Effective biomass harvesting of marine diatom Chaetoceros muelleri by chitosan-induced flocculation,preservation of biomass,and recycling of culture medium for aquaculture feed application

Microalgae are a promising new source of biomass; however, large-scale economical harvesting of microalgal biomass is a major technological and economic challenge, limiting the commercial production of microalgal biomass for high-value compounds. In this study, the cationic polymer chitosan was used for the harvesting of the marine diatom Chaetoceros muelleri. Natural flocculation, and pH and chitosan-induced flocculation were studied in detail. The effects of flocculant dosage, culture pH, initial biomass concentration, and sedimentation time were investigated on biomass recovery. The results showed that flocculation efficiency can reach > 99% with an optimum dosage of chitosan (80 mg L^?1) at pH 9.6 and settling time of 40 minutes for biomass concentration from 0.2 to 1.2 g L^?1. The reusability of the recycled water, preservation of biomass after harvesting, and cost of the harvesting process were evaluated. The results showed that the chitosan-induced flocculation offers an efficient, cost-effective, rapid, and sustainable harvesting method for C. muelleri biomass for food and feed applications in aquaculture.

     

Effect of pH,Temperature, and Lead Concentration on the Bioremoval of Lead from Water Using Lemna Minor

This study examined the ability of the aquatic plant Lemna minor (duckweed) to remove soluble lead under various laboratory conditions. In a batch process L. minor was exposed to different pH values (4.5–8.0) and temperature (15–35°C) in presence of different lead concentrations (0.1–10.0 mg L^?1) for 168 h. The amount of biomass obtained in the study period on a dry weight basis, the concentrations of lead in tissue and in medium and net uptake of lead by Lemna all have been determined in each condition. The percentages of lead uptake ratios (PMU) and bioconcentration factors (BCF) were also calculated for these conditions. Bioaccumulated lead concentrations and the PMU were obtained at lowest pH of 4.5, and at 30°C. The highest accumulated lead concentration was found at pH 4.5 as 3.599 mg Pb g^?1 in 10.0 mg L^?1. It decreased to pH 6.0, but it did not change at pH 6.0–8.0 range. The maximum lead accumulation was obtained at 30°C as 8.622 mg Pb g^?1 in 10 mg L^?1 at pH 5.0, and the minimum was at 15°C as 0.291 mg g^?1 in 0.1 mg L^?1. Lead accumulation gradually increased with increasing lead in medium, but the opposite trend was observed for PMU. Lead accumulation increased up to 50 mg L^?1, but did not change significantly in the 50.0–100.0 mg L^?1 range. The lead uptake from water was modeled and the equation fit the experimental data very well.     

Optimization of Chlorella biomass harvesting by flocculation and its potential for biofuel production

Optimization of microalgal biomass harvesting is essential to produce effective and optimum outcomes that can contribute towards a feasible and economical harvesting technique. Two Chlorella species were used, namely, C. vulgaris and C. sorokiniana UKM3. Two essential factors affecting microalgal biomass harvesting via flocculation, namely, the initial pH of the microalgal broth and flocculant (chitosan) concentration were studied. The optimization process was conducted by using a response surface methodology (RSM) based on the model of face-centered-central composite design (FC-CCD). The potential for biofuel application of the harvested biomass was evaluated based on the production of fatty acid methyl esters (FAMEs) by transesterification. The quadratic models obtained from the RSM significantly fitted the experiment data as the p-values were less than 0.05. The initial pH of the microalgal suspension was found to have a more significant effect on the flocculation process than flocculant concentration. For C. vulgaris, the highest flocculant efficiency of 98.7% was obtained at a chitosan concentration of 0.2 g L^?1 and an initial pH of 12.0, whereas for C. sorokiniana UKM3, at 0.15 g L^?1 of chitosan and initial pH of 12.0 produced the highest efficiency of 97.1%. The harvested biomass of both species exhibited a high content of palmitic acid (C16:0) with 29.74 wt% and 11.81 wt% of dry biomass for C. vulgaris and C. sorokiniana UKM3, respectively. This study showed that Chlorella species can be harvested efficiently using the flocculation process and manifested an excellent potential for biodiesel production where palmitic acid (C16:0) is one of the main compounds for high-acid oil-biodiesel.

     

Effects of different nitrogen, phosphorus, and iron concentrations and salinity on lipid production in newly isolated strain of the tropical green microalga, Scenedesmus dimorphus KMITL

The fatty acid composition, the effect of different concentrations of nitrogen (16.5-344 mg ?L^?1), phosphorus (9–45 mg? L^?1), iron (9–45 mg? L^?1) and salinity levels (0–20 psu) on lipid production in the green microalga Scenedesmus dimorphus KMITL, a new strain isolated from a tropical country, Thailand, were studied. The alga was isolated from a freshwater fish pond, and cultured in Chlorella medium by varying one parameter at a time. The main fatty acid composition of this strain was C16–C18 (97.52 %) fatty acids. A high lipid content was observed in conditions of 16.5 mg? L^?1-N, or 22 mg ?L^?1-P, or 45 mg ?L^?1-Fe, or 5 psu salinity, which accumulated lipids to 20.3?±?0.4, 19.4?±?0.2, 24.7?±?0.5, and 14.3?±?0.2 % of algal biomass, respectively. Increasing lipid content and lipid productivity was noted when the alga was cultured under high iron concentration and high salinity, as well as under reduced phosphorus conditions, whereas nitrogen limitation only resulted in an increased lipid content.     

Optimization of culture conditions and bench-scale production of anticancer enzyme L-asparaginase by submerged fermentation from Aspergillus terreus CCT 7693

L-Asparaginase amidohydrolase (EC 3.5.1.1) has received significant attention owing to its clinical use in acute lymphoblastic leukemia treatment and non-clinical applications in the food industry to reduce acrylamide (toxic compound) formation during the frying of starchy foods. In this study, a sequential optimization strategy was used to determine the best culture conditions for L-asparaginase production from filamentous fungus Aspergillus terreus CCT 7693 by submerged fermentation. The cultural conditions were studied using a 3-level, central composite design of response surface methodology, and biomass and enzyme production were optimized separately. The highest amount of biomass (22.0?g·L^?1) was obtained with modified Czapek–Dox medium containing glucose (14?g·L^?1), L-proline (10?g·L^?1), and ammonium nitrate (2?g·L^?1) fermented at 37.2?°C and pH 8.56; for maximum enzyme production (13.50?U·g^?1), the best condition was modified Czapek–Dox medium containing glucose (2?g·L^?1), L-proline (10?g·L^?1), and inoculum concentration of 4.8?×?10⁸ espore·mL^?1 adjusted to pH 9.49 at 34.6?°C. The L-asparaginase production profile was studied in a 7?L bench-scale bioreactor and a final specific activity of 13.81?U·g^?1 was achieved, which represents an increase of 200% in relation to the initial non-optimized conditions.     

Sorption characteristics and mechanisms of Pb(II) from aqueous solution by using bioflocculant MBFR10543

This paper focuses on the effectiveness of removing Pb(II) from aqueous solution using bioflocculant MBFR10543 and a series of experimental parameters including MBFR10543 dose, calcium ions concentration, solution pH, and temperature on Pb(II) uptake was evaluated. Meanwhile, the flocculation mechanism of MBFR10543 was discussed. Results have demonstrated that the removal efficiency of Pb(II) reached 94.7 % (with the sorption capacity of 81.2 mg?·?g^?1) by adding MBFR10543 in two stages, separately, 3?×?10^?2 % (w/w) in the 1.0 min’s rapid mixing (180 rpm) and 4?×?10^?2 % (w/w) after 2.0 min’s slow mixing (80 rpm) with pH value fixed at 6. Pb(II) flocculation process could be described by the Langmuir isotherms model and pseudo-second-order kinetic model. The negative Gibbs free energy change indicated the spontaneous nature of the flocculation. Fourier transform infrared spectra analysis indicated that functional groups, such as –OH, C=O, and C–N, were existed in MBFR10543 molecular chains, which had strong capacity for removing Pb(II). Furthermore, both charge neutralization and bridging being the main mechanisms involved in Pb(II) removal by MBFR10543.     

The Effects of Selenium on Physiological Traits, Grain Selenium Content and Yield of Winter Wheat at Different Development Stages

The paper evaluated the effects of Se application time and rate on physiological traits, grain Se content, and yield of winter wheat by field experiment. Se application significantly increased grain Se content and yield, and the increased amount treated with 20 and 30 mg Se?L^?1 was the highest. At blooming–filling stage, Se application significantly increased grain Se content, but did not affect yield. Chlorophyll content was increased by Se application, and the increased amount at heading–blooming stage was higher than that in wheat leaves at the other stages. At four development stages, Se treatments (except for 10 mg Se?L^?1 at jointing–heading stage) significantly decreased the rate of superoxide (O₂ ^?) radical production. At heading–blooming (except for 50 mg Se?L^?1) and blooming–filling stages, hydrogen peroxide (H₂O₂) content was significantly decreased by Se treatments. The rate of O₂ ^? production and H₂O₂ content at 20 and 30 mg Se?L^?1 was the lowest. Se treatments (except for 10 mg Se?L^?1 at regreening–jointing and blooming–filling stages) also induced an evident decrease in malondialdehyde content. Proline content induced by Se treatments at jointing–heading and heading–blooming stages was higher than that in wheat leaves at regreening–jointing and blooming–filling stages. At four development stages, Se treatments all significantly increased glutathione peroxidase activity, and the treatments with 20 and 30 mg Se?L^?1 also evidently increased reduced glutathione content. These results suggested that Se application at different development stages increased antioxidant capacity of wheat, reduced oxidant stress to some extent, and the effects of Se treatments was the best if Se concentration ranged between 20 and 30 mg Se?L^?1. In addition, Se application time was more beneficial for Se accumulation and yield in wheat grain at heading–blooming stage.     

Improved enzymatic two-phase biotransformation for (R)-phenylacetylcarbinol: Effect of dipropylene glycol and modes of pH control

An octanol/aqueous two-phase process for the enzymatic production of (R)-phenylacetylcarbinol (PAC) has been investigated further with regard to optimal pH control and replacement of 2.5?M MOPS buffer by a low cost solute. The specific rate of PAC production in the 2.5?M MOPS system controlled at pH?7 was 0.60?mg?U^?1?h^?1 (reaction completed at 34?h), a 1.6 times improvement over the same 2.5?M MOPS system without pH control (0.39?mg?U^?1?h^?1 at 49?h). An improved stability of PDC was evident at the end of biotransformation for the pH-controlled system with 84% residual carboligase activity, while 23% of enzyme activity remained in the absence of pH control. Lowering the MOPS concentration to 20?mM resulted in a lower benzaldehyde concentration in the aqueous phase with a major increase in the formation of by-product acetoin and three times decreased PAC production (0.21?mg?U^?1?h^?1). Biotransformation with 20?mM MOPS and 2.5?M DPG as inexpensive replacement of high MOPS concentrations provided similar aqueous phase benzaldehyde concentrations compared to 2.5?M MOPS and resulted in a comparable PAC concentration (92.1?g?L^?1 in the total reaction volume in 47?h) with modest formation of acetoin.     

An efficient selection and regeneration protocol for Agrobacterium-mediated transformation of oriental melon (Cucumis melo L. var. makuwa)

An efficient selection and plant regeneration protocol for Agrobacterium-mediated transformation using cotyledon explants of oriental melon (Cucumis melo L. var. makuwa) has been developed. All six oriental melon cultivars evaluated in the study showed a >90?% shoot regeneration frequency and produced 1.8?C3.6 shoots per cotyledon explant when cultured on Murashige and Skoog (MS) medium supplemented with 1.0?mg?L^?1 benzyladenine and 0.01?mg?L^?1 indoleacetic acid. Kanamycin (Km) and geneticin (Gt) in the shoot induction medium (SIM) were compared both qualitatively and quantitatively for their efficiency as a selection agent for the selection and regeneration of transgenic plants after Agrobacterium-mediated transformation. Shoot formation was completely inhibited at 50?mg?L^?1 Km and 10?mg?L^?1 Gt. Relatively high concentrations of both Gt and Km (>100?mg?L^?1 Km and >25?mg?L^?1 Gt) were necessary because large numbers of non-transgenic shoots survived during the selection process. The incorporation of a selectable marker (neomycin phosphotransferase II) into the genome of transgenic plants was confirmed using ??-glucuronidase (GUS), PCR and Southern blot analysis. Shoot regeneration frequencies were 41.2?% at 100?mg?L^?1 Km and 15.2?% at 30?mg?L^?1 Gt 8?weeks after transformation, whereas the transformation frequencies based on the PCR were 2.9 and 7.1?%, respectively, 16?weeks after transformation. These results demonstrate that a large portion of the regenerated shoots on SIM supplemented with 100?mg?L^?1 Km consisted of non-transformed or escaped shoots, indicating that 30?mg?L^?1 Gt is the more suitable for the selection and regeneration of transgenic plants in oriental melon.     

Evaluation of electrocoagulation,flocculation, and sedimentation harvesting methods on microalgae consortium grown in anaerobically digested abattoir effluent

Microalgae dewatering is a major bottleneck for biomass production in a large-scale microalgal production system which accounts for 20–60% of production cost. In this study, three dewatering systems of electrocoagulation, flocculation, and pH-induced flocculation were evaluated for microalgal consortium grown in anaerobically digested abattoir effluent at pH 6.5 and 9.5. At the shortest time (15 min) and the highest current density (0.08 A cm^?2), the highest microalgae recoveries of 78 and 84% were obtained with the corresponding power consumptions of 1.25 and 1.07 kWh kg^?1 for cultures at pH 6.5 and 9.5. For microalgae suspension at pH 6.5, the highest biomass recovery of 77% was obtained when 100 mg L^?1 of FeCl₃·6H₂O (after 15 min) or 100 mg L^?1 of Al₂(SO₄)₃·18H₂O (after 30 min) was added. However, microalgal recoveries significantly increased when FeCl₃·6H₂O or Al₂(SO₄)₃·18H₂O was used with the culture at pH 9.5. pH-Induced experiments showed that cultures adjusted at pH 10.5 had 36% higher biomass recovery compared to that in cultures at pH 8.5 after 2 h. The results of this study showed that cultures at higher pH (9.5) had a better microalgae recovery in all dewatering systems than cultures at lower pH (6.5).

     

Simultaneous Removal of Mn(II) and Nitrate by the Manganese-Oxidizing Bacterium Acinetobacter sp. SZ28 in Anaerobic Conditions

A novel bacterium, strain SZ28, identified as Acinetobacter sp., showed anaerobic denitrification ability using Mn(II) as the electron donor. Nitrate-nitrogen concentration decreased from nearly 16.52–mg L^?1 to 4.4–mg L^?1, without accumulation of nitrite as an intermediate, with a maximum of 0.063–mg NO₃^?-N L^?1 h^?1, reaching a peak of 0.085–mg NO₃^?-N L^?1 h^?1 in sodium acetate. The nitrate removal rate reached 0.067–mg NO₃^?-N L^?1 h^?1, 0.059–mg NO₃^?-N L^?1 h^?1, and 0.078 mg NO₃^?-N L^?1 h^?1 using Mn(II), S(II), and Fe(II) as electron donors, respectively. The optimum pH was 6.0, with a removal rate of 0.063–mg NO₃^?-N L^?1 h^?1     

Improved accumulation of betulin and betulinic acid in cell suspension culture of Betula pendula roth by abiotic and biotic elicitors

Abstract

Betulin (B) and betulinic acid (BA) are two triterpenes with diverse pharmacological and physiological actions. Elicitation of Betula pendula Roth cell cultures by elicitors is an excellent strategy to increase B and BA levels. Six abiotic and biotic elicitors were studied to improve accumulation of B and BA in the cell culture of B. pendula. The B and BA production in treated cells was verified by HPLC. The results showed the maximum growth index (7) on day 3 in cells treated with 0.5?mg L^?1 chlorocholine chloride (CCC). The increased accumulation of BA in the cells treated with 200?mg L^?1 of chitosan was found to be 5.9?×?(6.5?mg g^?1 DW) higher over control cells. Treating the cells with 2?mg L^?1 of CCC, after 7?days, led to 149.3× enhancement of B content (19.4?mg g^?1 DW) over the controls. Production of this triterpenoid at a much shorter time with a much higher growth rate can be economic and lead to producing large amounts of B and BA for anti-cancer and HIV drugs preparation.     

Inorganic carbon and pH effect on growth and lipid productivity of Tetraselmis suecica and Chlorella sp (Chlorophyta) grown outdoors in bag photobioreactors

There has been considerable interest in cultivation of green microalgae (Chlorophyta) as a source of lipid that can alternatively be converted to biodiesel. However, almost all mass cultures of algae are carbon-limited. Therefore, to reach a high biomass and oil productivities, the ideal selected microalgae will most likely need a source of inorganic carbon. Here, growth and lipid productivities of Tetraselmis suecica CS-187 and Chlorella sp were tested under various ranges of pH and different sources of inorganic carbon (untreated flue gas from coal-fired power plant, pure industrial CO₂, pH-adjusted using HCl and sodium bicarbonate). Biomass and lipid productivities were highest at pH 7.5 (320?±?29.9 mg biomass L^?1 day^?1and 92?±?13.1 mg lipid L^?1 day^?1) and pH 7 (407?±?5.5 mg biomass L^?1 day^?1 and 99?±?17.2 mg lipid L^?1 day^?1) for T. suecica CS-187 and Chlorella sp, respectively. In general, biomass and lipid productivities were pH 7.5?>?pH 7?>?pH 8?>?pH 6.5 and pH 7?>?pH 7.5?=?pH 8?>?pH 6.5?>?pH 6?>?pH 5.5 for T. suecica CS-187 and Chlorella sp, respectively. The effect of various inorganic carbon on growth and productivities of T. suecica (regulated at pH?=?7.5) and Chlorella sp (regulated at pH?=?7) grown in bag photobioreactors was also examined outdoor at the International Power Hazelwood, Gippsland, Victoria, Australia. The highest biomass and lipid productivities of T. suecica (51.45?±?2.67 mg biomass L^?1 day^?1 and 14.8?±?2.46 mg lipid L^?1 day^?1) and Chlorella sp (60.00?±?2.4 mg biomass L^?1 day^?1 and 13.70?±?1.35 mg lipid L^?1 day^?1) were achieved when grown using CO₂ as inorganic carbon source. No significant differences were found between CO₂ and flue gas biomass and lipid productivities. While grown using CO₂ and flue gas, biomass productivities were 10, 13 and 18 %, and 7, 14 and 19 % higher than NaHCO₃, HCl and unregulated pH for T. suecica and Chlorella sp, respectively. Addition of inorganic carbon increased specific growth rate and lipid content but reduced biomass yield and cell weight of T. suecica. Addition of inorganic carbon increased yield but did not change specific growth rate, cell weight or content of the cell weight of Chlorella sp. Both strains showed significantly higher maximum quantum yield (F_v/F_m) when grown under optimum pH.     

Optimization of growth conditions and fatty acid analysis for three freshwater diatom isolates

Diatoms are a group of highly abundant and diverse aquatic algae species. They contain high lipid content along with many bioactive compounds that can be exploited for biotechnological applications. Despite these attractive attributes, diatoms are underrepresented in production projects due to difficulties in their cultivation. To optimize the growth of three freshwater diatom isolates, Cyclotella sp., Synedra sp. and Navicula sp., an orthogonal assay on N, P, Si and Fe, as well as temperature and pH, was designed using traditional single‐factor tests. We also studied the effect of using nanosilica as an alternate Si source on growth and found that the diatom isolates studied achieved their highest growth rates under different combinations of nutrient and environmental conditions. Silica had the greatest influence on growth, followed by phosphate and iron. The optimized growth conditions for Synedra sp. were N: 30 mg L^?1, P: 3 mg L^?1, Si: 14.8 mg L^?1, Fe: 0.448 mg L^?1, temperature 25°C and pH 8. For Navicula sp.: N: 20 mg L^?1, P: 2.5 mg L^?1, Si: 19.7 mg L^?1, Fe: 0.112 mg L^?1, temperature 30°C and pH 7.5–8. For Cyclotella sp.: N: 20 mg L^?1, P: 2.5 mg L^?1, Si: 19.7 mg L^?1, Fe: 0.448 mg L^?1, temperature 30°C and pH 7.5–8. Nano silica negatively affected growth in Navicula sp. and Cyclotella sp., but no such effect was observed in Synedra sp. Fatty acid profiling showed C16:0, C16:1(n ? 7), C18:0 and C20:5(n ? 3) as major fatty acids, with no significant differences in fatty acid methyl ester profiles between traditional and modified media. This work gives us a new insight into the growth requirements of freshwater diatom species, which are less studied than marine species.     

pH dependent salinity-boron interactions impact yield, biomass, evapotranspiration and boron uptake in broccoli (Brassica oleracea L.)

Aims

Soil pH is known to influence many important biochemical processes in plants and soils, however its role in salinity—boron interactions affecting plant growth and ion relations has not been examined. The purpose of this research was to evaluate the interactive effects of salinity, boron and soil solution pH on broccoli (Brassica oleracea L.) growth, yield, consumptive water use and shoot-boron accumulation.

Methods

A greenhouse experiment was conducted using a sand tank system where salinity-B-pH treatment solutions were supplemented with a complete nutrient solution. Sulfate-dominated irrigation waters, characteristic of groundwater in California’s San Joaquin valley (SJV), were tested at EC levels of 2, 5, 8, 11 and 14 dS?m^?1. Each salinity treatment consisted of two boron treatments (0.5 and 21 mg?L^?1) and each of those treatments was tested under slightly basic (pH?8.0) and slightly acidic (pH?6.0) conditions.

Results

Results included multiple salinity-boron-pH interactions affecting shoot biomass, head yield and consumptive water use. Broccoli fresh head yields were significantly reduced by salinity and boron, but the degree of yield reductions was influenced by pH. Relative head yields were substantially reduced in treatments with high pH and high B, particularly under low and high salinity where head yields were decreased by 89 % and 96 %, respectively, relative to those at low salinity and low boron. Intermediate levels of salinity were far less damaging. Increased salinity and boron reduced evapotranspiration (ET) and there were no salinity-boron associated interactions on ET. However, increased salinity and boron concentrations increased water use efficiency (shoot biomass/cumulative volume ET). Shoot B concentration increased with increased boron and was greater at pH?6 as compared to pH?8. Shoot boron concentration decreased with increasing salinity at both pH levels but particularly at the high substrate boron concentration.

Conclusions

It is likely that different mechanisms, yet unknown, are responsible for severe head-yield reductions at low and high salinity in the presence of high boron under alkaline conditions. We found that boron in the shoot did not accumulate by a simple passive process. Rather as boron increased from 0.5 to 21 mg?L^?1, there was a restrictive mechanism where total shoot boron (mg plant^?1) was reduced by 10 to 40 times the amount potentially supplied to the shoot by passive transport via mass flow perhaps involving complex interactions with membrane channels and B exporters. Total shoot boron concentration was a poor indicator of plant growth response.     

Identification of somaclonal variants in proliferating shoot cultures of Senecio cruentus cv. Tokyo Daruma

A protocol for in vitro propagation of cineraria (Senecio cruentus) was developed. The highest frequency of shoot proliferation was obtained from nodal explants cultured on Murashige and Skoog (MS) medium supplemented with 2.0?mg L^?1 6-benzyladenine (BA) and 0.5?mg L^?1 ??-naphthalene acetic acid (NAA), with a mean number of 14 shoots per explant. A high concentration of BA (4.0?mg L^?1) and repeated subcultures resulted in hyperhydric shoots. Decreasing the BA concentration to 1.0?mg L^?1 in the culture medium eliminated hyperhydricity. The concentration of ammonium nitrate (NH₄NO₃) and temperature had marked effects on somaclonal variation. Variation was observed when the cultures were maintained at 15?°C but not at 25?°C. Variants with blue-colored leaves and stems were identified; whereas, normal plants maintained their green-colored leaves and stems. The highest frequency of variation (67.5?%), with a mean number of 3.0 variant shoots per explants, was obtained on shoot proliferation medium (MS?+?2.0?mg L^?1 BA and 0.5?mg L^?1 NAA) devoid of NH₄NO₃. The best rooting (100?%), with the highest number of roots per shoot (10.8) and the greatest root length (6.8?cm) was obtained on medium supplemented with 0.1?mg L^?1 NAA. In vitro-grown plantlets were successfully acclimatized in a greenhouse, and transferred to the field.     

Stopped‐flow chemiluminescence determination of the anticancer drug capecitabine: Application in pharmaceutical analysis and drug‐delivery systems

Capecitabine is a chemotherapeutic agent used for the treatment of patients with metastatic cancers. This study aimed at determining the drug capecitabine in a simple chemiluminescence (CL) system of acidic potassium permanganate using the stopped‐flow injection technique. Statistical methods were used to detect optimum conditions. The method showed two linear calibration ranges from 6.7 × 10^?6 to 6.7 × 10^?5 mol L^?1 and from 6.7 × 10^?5 to 2.7 × 10^?3 mol L^?1 with a detection limit of 1.5 × 10^?6 mol L^?1. Chitosan‐modified magnetic nanoparticles were studied in the drug‐delivery experiments. According to the pH sensitivity of chitosan and low pH values in tumour cells, the chitosan‐coated magnetic nanoparticles could provide a good targeting drug‐delivery system to tumour sites. To evaluate the applicability of the method, the capecitabine‐loaded magnetic chitosan nanoparticles were synthesized with two different cross‐linkers; loading and releasing rates of the drug were investigated using the proposed CL method and an ultraviolet–visible light spectrophotometric method (absorption at 305 nm). The results showed a good correlation between the two methods, and it was found that the synthesized chitosan‐modified magnetic nanoparticles could be used for pH‐dependent release of capecitabine in cancer cells. Moreover, determination of capecitabine in tablets and synthetic samples was performed.     

Cumulative Title Index

Abstract

Quantitative data on the speciation of chitosan (310 kDa) with low and high molecular weight carboxylates in aqueous solution are reported. The following carboxylic ligands were considered: monocarboxylate (butyrate); dicarboxylates (malonate, succinate, azelate); tricarboxylate (1,2,3-propa-netricarboxylate); tetracarboxylate (1,2,3,4-butanetetracarboxylate); polyacrylates (2.0 and 20 kDa); polymethacrylate (5.4 kDa). The investigation was performed by potentiometry at t =25°C, at low ionic strength (without addition of supporting electrolyte) and at I =0.15mol L^?1 (NaCl). For all the systems the formation of (chitosan)LH_i species was found (L = carboxylic ligand; i = 1 to 4 depending on the carboxylic ligand considered). The stability of proton–chitosan–carboxylate species depends on the number of carboxylic groups involved in the complexation, and it was possible to calculate a rough free energy value per bond ΔG_n = ?15±2kJ mol^?1. By using the stability data, the quantitative sequestering capacity of chitosan towards the carboxylates here considered [expressed as the-log(total chitosan concentration) necessary to bind 50% of carboxylate, i.e., pL₅₀] was calculated for different pH values, at low ionic strength and at I =0.15 mol L^?1. The pL₅₀ values, ranging from 3 to 7, show that chitosan is quite a strong sequestering agent towards carboxylates. Evidences were also obtained for the different behaviour between low and high molecular weight carboxylates.     

Efficacy of soaking cotton seeds within salicylic acid and potassium silicate on reducing reniform nematode infection

ABSTARCT

The efficiency of soaking cotton cv. Giza 45 seeds in five concentrations of salicylic acid and potassium silicate (5, 10, 15, 20 and 25?mg?L^?1 against Rotylenchulus reniformis infection showed a significant (P?<?0.05) improvement in the tested plant parameters that was distinct in soaked seeds in salicylic acid for 24?hours compared with potassium silicate in greenhouse (28?±?5?°C). The application of concentration (20?mg?L^?1) stated the highest values of improvement of plant criteria, while high concentration (25?mg?L^?1) revealed the maximum reduction rates in the total nematode population for both potassium silicate and salicylic acid. Moreover, seed soaking in salicylic acid and potassium silicate achieved a considerable increment in nitrogen, phosphorus, potassium, phenol and chlorophyll contents in cotton leaves with changeable values.     

Harmful algal blooms mitigation using clay/soil/sand modified with xanthan and calcium hydroxide

A method was studied for marine harmful algal blooms (HABs) mitigation using clay, soil, or sand modified with xanthan and calcium hydroxide. Results showed that xanthan could trap and wrap Amphidinium carterae cells via bridging and netting interactions due to its superior salt compatibility in seawater. The maximum cell removal efficiency was 55% when xanthan was used alone. The removal effect of xanthan was enhanced by the addition of appropriate calcium hydroxide that decreased the repulsive interaction between anionic xanthan and negatively charged algal cells. Three kinds of minerals (clays, soils, and sands) were ineffective in removing algal cells before treatment. When xanthan and calcium hydroxide were used together as modifiers, the removal efficiency increased to 83–89% within 30?min using 300?mg?L^?1 clays, soils, or sands modified with 20?mg?L^?1 xanthan and 100?mg?L^?1 calcium hydroxide. After several hours, 95–98% cell removal was achieved and there was no significant difference in the removal efficiencies among clays, soils, and sands after being modified with xanthan and calcium hydroxide. Thus, the method would provide an alternative modification approach to suppress and mitigate HABs using local soils/sands and polymers in marine systems.