In vivo kinematics and articular surface congruency of total ankle arthroplasty during gait

Relatively high rates of loosening and implant failure have been reported after total ankle arthroplasty. Abnormal kinematics and incongruency of the articular surface may cause increased contact pressure and rotational torque applied to the implant, leading to loosening and implant failure. We measured in vivo kinematics of two-component total ankle arthroplasty (TNK ankle), and assessed congruency of the articular surface during the stance phase of gait. Eighteen ankles of 15 patients with a mean age of 75±6 years (mean±standard deviation) and follow-up of 44±38 months were enrolled. Lateral fluoroscopic images were taken during the stance phase of gait. 3D-2D model-image registration was performed using the fluoroscopic image and the implant models, and three-dimensional kinematics of the implant and incongruency of the articular surface were determined. The mean ranges of motion were 11.1±4.6°, 0.8±0.4°, and 2.6±1.5° for dorsi-/plantarflexion, inversion/eversion, and internal/external rotation, respectively. At least one type of incongruency of the articular surface occurred in eight of 18 ankles, including anterior hinging in one ankle, medial or lateral lift off in four ankles, and excessive axial rotation in five ankles. Among the four ankles in which lift off occurred during gait, only one ankle showed lift off in the static weightbearing radiograph. Our observations will provide useful data against which kinematics of other implant designs, such as three-component total ankle arthroplasty, can be compared. Our results also showed that evaluation of lift off in the standard weightbearing radiograph may not predict its occurrence during gait.     

A mechanical supination sprain simulator for studying ankle supination sprain kinematics

This study presents a free-fall mechanical supination sprain simulator for evaluating the ankle joint kinematics during a simulated ankle supination sprain injury. The device allows the foot to be in an anatomical position before the sudden motion, and also allows different degrees of supination, or a combination of inversion and plantarflexion. Five subjects performed simulated supination sprain trials in five different supination angles. Ankle motion was captured by a motion analysis system, and the ankle kinematics were reported in plantarflexion/dorsiflexion, inversion/eversion and internal/external rotation planes. Results showed that all sprain motions were not pure single-plane motions but were accompanied by motion in other two planes, therefore, different degrees of supination were achieved. The presented sprain simulator allows a more comprehensive study of the kinematics of ankle sprain when compared with some previous laboratory research designs.     

Mobility of the subtalar joint in the intact ankle complex

A previous study by these authors showed that the calcaneus follows a unique path of unresisted coupled motion relative to the tibia during passive flexion and that most of this motion occurred at the ankle level. Subtalar motion in the intact ankle complex was observed only when perturbations from this path were induced by the application of force to the calcaneus. Relative motion of the bones of the ankle complex was tracked by stereophotogrammetry in seven specimens. Anatomical landmarks, reference frames and joint angles were defined by standard techniques. Sequential moments were applied to the calcaneus about the long axis of the tibia. Measured movements at subtalar level demonstrated plantarflexion coupled to supination and internal rotation (inversion) and dorsiflexion coupled to pronation and external rotation (eversion). These movements were resisted and were fully recovered when the external load was removed. Subtalar motion diminished as the ankle approached maximal dorsi- and plantarflexion. Two clearly distinguished mean axes of rotation were observed for inversion and eversion runs. The axes of inversion and eversion of the subtalar complex changed orientation along a preferred and repeatable path. The subtalar joint complex occupied only a single stable position in the unloaded state and with no range of unresisted motion. It is inferred that mobility was possible only by the stretching and lengthening of the ligaments and the indentation of the articular surfaces, requiring the application of loads. The subtalar joint complex behaves like a flexible structure.     

Kinematics of the ankle joint complex in snowboarding

Because snowboarders are known to injure their ankles more often than Alpine skiers, it has been postulated that stiffer snowboard boots would provide better protection to the ankle than current soft boots do. Snowboarders are also known to injure their front ankle more often than their back ankle, presumably because of the asymmetrical rotations of the ankles due to asymmetrical binding adjustement. To test these hypotheses, we measured the kinematics of the feet and legs of 5 snowboarders wearing soft boots and stiffer step-in boots during snowboarding maneuvers using an electromagnetic motion tracking system. The results were expressed in anatomically relevant rotations of the ankle joint complex, namely dorsi-/plantar flexion, eversion/inversion, and internal/external rotation. The measured ankle rotations show differences in the movement patterns of the front and back legs. Step-in boots were shown to allow less dorsiflexion, eversion, and external rotation than softer boots, possibly explaining why they are associated with a lower rate of fractures of the talus than soft boots.     

The three-dimensional kinematics and flexibility characteristics of the human ankle and subtalar joints--Part I: Kinematics

The in-vitro, three dimensional kinematic characteristics of the human ankle and subtalar joint were investigated in this study. The main goals of this investigation were: 1) To determine the range of motion of the foot-shank complex and the associated range of motion of the ankle and subtalar joints; 2) To determine the kinematic coupling characteristics of the foot-shank complex, and 3) To identify the relationship between movements at the ankle and subtalar joints and the resulting motion produced between the foot and the shank. The tests were conducted on fifteen fresh amputated lower limbs and consisted of incrementally displacing the foot with respect to the shank while the motion of the articulating bones was measured through a three dimensional position data acquisition system. The kinematic analysis was based on the helical axis parameters describing the incremental displacements between any two of the three articulating bones and on a joint coordinate system used to describe the relative position between the bones. From the results of this investigation it was concluded that: 1) The range of motion of the foot-shank complex in any direction (dorsiflexion/plantarflexion, inversion/eversion and internal rotation/external rotation) is larger than that of either the ankle joint or the subtalar joint.; 2) Large kinematic coupling values are present at the foot-shank complex in inversion/eversion and in internal rotation/external rotation. However, only a slight amount of coupling was observed to occur in dorsiflexion/plantarflexion.; 3) Neither the ankle joint nor the subtalar joint are acting as ideal hinge joints with a fixed axis of rotation.; 4) Motion of the foot-shank complex in any direction is the result of rotations at both the ankle and the subtalar joints. However, the contribution of the ankle joint to dorsiflexion/plantarflexion of the foot-shank complex is larger than that of the subtalar joint and the contribution of the subtalar joint to inversion/eversion is larger than that of the ankle joint.; 5) The ankle and the subtalar joints have an approximately equal contribution to internal rotation/external rotation movements of the foot-shank complex.     

A geometric model of the human ankle joint.

A two-dimensional four-bar linkage model of the ankle joint is formulated to describe dorsi/plantarflexion in unloaded conditions as observed in passive tests on ankle complex specimens. The experiments demonstrated that the human ankle joint complex behaves as a single-degree-of-freedom system during passive motion, with a moving axis of rotation. The bulk of the movement occurred at the level of the ankle. Fibres within the calcaneofibular and tibiocalcaneal ligaments remained approximately isometric. The experiments showed that passive kinematics of the ankle complex is governed only by the articular surfaces and the ligaments. It was deduced that the ankle is a single-degree-of-freedom mechanism where mobility is allowed by the sliding of the articular surfaces upon each other and the isometric rotation of two ligaments about their origins and insertions, without tissue deformation. The linkage model is formed by the tibia/fibula and talus/calcaneus bone segments and by the calcaneofibular and tibiocalcaneal ligament segments. The model predicts the path of calcaneus motion, ligament orientations, instantaneous axis of rotation, and conjugate talus surface profile as observed in the experiments. Many features of ankle kinematics such as rolling and multiaxial rotation are elucidated. The geometrical model is a necessary preliminary step to the study of ankle joint stability in response to applied loads and can be used to predict the effects of changes to the original geometry of the intact joint. Careful reconstruction of the original geometry of the ligaments is necessary after injury or during total ankle replacement.     

In-vivo range of motion of the subtalar joint using computed tomography

Understanding in vivo subtalar joint kinematics is important for evaluation of subtalar joint instability, the design of a subtalar prosthesis and for analysing surgical procedures of the ankle and hindfoot. No accurate data are available on the normal range of subtalar joint motion. The purpose of this study was to introduce a method that enables the quantification of the extremes of the range of motion of the subtalar joint in a loaded state using multidetector computed tomography (CT) imaging. In 20 subjects, an external load was applied to a footplate and forced the otherwise unconstrained foot in eight extreme positions. These extreme positions were foot dorsiflexion, plantarflexion, eversion, inversion and four extreme positions in between the before mentioned positions. CT images were acquired in a neutral foot position and each extreme position separately. After bone segmentation and contour matching of the CT data sets, the helical axes were determined for the motion of the calcaneus relative to the talus between four pairs of opposite extreme foot positions. The helical axis was represented in a coordinate system based on the geometric principal axes of the subjects’ talus. The greatest relative motion between the calcaneus and the talus was calculated for foot motion from extreme eversion to extreme inversion (mean rotation about the helical axis of 37.3±5.9°, mean translation of 2.3±1.1 mm). A consistent pattern of range of subtalar joint motion was found for motion of the foot with a considerable eversion and inversion component.     

Effects of Forefoot Shoe on Knee and Ankle Loading during Running in Male Recreational Runners

Objectives: Although overuse running injury risks for the ankle and knee are high, the effect of different shoe designs on Achilles tendon force (ATF) and Patellofemoral joint contact force (PTF) loading rates are unclear. Therefore, the primary objective of this study was to compare the ATF at the ankle and the PTF and Patellofemoral joint stress force (PP) at the knee using different running shoe designs (forefoot shoes vs. normal shoes). Methods: Fourteen healthy recreational male runners were recruited to run over a force plate under two shoe conditions (forefoot shoes vs. normal shoes). Sagittal plane ankle and knee kinematics and ground reaction forces were simultaneously recorded. Ankle joint mechanics (ankle joint angle, velocity, moment and power) and the ATF were calculated. Knee joint mechanics (knee joint angle velocity, moment and power) and the PTF and PP were also calculated. Results: No significant differences were observed in the PTF, ankle plantarflexion angle, ankle dorsiflexion power, peak vertical active force, contact time and PTF between the two shoe conditions. Compared to wearing normal shoes, wearing the forefoot shoes demonstrated that the ankle dorsiflexion angle, knee flexion velocity, ankle dorsiflexion moment extension, knee extension moment, knee extension power, knee flexion power and the peak patellofemoral contact stress were significantly reduced. However, the ankle dorsiflexion velocity, ankle plantarflexion velocity, ankle plantarflexion moment and Achilles tendons force increased significantly. Conclusions: These findings suggest that wearing forefoot shoes significantly decreases the patellofemoral joint stress by reducing the moment of knee extension, however the shoes increased the ankle plantarflexion moment and ATF force. The forefoot shoes effectively reduced the load on the patellofemoral joint during the stance phase of running. However, it is not recommended for new and novice runners and patients with Achilles tendon injuries to wear forefoot shoes.     

The effect of weightbearing and external loading on anterior cruciate ligament strain

A force balance between the ligaments, articular contact, muscles and body weight maintains knee joint stability. Thus, it is important to study anterior cruciate ligament (ACL) biomechanics, in vivo, under weightbearing conditions. Our objective was to compare the ACL strain response under weightbearing and non-weightbearing conditions and in combination with three externally applied loadings: (1) anterior-posterior shear forces, (2) internal-external torques, and (3) varus-valgus moments. A strain transducer was implanted on the ACL of 11 subjects. All joint loadings were performed with the knee at 20 degrees of flexion. A significant increase in ACL strain was observed as the knee made the transition from non-weightbearing to weightbearing. During anterior shear loading, the strain values produced during weightbearing were greater than those of the non-weightbearing knee (shear loads <40N). At higher shear loads, the strain values became equal. During axial torsion, an internal torque of 10Nm strained the ACL when the knee was non-weightbearing while an equivalent external torque did not. Weightbearing significantly increased ACL strain values in comparison to non-weightbearing with the application of external torques and low internal torques (<3Nm). The strains became equal for higher internal torques. For V-V loading, the ACL was not strained in the non-weightbearing knee. However, weightbearing increased the ACL strain values over the range of moments tested. These data have important clinical ramifications in the development of rehabilitation protocols following ACL reconstruction since weightbearing has been previously thought to provide a protective mechanism to the healing graft.     

Influence of kinematic analysis methods on detecting ankle and subtalar joint instability

Patients with subtalar joint instability may be misdiagnosed with ankle instability, which may lead to chronic instability at the subtalar joint. Therefore, it is important to understand the difference in kinematics after ligament sectioning and differentiate the changes in kinematics between ankle and subtalar instability. Three methods may be used to determine the joint kinematics; the Euler angles, the Joint Coordinate System (JCS) and the helical axis (HA). The purpose of this study was to investigate the influence of using either method to detect subtalar and ankle joints instability. 3D kinematics at the ankle and subtalar joint were analyzed on 8 cadaveric specimens while the foot was intact and after sequentially sectioning the anterior talofibular ligament (ATFL), the calcaneofibular ligament (CFL), the cervical ligament and the interosseous talocalcaneal ligament (ITCL). Comparison in kinematics calculated from sensor and anatomical landmarks was conducted as well as the influence of Euler angles and JCS rotation sequence (between ISB recommendation and previous research) on the subtalar joint. All data showed a significant increase in inversion when the ITCL was sectioned. There were differences in the data calculated using sensors coordinate systems vs. anatomic coordinate systems. Anatomic coordinate systems were recommended for these calculations. The Euler angle and JCS gave similar results. Differences in Euler angles and JCS sequence lead to the same conclusion in detecting instability at the ankle and subtalar joint. As expected, the HA detected instability in plantarflexion at the ankle joint and in inversion at the subtalar joint.     

A closed-loop cadaveric foot and ankle loading model

Investigations of human foot and ankle biomechanics rely chiefly on cadaver experiments. The application of proper force magnitudes to the cadaver foot and ankle is essential to obtain valid biomechanical data. Data for external ground reaction forces are readily available from human motion analysis. However, determining appropriate forces for extrinsic foot and ankle muscles is more problematic. A common approach is the estimation of forces from muscle physiological cross-sectional areas and electromyographic data. We have developed a novel approach for loading the Achilles and posterior tibialis tendons that does not prescribe predetermined muscle forces. For our loading model, these muscle forces are determined experimentally using independent plantarflexion and inversion angle feedback control. The independent (input) parameters -- calcaneus plantarflexion, calcaneus inversion, ground reaction forces, and peroneus forces -- are specified. The dependent (output) parameters -- Achilles force, posterior tibialis force, joint motion, and spring ligament strain -- are functions of the independent parameters and the kinematics of the foot and ankle. We have investigated the performance of our model for a single, clinically relevant event during the gait cycle. The instantaneous external forces and foot orientation determined from human subjects in a motion analysis laboratory were simulated in vitro using closed-loop feedback control. Compared to muscle force estimates based on physiological cross-sectional area data and EMG activity at 40% of the gait cycle, the posterior tibialis force and Achilles force required when using position feedback control were greater.     

The effects of alignment of an articulated ankle-foot orthosis on lower limb joint kinematics and kinetics during gait in individuals post-stroke

Mechanical tuning of an ankle-foot orthosis (AFO) is important in improving gait in individuals post-stroke. Alignment and resistance are two factors that are tunable in articulated AFOs. The aim of this study was to investigate the effects of changing AFO ankle alignment on lower limb joint kinematics and kinetics with constant dorsiflexion and plantarflexion resistance in individuals post-stroke. Gait analysis was performed on 10 individuals post-stroke under four distinct alignment conditions using an articulated AFO with an ankle joint whose alignment is adjustable in the sagittal plane. Kinematic and kinetic data of lower limb joints were recorded using a Vicon 3-dimensional motion capture system and Bertec split-belt instrumented treadmill. The incremental changes in the alignment of the articulated AFO toward dorsiflexion angles significantly affected ankle and knee joint angles and knee joint moments while walking in individuals post-stroke. No significant differences were found in the hip joint parameters. The alignment of the articulated AFO was suggested to play an important role in improving knee joint kinematics and kinetics in stance through improvement of ankle joint kinematics while walking in individuals post-stroke. Future studies should investigate long-term effects of AFO alignment on gait in the community in individuals post-stroke.     

Brief communication: Cineradiographic analysis of the chimpanzee (Pan troglodytes) talonavicular and calcaneocuboid joints

During terrestrial locomotion, chimpanzees exhibit dorsiflexion of the midfoot between midstance and toe‐off of stance phase, a phenomenon that has been called the “midtarsal break.” This motion is generally absent during human bipedalism, and in chimpanzees is associated with more mobile foot joints than in humans. However, the contribution of individual foot joints to overall foot mobility in chimpanzees is poorly understood, particularly on the medial side of the foot. The talonavicular (TN) and calcaneocuboid (CC) joints have both been suggested to contribute significantly to midfoot mobility and to the midtarsal break in chimpanzees. To evaluate the relative magnitude of motion that can occur at these joints, we tracked skeletal motion of the hindfoot and midfoot during passive plantarflexion and dorsiflexion manipulations using cineradiography. The sagittal plane range of motion was 38 ± 10° at the TN joint and 14 ± 8° at the CC joint. This finding indicates that the TN joint is more mobile than the CC joint during ankle plantarflexion–dorsiflexion. We suggest that the larger range of motion at the TN joint during dorsiflexion is associated with a rotation (inversion–eversion) across the transverse tarsal joint, which may occur in addition to sagittal plane motion. Am J Phys Anthropol 154:604–608, 2014. © 2014 Wiley Periodicals, Inc.     

Analysis of surface-to-surface distance mapping during three-dimensional motion at the ankle and subtalar joints

Joint surface interaction and ligament constraints determine the kinematic characteristics of the ankle and subtalar joints. Joint surface interaction is characterized by joint contact mechanics and by relative joint surface position potentially characterized by distance mapping. While ankle contact mechanics was investigated, limited information is available on joint distance mapping and its changes during motion. The purpose of this study was to use image-based distance mapping to quantify this interaction at the ankle and subtalar joints during tri-planar rotations of the ankle complex. Five cadaveric legs were scanned using Computed Tomography and the images were processed to produce 3D bone models of the tibia, fibula, talus and calcaneus. Each leg was tested on a special linkage through which the ankle complex was loaded in dorsiflexion/plantarflexion, inversion/eversion, and internal/external rotation and the resulting bone movements were recorded. Fiduciary bone markers data and 3D bone models were combined to generate color-coded distance maps for the ankle and subtalar joints. The results were processed focusing on the changes in surface-to-surface distance maps between the extremes of the range of motion and neutral. The results provided detailed insight into the three-dimensional highly coupled nature of these joints showing significant and unique changes in distance mapping from neutral to extremes of the range of motion. The non-invasive nature of the image-based distance mapping technique could result, after proper modifications, in an effective diagnostic and clinical evaluation technique for application such as ligament injuries and quantifying the effect of arthrodesis or total ankle replacement surgery.     

Models of the geometry of the human ankle bone pulley: two series of geometric models for demonstrating the biomechanics of the ankle joint

2 series of models demonstrate the geometrical shape of the human trochlea tali. We have changed step by step the shape of the 2 flanking articular facets of the trochlea, the course of the edges of the trochlea, and the length of their radii, and so we have found a model responding to the biomechanic conditions of the trochlea tali. The convex surface of this model (corresponding to the superior articular surface, i.e. the facies superior trochleae tali) is a torse, the medial flanking facet (corresponding to the medial articular facet of the trochlea, i.e. the facies malleolaris medialis) is a flat cone, the lateral flanking facet (corresponding to the lateral articular facet of the trochlea, i.e. the facies malleolaris lateralis) is a screwed (helicoidal) face. The resulting model shows the 2 completely different phases of motion in the ankle joint: During dorsiflexion (motion setting out from the neutral position towards the final position of dorsiflexion), the internal malleolus leads the talus, whereas the external malleolus is pushed outwards by the screwed lateral articular facet of the trocheal. The trochlea is moved like a hinge. In the final position of dorsiflexion, the malleoli tightly embrace the 2 flanking facets of the trochlea, whilst an obvious cleft appears dorsally and medially between the superior articular surface of the trochlea and the tibial roof (i.e. the facies articularis inferior tibiae). During plantarflexion (motion setting out from the neutral position towards the final position of plantarflexion), the external malleolus leads the talus, whereas the medial articular facet of the trochlea withdraws from the internal malleolus. The trochlea is moved like a screw. In the final position of plantarflexion, the superior articular surface of the trochlea closely contacts the tibial roof, whilst an obvious cleft appears between the medial articular facet of the trochlea and the internal malleolus.     

The coupled motion of the femur and patella during in vivo weightbearing knee flexion

The movement of the knee joint consists of a coupled motion between the tibiofemoral and patellofemoral articulations. This study measured the six degrees-of-freedom kinematics of the tibia, femur, and patella using dual-orthogonal fluoroscopy and magnetic resonance imaging. Ten normal knees from ten living subjects were investigated during weightbearing flexion from full extension to maximum flexion. The femoral and the patellar motions were measured relative to the tibia. The femur externally rotated by 12.9 deg and the patella tilted laterally by 16.3 deg during the full range of knee flexion. Knee flexion was strongly correlated with patellar flexion (R(2)=0.91), posterior femoral translation was strongly correlated to the posterior patellar translation (R(2)=0.87), and internal-external rotation of the femur was correlated to patellar tilt (R(2)=0.73) and medial-lateral patellar translation (R(2)=0.63). These data quantitatively indicate a kinematic coupling between the tibia, femur, and patella, and provide base line information on normal knee joint kinematics throughout the full range of weightbearing flexion. The data also suggest that the kinematic coupling of tibia, femur, and patella should be considered when investigating patellar pathologies and when developing surgical techniques to treat knee joint diseases.     

A laboratory captured ‘giving way’ episode during a single-leg landing task in an individual with unilateral chronic ankle instability

An episode of ‘giving way’ at the ankle is described as excessive inversion of the rearfoot that does not result in an acute ankle sprain and is a unique feature associated with chronic ankle instability (CAI). Limited data currently exists describing the preparatory movement patterns and those that occur during an episode of ‘giving way. Therefore, this case report describes the movement patterns and the forces generated during an unintentional ‘giving way’ captured while an individual with unilateral CAI was performing a single-leg landing task in a research laboratory. The participant completed five single-leg landing trials for both limbs. 3D lower extremity kinematics and kinetics for the sagittal and frontal plane were extracted from 200 ms before and after initial contact (IC). Relative to the affected and un-affected single-leg landing trials, the ‘giving way’ episode was characterized by an increase in plantarflexion and hip extension moments before and after IC. The plantarflexion deviation dissipated (50 ms post-IC) and was followed by excessive ankle inversion. The ankle began to plantarflex again (150 ms post-IC) and the knee extended (50 ms post-IC) and adducted (100 ms post-IC). As a result, the ankle inversion angle plateaued at 150 ms post-IC. Furthermore, large sagittal plane internal joint moments were observed. In the frontal plane, the ‘giving way’ trial generated a large inversion joint moment which was counteracted by a large internal eversion joint moment. The observed plantarflexion and knee extension and adduction after initial contact likely contributed to preventing the ankle from continuing to invert and avoid an ankle sprain.     

Articular contact at the tibiotalar joint in passive flexion

The knowledge of the contact areas at the tibiotalar articulating surfaces during passive flexion is fundamental for the understanding of ankle joint mobility. Traditional contact area reports are limited by the invasive measuring techniques used and by the complicated loading conditions applied. In the present study, passive flexion tests were performed on three anatomical preparations from lower leg amputation. Roentgen Stereophotogrammetric Analysis was used to accurately reconstruct the position of the tibia and the talus at a number of unconstrained flexion positions. A large number of points was collected on the surface of the tibial mortise and on the trochlea tali by a 3-D digitiser. Articular surfaces were modelled by thin plate splines approximating these points. Relative positions of these surfaces in all the flexion positions were obtained from corresponding bone position data. A distance threshold was chosen to define contact areas. A consistent pattern of contact was found on the articulating surfaces. The area moved anteriorly on both articular surfaces with dorsiflexion. The average position of the contact area centroid along the tibial mortise at maximum plantarflexion and at maximum dorsiflexion was respectively 58% posterior and 40% anterior of the entire antero-posterior length. For increasing dorsiflexion, the contact area moved from medial to lateral in all the specimens.     

The influence of a unilateral fixed ankle on metabolic and mechanical demands during walking in unimpaired young adults

The plantarflexors provide a major source of propulsion during walking. When mechanical power generation from the plantarflexor muscles is limited, other joints may compensate to maintain a consistent walking velocity, but likely at increased metabolic cost. The purpose of this study was to determine how a unilateral reduction in ankle plantarflexor power influences the redistribution of mechanical power generation within and across limbs and the associated change in the metabolic cost of walking. Twelve unimpaired young adults walked with an ankle brace on the dominant limb at 1.2m/s on a dual-belt instrumented treadmill. Lower extremity kinematics and kinetics as well as gas exchange data were collected in two conditions: (1) with the brace unlocked (FREE) and (2) with the brace locked (FIXED). The brace significantly reduced ankle plantarflexion excursion by 12.96±3.60° (p<0.001) and peak ankle mechanical power by 1.03±0.51W/kg (p<0.001) in the FIXED versus FREE condition. Consequently, metabolic power (W/kg) of walking in the FIXED condition increased by 7.4% compared to the FREE condition (p=0.03). Increased bilateral hip mechanical power generation was observed in the FIXED condition (p<0.001). These results suggest that walking with reduced ankle power increases metabolic demand due to the redistribution of mechanical power generation from highly efficient ankle muscle-tendons to less efficient hip muscle-tendons. A within and across limb redistribution of mechanical workload represents a potential mechanism for increased metabolic demand in pathological populations with plantarflexion deficits or those that walk with an ankle-foot orthosis that restricts range of motion.