu‐doped aluminum nitride phosphors were successfully prepared using simple direct nitridation of a metallic aluminum and Eu₂O₃ powder mixture in flowing ammonia. AlN formed at reaction temperatures >900°C, and Eu³⁺ transformed into the secondary oxide phase EuAl₂O₄ in the nitridation condition. Phase pure AlN was obtained by post‐heat treatment of the nitridated product at 1600°C for 3 h in a nitrogen atmosphere, with an Eu²⁺ doping concentration < 0.5%. The phosphors exhibited broad green emission centered at 521 nm under 363 nm excitation. The luminescence of the phosphor was significantly influenced by the post‐heat treatment temperature, which affected the dissolution of Eu²⁺, phase purity, crystallinity, and particle size of the AlN host.     

Insights into the discrepant luminescence for BaSiO3:Eu2+ phosphors prepared by solid‐state reaction and precipitation reaction methods

Two synthesis routes, solid‐state reaction and precipitation reaction, were employed to prepare BaSiO₃:Eu²⁺ phosphors in this study. Discrepancies in the luminescence green emission at 505 nm for the solid‐state reaction method sample and in the yellow emission at 570 nm for the sample prepared by the precipitation reaction method, were observed respectively. A detail investigation about the discrepant luminescence of BaSiO₃:Eu²⁺ phosphors was performed by evaluation of X‐ray diffraction (XRD), photoluminescence (PL)/photoluminescence excitation (PLE), decay time and thermal quenching properties. The results showed that the yellow emission was generated from the BaSiO₃:Eu²⁺ phosphor, while the green emission was ascribed to a small amount of Ba₂SiO₄:Eu²⁺ compound that was present in the solid‐state reaction sample. This work clarifies the luminescence properties of Eu²⁺ ions in BaSiO₃ and Ba₂SiO₄ hosts.     

Synthesis and luminescent properties of novel BaGd2O4:Eu3+ scintillating phosphor

BaGd_2‐xO₄:xEu³⁺ and Ba_1‐yGd_1.79‐2yEu_0.21Na_3yO₄ phosphors were synthesized at 1300°C in air by conventional solid‐state reaction method. Phosphors were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence excitation (PLE) spectra, photoluminescence (PL) spectra and thermoluminescence (TL) spectra. Optimal PL intensity for BaGd_2‐xO₄:xEu³⁺ and Ba_1‐yGd_1.79‐2yEu_0.21Na_3yO₄ phosphors at 276 nm excitation were found to be x = 0.24 and y = 0.125, respectively. The PL intensity of Eu³⁺ emission could only be enhanced by 1.3 times with incorporation of Na⁺ into the BaGd₂O₄ host. Enhanced luminescence was attributed to the flux effect of Na⁺ ions. However, when BaGd₂O₄:Eu³⁺ phosphors were codoped with Na⁺ ions, the induced defects confirmed by TL spectra impaired the emission intensity of Eu³⁺ ions. Copyright © 2012 John Wiley & Sons, Ltd.     

Luminescence behavior of Li2Sr1‐3x/2EuxSiO4 red phosphors for LED applications

Red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ 0≤x≤0.5) phosphors were synthesized at 900°C in air by a solid‐state reaction. The synthesized phosphors were characterized by X‐ray powder diffraction, photoluminescence (PL) excitation (PLE) and PL spectra. The results from the PLE spectra suggest that the strong 394 nm excitation peak associated with the ⁵L₆ state of Eu³⁺ ions is of significance for near ultraviolet pumped white light‐emitting diodes and solid‐state lighting. It is also noted that the position of the charge transfer state of Eu³⁺ ions shifts towards the higher energy side (blue shift) by increasing the content of Eu³⁺ ions. The predominant emissions of Eu³⁺ ions under 394 nm excitation are observed at 580, 593, 614, 656 and 708 nm, which are attributed to the ⁵D₀ → ⁷F_J (J = 0, 1, 2, 3 and 4), respectively. The PL results reveal that the optimal content of the red‐emitting Li₂Sr_1‐3x/2Eu_xSiO₄ phosphors is x = 0.475. Simulation of the white light excited by 394 nm near ultraviolet light has also been carried out for its potential white light‐emitting diode applications. Copyright © 2013 John Wiley & Sons, Ltd.     

Resonant and non‐resonant energy transfer from Ce3+ → X (X = Tb3+, Eu3+ or Dy3+) in NaMgSO4F material

An inorganic NaMgSO₄F fluoride material was prepared by the wet chemical method and studied for its photoluminescence (PL) and resonant–non‐resonant energy transfer (RET and NORET) capabilities between Ce³⁺ → Tb³⁺, Ce³⁺ → Eu³⁺ and Ce³⁺ → Dy³⁺ rare earth ions. The Tb³⁺ emission for Ce³⁺ → Tb³⁺ transfers under ultraviolet (UV) wavelengths peaked at 491, 547, and 586 nm, for excitation at 308 nm due to ⁵D₄ → ⁷F_J (J = 4, 5, 6) transitions. Eu emission spectra were observed at 440 nm (Eu²⁺), 593 nm and 616 nm (Eu³⁺) recorded for different concentrations of materials, whereas Dy³⁺ emission from Ce³⁺ → Dy³⁺ transfer under UV wavelengths peaked at 485 nm and 577 nm due to ⁴F_9/2 → ⁶H_15/2 and ⁶H_13/2 transitions. The purpose of the present study is to understand the RET and NORET effects of Tb³⁺, Eu³⁺ and Dy³⁺ co‐doping in a NaMgSO₄F:Ce³⁺ luminescent material, which could be used as a green‐emitting material for lamp phosphors.     

Optical properties of Eu2+/Eu3+ mixed valence phosphor Ca2SiO2F2:Eu2+/Eu3+

The Eu²⁺/Eu³⁺ mixed valence phosphor Ca₂SiO₂F₂:Eu²⁺/Eu³⁺ was prepared using a solid‐state reaction synthesis method in a CO atmosphere, and the optical properties were investigated. The spectroscopic properties revealed that Ca²⁺ ions were occupied by both Eu²⁺ and Eu³⁺ ions in Ca₂SiO₂F₂, and both ions were able to generate their characteristic emissions. A broad 5d → 4f Eu²⁺ band at ~470 nm and narrow 4f → 4f Eu³⁺ peaks upon excitation with n‐UV light were observed. The ratio between Eu²⁺ and Eu³⁺ emissions changed regularly, and the relative intensity of the red component from Eu³⁺ became systematically stronger with increasing overall Eu content. As a result, the emission color of these phosphors can be tunable from blue to pink under n‐UV light excitation.     

Synthesis,PL characterizations and concentration quenching effect in Dy3+ and Eu3+ activated LiCaBO3 phosphor

LiCaBO₃:Dy³⁺/Eu³⁺ phosphors were synthesized by a solid‐state reaction. The synthesized materials were characterized using powder X‐ray diffraction pattern (XRD) for confirmation. All the structural parameters were calculated from the XRD data. Scanning electron microscopy (SEM) images showed rod‐like morphology. Photoluminescence (PL) emission spectra showed two emissions (484 and 577 nm) in Dy³⁺‐doped LiCaBO₃:Dy³⁺phosphors with the concentration quenching effect and the critical distance was calculated to be about 22.76 Å. LiCaBO₃:Eu³⁺ phosphor was effectively excited by a near‐UV light of 392 nm. The emission spectra exhibited the transition from ⁵D₀ level to ⁷F_J (J = 0–2) with main emission at 614 nm, which comes from the electrodipole transition because of the asymmetric point group. The quenching concentration of Eu³⁺ is about 0.2 mol%, and the critical distance was calculated to be about 38.93 Å. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of CaCN2 on the preparation of CaAlSiN3:Eu2+ phosphors

Highly efficient red‐emitting phosphors, CaAlSiN₃:Eu²⁺, were successfully prepared by the solid‐state method using calcium cyanide (CaCN₂) as the single calcium source. The influences of crystallization temperature, crystallization time, calcination mode and compounds ratio on the photoluminescent properties were investigated. The CaAlSiN₃:Eu²⁺ phosphors were obtained with 1 mol% CaCN₂ by a two‐step calcination procedure at 900°C for 2 h and subsequently at 1600°C for 8 h. The CaAlSiN₃:Eu²⁺ phosphors showed the strongest luminescent intensity at 660 nm when excited by 468 nm. With an increase in crystallization time, the maximum wavelength of the emission was shifted from 644 nm to 660 nm.     

Luminescence enhancement of (Sr1–xMx)2SiO4:Eu2+ phosphors with M (Ca2+/Zn2+) partial substitution for white light‐emitting diodes

Eu²⁺‐doped Sr₂SiO₄ phosphor with Ca²⁺/Zn²⁺ substitution, (Sr_1–xM_x)₂SiO₄:Eu²⁺ (M = Ca, Zn), was prepared using a high‐temperature solid‐state reaction method. The structure and luminescence properties of Ca²⁺/Zn²⁺ partially substituted Sr₂SiO₄:Eu²⁺ phosphors were investigated in detail. With Ca²⁺ or Zn²⁺ added to the silicate host, the crystal phase could be transformed between the α‐form and the β‐form of the Sr₂SiO₄ structure. Under UV excitation at 367 nm, all samples exhibit a broad band emission from 420 to 680 nm due to the 4f⁶5d¹ → 4f⁷ transition of Eu²⁺ ions. The broad emission band consists of two peaks at 482 and 547 nm, which correspond to Eu²⁺ ions occupying the ten‐fold oxygen‐coordinated Sr.(I) site and the nine‐fold oxygen‐coordinated Sr.(II) site, respectively. The luminescence properties, including the intensity and lifetime of Sr₂SiO₄:Eu²⁺ phosphors, improved remarkably on Ca²⁺/Zn²⁺ addition, and promote its application in white light‐emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd.     

Tunable luminescence and energy transfer in Ca3SiO4Cl2:Ce3+,Li+,Mn2+,Eu2+ phosphors

A series of color‐tunable Ca_{3–2x‐y‐z}SiO₄Cl₂ (CSC):xCe³⁺,xLi⁺,yMn²⁺,zEu²⁺ phosphors with low temperature phase structure was synthesized via the sol–gel method. An energy transfer process from Ce³⁺ to Mn²⁺ in CSC:0.01Ce³⁺,0.01Li⁺,yMn²⁺ (y = 0.03–0.09) and the mechanism was verified to be an electric dipole–dipole interaction. The Ce³⁺ and Mn²⁺ emission intensities were greatly enhanced by co‐doping Eu²⁺ ions into CSC:0.01Ce³⁺,0.01Li⁺,0.07Mn²⁺ phosphors due to competitive energy transfers from Eu²⁺/Ce³⁺ to Mn²⁺, and Ce³⁺ to Eu²⁺. Under 332 nm excitation, CSC:0.01Ce³⁺,0.01Li+,0.07Mn²⁺,zEu²⁺ (z = 0.0005–0.002) exhibited tunable emission colors from green to white with coexisting orange, green and violet‐blue emissions. These phosphors could have potential application in white light‐emitting diodes.     

Sol–gel synthesis and luminescence property of Sr4Al2O7:Re3+,R+ (Re = Eu and Dy; R = Li,Na and K) phosphors for white LEDs

Sr₄Al₂O₇:Eu³⁺ and Sr₄Al₂O₇:Dy³⁺ phosphors with alkali metal substitution were prepared using a sol–gel method. The effects of a charge compensator R on the structure and luminescence of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors were investigated in detail. Upon heating to 1400°C, the structure of the prepared samples was that of the standard phase of Sr₄Al₂O₇. Under ultraviolet excitation, all Sr₄Al₂O₇:Eu³⁺,R⁺ samples exhibited several narrow emission peaks ranging from 550 to 700 nm due to the 4f → 4f transition of Eu³⁺ ions. All Sr₄Al₂O₇:Dy³⁺,R⁺ phosphors showed two emission peaks at 492 and 582 nm, due to the ⁴F_9/2 → ⁶H_15/2 and ⁴F_9/2 → ⁶H_13/2 transitions of Dy³⁺ ions, respectively. The luminescence intensity of Sr₄Al₂O₇:Re³⁺,R⁺ (Re = Eu and Dy; R = Li, Na and K) phosphors improved markedly upon the addition of charge compensators, promoting their application in white light‐emitting diodes with a near‐ultraviolet chip.     

Enhancement of the photoluminescence and long afterglow properties of Sr2MgSi2O7:Eu2+ phosphor by Dy3+ co‐doping

Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ long afterglow phosphors were synthesized under a weak reducing atmosphere by the traditional high temperature solid state reaction method. The synthesized phosphors were characterized by powder X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDX), and photo‐, thermo‐ and mechanoluminescence spectroscopic techniques. The phase structure of the sintered phosphor was an akermanite type structure, which belongs to tetragonal crystallography. The thermoluminescence properties of these phosphors were investigated and compared. Under ultraviolet light excitation, the emission spectra of both prepared phosphors were composed of a broad emission band peaking at 470 nm. When the Sr₂MgSi₂O₇:Eu²⁺ phosphor was co‐doped with Dy³⁺, the photoluminescence (PL), afterglow and mechanoluminescence (ML) intensity were strongly enhanced. The decay graph indicated that both the sintered phosphors contained fast decay and slow decay processes. The ML intensities of Sr₂MgSi₂O₇:Eu²⁺ and Sr₂MgSi₂O₇:Eu²⁺,Dy³⁺ phosphors were increased proportionally with increasing impact velocity, a finding that suggests that these phosphors could be used as sensors to detect the stress of an object. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis and photoluminescence of EuII in barium zinc orthosilicate: a novel green color emitting phosphor for white‐LEDs

A series of Eu²⁺‐activated barium orthosilicates (BaZnSiO₄) were synthesized using a high‐temperature solid‐state reaction. A photoluminescence excitation study of Eu²⁺ shows a broad absorption band in the range of 270–450 nm, with multiple absorption peak maxima (310, 350 and 400 nm) due to 4f–5d electronic transition. The emission spectra of all the compositions show green color emission (in the spectral region 450–550 nm with a peak maximum at 502 nm and a shoulder at ~ 490 nm) with appropriate Comission Internationale de l'Eclairage (CIE) color coordinates. The two emission peaks are due to the presence of Eu²⁺ in two different Ba sites in the BaZnSiO₄ host lattice. The energy transfers between the Eu²⁺ ions in BaZnSiO₄ host are elucidated from the critical concentration quenching data based on the electronic multipolar interaction. All Eu²⁺‐activated BaZnSiO₄ phosphor materials can be efficiently excited in the ultraviolet (UV) to near UV‐region (270–420 nm), making them attractive candidate as a green phosphor for solid state lighting–white light‐emitting diodes.     

Study on luminescence properties of Ce3+ and Eu3+ ions in a nanocrystalline hexagonal Zn4Al22O37 novel system

The present communication is strongly focused on the investigation of synthesis, structural and luminescence properties of cerium (Ce³⁺)- and europium (Eu³⁺)-activated Zn₄Al₂₂O₃₇ phosphors. Ce³⁺- and Eu³⁺-doped Zn₄Al₂₂O₃₇ novel phosphors were prepared using a solution combustion synthesis route. Structural properties were studied using powder X-ray diffraction and high-resolution transverse electron microscopy. The optical properties were studied using ultraviolet–visible light spectroscopy and Fourier transform infrared spectroscopy; luminescence properties were studied using a photoluminescence (PL) technique. The crystal structure of the prepared Zn₄Al₂₂O₃₇ host and Ce³⁺- and Eu³⁺-activated Zn₄Al₂₂O₃₇ phosphors was investigated and was found to have a hexagonal structure. The measured PL emission spectrum of the Ce³⁺-doped Zn₄Al₂₂O₃₇ phosphor showed an intense and broad emission band centred at 421 nm under a 298 nm excitation wavelength. By contrast, the Eu³⁺-doped Zn₄Al₂₂O₃₇ phosphor exhibited two strong and intense emission bands at approximately 594 nm (orange) and 614 nm (red), which were monitored under 395 nm excitation. The Commission Internationale de l’Eclairage (CIE) colour coordinates of the Ce³⁺-doped Zn₄Al₂₂O₃₇ were investigated and found to be x = 0.1567, y = 0.0637 (blue) at 421 nm and for Eu³⁺-doped Zn₄Al₂₂O₃₇ were x = 0.6018, y = 0.3976 (orange) at 594 nm and x = 0.6779, y = 0.3219 (red) at 614 nm emission. The luminescence behaviour of the synthesized phosphors suggested that these phosphors may be used in lighting applications.