Use of porous glass fiber as a support for biocatalyst immobilization

Summary Porous glass fiber has a very high surface area and good mechanical properties that make it an excellent support for biocatalyst immobilization. By packing aligned glass fibers in a tubular reactor such that the fibers are all parallel to the axis of the tube, the resulting pressure drop is considerably smaller than for a similar bed of packed beads. The utility of this support was demonstrated by immobilizing -glucoamylase by silane-glutaraldehyde coupling, and measuring its activity toward converting maltose to glucose. Using optimized immobilization conditions, an enzyme loading of 1.5 mg protein perm ² surface area was obtained, with an activity of 370 units/g glass at 50°C. The half-life of the immobilized glucoamylase was more than twice as long as that of the free enzyme.     

Modification of yeast metabolism by immobilization onto porous glass

Summary Porous glass beads are used to immobilizeSaccharomyces carlsbergensis cells. If silica pores are large enough, adsorption occurs. On the other hand, activation of the silica by glutaraldehyde allows the cells to bind onto the support. In the other case, the most porous glass has the greatest retention capacities. In all cases, 15 min is sufficient for support saturation by microorganisms.The study of glucose fermentation in immobilized cells shows that immobilization modifies the metabolism. Adsorption leads to an acceleration of metabolism, while a slowing down of the cell's activity follows covalent binding. Nevertheless, in both cases yield of glucose converted into ethanol increases while yield of glucose converted into carbon dioxide decreases.     

Effective diffusivity and tortuosity in a porous glass immobilization matrix

The effective diffusivity of glucose in porous glass beads was determined using a transient method. Predictions for the intraparticle and surface concentrations were made by an analytical solution of the mass balance. The value of the diffusivity was expected to be lower than the value of the corresponding diffusion coefficient in water, but the opposite was observed. This effect results from intraparticle fluid flow, leading to high values of the apparent effective glucose diffusivity. To measure diffusion only and to prevent any internal convection during the diffusion experiment, the pores of the porous glass beads were filled with Ca-alginate gel. For these glass beads (internal porosity, , equal to 0.56), we found an effective glucose diffusivity of 2.2×10^–10 m²/s at 30°C. Using the relationship to effective intraparticle diffusivity (D_eff)=effective diffusivity in 1% Ca-alginate beads (D_gel) / (with the tortuosity factor) this gives =1.7. For known and measuring by the method described, the D_eff can be calculated for other porous materials or diffusing substances. Knowledge of the exact value of the effective diffusivity is a necessity in bioreactor modelling and was demonstrated by prediction of the residence time distribution profiles in a packed-bed bioreactor containing immobilized yeast cells.     

The use of a water-soluble carbodiimide to cross-link cytochrome c to plastocyanin

Canine cardiac sarcoplasmic reticulum is phosphorylated by adenosine 3',5'-monophosphate (cAMP)-dependent and by Ca2+-calmodulin-dependent protein kinases on an Mr 22 000 protein called phospholamban. Both types of phosphorylation are associated with an increase in the initial rate of Ca2+ transport. Thus, phospholamban appears to be a regulator for the calcium pump in cardiac sarcoplasmic reticulum. However, there is conflicting evidence as to the degree of association of the Ca2+-ATPase with its regulator, phospholamban. In this study, we report that phospholamban does not copurify with a Ca2+-ATPase preparation of high specific activity. Although 32P-labeled phospholamban is solubilized in the same fraction as the Ca2+-ATPase from cardiac sarcoplasmic reticulum, it dissociates from the Ca2+ pump during subsequent purification steps. Our isolation procedure results in an increase of over 4-fold in the specific activity of the Ca2+-ATPase, but a decrease of 2.5-fold in the specific activity of 32Pi-phosphoester bonds (pmol Pi/mg). Furthermore, the purified Ca2+-ATPase enzyme preparation is not a substrate for protein kinase in vitro to any significant extent. These data indicate that phospholamban does not copurify with the Ca2+-ATPase from cardiac sarcoplasmic reticulum. Isolation of a Ca2+-ATPase preparation essentially free of phospholamban will aid in future kinetic studies designed to elucidate similarities and differences in the Ca2+-ATPase parameters from cardiac and skeletal muscle (which is known not to contain phospholamban).     

Determination of intrinsic parameters for immobilization reactions of catalase and amyloglucosidase in porous glass supports

Experiments have been carried out for immobilizing enzyme-catalase and amyloglucosidase in controlled-pore glass particles of two different pore sizes. The experimental results have been analyzed, initial-stage analysis for the rate parameters of immobilization reactions and long-time analysis for determining the evolution of the immobilization process. These investigations suggest that the overall process of immobilization is controlled by the restricted diffusion of enzymes into the pores of the support. As a result, immobilized enzyme (IME) can penetrate only up to a certain distance into the support. The penetration depth of IME for the support-enzyme system mentioned have been evaluated from the experimental bulk enzyme concentration data in a batch recirculation reactor.     

High-throughput optimization of surfaces for antibody immobilization using metal complexes

Using a high-throughput surface discovery approach, we have generated a 1600-member library of metal-containing surfaces and screened them for antibody binding potential. The surface library assembly involved graft modification of argon plasma-treated polyvinylidenedifluoride (PVDF) membranes with alternating maleic anhydride-styrene copolymer followed by anhydride ring opening with a range of secondary amines and microarray contact printing of transition metal complexes. The microarrays of metal-containing surfaces were then tested for their antibody binding capacity by incubation with a biotinylated mouse antibody in a chemiluminescence assay. A total of 11 leads were identified from the first screen, constituting a "hit" rate of 0.7%. A smaller 135-member surface library was then synthesized and screened to optimize existing hits and generate additional leads. To demonstrate the applicability of these surfaces to other formats, high-binding surface leads were then transferred onto Luminex beads for use in a bead flow cytometric immunoassay. The novel one-step antibody coupling process increased assay sensitivity of a Luminex tumor necrosis factor immunoassay. These high-binding surfaces do not require prior incorporation of polyhistidine tags or posttreatments such as oxidation to achieve essentially irreversible binding of immunoglobulin G.     

The use of a water-soluble carbodiimide to cross-link cytochrome c to plastocyanin

A water-soluble carbodiimide, 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide, has been used to cross-link horse heart cytochrome c to spinach chloroplast plastocyanin. The complex was formed in yields up to 90%, and was found to have a stoichiometry of 1 mol plastocyanin per mol cytochrome c. The cytochrome c in the complex was fully reducible by ascorbate and potassium ferrocyanide, and had a redox potential only 25 mV less than that of native cytochrome c. The complex was nearly completely inactive towards succinate-cytochrome c reductase and cytochrome c oxidase, suggesting that the heme crevice region of cytochrome c was blocked. We propose that the carbodiimide promoted the formation of amide cross-links between lysine amino groups surrounding the heme crevice of cytochrome c and complementary carboxyl groups on plastocyanin. It is of interest that the high-affinity site for cytochrome c binding on bovine heart cytochrome c oxidase has recently been found to involve a sequence of subunit II with some homology to the copper-binding sequence of plastocyanin.     

In vitro selection of optimal DNA substrates for ligation by a water-soluble carbodiimide

We have used in vitro selection to investigate the sequence requirements for efficient template-directed ligation of oligonucleotides at 0°C using a water-soluble carbodiimide as condensing agent. We find that only 2 by at each side of the ligation junction are needed. We also studied chemical ligation of substrate ensembles that we have previously selected as optimal for ligation by RNA ligase or by DNA ligase. As anticipated, we find that substrates selected with DNA ligase ligate efficiently with a chemical ligating agent, and vice versa. Substrates selected using RNA ligase are not ligated by the chemical condensing agent and vice versa. The implications of these results for prebiotic chemistry are discussed.Correspondence to: Leslie E. Orgel 1444     

Affinity chromatography of proteinases using bacitracin immobilized to porous glass beads

J. FONTECHA, T. REQUENA AND H.E. SWAISGOOD. 1996. This study describes an affinity chromatography procedure for proteinase purification using bioselective binding to immobilized bacitracin. By coupling bacitracin to controlled-pore glass (CPG) beads, an affinity matrix was obtained that permitted rapid purification of proteinases under conditions that minimize autolysis. Bacitracin-CPG was used to bioselectively adsorb the extracellular proteinase secreted by Enterococcus faecalis var. liquefaciens IFPL 383. The overall purification obtained with this procedure was 5149-fold. The ability of bacitracin-CPG to bind other proteinases was examined using various commercial proteinases. The specific activities of subtilin BPN' and proteinase K were increased by bioselective adsorption and excellent recoveries of all proteinases applied were obtained.     

Comparison of antibody functionality using different immobilization methods

This study investigates the influence of antibody immobilization methods on antigen capture. Adsorption and two surface chemistries, an aminosilane chemistry and a common heterobifunctional crosslinker (N-gamma-maleimidobutyryloxy-succinimide ester, GMBS), were compared and evaluated for their ability to immobilize antibodies and capture antigen. The role of protein A as an orienting protein scaffold component in each of these techniques was also evaluated. Through experimentation it was determined that the GMBS technique immobilized the highest amount of antibody and minimized nonspecific binding. For all techniques, the most functional antibodies were found to be those immobilized with protein A. Interestingly, the aminosilane technique demonstrated the highest antigen capture with antibody alone but also exhibited the highest level of nonspecific binding.     

The sites on calmodulin cross-linked to myosin light chain kinase and troponin I with water-soluble carbodiimide

To elucidate the interaction of calmodulin with calmodulin binding proteins, we studied the location of the interaction sites on calmodulin by using a chemical cross-linking reagent. Calmodulin prepared from wheat germ was cross-linked to myosin light chain kinase and troponin-I with 1-ethyl-3-[3-(dimethylamino)propyl]carbodiimide. The cross-linked products were cleaved partially with cyanogen bromide and cross-linked sites were determined by peptide mapping analysis using SDS-urea polyacrylamide gel electrophoresis. Peptides which contain the cross-linked site were displaced from their position because of the attached fragments of myosin light chain kinase or troponin I. The peptide of calmodulin from the N-terminal to Met-73 in the cross-linked product with myosin light chain kinase had the same mobility as that of uncross-linked calmodulin on the map though the amount of the peptide was decreased in the cross-linked product. The peptide from the N-terminal to Met-110 in the cross-linked product was displaced from its position. Similar change in the mobility of the calmodulin peptides was also observed in the cross-linked products with troponin I. It was concluded, therefore, that at least one cross-linked site for myosin light chain kinase and one for troponin I were located between Met-73 and Met-110 of the wheat germ calmodulin.     

Modification of cardiac sodium channels by carboxyl reagents. Trimethyloxonium and water-soluble carbodiimide

In TTX-sensitive nerve and skeletal muscle Na+ channels, selective modification of external carboxyl groups with trimethyloxonium (TMO) or water-soluble carbodiimide (WSC) prevents voltage-dependent Ca2+ block, reduces unitary conductance, and decreases guanidinium toxin affinity. In the case of TMO, it has been suggested that all three effects result from modification of a single carboxyl group, which causes a positive shift in the channel's surface potential. We studied the effect of these reagents on Ca2+ block of adult rabbit ventricular Na+ channels in cell-attached patches. In unmodified channels, unitary conductance (gamma Na) was 18.6 +/- 0.9 pS with 280 mM Na+ and 2 mM Ca2+ in the pipette and was reduced to 5.2 +/- 0.8 pS by 10 mM Ca2+. In contrast to TTX-sensitive Na+ channels, Ca2+ block of cardiac Na+ channels was not prevented by TMO; after TMO pretreatment, gamma Na was 6.1 +/- 1.0 pS in 10 mM Ca2+. Nevertheless, TMO altered cardiac Na+ channel properties. In 2 mM Ca2+, TMO-treated patches exhibited up to three discrete gamma Na levels: 15.3 +/- 1.7, 11.3 +/- 1.5, and 9.8 +/- 1.8 pS. Patch-to-patch variation in which levels were present and the absence of transitions between levels suggests that at least two sites were modified by TMO. An abbreviation of mean open time (MOT) accompanied each decrease in gamma Na. The effects on channel gating of elevating external Ca2+ differed from those of TMO pretreatment. Increasing pipette Ca2+ from 2 to 10 mM prolonged the MOT at potentials positive to approximately -35 mV by decreasing the open to inactivated (O-->I) transition rate constant. On the other hand, even in 10 mM Ca2+ TMO accelerated the O-->I transition rate constant without a change in its voltage dependence. Ensemble averages after TMO showed a shortening of the time to peak current and an acceleration of the rate of current decay. Channel modification with WSC resulted in analogous effects to those of TMO in failing to show relief from block by 10 mM Ca2+. Further, WSC caused a decrease in gamma Na and an abbreviation of MOT at all potentials tested. We conclude that a change in surface potential caused by a single carboxyl modification is inadequate to explain the effects of TMO and WSC in heart. Failure of TMO and WSC to prevent Ca2+ block of the cardiac Na+ channel is a new distinction among isoforms in the Na+ channel multigene family.     

Characterization and optimization of two methods in the immobilization of 12 bioluminescent strains

Twelve recombinant bioluminescent bacteria have been immobilized within the wells of a 96-well plate using two different matrices--agar and sol-gel. All 12 strains were immobilized within individual wells of the plates and the sensitivity of the strains and the stability of the responses were determined for select chemicals. Each strain was exposed to seven well-characterized chemicals over a wide range of concentrations to demonstrate their individual selectivity for specific toxicants. Although the sensitivity of the immobilized cells was generally lower than cultures grown in liquid media, they were comparable. For example, strain DPD1710, which responds to DNA damage was able to detect mitomycin C, a genotoxin, at a minimum concentration of 0.6 ppb. When immobilized, the lower limit of detection was between 1 and 10 ppb. Finally, using compounds that are known to elicit a response from each of the strains, the stability of the bioluminescent responses were measured over an extended period of 4 weeks. Although the activity of several strains decreased over time, the majority of the strains used in both immobilized systems were still responsive.     

Syntheses and applications of water-soluble reactive polymers for purification and immobilization of biomolecules

Reactive polymers have been prepared by copolymeriz-ing N-isopropyl acrylamide (NIPAM) with N-acryloxy-succinimide (NASI) or glycidyl methacrylate (GMA). The amino groups of ligands could react with the residues of NASI or GMA and the polymers could be precipitated by temperature and/or salinity variation, since they contained the NIPAM residues. As a model, p-aminobenza-midine, a trypsin inhibitor, was attached to the polymers to form water-soluble macroligands, capable of selectively binding trypsin from a trypsin-chymotrypsin solution. After precipitation of the macroligand-trypsin complex, followed by dissociation, approximately 82% trypsin was isolated. The NIPAM-GMA copolymer was also reacted with immunogammaglobulin (IgG) and alkaline phosphatase (AP). It was demonstrated that the IgG bearing polymer was able to bind protein A and the whole complex was precipitable. The reactive polymer was also used for direct immobilization of AP which was active in repeated reactions.     

The use of a water-soluble carbodiimide to study the interaction between Chromatium vinosum flavocytochrome c-552 and cytochrome c

The interaction between horse heart cytochrome c and Chromatium vinosum flavocytochrome c-552 was studied using the water-soluble reagent 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide (EDC). Treatment of flavocytochrome c-552 with EDC was found to inhibit the sulfide: cytochrome c reductase activity of the enzyme. SDS gel electrophoresis studies revealed that EDC treatment led to modification of carboxyl groups in both the M_r 21000 heme peptide and the M_r 46000 flavin peptide, and also to the formation of a cross-linked heme peptide dimer with an M_r value of 42000. Both the inhibition of sulfide: cytochrome c reductase activity and the formation of the heme peptide dimer were decreased when the EDC modification was carried out in the presence of cytochrome c. In addition, two new cross-linked species with M_r values of 34000 and 59000 were formed. These were identified as cross-linked cytochrome c-heme peptide and cytochrome c-flavin peptide species, respectively. Neither of these species were formed in the presence of a cytochrome c derivative in which all of the lysine amino groups had been dimethylated, demonstrating that EDC had cross-linked lysine amino groups on native cytochrome c to carboxyl groups on the heme and flavin peptides. A complex between cytochrome c and flavocytochrome c-552 was required for cross-linking to occur, since ionic strengths above 100 mM inhibited cross-linking.