AFM and electroanalytical studies of synthetic oligonucleotide hybridization

The first and most important step in the development and manufacture of a sensitive DNA-biosensor for hybridization detection is the immobilization procedure of the nucleic acid probe on the transducer surface, maintaining its mobility and conformational flexibility. MAC Mode AFM images were used to demonstrate that oligonucleotide (ODN) molecules adsorb spontaneously at the electrode surface. After adsorption, the ODN layers were formed by molecules with restricted mobility, as well as by superposed molecules, which can lead to reduced hybridization efficiency. The images also showed the existence of pores in the adsorbed ODN film that revealed large parts of the electrode surface, and enabled non-specific adsorption of other ODNs on the uncovered areas. Electrostatic immobilization onto a clean glassy carbon electrode surface was followed by hybridization with complementary sequences and by control experiments with non-complementary sequences, studied using differential pulse voltammetry. The data obtained showed that non-specific adsorption strongly influenced the results, which depended on the sequence of the ODNs. In order to reduce the contribution of non-specific adsorbed ODNs during hybridization experiments, the carbon electrode surface was modified. After modification, the AFM images showed an electrode completely covered by the ODN probe film, which prevented the undesirable binding of target ODN molecules to the electrode surface. The changes of interfacial capacitance that took place after hybridization or control experiments showed the formation of a mixed multilayer that strongly depended on the local environment of the immobilized ODN.     

Electrochemical measurement of DNA hybridization using nanosilver as label and horseradish peroxidase as enhancer

A simple and sensitive electrochemical DNA biosensor based on in situ DNA amplification with nanosilver as label and horseradish peroxide (HRP) as enhancer has been designed. The thiolated oligomer single-stranded DNA (ssDNA) was initially directly immobilized on a gold electrode, and quartz crystal microbalance (QCM) gave the specific amount of ssDNA adsorption of 6.3 ± 0.1 ng/cm². With a competitive format, hybridization reaction was carried out via immersing the DNA biosensor into a stirred hybridization solution containing different concentrations of the complementary ssDNA and constant concentration of nanosilver-labeled ssDNA, and then further binding with HRP. The adsorbed HRP amount on the probe surface decreased with the increment of the target ssDNA in the sample. The hybridization events were monitored by using differential pulse voltammetry (DPV) with the adsorbed HRP toward the reduction of H₂O₂. The reduction current from the enzyme-generated product was related to the number of target ssDNA molecules in the sample. A detection of 15 pmol/L for target ssDNA was obtained with the electrochemical DNA biosensor. Additionally, the developed approach can effectively discriminate complementary from non-complementary DNA sequence, suggesting that the similar enzyme-labeled DNA assay method hold great promises for sensitive electrochemical biosensor applications.     

Comamonas testosteroni strain TI as a potential base for a microbial sensor detecting surfactants

Strain Comamonas testosteroni TI, capable of degrading the nonionic surfactant (NIS) nonylphenolethoxylate (OP-10), was used for constructing a pilot cellular biosensor. The lower NIS detection limit for the biosensor was 0.25 mg/l. We studied the substrate specificity of the biosensor with respect to a wide range of organic compounds: surfactants, polyaromatic compounds (PAC), carbohydrates, alcohols, etc. It was shown that the biosensor based on Comamonas testosteroni TI did not respond to glucose, which was an advantage over the formerly described biosensor based on Pseudomonas rathonis T. The amplitude of the sensor response remained stable for 10 days.     

Development of an amperometric immunosensor for detection of staphylococcal enterotoxin type A in cheese

This paper reports a novel electrochemical immunosensor for the sensitive detection of staphylococcal enterotoxin A (SEA) based on self-assembly monolayer (SAM) and protein A immobilization on gold electrode. Three different methods of protein A immobilization were tested: physical adsorption, cross-linking using glutaraldehyde and covalent binding after activation with N-hydroxysuccinimide (NHS)/N-ethyl-N'-(3-dimethylaminopropyl) carbodiimide hydrochloride (EDC) on cysteamine-modified gold electrode. The EDC/NHS method for protein A immobilization was selected to lead development of the biosensor. The coating steps of the surface modification were characterized by cyclic voltammetry and the biosensor response by chronoamperometry. The advantages of the immunosensor were exposed in its high sensitivity and specificity. The proposed amperometric immunosensor was successfully used for determination of SEA in contaminated and non-contaminated cheese samples with excellent responses.     

Improved procedures for immobilisation of oligonucleotides on gold-coated piezoelectric quartz crystals

The high sensitivity and specificity of DNA hybridisation techniques makes them powerful tools for environmental or clinical analysis. This work describes the development of a DNA piezoelectric biosensor for the detection of the hybridisation reaction. Attention was focused on the choice of the coating chemistry that could be used for the immobilisation of oligonucleotides onto the gold surface of the quartz crystal. Four immobilisation procedures were tested and compared considering the amount of immobilised probe, the extent of the hybridisation reaction, the possibility of regeneration and the absence of non-specific adsorption. All the experiments were performed with oligonucleotides of 25 bases (probe, target and non-complementary oligonucleotide). The four coating methods were all based on the use of self-assembled monolayers (SAM). Three of them employed the interaction between streptavidin and biotin for the immobilisation of a biotinylated probe. Results indicated that immobilisation of a biotinylated probe on streptavidin linked to a layer of carboxylated dextran provides higher sensitivity for the detection of the hybridisation reaction, absence of non-specific adsorption and a higher stability with respect to the regeneration step.     

Ultrasensitive cDNA detection of dengue virus RNA using electrochemical nanoporous membrane-based biosensor

A nanoporous alumina membrane-based ultrasensitive DNA biosensor is constructed using 5'-aminated DNA probes immobilized onto the alumina channel walls. Alumina nanoporous membrane-like structure is carved over platinum wire electrode of 76 μm diameter dimension by electrochemical anodization. The hybridization of complementary target DNA with probe DNA molecules attached inside the pores influences the pore size and ionic conductivity. The biosensor demonstrates linear range over 6 order of magnitude with ultrasensitive detection limit of 9.55×10(-12) M for the quantification of ss-31 mer DNA sequence. Its applicability is challenged against real time cDNA PCR sample of dengue virus serotype1 derived from asymmetric PCR. Excellent specificity down to one nucleotide mismatch in target DNA sample of DENV3 is also demonstrated.     

Comamonas testosteroni Strain TI as a Potential Base for a Microbial Sensor Detecting Surfactants

Strain Comamonas testosteroni TI, capable of degrading the nonionic surfactant (NIS) nonylphenolethoxylate (OP-10), was used for constructing a pilot cellular biosensor. The lower NIS detection limit for the biosensor was 0.25 mg/l. We studied the substrate specificity of the biosensor with respect to a wide range of organic compounds: surfactants, polyaromatic compounds (PAC), carbohydrates, alcohols, etc. It was shown that the biosensor based on Comamonas testosteroni TI did not respond to glucose, which was an advantage over the formerly described biosensor based on Pseudomonas rathonis T. The amplitude of the sensor response remained stable for 10 days.     

Development of an electrochemical DNA biosensor with a high sensitivity of fM by dendritic gold nanostructure modified electrode

In this paper, dendritic gold nanostructure (DenAu) modified electrode was obtained by direct electrodeposition of planar electrode into 2.8 mM HAuCl(4) and 0.1 M H(2)SO(4) solution under a very negative potential of -1.5 V. Scanning electron microscopy was used to characterize the growth evolution of DenAu with time. The whole DNA biosensor fabrication process based on the DenAu modified electrode was characterized by cyclic voltammetry and electrochemical impedance spectroscopy methods with the use of ferricyanide as an electrochemical redox indicator. The probe DNA immobilization and hybridization with target DNA on the modified electrode could be well distinguished by using methylene blue as an electrochemical hybridization indicator. The DenAu modified electrode could realize an ultra sensitivity of 1 fM toward complementary target DNA and a very wide dynamic detection range (from 1 fM to 1 nM).     

Design of a sandwich-mode amperometric biosensor for detection of PML/RARα fusion gene using locked nucleic acids on gold electrode

In this study, a novel DNA electrochemical probe (locked nucleic acid, LNA) was designed and involved in constructing an electrochemical DNA biosensor for detection of promyelocytic leukemia/retinoic acid receptor alpha (PML/RARα) fusion gene in acute promyelocytic leukemia for the first time. This biosensor was based on a 'sandwich' sensing mode, which involved a pair of LNA probes (capture probe immobilized at electrode surface and biotinyl reporter probe as an affinity tag for streptavidin-horseradish peroxidase (streptavidin-HRP). Since biotin can be connected with streptavidin-HRP, this biosensor offered an enzymatically amplified electrochemical current signal for the detection of target DNA. In the simple hybridization system, DNA fragment with its complementary DNA fragment was evidenced by amperometric detection, with a detection limit of 74 fM and a linear response range of 0.1-10 pM for synthetic PML/RARα fusion gene in acute promyelocytic leukemia (APL). Otherwise, the biosensor showed an excellent specificity to distinguish the complementary sequence and different mismatch sequences. The new pattern also exhibited high sensitivity and selectivity in mixed hybridization system.     

Electrochemical DNA biosensor for detecting cancer biomarker related to glutathione S-transferase P1 (GSTP1) hypermethylation in real samples

An electrochemical genosensor for the detection of hypermethylation of the glutathione S-transferase P1 (GSTP1) gene, a specific marker of prostate cancer, was reported. This new sensor was used in combination with a single-use carbon graphite working electrode and differential pulse voltammetry, with the results of sample analysis based on the guanine oxidation signals obtained at +1.0 V before and after hybridization between probe and synthetic target or denatured PCR samples. The detected DNA hybridization was also characterized by electrochemical impedance spectroscopy with potassium ferri/ferrocyanide as a redox probe. The protocol consisted of 2 different modes: (i) capture probes selective for methylation-specific and unmethylated GSTP1 sequences were immobilized onto the sensor directly, and hybridization was formed on the electrode surface; (ii) probe/target or probe/noncomplementary target couples were mixed in solution phase, and the transducer was modified through simple adsorption. The limit of detection (S/N=3) was calculated as 2.92 pmol of target sequence in a 100-μl reaction volume. The optimum analytical detection parameters for the biosensor, as well as its future prospects, were also presented.     

Ultrasensitive and label-free detection of pathogenic avian influenza DNA by using CMOS impedimetric sensors

This work presents miniaturized CMOS (complementary metal oxide semiconductor) sensors for non-faradic impedimetric detection of AIV (avian influenza virus) oligonucleotides. The signal-to-noise ratio is significantly improved by monolithic sensor integration to reduce the effect of parasitic capacitances. The use of sub-μm interdigitated microelectrodes is also beneficial for promoting the signal coupling efficiency. Capacitance changes associated with surface modification, functionalization, and DNA hybridization were extracted from the measured frequency responses based on an equivalent-circuit model. Hybridization of the AIV H5 capture and target DNA probes produced a capacitance reduction of -13.2 ± 2.1% for target DNA concentrations from 1 fM to 10 fM, while a capacitance increase was observed when H5 target DNA was replaced with non-complementary H7 target DNA. With the demonstrated superior sensing capabilities, this miniaturized CMOS sensing platform shows great potential for label-free point-of-care biosensing applications.     

Deep oxidation of glucose in enzymatic fuel cells through a synthetic enzymatic pathway containing a cascade of two thermostable dehydrogenases

A sensitive glutamate biosensor is prepared based on glutamate dehydrogenase/vertically aligned carbon nanotubes (GLDH, VACNTs). Vertically aligned carbon nanotubes were grown on a silicon substrate by direct current plasma enhanced chemical vapor deposition (DC-PECVD) method. The electrochemical behavior of the synthesized VACNTs was investigated by cyclic voltammetry and electrochemical impedance spectroscopic methods. Glutamate dehydrogenase covalently attached on tip of VACNTs. The electrochemical performance of the electrode for detection of glutamate was investigated by cyclic and differential pulse voltammetry. Differential pulse voltammetric determinations of glutamate are performed in mediator-less condition and also, in the presence of 1 and 5 μM thionine as electron mediator. The linear calibration curve of the concentration of glutamate versus peak current is investigated in a wide range of 0.1-500 μM. The mediator-less biosensor has a low detection limit of 57 nM and two linear ranges of 0.1-20 μM with a sensitivity of 0.976 mA mM(-1) cm(-2) and 20-300 μM with a sensitivity of 0.182 mA mM(-1) cm(-2). In the presence of 1 μM thionine as an electron mediator, the prepared biosensor shows a low detection limit of 68 nM and two linear ranges of 0.1-20 with a calibration sensitivity of 1.17 mA mM(-1) cm(-2) and 20-500 μM with a sensitivity of 0.153 mA mM(-1) cm(-2). The effects of the other biological compounds on the voltammetric behavior of the prepared biosensor and its response stability are investigated. The results are demonstrated that the GLDH/VACNTs electrode even without electron mediator is a suitable basic electrode for detection of glutamate.     

Enzymatic amplification detection of DNA based on "molecular beacon" biosensors

We described a novel electrochemical DNA biosensor based on molecular beacon (MB) probe and enzymatic amplification protocol. The MB modified with a thiol at its 5' end and a biotin at its 3' end was immobilized on the gold electrode through mixed self-assembly process. Hybridization events between MB and target DNA cause the conformational change of the MB, triggering the attached biotin group on the electrode surface. Following the specific interaction between the conformation-triggered biotin and streptavidin-horseradish peroxidase (HRP), subsequent quantification of DNA was realized by electrochemical detection of enzymatic product in the presence of substrate. The detection limit is obtained as low as 0.1nM. The presented DNA biosensor has good selectivity, being able to differentiate between a complementary target DNA sequence and one containing G-G single-base mismatches.     

An electrochemical biosensor for 3-hydroxybutyrate detection based on screen-printed electrode modified by coenzyme functionalized carbon nanotubes

3-Hydroxybutyrate, one of the main blood ketone bodies, has been considered as a critical indicator for diagnosis of diabetic ketoacidosis. Biosensors designed for detection of 3-hydroxybutyrate with advantages of precision, easiness and speedy performance have attracted increasing attention. This study attempted to develop a 3-hydroxybutyrate dehydrogenase-based biosensor in which single-walled carbon nanotubes (SWCNT) was used in order to immobilize the cofactor, NAD⁺, on the surface of screen-printed electrode. The formation of NAD⁺–SWCNT conjugates was assessed by electrochemistry and electron microscopy. Cyclic voltammetry was used to analyze the performance of this biosensor electrochemically. The considerable shelf life and reliability of the proposed biosensor to analyze real sample was confirmed by this method. The reduction in the over potential of electrochemical oxidation of NADH to ?0.15 V can be mentioned as a prominent feature of this biosensor. This biosensor can detect 3-hydroxybutyrate in the linear range of 0.01–0.1 mM with the low detection limit of 0.009 mM. Simultaneous application of screen-printed electrode and SWCNT has made the biosensor distinguished which can open new prospects for detection of other clinically significant metabolites.     

An amperometric biosensor based on laccase immobilized onto Fe(3)O(4)NPs/cMWCNT/PANI/Au electrode for determination of phenolic content in tea leaves extract

A method is described for the construction of an amperometric biosensor for detection of phenolic compounds based on covalent immobilization of laccase onto iron oxide nanoparticles (Fe(3)O(4)NPs) decorated carboxylated multiwalled carbon nanotubes (cMWCNTs)/polyaniline (PANI) composite electrodeposited onto a gold (Au) electrode. The modified electrode was characterized by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response within 3s at pH 6.0 (0.1M sodium acetate buffer) and 35°C, when operated at 0.3V vs. Ag/AgCl. Linear range, detection limit were 0.1-10μM (lower concentration range) and 10-500μM (higher concentration range), and 0.03μM respectively. The sensor measured total phenolic content in tea leaves extract. The enzyme electrode lost 25% of its initial activity after its 150 uses over a period of 4 months, when stored at 4°C.     

An amperometric biosensor based on laccase immobilized onto MnO2NPs/cMWCNT/PANI modified Au electrode

A method is described for construction of an amperometric biosensor for detection of phenolic compounds based on covalent immobilization of laccase (Lac) onto manganese dioxide nanoparticles (MnO(2)NPs) decorated carboxylated multiwalled carbon nanotubes (cMWCNTs)/PANI composite electrodeposited onto a gold (Au) electrode through N-ethyl-N'-(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydroxy succinimide (NHS) chemistry. The modified electrode was characterized by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The biosensor showed optimum response at pH 5.5 (0.1M sodium acetate buffer) and 35°C, when operated at 0.3 V vs. Ag/AgCl. Linear range, response time, detection limit were 0.1-10 μM (lower concentration range) and 10-500 μM (higher concentration range), 4s and 0.04 μM, respectively. Biosensor measured total phenolic content in tea leaves extract. The enzyme electrode was used 150 times over a period of 5 months.     

Immobilization of rat brain acetylcholinesterase on porous gold-nanoparticle-CaCO₃ hybrid material modified Au electrode for detection of organophosphorous insecticides

An acetylcholinesterase (AChE) purified from rat brain was immobilized onto gold nanoparticles (AuNPs) assembled on the surface of porous calcium carbonate (CaCO₃) microsphere. The resulting AChE-AuNPs-CaCO₃ bioconjugate was mounted on the surface of Au electrode with the help of silica sol-gel matrix to prepare the working electrode. This electrode was connected to Ag/AgCl (3 M/saturated KCl) as standard and Pt wire as an auxiliary electrode through a potentiostat to construct an organophosphorus (OP) biosensor. The biosensor was based on inhibition of AChE by OP compounds/insecticides. The biosensor showed optimum response at pH 7.0, 30 °C, when polarized at +0.2 V. Two OP compounds, malathion and chlorpyrifos could be detected in the range of 0.1-100 nM and 0.1-70 nM, respectively at 2.0-3.0% inhibition level of AChE. The sensor was reactivated by immersing it in 0.1 mM 2-pyridine aldoxime for 10 min. The detection limit of the sensor was 0.1 nM for both malathion and chlorpyrifos. The biosensor exhibited good reusability (50 times without considerable loss) and storage stability (50% within 60 days, when stored at 4 °C).     

Porous silicon-based biosensor for pathogen detection

A porous silicon-based biosensor for rapid detection of bacteria was fabricated. Silicon (0.01 ohmcm, p-type) was anodized electrochemically in an electrochemical Teflon cell containing ethanoic hydrofluoric acid solution to produce sponge-like porous layer of silicon. Anodizing conditions of 5 mA/cm2 for 85 min proved best for biosensor fabrication. A single-tube chemiluminescence-based assay, previously developed, was adapted to the biosensor for detection of Escherichia coli. Porous silicon chips were functionalized with a dioxetane-Polymyxin B (cell wall permeabilizer) mixture by diffusion and adsorption on to the porous surface. The reaction of beta-galactosidase enzyme from E. coli with the dioxetane substrate generated light at 530 nm. Light emission for the porous silicon biosensor chip with E. coli was significantly greater than that of the control and planar silicon chip with E. coli (P<0.01). Sensitivity of the porous silicon biosensor was determined to be 101-102 colony forming units (CFU) of E. coli. The porous silicon-based biosensor was fabricated and functionalized to successfully detect E. coli and has potential applications in food and environmental testing.     

Biosensing under an applied voltage using optical waveguide lightmode spectroscopy

An applied dc voltage offers a means of controlling immobilization during biosensor fabrication and detection during biosensing application. We present a method to directly and continuously measure the adsorption of biomacromolecules or other polyelectrolytes, under an applied potential difference, based on optical waveguide lightmode spectroscopy (OWLS). An indium tin oxide (ITO) film of thickness ca. 10 nm coated onto a silicon titanium oxide (STO) waveguiding film serves as the working (sensing) electrode. We observe the effective refractive index of the 0th transverse electric guided mode to increase significantly in the presence of an applied potential due to charging of the interfacial double layer and, possibly, modest electrochemical oxidation. Adsorption from solution onto the ITO electrode is detected by a further increase in the effective refractive index. We achieve accurate detection by employing an optical model in which the STO and ITO layers are combined into a single waveguiding film. No improvement is found using models treating the ITO as a separate layer, either dielectric or conducting. Using this method, we find the adsorption of human serum albumin and horse heart cytochrome c to be considerably enhanced in the presence of an applied potential exceeding 1 V. We attribute this behavior to adsorption at positions on the protein molecules of complementary charge.     

P450-based porous silicon biosensor for arachidonic acid detection

A porous silicon biosensor based on P450 enzyme for arachidonic acid detection was developed. A new transduction method is presented with a simultaneous measurement of refractive index and fluorescence intensity changes when the analyte is binding to an enzyme on the porous silicon surface. A fluorophore bound to a cysteine residue in an allosteric position of the haem domain (BMP) of cytochrome P450 BM3 enhances its fluorescence intensity upon interaction with its substrate arachidonic acid, involved in diseases such as Alzheimer's, liver cancer and cellular inflammation processes. BMP has been anchored on porous silicon surface and the new transduction method has been successfully exploited to develop a biosensor for arachidonic acid, reaching a detection limit of 10 μM arachidonic acid in a dynamic range of 10-200 μM. Moreover, the change of the refractive index has been also monitored at the same time, displaying a higher detection limit of 30 μM. Preliminary test were also conducted in plasma proving the high specificity and selectivity of the sensor even in presence of interferents in the range of 50-100 μM. Here we suggest these two detection systems could be used simultaneously to increase the accuracy and the dynamic range of the sensor avoiding a false positive response.