微生物燃料电池中产电微生物的研究进展

产电微生物是微生物燃料电池系统的核心组成, 本文从生物学角度介绍了几种产电微生物的分类学地位、形态特征、生理生化特征及在微生物燃料电池中的产电机理和产电能力, 分析了利用产电微生物进行废水处理同时生物发电的应用前景, 提出产电微生物在MFC系统中的进一步研究方向为微生物的富集、驯化、改造和多种菌种优化组合等。     

微生物燃料电池阳极产电微生物和阴极受体特性及研究进展

介绍微生物燃料电池的基本工作原理。根据电子传递方式阳极产电微生物分为无需中间体微生物和需中间体微生物。对阴极进行不同反应所涉及的最终电子受体进行了概述,并展望了微生物燃料电池的应用前景。     

利用异化金属还原菌构建含糖微生物燃料电池

环境中的一些微生物通过还原金属氧化物进行无氧呼吸,而石墨电极与金属氧化物相似,也可以作为这类微生物呼吸作用的最终电子受体,利用这类微生物构建微生物燃料电池,以糖类物质为燃料,对电池产电情况、产电原理进行研究。实验结果表明,以Rhodoferaxferrireducens为产电微生物,在外接电阻510Ω条件下,以葡萄糖为燃料,常温下产生的电流密度达158mAm2(平台电压为0.46V,电极有效接触表面积为57cm2),且循环性能良好。更换燃料为其它糖,发现微生物可以利用多种糖进行产电;通过SEM观察发现大量微生物吸附在石墨电极上,用Bradford法对运行20d后电池的细胞量进行定量,测得悬浮细胞蛋白浓度为140mgL,吸附在电极上的生物量为1180mgm2。通过数据采集分析和细菌还原实验,发现吸附在电极上的微生物对电压的产生贡献最大,具有电化学和生物学活性;悬浮细胞对产电贡献很小,不具有电化学和生物学活性。     

微生物燃料电池在固体废物堆肥中的应用进展

微生物燃料电池(Microbial fuel cell,MFC)是一种近几年快速发展的废物处理与能源化技术,可以与污水处理、污染物降解、脱盐等环境技术结合。微生物燃料电池与堆肥技术结合可以在处理日益增长的固体废弃物的同时回收能量,具有很好的发展前景。文中分析了堆肥微生物燃料电池系统的微生物特征,探讨了堆肥过程中影响微生物燃料电池产电性能的因素,包括电极,隔膜,供氧和构型。最后归纳说明了堆肥微生物电池作为一种新的废弃物处理技术的特点:较高的微生物量并可产生较高的电流密度;对不同环境的适应性强;可以自身调节温度,能源利用效率高;质子从阳极向阴极的移动会受到不同堆肥原料的影响。     

纳米材料修饰微生物燃料电池阳极的研究进展

阳极作为微生物燃料电池中的重要组成部分,其性能的高低显著影响着微生物燃料电池的产电性能。纳米材料具有导电性好、表面积大等优良特性。因此,纳米材料修饰阳极能够有效减小电极内阻、增大微生物的粘附量,从而显著提高微生物燃料电池的产电性能。本文首先简要介绍了微生物燃料电池中阳极修饰纳米材料的种类,然后重点归纳了不同纳米材料修饰阳极对微生物燃料电池产电性能的影响及其原因。最后对微生物燃料电池阳极修饰纳米材料和技术进行展望。     

产电菌群及电子受体对微生物燃料电池性能的影响

采用2种类型的微生物燃料电池--常规微生物燃料电池(S-MFCs,以生活污水作为产电菌群接种源、以硝酸盐作为电子受体）和改进后的微生物燃料电池（A-MFCs,以厌氧发酵液作为产电菌群接种源、以铁氰化物作为电子受体）,分析了产电菌群和电子受体的改进对微生物燃料电池产电性能的影响.结果表明：产电菌群和电子受体对MFCs驯化周期和运行周期具有显著影响,使驯化周期由S-MFCs的500 h缩短到A-MFCs的430 h,运行周期由S-MFCs的100 h增加到A-MFCs的350 h;改进后的微生物燃料电池使COD去除率提升了25%,使电压输出提高了约300%.选择合适的产电菌菌种和电子受体标准电极电势是微生物燃料电池性能提升的基础.     

关于微生物燃料电池底物的研究进展

近年来,微生物燃料电池已引起了广泛关注,它将低能量废水和木质纤维素生物质等有机废物转化为电能。在将来,微生物电能将成为一种重要的生物能源,因为微生物燃料电池提供了一种复合有机物和可再生生物能源中提取电能的可行性。人们研究了许多物质,以考察其是否能作为微生物电能转化的底物。这些物质包括人工的和天然废物,以及木质纤维素生物质。尽管现在微生物燃料电池提供的电流和功率较低,但是随着技术的发展和对微生物燃料电池系统的深入了解,微生物燃料电池转化的电流和电力将极大增加,从而向世人提供了一种可以将纤维素生物质和废水直接转化为有用能源的有效方法。本文介绍了迄今为止在微生物燃料电池中用到的各种反应底物,并对它们的应用效率和存在的不足进行了分析。     

微生物燃料电池在毒性物质检测中的应用

微生物燃料电池(Microbial fuel cell,MFC)利用微生物整体作为催化剂催化底物将化学能直接转化为电能,是一种极具应用前景的生物电化学技术。微生物在阳极氧化还原有机物产生电子并传递给阳极,电子通过外电路传递至阴极后将电子释放给阴极中的氧化剂,从而产生电流。当有毒物质进入MFC,微生物活性降低,电子传递量变少,电流降低,而电流的产生与微生物活性呈线性关系,据此可检测样品的毒性。本文主要介绍了微生物燃料电池在毒性物质抗生素、重金属离子、有机污染物、酸等方面的研究,并分析了微生物燃料电池存在的问题及未来研究方向,以期不久的将来微生物燃料电池能付之使用。     

人工湿地-微生物燃料电池耦合系统的研究进展

人工湿地-微生物燃料电池耦合系统(CW-MFC)是一种将人工湿地技术(CW)和微生物燃料电池技术(MFC)结合在一起的新型污水处理系统,其产电机理是产电微生物在底层湿地(阳极)的厌氧条件下生成电子,通过外电路传递到表面湿地(阴极)完成氧化还原反应。但是,近几年来,关于CW-MFC研究的文章较少且研究深度较浅。综述了电极材料、水力条件、湿地植物及微生物等条件对CW-MFC污水处理能力和产电能力的影响。在电极材料方面,选用导电性、吸附性及有效面积大的材料作为电极可有效提高CW-MFC产电与去污能力;在水利条件方面,在HRT为2-3 d的条件下,应选用升流式或升流-降流式的入水方式;湿地植物方面,种植湿地植物的CW-MFC在去污和产电能力上都要优于未种植植物的CW-MFC;微生物方面,阴极与阳极的微生物群落结构存在明显的差异,但存在的产电菌的种类却十分相似。CW-MFC中存在的常见产电微生物主要包括地杆菌属(Geobacter)、脱硫叶菌属(Desulfobulbus)、假单胞菌属(Pseudomona)和脱硫弧菌属(Desulfovibrio)等。最后对CW-MFC的研究方向进行了分析,以期为CW-MFC的实际应用提供理论依据。     

微生物燃料电池内阻及其影响因素分析

微生物燃料电池(MFC)是一种通过微生物的催化作用将有机物中的化学能直接转化为电能的生物反应装置,研究表明内阻是限制微生物燃料电池产能的重要因素。本文对目前国内外有关微生物燃料电池内阻的研究成果进行了总结,系统介绍了微生物燃料电池内阻定义、构成和常用的微生物燃料电池内阻测定方法,重点分析了反应器、产电底物、产电微生物和操作条件等对微生物燃料电池内阻的影响,并结合已有的研究结果提出了降低内阻、提高微生物燃料电池产电性能的可行性方法。     

Gaseous pollutant treatment and electricity generation in microbial fuel cells (MFCs) utilising redox mediators

Microbial fuel cell (MFC) is an emerging technology for sustainable energy generation and waste treatment. This paper reviews the potential of a gaseous substrate when it is combined with a mediator in an MFC to generate electricity and to treat toxic gaseous pollutants. Most MFCs for waste water treatment often cannot use mediator to enhance the electron transfer from the microbe to the anode because of the difficulty in recovering the expensive and potentially toxic compound. Combining gas feeds with mediators is possible since the soluble mediator would remain in the anode chamber as the gas passes through the reactor. In addition, this type of MFC is possible to be integrated into an anaerobic biofiltration system (BF-MFC), where the biofilter removes the gaseous contaminant and produces the reduced mediator and the MFC produces the electricity and recycles the reoxidised mediator. This paper also talks about the past research on gaseous feed MFCs, and reviews the mechanism and strategies of electron transfer in MFC using redox mediator. The advantages, process parameters and challenges of BF-MFC are discussed. This knowledge is very much required in the design and scale up of BF-MFC. This paper will be useful for those who work in the area of gaseous pollutant treatment and electricity generation.     

New exoelectrogen Citrobacter sp. SX-1 isolated from a microbial fuel cell

Aims: Isolation, identification and characterization of a new exoelectrogenic bacterium from a microbial fuel cell (MFC). Methods and Results: Exoelectrogenic bacterial strain SX‐1 was isolated from a mediator‐less MFC by conventional plating techniques with ferric citrate as electron acceptor under anaerobic condition. Phylogenetic analysis of the 16S rDNA sequence revealed that it was related to the members of Citrobacter genus with Citrobacter sp. sdy‐48 being the most closely related species. The bacterial strain SX‐1 produced electricity from citrate, acetate, glucose, sucrose, glycerol and lactose in MFCs with the highest current density of 205 mA m^?2 generated from citrate. Cyclic voltammetry analysis indicated that membrane‐associated proteins may play an important role in facilitating the electrons transferring from bacteria to electrode. Conclusions: This is the first study that demonstrates that Citrobacter species can transfer electrons to extracellular electron acceptors. Citrobacter strain SX‐1 is capable of generating electricity from a wide range of substrates in MFCs. Significance and Impact of the Study: This finding increases the known diversity of power generating exoelectrogens and provided a new strain to explore the mechanisms of extracellular electron transfer from bacteria to electrode. The wide range of substrate utilization by SX‐1 increases the application potential of MFCs in renewable energy generation and waste treatment.     

Impedance spectroscopy as a tool for non‐intrusive detection of extracellular mediators in microbial fuel cells

Endogenously produced, diffusible redox mediators can act as electron shuttles for bacterial respiration. Accordingly, the mediators also serve a critical role in microbial fuel cells (MFCs), as they assist extracellular electron transfer from the bacteria to the anode serving as the intermediate electron sink. Electrochemical impedance spectroscopy (EIS) may be a valuable tool for evaluating the role of mediators in an operating MFC. EIS offers distinct advantages over some conventional analytical methods for the investigation of MFC systems because EIS can elucidate the electrochemical properties of various charge transfer processes in the bio‐energetic pathway. Preliminary investigations of Shewanella oneidensis DSP10‐based MFCs revealved that even low quantities of extracellular mediators significantly influence the impedance behavior of MFCs. EIS results also suggested that for the model MFC studied, electron transfer from the mediator to the anode may be up to 15 times faster than the electron transfer from bacteria to the mediator. When a simple carbonate membrane separated the anode and cathode chambers, the extracellular mediators were also detected at the cathode, indicating diffusion from the anode under open circuit conditions. The findings demonstrated that EIS can be used as a tool to indicate presence of extracellular redox mediators produced by microorganisms and their participation in extracellular electron shuttling. Biotechnol. Bioeng. 2009; 104: 882–891. © 2009 Wiley Periodicals, Inc.     

A kinetic perspective on extracellular electron transfer by anode-respiring bacteria

In microbial fuel cells and electrolysis cells (MXCs), anode-respiring bacteria (ARB) oxidize organic substrates to produce electrical current. In order to develop an electrical current, ARB must transfer electrons to a solid anode through extracellular electron transfer (EET). ARB use various EET mechanisms to transfer electrons to the anode, including direct contact through outer-membrane proteins, diffusion of soluble electron shuttles, and electron transport through solid components of the extracellular biofilm matrix. In this review, we perform a novel kinetic analysis of each EET mechanism by analyzing the results available in the literature. Our goal is to evaluate how well each EET mechanism can produce a high current density (>10 A m⁻²) without a large anode potential loss (less than a few hundred millivolts), which are feasibility goals of MXCs. Direct contact of ARB to the anode cannot achieve high current densities due to the limited number of cells that can come in direct contact with the anode. Slow diffusive flux of electron shuttles at commonly observed concentrations limits current generation and results in high potential losses, as has been observed experimentally. Only electron transport through a solid conductive matrix can explain observations of high current densities and low anode potential losses. Thus, a study of the biological components that create a solid conductive matrix is of critical importance for understanding the function of ARB.     

Microbial fuel cells: novel biotechnology for energy generation

Microbial fuel cells (MFCs) provide new opportunities for the sustainable production of energy from biodegradable, reduced compounds. MFCs function on different carbohydrates but also on complex substrates present in wastewaters. As yet there is limited information available about the energy metabolism and nature of the bacteria using the anode as electron acceptor; few electron transfer mechanisms have been established unequivocally. To optimize and develop energy production by MFCs fully this knowledge is essential. Depending on the operational parameters of the MFC, different metabolic pathways are used by the bacteria. This determines the selection and performance of specific organisms. Here we discuss how bacteria use an anode as an electron acceptor and to what extent they generate electrical output. The MFC technology is evaluated relative to current alternatives for energy generation.     

Evaluation of procedures to acclimate a microbial fuel cell for electricity production

A microbial fuel cell (MFC) is a relatively new type of fixed film bioreactor for wastewater treatment, and the most effective methods for inoculation are not well understood. Various techniques to enrich electrochemically active bacteria on an electrode were therefore studied using anaerobic sewage sludge in a two-chambered MFC. With a porous carbon paper anode electrode, 8 mW/m² of power was generated within 50 h with a Coulombic efficiency (CE) of 40%. When an iron oxide-coated electrode was used, the power and the CE reached 30 mW/m² and 80%, respectively. A methanogen inhibitor (2-bromoethanesulfonate) increased the CE to 70%. Bacteria in sludge were enriched by serial transfer using a ferric iron medium, but when this enrichment was used in a MFC the power was lower (2 mW/m²) than that obtained with the original inoculum. By applying biofilm scraped from the anode of a working MFC to a new anode electrode, the maximum power was increased to 40 mW/m². When a second anode was introduced into an operating MFC the acclimation time was not reduced and the total power did not increase. These results suggest that these active inoculating techniques could increase the effectiveness of enrichment, and that start up is most successful when the biofilm is harvested from the anode of an existing MFC and applied to the new anode.     

Characterization of electrochemical activity of a strain ISO2‐3 phylogenetically related to Aeromonas sp. isolated from a glucose‐fed microbial fuel cell

The microbial communities associated with electrodes in closed and open circuit microbial fuel cells (MFCs) fed with glucose were analyzed by 16S rRNA approach and compared. The comparison revealed that bacteria affiliated with the Aeromonas sp. within the Gammaproteobacteria constituted the major population in the closed circuit MFC (harvesting electricity) and considered to play important roles in current generation. We, therefore, attempted to isolate the dominant bacteria from the anode biofilm, successfully isolated a Fe (III)‐reducing bacterium phylogenetically related to Aeromonas sp. and designated as strain ISO2‐3. The isolated strain ISO2‐3 could grow and concomitantly produce current (max. 0.24 A/m²) via oxidation of glucose or hydrogen with an electrode serving as the sole electron acceptor. The strain could ferment glucose, but generate less electrical current. Cyclic voltammetry supported the strain ISO2‐3 was electrically active and likely to transfer electrons to the electrode though membrane‐associated compounds (most likely c‐type cytochrome). This mechanism requires intimate contact with the anode surface. Scanning electron microscopy revealed that the strain ISO2‐3 developed multiplayer biofilms on the anode surface and also produced anchor‐like filamentous appendages (most likely pili) that may promote long‐range electron transport across the thick biofilm. Biotechnol. Bioeng. 2009; 104: 901–910. © 2009 Wiley Periodicals, Inc.     

Enhanced wastewater treatment efficiency through microbially catalyzed oxidation and reduction: synergistic effect of biocathode microenvironment

Microbially catalyzed treatment of wastewater was evaluated in both the anode and cathode chambers in dual chambered microbial fuel cell (MFC) under varying biocathode microenvironment. MFC operation with aerobic biocathode showed significant increment in both TDS (cathode, 90.2±1%; anode, 39.7±0.5%) and substrate (cathode, 98.07±0.06%; anode, 96.2±0.3%) removal compared to anaerobic biocathode and abiotic cathode operations (COD, 80.25±0.3%; TDS, 30.5±1.2%). Microbially catalyzed reduction of protons and electrons at cathode will be higher during aerobic biocathode operation which leads to gradual substrate removal resulting in stable bio-potential for longer periods facilitating salts removal. Bio-electro catalytic behavior showed higher exchange current density during aerobic biocathode operation resulting in induced electrochemical oxidation which supports the enhanced treatment. Anaerobic biocathode operation depicted relatively less TDS removal (anode, 16.35%; cathode, 16.04%) in both the chambers in spite of good substrate degradation (anode, 84%; cathode, 87.39%). Both the chambers during anaerobic biocathode operation competed as electron donors resulting in negligible bio-potential development.     

Continuous power generation and microbial community structure of the anode biofilms in a three-stage microbial fuel cell system

A mediator-less three-stage two-chamber microbial fuel cell (MFC) system was developed and operated continuously for more than 1.5 years to evaluate continuous power generation while treating artificial wastewater containing glucose (10 mM) concurrently. A stable power density of 28 W/m³ was attained with an anode hydraulic retention time of 4.5 h and phosphate buffer as the cathode electrolyte. An overall dissolved organic carbon removal ratio was about 85%, and coulombic efficiency was about 46% in this MFC system. We also analyzed the microbial community structure of anode biofilms in each MFC. Since the environment in each MFC was different due to passing on the products to the next MFC in series, the microbial community structure was different accordingly. The anode biofilm in the first MFC consisted mainly of bacteria belonging to the Gammaproteobacteria, identified as Aeromonas sp., while the Firmicutes dominated the anode biofilms in the second and third MFCs that were mainly fed with acetate. Cyclic voltammetric results supported the presence of a redox compound(s) associated with the anode biofilm matrix, rather than mobile (dissolved) forms, which could be responsible for the electron transfer to the anode. Scanning electron microscopy revealed that the anode biofilms were comprised of morphologically different cells that were firmly attached on the anode surface and interconnected each other with anchor-like filamentous appendages, which might support the results of cyclic voltammetry. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Microfluidic electroporation for delivery of small molecules and genes into cells using a common DC power supply

The end-product profile of the glucose fermentation by Propionibacterium freudenreichii ET-3 changed on an electrochemical treatment, in which the culture vessel was filled with a carbon felt anode. Acetate and propionate were produced as final end products in a molar ratio of 2:3 without any electrochemical treatments at the point of the consumption of lactate as an intermediate of the glucose fermentation. The ratio was changed to 1:1 at the point of the lactate consumption by the electrochemical incubation at an electrode potential of 0.4 V versus Ag|AgCl for 100 h. During further electrochemical incubation, propionate was oxidized to acetate as a final end-product in the microbe-containing anode chamber. 1,4-Dihydroxy-2-naphthoic acid produced by P. freudenreichii ET-3 itself would receive electrons from the metabolic pathway and serve as an electron transfer mediator from the microbial cells to the electrode.